Search Documents

By E. A. Hopkin

Laboratory tests conducted by the author. together with actual field experience in Canada. have indicated the magnitudc of some of the factors affecting ability of drilling mud to clean the hole. A correlation was observed between funnel viscosity and particle slip velocity. A relationship was also observed between the Bingham yield value of the mud and the particle .slip velocity. Laburatury tests indicated little change in slip velocity with funnel viscosities up to ahout 80 sec/qt or to yield values of aboul 15 lb/100 .sq ft. The lip velocity of the partic1e.s. studied vuried from 160 ft/min with water to neerly zero for high mud viscositie. lncreasing the mud density, creating laminar annular mud flow or rotating the drill pipe Mlay also improve the carrying capacity of mud. Field tests indicated that during fast upper-hole drilling, the rate of cutting removal must he sufficien to maintain the concentration of cuttings in the annulus at less than 5 percent by volume to prevernt balled-up drill collars and .stuck drill pipe. INTRODUCTION In the Mid-Continent area, hole cleaning during rotary drilling normally involves the use of low-density drilling muds with funnel viscosities varying from 26 to 80 sec/qt. However, frequently it is necessary to raise the mud viscosity in excess of 200 sec/qt to clean the hole. In addition, field experience has indicated that during very fast upper-hole drilling, annular mud velocities considerably in excess of the maximum slip velocity of the cuttings (normally considered to be 120 to 150 ft/min) are necessary to prevent balling the bit and drill collars. In view of these variations in mud properties and circulation rates necessary to clean the wellbore, a study of factors affecting hole cleaning and the relative magnitude of each was undertaken. The study was also prompted by the knowledge that a drilling mud with properties close to those of water would drill at rates several times that of a viscous mud. The carrying capacity of these near-water muds was not clearly understood, however, and many drillers were reluctant to use them. DISCUSSION EFFECT OF MUD PROPERTIES ON DRILLING RATE The effect of mud properties on drilling rate has been studied by a number of investigators. 1t is clear from their work that mud properties close to those of water will significantly improve drilling rate and bit life. If the water-type mud will also effectively clean the hole and cause no logging or formation impairment problems, the choice of an appropriate drilling fluid is clear—use water. Often, however, a water-type drilling fluid is not capable of effectively cleaning the hole. THEORY OF PARTICLE SETTLING The forces acting on a particle that is allowed to settle through a fluid quickly reach equilibrium, and the particle settles at some constant velocity referred to as the slip velocity. The slip velocity of any particle depends upon a number of factors such as density and viscosity of the fluid, the volume, specific gravity, shape and roughness of the particle, and upon the shape and area of the projected face of the particle at right angles to the direction of relative fluid solid movement. Brown' expressed this relationship for spheres in Newtonian fluids in the following equation. where v, = slip velocity D, — diameter of sphere p, = density of spheye p, = density of liquid /a = friction factor g = constant. The friction factor f, varies as the size, shape, surface roughness and slip velocity of the body, and as the density and viscosity of the fluid varies. WaddelV ound experimentally that where dynamic similarity exists. f, was a function of the particle Reynolds number (NRe) of the sphere (Fig. 1). Fig. 1 shows that f, for spheres varies from over 10 for low NKe numbers to 0.44 for N,,. over 600.

THOSE MARKED THUS * ARE MEMBERS, MARKED THUS ?ARE ASSOCIATES. THESE SIGNS DOUBLED INDICATE LIFE MEMBERS AND ASSOCIATES RESPECTIVELY. THE FIGURES AT THE END OF THE ADDRESS INDICATE THE YEAR OF ELECTION. HEAVY-FACED TYPE SIGNIFIES HONORARY MEMBERSHIP. *AARONS, J. BOYD, Vivian Gold Mining Co., Ltd., Harris, West. Australia. '05 *ABADIE, EMILE R., Cons. and Min. Engr., 214 Union Savings Bank Bldg., Oakland, Cal. '76 ?ABBÉ, MAX F., Prest., Abbé Engineering Co, 220 Broadway, New York, N.Y. '07 ? ABBÉ, PAULO., Secy.,Abbé Engineering Co., 220 Broadway, New York, N.Y. '07 *ABBOTT, AI ARTHUR Morococlia, Peru, So. America. '95 *ABBOTT, CLARENCE Chief EDgr., Iron Mines, Dic Tennessee Caol, Iron & R. R. Co., Bessemer, Ala. '04 *ABBOTT, JAMES W., Min. Engr: Ploche, Lincoln Co., Nev. '94 *ABE, MASAYOSHI, Prof. of Mining, Imperial University Kyoto, Japan. '05 ? ACKER, E. O'C., Supt., Treatment Dept., Bethlehem Steel Co., So. Bethlehem, Pa. '86

