Search Documents

By Thomas P. Forbath

THE sudden realization that known sulphur reserves amenable to mining by the Frasch hot water process are nearing exhaustion focused attention on widely scattered surface deposits throughout the world. These deposits are not necessarily of lower sulphur content than ores located underneath Louisiana or Texas salt domes which usually average about 30 pct sulphur disseminated in limestone matrix. Their near surface occurrence, however, renders exploitation by the Frasch process impossible. As is well known, the Frasch process depends on the presence of 500 to 1000 ft of overburden and cap rock above the sulphur deposits to permit melting underground sulphur in place by diffusing hot water under pressures of 200 to 600 psig in the formation and raising the molten sulphur to surface by air lift. This process renders possible the production of pure sulphur which is 99.5 pct pure without any subsequent treatment. Surface deposits contain sulphur in the same range of concentrations as the salt dome deposits, i.e., from 10 to 50 pct sulphur, associated with various gangue materials such as silica, limestone, and gypsum. The pirincipal distinction, then, does not lie in the percentage of sulphur contained in the ore, but in the geological nature of the deposit. A recent study' of the world sulphur supply situation estimated 1950 sulphur production in the free world countries at 5.6 million long tons, of which the United States produced 5.2 million tons, or 93 pct of the total. While America's domestic needs alone would have been covered by national production, about 1.4 million tons were exported during the same year. Despite all the steps which are being taken to restrict use of elemental sulphur and to force the fullest possible development of alternate sulphur sources here and abroad, the deficit in elemental sulphur production will probably increase with time. As a result of intensive prospecting for oil throughout the Gulf Coast area discovery of significant new salt domes is held unlikely. With the growing scarcity of sulphur and what appears to be an inevitable rise in price, recovery from deposits not amenable to Frasch-process mining assumes greater economic importance. Untapped Reserves The most important deposits in this category are located in Sicily, where elemental sulphur occurs in Miocene limestone and gypsum formation. Sulphur content of these ores ranges from 12 to 50 pct with an estimated average of 26 pct. Although quantitative estimate of these reserves is not available it is held that they exceed 50 million tons of sulphur. Similar deposits occur also on the mainland which contribute about one-third of Italy's total current annual production of 230,000 tons, but these are known to be nearing exhaustion. Significant surface deposits of volcanic origin are located in South America, Japan and western United States, silica being characteristic gangue con-stituent. The largest of these deposits are in South America. More than 100 extend over a zone 3000 miles long, paralleling the west coast of South America. 'Total sulphur content of these deposits has been estimated to be as high as 100 million tons. The main islands of Japan also possess at least 40 known volcanic sulphur deposits with probable reserves of 25 to 50 million tons.' Prospected reserves in western United States might amount to 2 million long tons, principal deposits being located in the northwestern part of Wyoming, southern Utah, and eastern California. Volcanic deposits of lesser importance are found around the Mediterranean, in Turkey and Greece, and in Africa, Egypt, Abyssinia, and Somaliland. Beneficiation Methods Different methods of beneficiation have been used in these various locations. In Italy the Calcarone kiln and Gill regenerative furnaces are used exclusively. Both utilize heat liberated by burning part of the sulphur in the ore to liquify or vaporize the remaining sulphur, which is recovered by solidification or condensation. The Calcarone kiln is of conical shape, generally 35 ft in diam at base and 18 ft high. A kiln of 25,000 cu ft capacity burns for about two months and yields about 200 tons of sulphur. The Gill furnace consists of a series of chambers with domed roofs. Sulphur is burned and melted in one chamber at a time and the hot combustion gases are used to preheat the ore charge in the subsequent cell. These furnaces operate on a cycle of 4 to 8 days. The recovery yield of both systems is about 65 pct. Sulphur losses amount to 25 pct through the combustion to sulphur dioxide; about 10 pct is retained in discarded calcines. Ores containing less than 20 pct are not considered suitable as furnace feed. These methods are not only wasteful because of the low recovery obtained, but represent a serious atmospheric pollution problem. Sulphur produced ranges from 96 to 99 pct purity and thus does not match Texas or Louisiana sulphur. Owing to the present shortage, sulphur in the Middle East sells

