Search Documents

By N. V. Hansell

l. INTRODUCTION. THE last few years have shown an increasing interest in the subject of beneficiating iron-ores -in all iron-producing countries. In the United States, this movement has been slower than in certain parts of Europe, for the obvious reason that the abundance and relative cheapness of the Lake Superior iron ores has hindered the development of enterprises for the preparation of low-grade ores. Gradually, however, conditions have changed. The world's consumption of iron is increasing enormously. Being in 1900 about 40,000,000 tons, in 1910 ii was already 60,000000; and there is no reason to doubt that for the near future the increase in iron-consumption will continue at the same rapid rate, especially with, the development of China, certain parts of Africa, and other regions which have hardly been touched as yet by modern industrialism. It is. therefore, not surprising that apprehension is felt that the known available iron-ore resources of the world are gradually being depleted. Signs of this feeling are the recent investigation, under the direction of the U. S. Geological Survey, of the iron-ore resources of the United States, and the estimate presented to the last International Geological Congress, at Stockholm, Sweden, of the iron-ore resources of the world. These investigations have emphasized the fact that the known high-grade ore-deposits are limited in extent, and will, at a not distant future, be exhausted, compelling the iron industry to depend for raw material on the enormous deposits of low-grade ores which are distributed over almost all the world. The discovery of new deposits of high-grade ore, in countries not yet thoroughly explored, will not materially change this prospect. Of course, the part which such new deposits will play in the future cannot be forecast. The difficulty and cost of transportation will probably exclude many of them from use at the present centers of the iron industry.

May 1, 1912

By Casper A. Nelson, Wendell M. Whitecotton

A WIDE variety of lead ore is treated by the Midvale Smelter, for it is a custom plant not only treating Company lead concentrate and direct-smelting ores but also custom ores and concentrates, principally from Utah, Idaho, and Nevada, with lesser amounts from Arizona, California, Colorado, Montana, Oregon, and Washington. The principal operating departments of the plant are weighing and sampling, Wedge roaster, D&L sintering, blast furnace and drossing, and baghouse. The lead bullion produced is shipped to a subsidiary, the U.S.S. Lead Refinery, Inc., at East Chicago, while the by-products, such as matte and speiss, are shipped to other smelters or re-treated at the plant.

Jan 1, 1948

By WM. HUFF WAGNER

Computations and allowances for mine depletion for Federal income tax purposes depend upon the meaning of certain terms in the pertinent provisions of section 114(b) 4 of the Internal Revenue Code. Unfortunately, but one of these terms is defined in the Code. Congress left it to the Commissioner to define the other terms in the Regulations. Even though the Commissioner, through his staff, labored long and earnestly to draft these definitions they have not been satisfactory to the mining industry, because the definitions in the Regulations and the interpretation placed thereon by the Commissioner do not state what the industry believes to be the clear and obvious intent of Congress. Consequently serious and prolonged disputes, unduly delaying the settlement of Federal tax returns involving percentage depletion deductions are continually arising between taxpayers and the Commissioner.

Jan 1, 1949

By Harold Vance

EMPLOYERS of engineers have not always been satisfied with the training that young graduates have received in the conventional four-year course. Specifically, employers of petroleum engineers for a number of years have believed that a four-year course does not allow sufficient time for the student to secure a fundamental engineering background plus the fundamentals of petroleum engineering. A group of California employers went so far as to set up a type of curriculum for a petroleum-engineering course, which was based on four years of undergraduate work and one year of graduate work, with most of the petroleum-engineering courses included in the graduate year.

Jan 1, 1944

By K. Huessener

INTRODUCTION THIS paper attempts a survey of the principles involved in the com¬bustion of blast-furnace gas in boilers and stoves. I do not expect to be able to give much information which is actually new, since the laws and methods of calculation pertaining to this problem are contained in a number of handbooks; but, so far as I am aware, they have nowhere been treated exclusively with reference to this one problem of gas economy. The road which I follow is less that of strictly scientific research than that of the practical engineer, faced by operation problems which require a. quick solution by easily accessible means without a prolonged search in scientific handbooks. For this purpose I give a number of tables and diagrams, as well as the results of many years' practical working experience as combustion engineer, which I trust will prove useful to my readers. HISTORICAL Considering the tremendous efforts made during the last 15 years to increase the efficiency of all kinds of power plants, it is highly surprising that until a comparatively very recent period, progress in the economical combustion of blast-furnace gas has been so slow. The explanation generally put forth, that fuel has been so cheap that it was hardly worth while to bother about this economy, will not hold good, for the greatest trouble was taken to improve the combustion of coal and to reduce the consumption of steam. The most plausible explanation appears to be the general impression, held as an accepted fact, that gas, especially hot, uncleaned, blast-furnace gas, was not a good boiler fuel. Many managers of high repute had tried unsuccessfully to improve the conditions of its use, and the dictum went forth that efficiencies of over 60 per cent., particularly with high loads, were impossible. This was the situation not only in the United States, with very cheap fuel, but also in Europe, where fuel prices are twice and three times as high.