Jan 1, 1910

By R. J. Lloyd

INTRODUCTION The Mount Isa Mine is a large modern underground mine located in North-Western Queensland, Australia. Two ore types are mined and treated separately. Currently silver-lead-zinc ore is mined at the rate of 2.6 million tonnes per annum and copper ore at the rate of 4.6 million tonnes per annum. The silver-lead-zinc orebodies are mined by sub level open stoping and cut and fill methods whilst all copper ore is extracted by various forms of sub level open stoping. The mining operations are highly mechanised and utilise diesel powered load-haul-dump units of various sizes, two and three boom face drilling jumbos, electric-hydraulic rotary-percussive ring drills, in-the-hole hammer drills, rotary blasthole drills, raiseborers, battery/trolley locomotives, a large fleet of rubber tyred service and supply vehicles plus light rockdrills mounted on airlegs, rail mounted overshot shovels and battery and diesel powered locomotives. All stoping production ore is extracted with diesel powered load-haul-dump units. The ore is tipped into orepasses which connect to the main rail haulage levels. On the haulage levels electric battery/trolley locomotives are used to pull rakes of bottom dump or side dump trucks which feed the ore into primary crushers. Following two stage crushing the ore is conveyed to the shaft and hoistod to surface in bottom dump skips. Each ore stream has its own rail transport system, crushing stations and hoisting shaft feeding separate concentrators. This paper will consider some aspects of the role of equipment and machinery in the growth of the mine, will discuss in some detail the machinery and equipment in use today and will conclude with a look at some possible developments in mining equipment for the future, with particular reference to the Mount Isa Mine. A summary of mining equipment in use at Mount Isa is given in the Appendix. THE PAST Silver-lead-zinc ore was discovered at Mount Isa in 1923 and within a very short time many small mines were being developed. However the rich surface ore traces did not continue and by 1928 Mount Isa Mines Limited had acquired sufficient leases to plan for a large scale mine to exploit the low grade orebodies. At this early stage it was recognised that the mine would need to adopt the most mechanised mining techniques then available in order to overcome its twin disadvantages of low graaes and extreme remoteness. The Company introduced bar mounted drifters and overshot shovels to replace hammer and tap and hand shovelling in development work and by 1930 headings were advancing at the rate of 30 metres per week. In keeping with the concept of mechanisation the early engineers designed the Man and Supply shaft with a very large, for those days, cage compartment measuring 3.8 m x 3.4 m. This shaft was the main means of access into the mine for 36 years until the K57 shaft (now R62 shaft) was commissioned in 1966. Man and Supply is still in regular use. Production commenced in 1931 at an annual rate of approximately 660 000 tonnes of silver-lead-zinc ore. The mine was mechanised to an extent which was previously unknown in Australia; whilst the concentrator, smelter and power house utilised the most modern and efficient equipment available. Even so, the mine was very near to closure on several occasions and did not return a dividend to its shareholders for many years. Production levels remained at or slightly below 660 000 tonnes until a separate copper ore streani and mill was commissioned in 1953, doubling the existing production levels. The first underground crushers were installed at this time. Production rates expanded in the years between 1953 and 1973. By 1960 production reached 2740 000 tonnes of ore. In 1965-66 total production was 3650 000 tonnes and in 1973 the production rate plateaued at the current level.