Jan 1, 1954

Discussion of the paper of, RICHARD H. RICE, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 89, May, 1914, pp. 721 to 743. S. G. VALENTINE, Oxford, N. J.-In a paper read at the New York meeting of the Institute last February I presented some notes taken from our experience with the turbo blower operating on a blast furnace. In connection with Mr. Rice's very interesting paper there are a few items that might be of further practical interest. The question of the reliability of this type of blower will naturally be presented. In this connection we would say that our turbo blower has been in practically continuous use during the present blast, which was begun June 7, 1912, with only three interruptions for repairs of any consequence. Soon after blowing in there was developed a tendency of the blower to surge or pulsate. This occurred on operating at a point considerably below the normal capacity of the machine, and was checked with comparatively little trouble by throttling the intake slightly and taking up a small lost motion on the governor connections, a legacy of the previous blast that had not been attended to. All this required only a few hours' time. In. March, 1914, the furnace being banked on account of a blizzard that cut off our freight deliveries for five days, the opportunity was used to replace the carbon packing on the steam-turbine shaft and to repack the steam inlet valves. In June, 1914, the blower was off 8 hr. to replace an oil ring and scrape a bearing. With these exceptions we have made continuous use of the machine and find we can depend upon it with entire safety as a piece of machinery.

Jan 4, 1915

By Sherwin Kelly

IN presenting this brief historical perspective, it is not my purpose to address myself to the geophysicists, to most of whom the story is already well known. My objective is to draw the attention of those who hold the belief that geophysics is something new, typically twentieth century, to the fact that fundamentally, whether it was known by the name of geo-physics or not, the science is an ancient and an honorable one. It began many centuries ago, and our modern civilization and its commerce owe a great debt to its founders, who today are likely to he overlooked and their names forgotten. The word "geophysics" means the physics of the earth, and is descriptive of a science that in many ways bears the same relationship to geology that astrophysics does to astronomy. When dealing with dis-tant stars or deeply buried rocks, the experimenter cannot reach them to obtain samples, which can be taken to his laboratory for study. He therefore exhibits the resourcefulness of Mahomet in the mountain episode, and makes the terrestrial globe or the cosmic universe his labora-tory, studying the effects of distant bodies on certain "fields of force"" which come to him across interstellar space, or through the rocks that make our earth. The application of these techniques of the physics laboratory to the study of the stars is the science of astrophysics, and to the investigation of the earth is geophysics. Yet the origin of the most valuable contribution to the world's trade and commerce ever made by geophysics remains lost in deep obscurity. Unknown even is the country wherein lived the unsung genius who invented the first geophysical instrument, the mariner's compass! Worse yet, it is not certain whether this invaluable guide of man had its begin-nings in Europe or in Asia. A Chinese legend tells of the Emperor Hwang-ti, who attacked his enemy Tchi-yeou on the plains of Tchou-lou in the year 2634 B.C., whereupon the latter magically raised such a fog that the Emperor could not pursue the retreating troops. Not to be outdone, the mighty ruler constructed a chariot that indicated the cardi-

Jan 1, 1938

By Heinrich Ries

Fullers' earth is a clay-like substance, which has the property of decolorizing or clarifying oils. An ultimate chemical analysis shows it to differ from most ordinary clays in having usually a high percentage of combined water and a low amount of alumina. There is probably a large amount of hydrous silica present. Fullers' earth possesses little or no plasticity, and in order to work properly has to be ground very fine. A chemical analysis is of little value at present in determining its quality; only a practical test suffices. Up to about two years ago all of the fullers' earth used in this country was imported from England; but about that time deposits were discovered in Florida, "† and since then rumors of its occurrence have been coming from all parts of the country. Next to the Florida deposits of fullers' earth, those of South Dakota are the most extensive thus far discovered in this country. The earth was first discovered near Fairburn, Custer county, and other deposits have since been prospected at Argyle, Minnekahta and other localities. Fairburn.—One of the first deposits located and opened up is five miles southeast of Fairburn, Custer county. The mine is a mile from the Fremont, Elkhorn and Missouri Valley Railroad, and the section exposed shows, beginning at the top: Feet. Micaceous sandy clay,......... 6 Fullers' earth,..........9 Micaceous sandstone,......... The fullers' earth passes upwards into the sandy clay, but in its purer portions it is a yellowish, gritty clay, with a somewhat