Jan 2, 1916

By Betty J. Laswell, Gerald W. Laswell

Rotary drilling in modern open-pit mining is usually considered the lead phase which not only establishes the production rates but frequently limits them. From this viewpoint alone, the drilling phase must be maximized. The drill phase is the step that permits all the other operational phases to function within their design limits. This means that, in most cases, the drill is literally run to destruction to ensure that the shovel will be able to smoothly and consistently load a manageably size muck, the haul trucks can carry a balanced load without having a boulder dropped through the bed, and the crusher can devour constant rock size.

Jan 8, 1978

By P. R. Sahm, T. V. Pruss

Mixtures of fine GaSb and Gds as well as preal-loyed GaSbl,As, powders were hot-pressed at 690°C and 25,000 psi. Dense alloys with compositional gradients of less than 5 pct were obtained from mixtures containing about 20 mol pct GaAs. For x < 0.2, there were increasing compositional gradients, and for x > 0.2 a GaAs-rich second phase appeared in the microstructure. Densification as well as alloying wlechanisms were enhanced by dissociation and, possibly, oxidation reactions of the powders. Densification of coarse prealloyed material, however, primarily depended on plastic flow phenomena and required temperatures just below solidus and pressures of 50,000 psi Thermal and electrical properties were measured. Although in no case was the figure of merit of melt growth materials approached closer than to within 25 pct, the better overall thermoelectric properties were found in coarse-grained, prealloyed materzals which had been compacted to near theoretical density and where grain regrowth had been induced. Similar results are believed to hold in other binary 111-V compound systems if processed under similar conditions. The densification of unalloyed GaSb powders during pressure sintering (= hot pressing) was shown to depend strongly on powder particle size.&apos; Fine powders displayed a "liquid skin effect" that enhanced compaction through the presence of liquid gallium, whereas coarse powders compacted predominantly by plastic flow. The liquid skin effect, in particular, appeared attractive for alloying GaSb with other, higher-melting, III-V compounds, and to densify these in a one-step operation. This is of special interest in the case of III-V compound alloys as the conventional techniques of melt growth or long-time annealing of powders2 is very time-consuming, especially in cases where a large separation of liquidus and solidus can be expected, such as in GaSbl alloys.2 It was felt that experimentation with this system, a particularly unfavorable example, would allow us to extrapolate to several other, more favorable, cases. Uses of Ill-V alloys are most evident in thermoelectric energy conversion devices.&apos; For this reason certain thermal and electrical properties were measured and compared to those of melt-grown material and to hot-pressed prealloyed powders. EXPERIMENTAL PROCEDURE The pressure-sintering apparatus has been previously described.&apos; Using this equipment, both powder mixtures of GaSb with GaAs and prealloyed GaSbl-,As, powders were hot-pressed. The mixtures were pre- pared from cast GaSb and melt-grown GaAs. The prealloyed material was obtained from stoichiometric melts, initially heated to 1200°C in an evacuated quartz ampoule, and then annealed in the solidus-liquidus interval. A typical annealing cycle consisted of a heating to 850°C (1 hr), extended successive annealing at 750°C (65 hr), and slow stepwise cooling (25 hr) to below solidus. The GaSb, GaAs, and GaSbl-,As, materials were ground in a vibrational mill to particle sizes below 500 . A jet mill reduced these further where necessary. Fine powders were analyzed by Coulter counting for their size distribution. Average sizes by volume were calculated from the data. Mixing of the powders, where necessary, was carried out through rapid vibrational motion. The hot-pressing operation consisted of a degassing period of 15 hr, in most cases at 690°C, followed by several hours of compression, normally 25,000 psi at 690°C for powder mixtures and 50,000 psi at 710°C for prealloyed powders. The chemical compositions were confirmed by X-ray fluorescence analysis. To estimate the degree of solid solution achieved, lattice parameters were determined and interpreted according to Vegard&apos;s rule. In addition, optical microscopy helped to correlate the relative amounts of the phases present as well as the degree of porosity to the measured density. To reveal grain boundaries, polished surfaces were etched4 with H 2 O:H 2 O:HCl = 2:l:l. In several cases microscopic concentration gradients were monitored by electron-probe analysis-. RESULTS AND DISCUSSION Alloying and Densification of GaSn-GaAs Powder Mixtures. After preliminary experiments showed that no appreciable alloying took place in mixtures of coarse GaSb (22.5 p) and fine GaAs (2.5 p) powders, hot pressing of mixtures was confined to fine powders only (3.1 and 2.4 p, respectively). Alloying and densification apparently occurred simultaneously with a grain regrowth mechanism which depended on the presence of a liquid phase.&apos; The liquid phase was provided by the dissociation of GasbS particles into liquid gallium and antimony above 555°C. This not only enhanced grain regrowth and densification, as in unalloyed GaSb,&apos; but took on additional importance here for the alloying process. Alloying was speeded up by the resulting liquid-solid interaction as compared to the very slow solid-state diffusion process normally expected at these temperatures.&apos; The results obtained with a series of powder mixtures have been compiled in Table I. It is seen that for mixtures with less than 20 mol pct GaAs, x < 0.2, the compositional ranges increased and for x > 0.2 a GaAs-rich phase and free antimony appeared in the microstructure in sizable amounts.