Jan 1, 1981

By M. E. Nicholson

IN order to understand how alloying elements influence hardenability through their effect on the rate of pearlite nucleation, it is advantageous to use a model to describe the mechanism of pearlite nucleation. The model which currently is most widely accepted has been described, among others, by Mehl et a1.1-3 and by Hultgren.4 Pearlite nucleation involves both the nucleation of ferrite and cementite.4,5 Cementite nucleates first, followed rapidly by the formation of ferrite at the cementite-austenite interface. The conclusion that cementite is the first phase to form during the process of pearlite nucleation is based, in part, on the observation that proeutectoid cementite is continuous with pearlitic cementite and that the orientation relationship between proeutectoid ferrite and austenite is not the same as that between pearlitic: ferrite and austenite.6,7 Recently, Smith" has suggested that the dissimilarity in orientation relations, instead of indicating the pearlite nucleation sequence, may be evidence that pearlite is nucleated in a grain adjacent to the one in which it is growing. Also, Modin9 as shown that ferrite in pearlite may be continuous with proeutectoid ferrite, and he has also shown that proeutectoid cementite is not always continuous with pearlitic cementite. Thus, it appears that the conclusion that cementite always initiates the pearlite nucleation process is open to serious question. The author believes that important evidence on the question of how pearlite is nucleated exists in the rates of pearlite nucleation of different steels. The following is a review and analysis of this evidence. If the nucleation of pearlite is considered as requiring the nucleation of both cementite and ferrite, then the time to nucleate pearlite consists of the time to nucleate the first phase to form, plus the time to nucleate the second phase at the advancing interface of the first. In the absence of a visible proeutectoid constituent, the second phase must be nucleated very soon after the first. If cementite is the first phase to form, the time to nucleate pearlite will be approximately equal to the time to nucleate cementite. Since the nucleation rate of a phase precipitating from solid solution increases with the degree of supersaturation, it would be expected that the rate of pearlite nucleation should increase with increasing carbon content. Digges10 has shown that the reverse is true. He determined the quenching velocity necessary to suppress pearlite formation in plain carbon steels as a function of carbon content. His results showed that pearlite formation could be suppressed with lower quenching velocities as the carbon content of the steel increased, at least up to 1.25 pct C, the highest carbon content he studied. Thus, it would appear that in plain carbon steels, in which pearlite is formed at the nose of the C-curve, the hypothesis that cementite nucleates first does not predict the observed change in nucleation rate. The validity of the current model of pearlite nucleation may be tested also by determining whether or not it predicts the relative influence of alloying elements on the nucleation of ferrite and pearlite. This can be done best by a consideration of the changes in a TTT diagram produced by a change in alloy content. Hultgren4 suggests that the general shape of a TTT diagram, as well as what constituents will form from austenite, can be predicted from the relative nucleation rates of ferrite and cementite. This is illustrated in the schematic diagram for a hypoeutectoid low alloy or plain carbon steel shown in Fig. 1. The C-curves for ferrite nucleation and for cementite nucleation are represented by AA' and CC', respectively, and the start of ferrite formation and pearlite formation are represented by AX and BC respectively. Adopting the current theory, Hultgren suggests that between X and C pearlite forms directly from austenite, since cementite nucleates more rapidly than ferrite in this temperature range. Conversely, at temperatures above Tx, ferrite is the first to nucleate and proeutectoid ferrite is formed. As proeutectoid ferrite grows, austenite becomes enriched in carbon, so that the cementite nucleation rate is increased. As a result, pearlite nucleation above temperature Tx is accelerated, beginning along BX and not along C'X. Temperature T, represents the temperature at which the nucleation rate of ferrite equals that of cementite. By extending this type of reasoning, using the principle that the nucleation rates of ferrite and cementite increase with increasing supersaturation of austenite with respect to these phases, it should be possible to predict the influence of carbon content on the shape of the isothermal transformation diagram. For a slightly higher carbon content than that of Fig. 1, the curve A A' representing the beginning of ferrite formation should be moved to the right, whereas the curve CC' representing the beginning of cementite formation should be moved to the left. For hypoeutectoid plain carbon and low alloy steels, this prediction does not agree with existing data. Instead, as the carbon content is increased, the pearlite curve moves to the right along with the ferrite curve and always appears to join it tangen-tially. This behavior is demonstrated by the TTT-curves of a series of manganese steels" shown in Fig. 2. In this figure, TTT-curves for four alloys containing 0.20, 0.40, 0.60, and 1.20 pct C are superimposed. The curves are identified in the figure legend. The letters F, P, and C are used to indicate the start of ferrite, pearlite, and cementite formation, respectively. In these steels, it appears that the nucleation of ferrite and of pearlite are related processes. As a result of the foregoing evidence, it is proposed that the formation of pearlite be considered as follows: Either ferrite or cementite may nucleate from austenite, then grow until the remaining phase is nucleated at the interface between the growing phase and austenite. (The growth of the first phase to form is assumed to be accompanied by a composition change in the adjoining austenite.) According to this model there are two modes of nucleating pearlite: 1—where cementite initiates the succession