Jan 1, 1898

By Richard Hamburger

(1) Introduction: The purpose of this paper is to call attention to certain methods which will shorten and simplify the calculation of plane tri-angulation. These methods, though not new,',2 do not appear to have been properly publicized in the United States. The cotangent (or tangent) solution of a triangle permits calculation of coordinates in a smooth series of operations of the calculating machine with a minimum of notation. The semigraphical solution permits the simultaneous solution of a number of intersections, at one station, without the added burden of solving additional triangles. This in turn encourages more numerous field checks and more complete office computation than would normally be undertaken. RICHARD HAMBURGER, Junior Member AIME, is Junior Engineer, Inspiration Consolidated Copper Co., Inspiration, Arizona. TP 2798 A. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Tables I and I1 show the distinct advantage which the combined use of the cotangent and the semi-graphical solutions hold over, what might well be called, the standard solution. It will be shown that the positions for the entire net in fig. 1 may be calculated without computing any distances, thus saving much computation. (2) Comparison of Cotangent and Standard Solutions: To compare the cotangent method with the standard method, the notation involved in the solution of triangle 1-X-4, fig. 1, by both methods is shown. Fig. 2 shows the given information, that is, the coordinates and azimuths of Stations 1 and 4, and angles of the triangle or the azimuths from Stations 1 and 4 to Station X. (Azimuths are used here because the author feels that they are easier to handle, but bearings may be used by those who prefer them). It will be seen from the above comparison that the advantages of the cotangent solution of a triangle are: (a) rapidity, (b) full use of the calculating machine, (c) the small number of

Jan 1, 1951

The Institute assembled in the library of the Sheffield Scientific School at 8 o'clock, Tuesday evening, February 23d. Prof. G. J. Brush greeted the members present on behalf of the Government of the Sheffield School in a few words of cordial welcome, to which President Raymond responded. Dr. Raymond then delivered an address on the History of the Relative Values of Gold and Silver. The Council presented, through the President, a list of names of persons duly proposed for members and associates, with recommendation for election. The following gentlemen were unanimously elected: *Prof. George J. Brush,. .. New Haven, Conn. *Prof. Oscar D. Allen,. .. New Haven, Conn. *C. Constable,.....New York City. *Leven S Goodrich,.... Oxmoor, Jefferson Co., Ala. *Charles J. Nourse,.... Columbia, Lancaster Co., Pa. *J. W. Mickley,.....Hockendauqua, Pa. *Hugh Alex. Crawford,. ..St. Louis, No. *General Ario Pardee,. .. Hazleton, Luzerne Co., Pa. N. W. Lord,.....New Pork City. J. Holme Maghee,.... New York City. *George E. B. Jackson,. .. Portland, Me. *Charles W. Watkis,.... Salt Lake City, Utah. *Charles E. Hall,....Philadelphia. *Charles J. Duval,.... San Francisco, Cal. Joseph Gorlinski,.... Salt Lake City, Utah. * Alfred Wartenweiler,. .. Salt Lake City, Utah. Wilmot J. Bowen,.... Salt Lake City, Utah. *Joseph Stokes,..... Trenton, N. J. Jason P. Brown,.... Boston, Mass. *William Davis Hartshorne,. . Bethlehem, Hunterdon Co., N. J. *Henry Williams,.... Spanish Bar, Clear Creek Co., Cot. *Robert Forsyth ,....Chicago, Ill. *S. T. Wellman,.....Cleveland, Ohio. *H. C. Walton,.....Chicago, 111. *Andrew Roy,.....Columbus, Ohio. *James H. Rittenhonse,. .. Providence, Pa.