Jan 1, 1968

By P. A. Farrar, M. D. Silver, K. L. Komarek

Thermodynamic properties of Hf-0 alloys have been determined from 0 to 25 at. pct 0 between 1000" and 1200°K by equilibrating specimens with alkaline metal oxide-metal vapor combinations. Partial molar-free energies, enthalpies, and entropies of oxygen have been obtained and are conzpared with similar results for the Ti-0 and ZY-0 In continuation of a thermodynamic investigation of the Ti-O and Zr-O systems1 activities of oxygen and lattice parameters of Hf-0 alloys have been deter- system. The positional entropy in all three systems corresponds to an ideal random interstitial solution with one interstitial site per one metal atom. The lattice parameters of hafnium and Hf-O solid solutions have been determined in the range 0 to 20 at. pct O from measurements of Debye powder patterns. mined. All three metals dissolve large quantities of oxygen to form interstitial solid solutions. The phase diagram of the Hf-O system is shown in Fig. 1.&apos; The maximum solubility of oxygen in the cph a phase is considerable (up to 25 at. pct O). The solubility in the high-temperature phase is much smaller. The only stable compound in the solid state is HfO2 which may exist with a certain oxygen deficiency. The low partial pressure of oxygen of Hf-0 alloys required the application of an indirect method. As the most suitable procedure a method, first applied by Kubaschewski to the V-O system,3 was combined with a principle developed by Herasymenko for the

Jan 1, 1963

By Paul F. Kerr

The insufficiencies of our mineral resources are becoming well known, and the national political conscience seems to be troubled at last by our dependence upon mineral commodities which must come from other lands. This realization places increased responsibility upon the industrial, educational, and governmental groups whose task it will be to solve the problems of mineral supply. As we all know, from the time that man first sought mineral deposits until recent years, prospectors have been largely responsible for mineral discoveries. Today the era of the prospector is almost over. The human ants that have literally examined all accessible outcrops and have tested the gravels of nearly all stream beds in the United States have left undiscovered few worthwhile mineral deposits within the scope of their recognition. The pages in the history of mineral exploration are now being turned from the era of the surface prospect to the era of the hidden de- posit.

Jan 1, 1949

By W. D. BRENNAN

FOR a considerable number of years past, there has been a shortage of experienced coal miners at the coal mine of the Phelps-Dodge Corp. This is probably due, to some extent, to the mines being so far south of the main western coal producing regions, so that experienced men secure employment before reaching this point. These mines are at Dawson, New Mexico, which is in Colfax County, near the Colorado line. The district is known as the Raton field, and the seam being worked is known as the Raton or Blossburg seam. The mines operated are Nos. 1 to 6, 8 and 9. The daily out- put at the present time, with restricted operations, is about 4000 tons, but the daily capacity is about 5500 tons. The mines are so grouped that the coal is dumped over four tipples. The mines are about twenty-five years old and extend as much as three miles under ground; they are all drift openings, with trolley, storage battery, and mule haulage. At the same time that the shortage of miners existed there was a surplus of common labor seeking employment. We learned that the Copper Queen. Branch of Phelps Dodge Corp. conducted a training school in one of its mines which had worked out very satisfactorily, and thus gained the idea of attempting such a school in the coal mines at Dawson.