Jan 1, 1955

By P. G. Shewmon, W. M. Robertson

The derivative of the surface tension with orientation, ??/??, for copper has been measured over the entire unit triangle. This derivative or torque term was determined from the variation of the dihedral angles at the intersection of twin boundaries and free surfaces. High-temperature anneals in graphite with a hydrogen atmosphere gave torque terms of 0.097 at (111), 0.066 at (100), and 0.0257 at (110). A variation from -36oto +23oC in the dew Point of the H2 had no effect on these values, nor did a change from 99.98 to 99.999 pct Pure copper. The removal of graphite from the system decreased ??/?? slightly. Considering the surface near a low-index plane to be smooth except for occasional steps, the free-energy increment per cm of step is calculated, and it is shown that the observed variation of ??/?? is consistent with a random distribution of steps and an interaction energy between steps. Integration of ??/?? gave the relative values of y at (100), (110), and (111) as comPared to ymax: (Y111/Ymax) =0.974, (Y110/Ymax) =0.996, (y100/Ymax) = 0.983. The ratio of the surface tension of coherent twin boundaries to the surface tension of the free surface was found to be (yT/ys) = 0.027 * 0.011. In a crystalline solid the surface tension y (surface free energy per unit area) depends on the orientation of the surface relative to the crystallographic axes of the crystal. Measurements of this variation of y with surface orientation have been reported for metals only within the last few years. Consider the grain boundary groove shown in Fig. 1. Here the three surfaces are all normal to the plane of the paper, and each has a different surface tension, y1, y2, and y3. If the system is at equilibrium, the total surface free energy must remain unchanged for a slight vertical displacement of the intersection (points A, B, and C are kept fixed). As shown by Herring,' the following equation is obtained:

Jan 1, 1962

By A. F. Lucas

The discovery of oil in 1901 on the Spindletop dome, Texas, inaugurated a new industry on the Gulf Coast, an industry which has gran with the discovery of successive fields, until today it engages the services of thousands of workers and employs enormous capital. New fields are being discovered from time to time and doubtless some still remain to be found, though of late years discoveries have become more infrequent. Nowadays several hundred dry holes are drilled each year in a fruitless and blind effort to discover new fields, for as yet geologic science has developed no effectual method of locating the coastal oil deposits in advance of drilling. Moreover despite the occasional discovery of new fields, the total production of the Gulf Coast is today no greater than it was in 1906, for the added production of the new fields has been offset by the rapid decline and more or less complete exhaustion of some of the older ones. Careful geologic work within the fields has in some cases increased the production temporarily, but has developed no really new supplies. The Gulf Coast oil industry seems to have passed its period of greatest expansion and to be declining at a fairly steady rate, and this condition is naturally viewed with alarm by the more farsighted operators. In my opinion, the time has come for the adoption of radical and aggressive methods of prospecting; and a fraction of the money wasted yearly in drilling shallow wells in hopeless locations might well be devoted to this purpose. Many facts lead me to believe that all the salt-dome oil has had a common origin; that it has migrated up from considerable depth along lines of structural weakness; and that a deep well, properly located, stands an excellent chance of discovering the parent reservoir and thus of developing new and probably great supplies. This paper is presented as a discussion—necessarily hypothetical and based largely on personal opinion—of the possibility of encountering deep-seated oil deposits beneath the salt domes. Salt-dome Structure All of the oil produced in the coastal region of Texas and Louisiana is probably associated with salt domes, though in Goose Creek, Edgerly, and one or two other fields no salt has yet been actually penetrated. As

Jan 1, 1920

Ahrenholz, Herman William, Jr., Student, Lehigh Univ Bethlehem, Pa. '35 Allen, Carl A., Student, Colorado School of Mines Golden, Colo. '35 Allen, Paul W., Student, Mass. Inst. of Tech Cambridge, Mass. '35 Allen, R. M., Jr., Student, Virginia Polytechnic Inst., "G" Co Blacasburg, Va. '35 Amberger, K. H., Student, Michigan College of Min. & Tech Houghton, Mich. '35 Andersen, Burton Lee, Student, School of Mines, Univ. of Washington Seattle, Wash. '35 Anderson, Joseph S., Student, Univ. of Texas El Paso, Tex. '35 Anderson, R. C., Student, Univ. of Washington Seattle, Wash. '35 Ansel, Gerhard 627 Clyde St., Pittsburgh, Pa. '34 Anutta, Frederick P., Student, Michigan College of Min. & Tech Houghton, Mich. '35 Apsouri, Constantin N., Graduate Student, Univ. of Arizona Tucson, Ariz. '35 Arakelian, Haig Mark, Student, Mass. Inst. of Tech Cambridge, Mass. '34 Archer, George K 1420 Court Pl., Denver, Colo. '34 Argall, George O., Jr., K. E. House Golden, Colo. '35 Argiielles, Alfredo, Student, Univ. of Texas El Paso, Tex. '35 Atwater, Ralph, Student, South Dakota School of Mines Rapid City, S. D. '35 Austin, Robert B., Miner, Page Mine, Federal Min. & Smelt. CoSpokane, Wash. '34