THE Institute assembled in the library of the Sheffield Scientific School at 8 o'clock, Tuesday evening, February 23d. Prof. G. J. Brush greeted the members present on behalf of the Government of the Sheffield School in a few words of cordial welcome, to which President Raymond responded. Dr. Raymond then delivered an address on the History of the Relative Values of Gold and Silver. The Council presented, through the President, a list of names of persons duly proposed for members and associates, with recom¬mendation for election. The following gentlemen were unanimously elected: *Prof. George J. Brush, - New Haven, Conn. *Prof. Oscar D. Allen, - New Haven, Conn. *C. Constable, - New York City. *Leven S Goodrich, - Oxmoor, Jefferson Co., Ala. *Charles J. Nourse, - Columbia, Lancaster Co., Pa. *J. W. Mickley, - Hockendauqua, Pa. *Hugh Alex. Crawford, - St. Louis, Mo. *General Ario Pardee, - Hazleton, Luzerne Co., Pa. †N. W. Lord, - New York City. †J. Holme Maghee, - New York City. *George E. B. Jackson, - Portland, Me. *Charles W. Watkis, - Salt Lake City, Utah. *Charles E. Hall, - Philadelphia. *Charles J. Duval, - San Francisco, Cal. †tJoseph Gorlinski, - Salt Lake City, Utah. *Alfred Wartenweiler, - Salt Lake City, Utah. †Wilmot J. Bowen, - Salt Lake City, Utah. *Joseph Stokes, - Trenton, N. J. †Jason P. Brown, - Boston, Mass. *William Davis Hartshorne, - Bethlehem, Hunterdon Co., N. J. *Henry Williams, - Spanish Bar, Clear Creek Co., Col.. *Robert Forsyth, - Chicago, Ill. *S. T. Wellman, - Cleveland, Ohio. *H. C. Walton, - Chicago, Ill. *Andrew Roy, - Columbus, Ohio. *James H. Rittenhouse, - Providence, Pa. * Members. † Associates

Jan 1, 1875

By C. F. Wang

Page I. Introduction............:.............. 395 Manchuria in General ....................... 395 Pen-hsi-hu............................ 397 Pen-hsi-hu Coal & Iron Co., Ltd................... 399 I1. organization........................... 400 III. Coal Deposit........................... 402 Location..............................402 Geology............................. 403 Coal Mining...........'.................. 404 Mining Methods........................407 Mining Cost.........................408 IV. Coal Washing Plant.......................408 V. Coking Plant..........................410 VI. Iron Deposit...........................413 Magnetite Belt.......................... 413 Origin of Deposit......................... 414 Iron Mining........................... 415 VII. Concentration Plant........................ 417 VIII. Briquetting Plant.......................... 418 IX. Blast-furnace Smelting...................... 418 iNTKODtrCTION Manchuria in General Manchuria. called the "Three Eastern Provinces" in Chinese. forms the northeastern corner of China and is bordered by Siberia on the north and northeast. and by Korea on the east. It is a land famous in Chinese annals as the place of origin of the Ching dynasty. and in more recent times it has bcen an arena for diplomatic maneuvering and commercial competition between the Russians. advancing from the north. and the Japanese from the southeast. It derives its name of "three eastern provinces" from the fact that it is divided into three provinces; Hei-

Jan 1, 1918

By Robert A. Cook

In the increasing struggle to cheapen the cost of our iron and steel products a great deal of attention lias been given to economies in the manufacture of coke; and while but little lias been accomplished in this direction in the United States, the narrow margin between cost and market-price, which has obtained here for the past few years of continuing manufactur ing depression, has brought the coke-maker face to face with the problem, how to save, and benefit by it, the hitherto waste products of distillation. I These may be summed up under three heads, generally rank ing, in value, in the following order: 1. Ammonia salts.. 2. Oil- or tar-products. 3. Gas. There are cases in which the last may assume the position of greatest importance. The greatest obstacle encountered by the American coke maker, on investigating the subject, has been the apparent necessity of discarding his existing plant of bee-hive ovens, and erecting an entirely new and very expensive system of retort ovens, against the product of which Be has probably been prejudiced from his earliest knowledge of the subject. The object of this paper is to bring prominently before our coke-experts a brief history of the development at Sheffield, England, of a most successful system of the utilization of by products in connection with all already existing plant of bee hive ovens. This system has now been in satisfactory operation for about five years, and is applied to a series of blocks of ovens, comprising-about 140- in all At this plant, belonging to the well-known firm of Newton,