Jan 1, 1929

By B. C. Allen

Grain boundary grooving has been studied in chromium, molybdenum, and tungsten under a variety of conditions using high vacuum techniques and tantalum -gettered argon. The average surface free energy of solid chromium, and the chromium-liquid silver interface free energy were respectively found to be 2200 ± 250 and 500 i 130 ergs per sq cm from groove formation kinetics and estimates of pertinent volume difffusion coefficients. The results for chromium were unffected by variations in interstitial content ranging from 0.003 to 0.09 pct C, or 0.003 to 0.03 pct O. Surface diffusion is the primary mechanism of groove formation in chromium under 1 atm argon at 1200" to 140O°C, and is essentially unaffected by 0.003 to 0.09 pct C, 0.003 to 0.03 pct O , metastable nitrogen contents up to -0.01 pct, and up to 2 torr Ag vapor. At higher temperatures, the major mechanism is volume diffusion in argon or evaporation-condensation in stutic vacuum. Surface diffusion occurs in molybdenum at 0.5 to 0.96 and in tungsten at 0.5 to 0.9 of the absolute melting tempera -ture by a single mechanism, possibly by the migration of single adatoms or vacancies. Results were slightly affected by up to 23 tory Sn vapor, and in molybdenum were essentially unaffected by 0.5 Ti or carbon in the range 0.002 to 0.02 pct. Volume difffusion through the liquid is the mechanism of groove formation in chromium-liquid silver at 1200" to 1400°C and in molybdenum-, Mo-0.5Ti-, and tungsten-liquid tin at 1200" to 2000°C. The solid-liquid interface free energies involved were estimated from grooving kanetics. WHEN a grain boundary intersects a solid surface, a groove tends to form along the line of intersection at temperatures above about half the absolute melting point (0.5 TM). The groove progressively grows by preferential atomic migration either by diffusion or evaporation. Establishment of a groove angle occurs in accordance with the grain boundary and surface free energies involved. The motivation for groove formation is a reduction in the total surface free energy of the system. This study is a continuation of previous work on thermal grooving of chromium, molybdenum, and tungsten.&apos; The temperature ranges were extended, and the effect of metallic and interstitial impurities was evaluated. The results were such that certain interface free energies and surface self-diffusion coefficients were deduced from the grooving kinetics. EXPERIMENTAL WORK Materials and Preparation. As indicated in Table I, the 0.05-0.08-cm-thick chromium, molybdenum, and tungsten sheet used was nominally 99.99 pct after recrystallization. Two lots of molybdenum with about the same analysis, Mo-0.5Ti,* and tungsten were ob- *Alloy compsitions are expressed in weight percent . tained commercially. Extruded chromium rod,&apos; prepared from iodide process crystals, was warm rolled to sheet at 700°C. Sheet of three Cr-0 impurity alloys containing up to 0.03 pct 0 was prepared by warm rolling arc melted, extruded, and swaged rod. Two Cr-C impurity alloys containing up to 0.09 pct C were made by equilibrating unalloyed chromium with a known amount of CH4 for 24 hr at 1150°C in previously evacuated quartz capsules. Chromium containing nominally 0.015 and 0.06 pct N was similarly prepared by equilibration with NH3. The sheet was recrystallized to give a stable grain size about equal to the sheet thickness. Molybdenum and Mo-O.5Ti were recrystallized in a tantalum resistance furnace 1 hr at 1 x lo-5 torr at 2300" and 220O°C, respectively. Tungsten was similarly annealed for 1 hr at 2500°C. Chromium and its impurity alloys were outgassed at 1100°C and recrystallized 1 hr at 1700°C under 1 atm Ar. Except for nitrogen, the impurity content stayed roughly constant. Nitrogen in both alloys was reduced to <0.001 pct. In fact, over 80 pct of the added nitrogen was lost after outgassing at llOO°C and annealing sheet 1 hr at 1300°C in argon in the presence of tantalum. Such a rapid loss can be rationalized since -2 torr N are required for equilibrium with 0.04 pct N in solution,3 while the equilibrium pressure is ~10-5 torr over tantalum at 1300°C.4 The recrystallized sheet was cut into small coupons which were metallographically ground and polished on one side with a minimum of grain boundary relief. The surface roughness was on the order of 0.01 µ. The tin and silver used were nominally 99.999 spec-trographically pure. After being outgassed at 1100°C and equilibrated in a molybdenum crucible for 0.5 hr at 1800°C in argon, the tin contained 3 ppm 0, <0.3 ppm N, and 0.1 ppm H. Following outgassing at 900°C and equilibration in a chromium crucible 1 hr at 1400°C in argon, the gas content of the silver was 1 ppm O, <0.5 ppm N, and 0.3 ppm H. Grooving Under Argon or Vacuum. All specimens were placed in unsealed containers made from rod or sheet of the same alloy, thereby enabling the polished surface to achieve gas-solid equilibrium. The annealing fixtures are shown in Fig. 1. The specimen was placed in a resistance furnace with a tantalum or Ta-10W heating element plus tantalum fixtures or radiation shields. Chromium was outgassed at 1100°C, and molybdenum and tungsten were outgassed at 1900°C to 1 x l0-5 torr or at the grooving temperature, whichever was lower. In vacuum anneals, the specimen was then heated directly to the intended grooving temperature. In argon anneals, 99.996 Ar was admitted