Jan 1, 1934

By Morris Cohen

STAFF: Editor, Gerhard Derge Acting Editor, Paul G. Shewmon Carnegie Institute of Technology Schenley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Karl L. Fetters, President; J.S. Smart, Jr., Past-President; R. C. Cole, Vice President; R. L. Hennebach, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: W. O. Phil-brook, Chairman; H. L. Bishop, R. C. Cole, J. N. Hobstetter, W. A. Krivsky, E. R. Morgan, F. C. Langenberg, R. E. Lund, Paul Queneau, L. L. Seigle, R. L. Smith, and T. V. Wainwright. Review and selection of manuscripts is under the supervision of the following Publicotions Committes: Extractive Metallurgy Division: R. E. Lund, Chairman; M. E. Wadsworth, Vice Chairman; D. H. Baker, Jr., G. M. Bell, R. E. Grace, W. A. Krivsky, R. A. Lewis, Charles O'Neill, A. W. Schlechten, R. E. Shinkoskey, and W. W. Stephens. Iran and Steel Division: T. V. Wainright, Choirman; H. L. Bishop, R. E. Boni, T. E. Dancy, D. W. Murphy, Johannes M. Uys, J. B. Wogstoff, and R. G. Ward. Institute of Metals Division: J. N. Hobstetter, Chairman; P. A. Beck, J. J. Becker, G. F. Bolling, J. 0. Brittain, J. B. Clark, R. S. Davis, A. E. Dwight, R. W. Fountain, L. R. Girifolco, J. C. Gurland, H. S. Kalish, E. L. Harmon, J. J. Heger, A. A. Hendrickson, L. Himmel, J. P. Hirth, H. H. Johnson, Jr., R. R. Nosh, T. N. Rhodin, R. H. Richman, H. C. Rogers, W. Rostoker, C. Sherby, C. W. Spencer, L. Slifkin, J. K. Stanley, R. Steinitz, H. C. Stumpf, and R. Swalin. Published bimonthly by the Americon Institute of Mining, Metallurgicol, and Petroleum Engineers, Inc., 345 East 47th Street, New York 17, N. Y. Telephone PLaza 2-6800. Subscription $30 peryear for non-AIME members in United States and North, South, and Centrol America; $32, foreign; $30per$7.50 for AlME members. Single copies, $6.00, single copies foreign, $6.50. The AlME is not responsible for any stotement made or opinion expressed in its publications ... Copyright 1962 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AlME New York . . . Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts . . . Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 224, Number 4.

Jan 1, 1962

By George W. Harris

In the earlier period of anthracite-mining, much coal was wasted, both underground and in the culm-banks on the surface. Such waste is common in the development of new mining-districts, in which, as a rule, only the richest material can be profitably treated. In the anthracite-region, special causes operated to increase this evil. The mines were generally worked under 20-year leases, and royalties were paid upon such coal only as was actually marketed. The lessees consequently cared for immediate profit solely. They were not bound to win all the coal they exposed, or to leave it in such condition that their successors could win it. Nor was it their interest or duty to educate consumers in the use of their product. The market called for coal of large sizes; and such coal they furnished, throwing away the rest. Any pains taken by them to bring about a more rational use of coal by their consumers would have borne fruit, after their leases had expired, to the benefit of somebody else. A full statement of the situation was given in 1893, in the report of the State Commission, appointed in 1889 to investigate the subject.' That body included the names of Heber S. Thompson, William Griffith and the late Eckley B. Coxe.2 Its report gives special attention to the utilization of the old culm-banks.