Jan 1, 1897

By R. W. Raymond

There is apparently no end to the doubts, inconsistencies and absurdities in which the courts of our mining States and Territories are involved in their attempts to apply to conditions of ever-increasing complexity the provisions of our anomalous mining law. In previous papers, I have called this statute " the law of the apex," because it based upon that vague, novel and mysterious condition the most important grant of title. But the apex is scarcely a more essential feature than the end-lines and the side-lines; for the rights which it may confer may be limited in various ways by these; so that we have, in many a case, the most ridiculous result that the United States, in return for the money of a citizen, conveys to him with much solemnity, under its broad seal, nobody knows what, bounded nobody can tell how. A decision recently made at Butte by Judge De Wolfe, of the United States District Court of Montana, in the case of King et al. vs. The Amy and Silversmith Mining Company, furnishes a fresh illustration of this criticism. The diagram on the following page, constructed without precise regard to courses and distances, simply to assist in the statement of the essential features of the case, will, 1 hope, make clear the principles . involved : The plaintiff occupies a location (the Nonconsolidated) adjoining on the north the defendant's location, a b c d (the Amy), and the disputed mining-ground lies, let us say, in depth under the point W, that is, on the dip of the vein, VD, but not under the surfacelocation, a b c d. The defendant has the prior title, and claims this ground under its extra-lateral right. It is admitted that the apex does not cross the end-line, a d, and does cross the side-line, a b. Whether it crosses, at the other end of the location, the end-line, b c

Jan 1, 1889

By J. H. Pratt

In a recent paper* on the origin of corundum associated with the peridotites of North Carolina, attention was called to the constant occurrence of the mineral, chromite, in these rocks. The field-data obtained during the preparation of that paper have been used largely in the present paper. During the past summer the general occurrences of chromite have been carefully studied, and those in North Carolina have been especially examined in the field. It is purposed to give, in this paper, the reasons why the chromite should be regarded as having been formed at the same time with the peridotites, having been held in solution by the molten mass of the peridotite, and crystallizing out among the first minerals as the mass began to cool. This theory is essentially the same as that advanced by me for the origin of the corundum associated with the peridotite rocks, and a similar line of reasoning has been used to substantiate the theory proposed. Investigations concerning the igneous origin of some of the ores have been materially aided, during recent years, by the skillful experiments of Morozewicz and Lagorio,§ and by researches that show us, more clearly, why we should regard a fused mass of rock as a liquid, having similar properties to an ordinary solution. These experiments have shown that a molten basic glass, similar in composition to the basic magnesian rocks, dissolves alumina readily, and that upon cooling, the first minerals to separate out are corundum and spinel.

Jan 1, 1900

By W. R. Hibbard

IN ref. 1, on the basis of tension and torsion experiments with single crystals of a brass, the values given in Table I were obtained for elastic coefficients. It was pointed out by Zener that the values for the 71.2 pct Cu were not satisfactory, since they resulted in a negative value for the bulk modulus, namely —4.17X1012 sq cm per dyne. In reevaluating the data of this investigation, it was determined that the reason for this negative bulk modulus lay in the extrapolation of the reciprocal Young's modulus to the zero value of the orientation function shown in Fig. 5 of ref. 1. This extrapolation was reevaluated by the method of least squares (50 pct probability) and a new value of the coefficient S,, was determined as 18.9220.42X 10M sq cm per dyne in lieu of the value originally reported of 18.82x10 sq cm per dyne. This new value of S, leads to a new value of S, of — 9.43 X101" sq cm per dyne. The values of the other coefficients are unchanged. results. This value compares with the value of 12.3X10 sq cm per dyne reported by Schmid and Boas? The new results are summarized in Table 11. These results follow similar qualitative trends, previously published,' relative to the effect of zinc content. However, the derived values of C11, C,, C,, and K are so sensitive to the uncertainty in the first decimal place of the S, values that they are probably not useful. This uncertainty must also apply to the previous results of Masima and Sachs," who obtained S, values from a similar extrapolation drawn wholly above their data points. Acknowledgments Advice and assistance on the statistical methods were obtained from R. W. Guard. The calculations were carried out by Miss E. Saacke.