Jan 1, 1970

By K. E. Nelson

The effect of thorium and zinc variations on the strength and 100-hr creep characteristics of Mg-Th-Zn-Zr alloys was investigated. Optimum resistance to creep at 650° and 700°F are attainable within a certain range of thorium and zinc contents. This range does not conform to that which develops maximum tensile properties. RAPID advances have been made during the last few years in the development of magnesium alloys for elevated temperature applications demanding high resistance to creep. The beneficial effect of rare-earth metals on the creep resistance of magnesium alloys has been emphasized by a number of publications1-13 and such alloys are now in commercial production. The use of thorium as an alloying ingredient in magnesium was mentioned by McDonald and also in two Alien Property Custodian patent applications.10,17 The initial observation of Sauerwald that thorium contributes still higher creep resistance to magnesium than is attainable with rare-earth metals has recently been substantiated.&apos;" " In fact, it has been demonstrated that the useful temperature range of magnesium alloys is appreciably extended by the use of thorium. In all cases, it was observed that zirconium must be included in the alloys in order to render them fine grained and more readily castable. Several recent publications:2-27 indicate that a still further improvement in creep resistance and a further extension of the useful temperature range can be realized by the addition of zinc to alloys. The primary purpose of this paper is to present the results of a comprehensive study of the effect of zinc on the strength and creep characteristics of Mg-Th-Zr alloys. Compositions covering the range of thorium content from M to 6 pct and zinc content from 0 to 5 pct have been investigated. The creep characteristics at 650" and 700°F reported in this paper are based on results of tests of 100-hr duration. It is appreciated that creep tests of 100-hr duration might not yield adequate data for design purposes for parts with much longer expected life. However, for the purposes of the present discussion, it is felt that the combination of stresses and temperatures used in the 100-hr creep tests have yielded a clear representation of the compositional variation of creep resistance at the temperatures investigated. Creep tests of 1000-hr duration are now in progress on a few of the most promising alloys. Preparation and Testing of Alloys The alloys studied in this intensive investigation were prepared in 25 lb capacity mild steel crucibles. The thorium, zinc, and zirconium were alloyed and poured as described in earlier publications The thorium was introduced into the melt in the form of a Mg-Th hardener," the zinc added in the metallic form, and the zirconium alloyed in the form of the commercial hardener containing magnesium and 30 to 50 pct Zr.10, 26 Fluxing practices for melting and refining were the same as for magnesium-rare-earth metal-zirconium alloys. The melts were sampled for analytical determinations and poured into separately cast 1/2 in. diameter standard tensile bars. The test bars were given a precipitation treatment of 16 hr at 600°F in laboratory furnaces. It has been shown by other tests that a high temperature solution treatment followed by an aging treatment is unnecessary for the development of optimum properties in Mg-Th-Zn-Zr alloys. The selection of 600°F as the aging temperature was based on an attempt to achieve metallurgical stability without coalescence of the undissolved phases and the attendant loss in strength. The thorium, zinc, and zirconium contents of each melt were determined chemically. The zirconium contents are reported in two parts, "soluble" and "insoluble," referring, respectively, to the portions present in the alloy which are soluble and insoluble in dilute HCl acid. Distinction is being made between these two components of the zirconium content in the alloys because it has been found that only that portion of the zirconium content which is soluble in dilute inorganic acids affects the structure and properties of the alloys. The usual impurities consisting of copper, iron, manganese, and nickel were determined spectroscopically. The analysis for each melt is listed in Table I. A description of the methods of tension and creep testing has been detailed in earlier papers. The tests were performed with the cast skin re-

Jan 1, 1954

By J. A. Roberson, Robert A. Rapp

From the observation of platinum wire marker movement in the oxidation of columbium at high lemperatures and low oxygen pressures, predonzinant cation diffusion in CbO, has been demonstrated. The Cu,0 molecule was used as an oxidizing species to study the nature of the porous scale and the location of the reduction site in the oxidation of colum-bium. The Cb205 scale contains microporosity and forms by alternate ionic diffusional growth and fracture. The oxidation of columbium at high temperatures and very low po, results in a relatively compact and protective Cb205 layer. THE observation of marker movements during oxidation is one means for the identification of the mobile ionic species in an oxide lattice. Previous marker experiments in the oxidation of columbium have all resulted in the markers being found on the outside surface of the Cbz05 scale. The Cr203 powder markers of Klopp et a1.,&apos; the gold film marker of Kofstad and ~jijllesdal,&apos; and the platinum wire marker of Cathcart et a1 .3 were found at the oxide/gas interface for oxidation temperatures ranging from 450" to 120O0C. However, in all experiments relatively high oxygen pressures were used. As discussed by Mrowec, even the interpretation of marker experiments in simple scales containing only one compound is not without ambiguities. In brief, it can be said that a marker may be found almost anywhere in the scale layer if the metal oxidizes by cation diffusion through the scale; the position of the marker depends upon morphological happenings in the scale. When considering marker movement in a polyphase scale one must proceed with extreme caution. For example, in the past (and present) work markers have never been found at the columbium-scale interface, and one might infer that the oxygen ion is mobile in CbO and CbO,. However, only trace quantities of CbO and CbOz have been present on any of the specimens, so no firm statement is justified on this basis. Despite previous experimental work, considerable doubt still exists concerning the role of the oxides CbO and CbOz in the oxidation of columbium. The identification of the mobile ionic species in CbO and CbOz from the observation of platinum wire markers was one goal of the present investigation . The linear kinetics of columbium oxidation at high temperatures (T - 1000°C) suggests that the Cbz05 scales which form on columbium are porous. From mercury absorption measurements on a Cbz05 scale formed at 500"C, Aylmore et al.&apos; reported a minimum volume fraction of connected voids equal to 0.15. While these scales often appear to be quite porous when viewed in metallographic cross section, they are so brittle that metallographic preparation is likely to exaggerate any porosity originally present. In this investigation, porosity developed during the oxidation of pure columbium and present at the high temperature was detected by oxidizing specimens in sealed evacuated capsules containing large compacts of mixed copper and CuzO powders. wooda has demonstrated that the CuzO, or (CuzO),, molecule is volatile and that oxygen is transferred by the CuzO molecule from a Cu/CuzO mixture to materials having a greater affinity for oxygen. For each molecule of CuzO that is reduced at a sink for oxygen, two atoms of copper are deposited. Quantitatively, essentially all of the oxidation carried out by a Cu-Cu20 compact results from a displacement reaction involving the CuzO molecule. When a metal which oxidizes to form a porous scale is exposed to the CuzO vapor, the CUZO molecules are reduced in the pores leaving a deposit of metallic copper to mark the site of the reduction. This technique has the rather unique advantage that any copper-coated pores found in the scale are unambiguously related to the reduction site in the growth of the scale under consideration. Pores or cracks which form in a msition*- external to the reduction site or which occur as a result of cooling or handling of the specimen will not exhibit the copper deposit. EXPERIMENTAL PROCEDURE Marker experiments were made on columbium metal, and on pellets of CbO which had been pressed and sintered. Platinum wire markers (0.001 and