Jan 1, 1906

By E. T. Turkdogan, P. Grieveson

STAFF: Editor, Gerhard Derge Acting Editor, Paul G. Shewmon Carnegie lnstitute of Technology Sc hen ley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Karl L. Fetters, President; J.S. Smart, Jr., Past-President; R. C. Cole, Vice President; R. L. Hennebach, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: W. 0. Phil-brook, Chairman; H. L. Bishop, R. C. Cole, J. N. Hobstetter, W. A. Krivsky, E. R. Morgan, F. C. Langenberg, R. E. Lund, Paul Queneau, L. L. Seigle, R. L. Smith, and T. '4. Wainwright. Review and selection of manuscripts is under the supervision of the following Publications Committes: Extractive Metallurgy Division: R. E. Lund, Chatrmon; M. E. Wodsworth, Vice Chairman; D. H. Baker, Jr., G. M. Bell, R. E. Groce, W. A. Krivsky, R. A. Lewls, Charles O'Neill, A. W. Schlechten, R. E. Shinkoskey, and W. W. Stephens. Iron and Steel Division: T. V. Wainright, Choirman; H. L. Bishop, R. E. Boni, T. E. Dancy, C. W. Murphy, Johonnes M. Uys, J. B. Wagstaff, and R. G. Ward. lnstitute of Metols Division: J. N. Hobstetter, Chairman; P. A. Beck, J. J. Becker, G. F. Bolling, J. O. Brittain, J. 8. Clark, R. S. Davis, A. E. Dwight, R. W. Fountain, L. R. Girifalco, J. C. Gurland, H. S. Kclish, E. L. Harmon, J. J. Heger, A. A. Hendrickson, L. Himmel, J. P. Hirth, H. H. Johnson, Jr., R. R. Nosh, T. N. Rhodin, R. H. Richman, H. C. Rogers, W. Rostoker, C. Sherby, C. W. Spencer, L. Slifkin, J. K. Stanley, R. Steinitz, H. C. Stumpf, and R. Swolin. Published bimonthly by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc., 345 East 47th Street, New York 17. N. Y. Telephone PLaza 2-6800. Subscription $30 per year for non-AIME members in United States and North, South, and Central America; $32, foreign; $7.50 for AlME members. Single copies, $6.00, single copies foreign, $6.50. The AlME is not responsible for any statement made or opinion expressed in its publications ... Copyright 1962 by the American lnstitute of Mining, Metollurgical. and Petroleum Engineers. Inc. . . . Registered cable address, AlME New York . . . Indexed in Engineering Index, lndustriol Arts Index, and Chemical Abstracts . . . Second class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 224, Number 6.

Jan 1, 1962

By A. L., Bailey

All who are even generally aware of the tremendous rate of increase in coal washing operations must realize the growing importance of the float-and-sink test. I believe it is conservative to estimate that, in the past decade, the dollar volume of float-and-sink testing has increased tenfold. It is a simple matter of economy, then, to examine the factors that determine the cost of adequate float-and-sink testing. When the Coal Preparation Section of the Bureau of Mines entered upon a greatly expanded program of such work in connection with the synthetic liquid fuels investigations, it seemed advisable to examine these factors experimentally. The principal consideration that differentiates float-and-sink test sampling from general purpose sampling, is that the original particle size must be preserved. Therefore, the total cost of the test will be directly affected by any standard that might be proposed to limit sample bulk reduction at any given particle size. For this reason, the relationship of sample size to variability of results was the first factor to be studied experimentally.

Jan 1, 1949

By C. Y. Clayton, Francis B. Foley, Muir L. Frey

DuRing the past year, we have investigated the cause of 88 per cent, of the failures by breakage near the bit end of some 1-in. hollow, hexagon, drill steel used in a metal mine. This breakage in the region of the bit end of the steel was peculiarly interesting because we have been Ied to believe that breakage is most prevalent at the shank end of drill steels near the place where the steel is gripped in the chuck of the machine. Records from the mine showed, also, that the breakage was much more frequent in the short lengths of large gage than in the longer steels; this is shown graphically in Fig. 1. Because the shorter lengths of steels are usually those that have been made from broken pieces of long steels or from steels that have worn down in service, rarely being made from new stock, those who are wont to suspect steel of tiring and crystallizing in its old age through fatigue are quite apt to see in this instance an argument in favor of their idea. As usual, a careful examination of these steels reveals defects of a character hardly to be overlooked in favor of such a cause. The steel in question was rolled with a sand core and was of the usual drill steel composition: Carbon 0.85 per cent., manganese 0.60 per cent., silicon 0.25 per cent., phosphorus 0.02 per cent., and sulfur 0.02 per cent., with the exception that in some specimens there was vanadium, not exceeding 0.20 per cent. The following lengths and gages were used: LenGth, GaGe, LenGth. GaGe, Feet Inches feet Inches Starter 2 % 7 111/16 3 2 % 8 11 4 2 % 9 1 9/16 5 2 10 1 7/16 ________6_____________115/16____________________________

Jan 1, 1924

By Ed Van Eeckhout

As part of a U.S. Bureau of Mines-sponsored project on the utilization of "stiff" backfill to minimize potential rock burst hazards, a finite element study was undertaken to predict stresses and displacements around a stope mined up from the 5400 level of the Sunshine mine, Kellogg, Idaho. This stope was to be backfilled using a high-modulus fill. In preparation for that configuration, certain instrumentation was installed near the 5400 level to monitor stress changes. Due to untenable economics, only 2 cuts of the stope were ever made. This paper presents the results of the instrument readings taken during the first cut and compares them with the numerical predictions, as well as presents the modeling results of closure and fill stresses in the stope if it had been mined.