Jan 1, 1958

By Raja V. Ramani, Ralph W. Barbaro

This paper presents an application of a Mixed Integer Programming (MIP) model to the problem of locating a centralized coal preparation plant and determining the production schedule for the mines. The system used for illustrating model application is hypothetical but realistic. It consists of three mines, two potential preparation plant sites, heavy media processing plant, and one market. The goal is to maximize the total profit of the system while satisfying the coal delivery schedule over a three year period meeting both quantity and quality requirements (ash, sulfur, and heat content). In addition to the base case, four different scenarios are analyzed. These four modifications are: (1) removing the flotation circuit from the preparation plant and sending all of the fines directly to the clean coal, (2) lowering the quality of coal from one of the mines, (3) applying discounts to the unselected site to improve its competitive position, and (4) adding a new mine. A detailed discussion of the base case and the effect of these four alternatives is presented.

Jan 1, 1983

By Paul M. Tyler

Higher freight rates and better methods of beneficiation now may make it more economical to open inferior deposits closer to a glass factory than to work higher-grade deposits farther away. Nature of impurities and special treatments as well as common practice of sulphuric acid leaching are described. HISTORICAL concepts of the economics of the glass-sand industry are changing rapidly. The greatly expanded demand for glass containers combined with higher freight rates on raw materials and manufactured products have induced a migration of glass factories toward densely populated centers and the creation of new standards of place value for substandard sand deposits. This migration has been facilitated by the construction of pipelines to bring cheaper natural gas and liquid fuel to large cities and may be further speeded by the adoption of modern mineral dressing methods to permit economical utilization of local raw materials. Our national resources of naturally high-grade silica sand are abundant, but most of the best deposits are situated so far from large centers of population that it now costs $3.00 to $5.00 a ton to carry the sand from the mine to the optimum site for a factory making beverage bottles, scientific and electrical glassware, and miscellaneous blown and pressed ware for local markets. It follows that on the basis of freight savings alone it may be economical to use material from inferior deposits closer to the factory even though the f.O.b. cost of mining and treatment may be much higher than at a higher grade deposit farther away. Particle-size distribution is a feature of glass-sand specifications. As long as glassmakers insisted upon having their sand principally coarser than 100-mesh, any material was automatically excluded from consideration that could not be purified without fine grinding or other drastic treatment which greatly reduces the size of the quartz grains. However, re- cent large-scale tests in Norway' showed that finely-crushed quartz used in a soda-lime-silica glass batch caused it to melt and become refined appreciably faster than when ordinary coarse (Belgian) sand was employed. Dust losses were negligible. Since the pre-war cost of sand was only 3 pct of the manufacturing cost of the glass, it was deemed economical to pay twice as much for crushed quartz because of the saving in wear and tear on the furnace walls. In the author's unverified opinion, sand ranging in size between 150 and 400-mesh would probably be superior to that in the more usual range of 20 to 100-mesh. Former objections to fine sand (other than dust) were doubtless fostered by the natural concentration of impurities in the finer sizes. Ordinarily the most objectionable, as well as the commonest, impurity from the standpoint of the manufacturer of any but the cheaper qualities of colored glass is iron. No natural sands are really pure silica. Even water-clear quartz crystals are likely to contain impurities in the form of solid solution as well as inclusions which cannot be eliminated except by chemical treatment that will break down the silica lattice. Pure white pegmatite quartz will usually analyze 0.01 pct or more of iron oxide, and ordinary vein quartz and the quartz grains in most