Jan 1, 1968

By L. H. Van Vlack, T. Y. Tien, R. J. Martin

The phase relationships of the MnTe-MnS system were studied by DTA procedures. There is an eutectic at 810°C with about 10 mole pct MnS-90 mole pct MnTe. An eutectoid occurs at about 710°C with approximately 7 mole pct MnS where the MnTe(NaCl) solid solution dissociates on cooling to MnTe(NiAs) and MnS. There is very little solid solubility of MnTe in MnS. ALTHOUGH MnS may exist in three different crystal forms,&apos; only the NaC1-type phase is stable.2 Above 1040°C, MnTe also has the cubic NaC1-type structure. Below that temperature, MnTe changes to the NiAs-type structure.3 This phase transition is rapid for both heating and cooling. As a result the high-temperature crystal form of MnTe cannot be retained at room temperature. Because MnO, MnS, and MnSe are all stable with the NaC1-type structure, and MnTe has this structure at high temperatures,4 solid solution formation could be expected among these compounds. It is interesting to note, however, that a complete series of solid solutions exist only in the MnS-MnSe system,&apos; and that the solid solution is quite limited in the MnO-MnS system.&apos; The MnSe-MnTe system possesses a complete series of solid solutions at high temperatures with separation at lower temperatures.7 Although ion size may be critical in the miscibility of MnO-MnS, it is quite possible that the bond type plays a more important role with the miscibility of MnSe-MnTe. This would permit us to speculate that the miscibility gap would be extensive in the MnTe-MnS system. EXPERIMENTAL Preparation. The samples were prepared by mixing and compacting MnTe and MnS powders. The MnS was previously prepared through the sulfur reduction of Mnso4.8 The MnTe had been prepared by mixing and compacting double vacuum distilled metallic manganese and high-purity tellurium in stoichiometric ratio modified with 1 wt pct excess tellurium. The compacted powders were put in a graphite crucible which was sealed in an evacuated vycor tube. The free space in the vycor tube was made minimal to reduce the loss of tellurium. The sealed assembly was then heated slowly to about 500° C where the free manganese and tellurium reacted vigorously, melting the MnTe which formed. Only one phase, MnTe, was detected by X-ray powder patterns and metallographic techniques. Each compact of MnTe-MnS was placed in a graphite crucible and then sealed in an evacuated vycor tube. The samples were heated at 1250°C for 4 hr and furnace-cooled. Microscopic examination revealed no third phase beyond MnS and MnTe. A typical microstructure is presented in Fig. 1. Identification. X-ray powder patterns were obtained using 114.6 mm Debye-Scherrer camera and Fe-Ka radiation. Mixtures of cubic MnS and hexagonal MnTe were observed in all of the compositions prepared. No lattice parameter change was noticed among different compositions, indicating no solid solution could be retained at room temperatures between these two end-members. A lattice parameter of 5.244Å for MnS was obtained by the Nelson and Riley9 extrapolation method using the diffraction lines of (h2 + k2 + 12) equal 12, 16, 20, and 24. The values, a = 4.145Å and c = 6.708Å, for hexagonal MnTe were obtained from the (006) and (220) lines in the back-reflection region. These values agree well with the values reported by Taylor and Kag1e.10 Differential Thermal Analysis. A differential thermal analysis procedure was used to determine phase relationships since the high-temperature equilibrium conditions could not be retained for examination at room temperature, even when the sealed samples (~0.5 g) were quenched in water. The samples were sealed in an evacuated 4 mm vycor tube with a recess in the bottom to accept a thermocouple. An Al2O3 reference was similarly prepared and the two placed within a piece of insulating fire brick to dampen spurious temperature changes within the furnace. The furnace was controlled by a mechanically driven rheostat which increased the temperature at a rate of about 15°C per min. Known phase changes in the Pb-Sn system1&apos; and the a-to-ß quartz inversion12 were used for calibration