Jan 1, 1984

By P. W. George

THE rapid increase in cost of discovering new orebodies by churn drilling in the Tri-State district has led to some attempts to lessen the expense by using geophysical methods. Electrical prospecting was tried three or four years ago, but no successful results were recorded. In 1926, the Federal Mining and Smelting Co. engaged the North American Exploration Co., of Houston, Texas, to make some tests with the torsion, balance. At first, it was thought that the most favorable conditions for discovery of ore deposits with the torsion balance would be in locations where the ore was known to occur at rather shallow depths, FIG. 1.-CROSS-SECTION OF DUENWEG LEASE. therefore the first trial was made at Duenweg, east of Joplin, where some zinc ore had been developed at a depth of 130 ft. The gravity gradients at 61 stations on a tract of about seventeen acres indicated plainly one large zone of maximum gravity and a smaller narrow zone of minimum gravity. Fourteen churn-drill holes, half of which struck .ore, show that all the ore found was located outside the zones of maximum and minimum gravity. In the zone of maximum, gravity the limestone beds were closest to the surface, and the first chert beds encountered were at the greatest depth. The results (shown in Table 1) indicated that the gravity of the limestone was greater than the gravity of the fractured chert together with its orebodies, and probably also greater than the bouldery soil and clay on top of the limestone. A cross-section of the Duenweg lease is shown in Fig. 1.

Jan 1, 1928

By W. A. Nagel, R. P. Alger, H. Sherman, J. Tittmann

A sidewall epithermal neutron tool has been developed to substantially reduce environmental effects that have previously complicated neutron log interpretation. Designed for operation in uncased wells, the device provides increased accuracy in both liquid-filled and empty holes. A brief discussion of neutron moderation, diffusion and capture shows that logs using epithermal neutron detection depend on a smaller number of formation-characterizing parameters than those using thermal neutron or capture gamma ray detection. Thus, they come closer to providing an unambiguorls determination of hydrogen content. In this new device a directionally sensitive epithertnal neutron detection system has been incorporated in a side-wall source-detector skid to minimize borehole effects. The effects of variations in borehole size and shape, mud type, temperature and salinity are greatly reduced. Small residual borehole effects are then computationally accounted for in the surface control panel to provide a borehole-corrected neutron log. The log presents a direct recording of neutron-derived porosity on a linear scale. With corrections for borehole effects already applied, this direct recording of porosity simplifies log interpretation. Furthermore, comparison with a linear porosity presentation of a formation density log permits sandstones, limestones and dolomites to be readily identified. Thus, in complex or variable lithology, porosity is determined with greater accuracy and reliability than heretofore. Laboratory data and field results demonstrate the improvements in neutron logging afforded by this new side-wall epithermal neutron logging device. INTRODUCTION The new Sidewall Neutron Porosity (SNP) logging system, designed for use in uncased wells, provides reliability and accuracy never before achieved with neutron logs. The effects of variations in borehole diameter and shape, fluid salinity, mud weight and temperature—parameters that have long complicated neutron log interpretation— are suppressed or corrected for by this sidewall epithermal neutron detection system. Furthermore, to simplify interpretation the SNP log presents a direct recording of computed porosity on a linear scale. The performance improvements achieved by this new system arise primarily from the combination of two im- portant design features. First. though not unique to this new tool, an epithermal neutron detection system is used,',' Epithermal neutron detection substantially reduces the perturbing influences of the thermal neutron absorption properties of rock matrices and water salinity. Second, the neutron detection system is mounted in a directionally sensitive sidewall skid to greatly minimize borehole effects. The purpose of this paper is to explain briefy the advantages offered by the detection of epithermal neutrons, to describe the SNP equipment and the log, to present calibration and correction data and to give examples of interpretation methods made especially convenient by this new system. ADVANTAGES OF EPITHERMAL NEUTRON DETECTION Epithermal neutron detection, of all the neutron methods in current commercial use, provides the simplest determination of formation hydrogen content. Advantages of epithermal neutron detectors, as compared with thermal neutron and gamma ray detectors, are probably best explained by a brief review of the life of a source-emitted neutron. A fast neutron from the source will eventually be cap-tured by the nucleus of an atom. However. before capture is likely to occur, the fast neutron (energy of 100,000 electron volts (ev) or more) will be slowed down until it is in thermal equilibrium with its surroundings. The neutron is then considered to be a "thermal" neutron (average energy of 0.025 ev at 25C). The overwhelming majority of the slowing down thus occurs in reaching epithermal energies (energies just above thermal—0.5 to several ev). After reaching thermal energy. the neutron will "diffuse" through the formation with, on the average, no further energy change until capture. Upon the capture of the thermal neutron, relatively high energy gamma rays arc usually emitted. Hydrogen plays a very important role in the process of slowing down fast neutrons. On the other hand, the absorption effects of water salinity and low concentrations of other strong thermal neutron absorbers—relatively unimportant in the moderation process-—are very important in thermal diffusion, capture and the production of gamma rays. Thus, by detecting only epithermal neutrons with the SNP, spurious effects due to these thermal neutron absorbers are greatly minimized as compared to the effects on tools using thermal neutron or gamma ray detectors. The epithermal neutron detection system affords another important advantage. Log response in various litho-