Jan 1, 1969

By Paul M. Tyler

MILITARY power stems from industrial power and industrial power in turn depends predominantly upon an ample and assured supply of mineral raw materials. It thus becomes the duty of mineral economists to collate the vast array of data and logical deductions in order to reach an unemotional judgment as to the ability of the Soviet economy to withstand the strain of prolonged military action on the modern scale. Russian publications, reports: and official speeches have been laboriously screened and analyzed. Since these are the sources of information for the lower echelons of the Soviet industrial organization itself, they carry factual data that can be pieced together to show the present-day pattern. Apparent contradictions and obvious distortions or omissions can often be rationalized on the basis of observations made by foreign engineers and consultants during the 1930&apos;5 and by checking against the technical literature published before even so-called technical articles were riddled by bombastic and presumptuous claims.

Jan 6, 1951

By Alexander R. Troiano, Eugene P. Klier

Since the very early work on quenched structures, where the products of the martensite transformation had been recognizedl this transformation has provoked much interest and study. Theoretically it was desirable to account for the extreme changes in physical properties resulting from the formation of martensite, as that information might lead to results of practical importance. Desirable information, therefore, was on the kinetics of transformation from austenite to martensite as well as on the physical constitution of the martensite. It has been known for years that certain steels quenched to room temperature will contain persistent austenite as well as martensite. Other important and now well-established features of the martensite reaction are the Progress of the reaction on cooling only and the independence of Ar" with cooling velocities exceeding the critical velocity. These facts have been experimentally determined by various methods and investigators. Notable among the early investigators were Tammann and Scheill and Wever and Engel.2 Unfor- tunately, all investigators did not fully interpret their results, which, coupled with several investigations that yielde. conflicting resultsl caused a state of confusion that was not clarified until quite recently. X-ray investigations of martensite in steels3-6 indicate it to be a supersaturated solid solution of carbon in alpha iron. This supersaturation is evident from the appearance of a body-centered tetragonal structure with the addition of sufficient carbon. The dimensions of this tetragonal structure are a linear function of the carbon content within the limits of accuracy of the determinations. Slight tempering of tetragonal martensite leads to the destructi,, of the tetragonal structure, which is converted to a body-centered cubic strutture. This phenomenon has precipitated a controversy concerning the nature and mechanism of the tempering of martensite The facts in the case have been outlined by Epstein7 and more recently by Antia, Fletcher, and Cohen.8 The significance of Ar" on theoretical grounds is not clear, however, although considerable study has been devoted to its determination. The precise position of Art&apos; aS a function of carbon content was first stated by Greninger and Troiano9 for steels covering a range of approximately 0.7 to 1.8 per cent carbon. The effect of alloying elements on Ar" has recently been the subject matter of investigation by various methods.

Jan 1, 1945

By Walter Miller

ALTHOUGH confident of its ability to meet any demands which may be made, the petroleum refining industry is not complacent about the situation and realizes that the quantities of petroleum products to be furnished are so enormous and so far beyond what was previously estimated that the full co-operative effort of the industry must be exerted. Establishment by the President in May of the Office of Petroleum Coordinator for Defense with Secretary of the Interior Ickes at its head, plus the formation of the Petroleum Industry Council for Defense, in November, provide the channels for united endeavor within the industry and the means for gearing that endeavor within the industry and the means for gearing that endeavor in full harmony with the nation?s needs. Great strides have been made and a rapid understanding of the situation and the magnitude of the task is being attained by all concerned.

Jan 1, 1942

By J. L. Meijering

Oxidation hardening of cylindrical and spherical specimens first decreases with depth below the surface, but then increases again as the center is approached. This is in agreement with the view that this change in hardness is mainly determined by the change in velocity of the oxidation boundary, which affects the dispersion of the oxide. WHEN a thick slab of silver containing 0.3 pct Mg by weight is internally oxidized, the hardness measured on a cross section is found to decrease considerably with distance from the surface.&apos; This phenomenon has been attributed to the diminution of the velocity of the oxidation boundary. The smaller this velocity is, the more slowly the free-oxygen concentration rises towards the concentration in equilibrium with the oxygen gas. And a small 0 concentration favors dissociation and thus conglomeration of the oxide. For instance, the hardness decreases more rapidly during long annealings in nitrogen than in air.&apos; Measurements by Gregory and Smith3 on sections through internally oxidized Al-silver wire showed a smaller variation in hardness, probably because the wire diameter was only 0.9 mm. Wood4 found a drop in hardness with depth in internally oxidized Al-copper strip, and also—by electron microscopy—the concomitant increase in Al2O3 particle size. Under certain circumstances internal oxidation leads to formation of rather irregular inner oxide films in the midst of dispersed oxide. This special sort of conglomeration—discussed in Ref. 5—is also favored by greater depth below the surface.3,5 In this paper hardness measurements in large diameter cylindrical and spherical specimens are described. Here the oxidation velocity* goes through ness initially decreases with depth but increases again towards the center. Normally, the diffusion coefficient D1 of oxygen is very large compared to D2, that of the dissolved metal. If, furthermore, the atomic fraction c2 of the latter is much larger than the O-solubility cl- but c2D2 << c1D1- the velocities in question are easily calculated2 to be: for the cylinder and for the sphere. Here p is the radial coordinate of the oxidation boundary and R the specimen radius, which in dilute silver alloys is constant, as no external oxidation occurs. These equations have been derived for a divalent solute; for nondivalent solutes c2 has to be multiplied by half the valency. The equations are not valid near the center. For which can be considered as a standard case,2 the Eqs [I] and [2] begin to yield U-values which are appreciably too high for p/R = 0.05 and 0.15, respectively. But at the v-minima they are still very good approximations. These minima lie at p = emlR= 0.37R in the cylinder and p = 1/2 R in the sphere. Other factors besides the velocity v will also influence the hardness. The oxide concentration cox is constant in a flat strip, apart from a narrow region in the middle,2 but in cylindrical and spherical specimens cox decreases steadily with depth. When C1 << c2 and c1D1 >> c2D2 one can calculate