Jan 1, 1967

New Jersey Zinc Co. - The Plants Canon City Palmerton Depue

Jan 12, 1953

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who called at Institute headquarters during the period Jan. 10, 1916 to Feb. 10, 1916: William Rettie, Yonkers, N. Y. Wallace E. Pratt, Manila, P. I. R. V. Norris, Wilkesbarre, Pa. T. Skewes Saunders, El Oro, Mex. Fred MacCoy, El Oro, Mex. M. L. Requa, San Francisco, Cal. Reno H. Sales, Butte, Mont. R. W. Schultz, Ravenna, O. R. T. White, Batourn, Russia. H. J. Brown, Chester, Pa. David T. Day, Washington, D: C. A. M. Van Rensselaer, New Rochelle, N. Y. H. M. LaFollette, LaFollette, Tenn. Norman C. Stines, Russia. F. N. Speller, Pittsburgh, Pa. Howard R. Hughes, Houston, Tex. Robert W. Hunt, Chicago, Ill. C. F. Schnepp, Ridgefield Park, N. J. B. E. Fernow, Toronto, Ont., Can. George L. A. Thomson, Elizabeth, N. J. A. F. Bennett, New York City. Jasper T. Robertson, Chicago, Ill. J. C. Ralston, Spokane, Wash. J. B. Tyrrell, Toronto, Ont., Can. George J. Lyon, Schenectady, N. Y. H. G. Officer, New York Cty. Jesse C. Porter is now superintendent of the San Fernando Mine, Hoyo de Manicaragua, Santa Clara Province, Cuba.

Jan 3, 1916

NEW MEMBERS The following list comprises the names of those persons who became members during the period Sept. 10, 1916, to Oct. 10, 1916. BLOOMFIELD, EDWIN CHARLES, Min. Engr., 1012 Standard Bank Bldg., Vancouver, B. C., Canada. BRINGS, HENRY, Min. and Met. Engr., Chief Engr., and Geol., Mollet-Mesrine, 1212 Mills Bldg., El Paso, Texas. CHASE, MARCH F., Vice-Pres., Commercial Acid Co., 1906 Boatmens Bank Bldg., St. Louis, Mo. CUMMINGS, ALVIN M., Asst. Mine Supt., Witherbee, Sherman & Co., Inc., Mineville, Essex Co., N. Y. DOUGLASS, GEORGE M., Genl. Safety Inspector, Amer. Smelt. & Ref. Co. 120 Broadway, New Fork, N. Y. EMRICH, CLARENCE T., Chief Chemist, Old Dominion Copper Min. & Smelt. Co., Box 1163, Globe, Ariz. GARDANIER, SUTTER ALBERT, Assayer, Mgr., Douglas Assay Co., Douglas, Cochise Co., Ariz.

Jan 10, 1916

By Robert Mehl

THE importance of the Widmanstätten structure to structure theory in metallography has been recognized by many writers.1 It is a structure produced by the precipitation of a new phase from a solid solution upon cooling as a result of changing solid solubility, and displays a characteristic appearance indicating a crystallographic relationship between the new phase and the original solid solution (Fig. 1). First discovered in 1808 by Alois de Widmanstätten2, the structure has been traced by analogy through many alloy systems. Particularly is this true of the steels. Sorby's classic work3 on the microstructure of iron and steel was in essence an attempt to explain the origin of this characteristic structure in meteoric iron. He observed in a Bessemer steel and in a cast-steel ingot structures which we now recognize as typical Widmanstätten figures.4 Osmond5 observed structures in a steel ingot analogous to those found in meteorites. Arnold and McWilliams6 obtained (and recognized) a

Jan 1, 1930

By A. W. Ashbrook

There are essentially three main classifications for extractants: acidic, basic, and neutral. The acidic and basic are also referred to as cationic and anionic, respectively. Some extractants are shown in Table 11-1. Acidic Extractants Acidic extractants which are of use, because of cost and/or insolubility in water, are alkylphosphoric, sulphonic, aliphatic monocarboxylic acids and naphthalene derivatives.

Jan 1, 1978