Jan 1, 1961

By D. K. Bose, C. K. Gupta, K. U. Nair

A new approach to processing an indigenously available low made molysulfide concentrate by chlorination with elemental chlorine in presence of oxygen is reported. Recovery of nickel and copper values associated with the sulfide concentrate by suitably treating the residue obtained after chlorination is also reported.

Jan 3, 1978

By Arnulf Muan, W. C. Hahn

Activities of "FeO" in "FeO"-MgO solid solutions have been determined in the temperature interval 1100" to 1300"C by equilibrating oxide samples with pure metallic iron in atmospheres of known oxygen partial pressures. The end members "FeO" and MgO form a complete solid solution series. The system shoztls a considerable positive deviation from Raoult&apos;s law. A large amount of data has been accumulated during the past 50 years on stability relations existing among various crystalline and liquid phases in oxide systems of importance in metallurgical processes. By comparison, very little is known about the thermodynamic properties within the various homogeneous phases present in the systems, particularly the crystalline phases. The present paper deals with determination of activities as a function of composition in solid solutions of wüstite ("FeO") and periclase (MgO). Such solid solutions ("Magnesiowustites") have simple sodium chloride structure and are known to be continuous between the end members at elevated temperatures (> 1000°C) and strongly reducing conditions such as prevail in contact with metallic iron. Wiistite has a defect structure in which the ratio of oxygen to iron varies and never has as low a value as 1:1 corresponding to the simplified formula FeO. Within the range of stability of this phase, the composition changes between a maximum oxygen content of approximately 25.6 wt pct (corresponding to the formula FeO.83O) and a minimum oxygen content of approximately 23.2 wt pct (corresponding to the formula Fe0-96O). The activity data to be reported in the present paper are based on using as standard state the wüstite which is in equilibrium with metallic iron at a particular temperature, i.e., "FeO" of minimum oxygen content at each temperature. For sake of simplicity, the formula FeO will be used to represent the wustite phase in the remainder of this paper. Consider the reaction 2 FeO solid solution = 2 Femeta1 + Ozgas in which FeO dissolved in another oxide dissociates to metal and gas. The activity of FeO in the solid solution, relative to "pure FeO" in equilibrium with metallic iron as a standard state, is then expressed as Here Po, and po2 * are the partial pressures of oxygen of the gas phase in equilibrium with metallic iron and the oxide solid solution or "pure FeO", respectively. The equation holds only if the metal phase is essentially pure Fe. The oxide combinations used in the present investigation fulfill this requirement. Magnesia is so much more stable than FeO that for all practical purposes aFe = 1 in the metal phase present in all mixtures used in this investigation. I. EXPERIMENTAL METHOD 1. General Procedure. The experimental method used was analogous to that developed by Foster and Welch1 and used recently by Hahn and Muan.2 It consisted of four steps: a) Determination of the equilibrium between FeO and Fe. b) Determination of d-spacing change with composition in oxide solid solutions (FeO-WO). c) Equilibration of various members of the solid solution series with a metal phase and a gas phase of known oxygen partial pressure. d) Determination of compositions of solid solutions resulting from step (c) by means of data obtained in step (b). 2. Starting Materials. General Aniline and Film Corp. carbonyl iron powder, type HP, was used as the source of metallic iron. A representative analysis was as follows: Fe, 99.6 pct; C, 0.01 to 0.04 pct; 0, 0.1 to 0.3 pct; N, 0.00 to 0.05 pct. Other elements were present as traces only. Wiistite was prepared from "Baker Analyzed" Reagent grade Fe2O3 of reported analysis as follows: Assay (Fe2O3), 98.8 pct; insoluble in HC1, 0.02 pct; not precipitated by NH,OH, 0.02 pct; Zn, 0.003 pct. Production of wüstite was achieved by a two-step

Jan 1, 1962