Jan 1, 1951

By Paul M. Tyler

Higher freight rates and better methods of beneficiation now may make it more economical to open inferior deposits closer to a glass factory than to work higher-grade deposits farther away. Nature of impurities and special treatments as well as common practice of sulphuric acid leaching are described. HISTORICAL concepts of the economics of the glass-sand industry are changing rapidly. The greatly expanded demand for glass containers combined with higher freight rates on raw materials and manufactured products have induced a migration of glass factories toward densely populated centers and the creation of new standards of place value for substandard sand deposits. This migration has been facilitated by the construction of pipelines to bring cheaper natural gas and liquid fuel to large cities and may be further speeded by the adoption of modern mineral dressing methods to permit economical utilization of local raw materials. Our national resources of naturally high-grade silica sand are abundant, but most of the best deposits are situated so far from large centers of population that it now costs $3.00 to $5.00 a ton to carry the sand from the mine to the optimum site for a factory making beverage bottles, scientific and electrical glassware, and miscellaneous blown and pressed ware for local markets. It follows that on the basis of freight savings alone it may be economical to use material from inferior deposits closer to the factory even though the f.O.b. cost of mining and treatment may be much higher than at a higher grade deposit farther away. Particle-size distribution is a feature of glass-sand specifications. As long as glassmakers insisted upon having their sand principally coarser than 100-mesh, any material was automatically excluded from consideration that could not be purified without fine grinding or other drastic treatment which greatly reduces the size of the quartz grains. However, re- cent large-scale tests in Norway' showed that finely-crushed quartz used in a soda-lime-silica glass batch caused it to melt and become refined appreciably faster than when ordinary coarse (Belgian) sand was employed. Dust losses were negligible. Since the pre-war cost of sand was only 3 pct of the manufacturing cost of the glass, it was deemed economical to pay twice as much for crushed quartz because of the saving in wear and tear on the furnace walls. In the author's unverified opinion, sand ranging in size between 150 and 400-mesh would probably be superior to that in the more usual range of 20 to 100-mesh. Former objections to fine sand (other than dust) were doubtless fostered by the natural concentration of impurities in the finer sizes. Ordinarily the most objectionable, as well as the commonest, impurity from the standpoint of the manufacturer of any but the cheaper qualities of colored glass is iron. No natural sands are really pure silica. Even water-clear quartz crystals are likely to contain impurities in the form of solid solution as well as inclusions which cannot be eliminated except by chemical treatment that will break down the silica lattice. Pure white pegmatite quartz will usually analyze 0.01 pct or more of iron oxide, and ordinary vein quartz and the quartz grains in most

Jan 1, 1951

By J. E. Hove

The high temperature physical properties of graphite are reviewed and interpreted in the light of present day knowledge of the mechanisms affecting these properties. The thermal and mechanical behaviors only are discussed and, whenever possible, comparisons are made with other refractory materials. Possible further studies are indicated, including some carbide work. AS long as the term high temperature implied only temperatures up to about 1000°C, the materials problems which arose could usually be handled by fairly conventional metal alloy types, such as the Co-Cr-Ni superalloys, for which there exists a great deal of technology. Perhaps this temperature can still be considered an upper limit for normal applications, but it is certainly true that the number of abnormal applications is increasing rapidly. The advent, in recent years, of ram-jet and rocket missiles and of high power nuclear reactor heat sources has raised a host of questions concerning the basic problem of what material to use in the temperature range up to 2000°C and higher. While there are, of course, many metals, in the second and third transition series, which melt at considerably higher temperatures than this, these metals are, at present, pretty well excluded from practical use by other considerations, such as re-crystallization, chemical activity, or excessive plastic deformation. The behavior of metals, from the standpoint of dislocation theory, is just beginning to be understood and thus there is some hope for the future development of very high temperature metals, but the immediate problems would most logically appear to have solutions involving the nonmetals, such as the refractory ceramics and graphite. For this reason, there is presently a great deal of engineering and experimental research being performed on the latter materials, much of this research being exploratory in the sense of gathering new property data. The situation, so far as graphite is concerned, is somewhat more fortunate than with the other refractory solids in the sense that a great deal is already known about its basic properties. This stems both from the fact that the carbon-carbon bond has been of interest to chemists for a long time (and graphite can be considered as a very large aromatic molecule, if desired) and the fact that its properties, both as a function of temperature and of radiation damage, are of critical importance to nuclear reactor designers. It is still true, of course, that such fundamental questions as why graphite remains solid to such a high temperature and why it has such a high thermal conductivity cannot entirely be answered at the present time. It is, nonetheless, meaningful and instructive to consider such problems in the light of existing knowledge. This is what the present paper will attempt to do. Before going on, it may be appropriate to classify graphite and justify its discussion before readers primarily interested in metals. Graphite is comparatively unique among materials in that there is always a property or group of properties which precludes calling it either a metal, a semiconductor, or a ceramic. It has the high electrical and thermal conductivities of a metal, but the artificial, poly-crystalline types show a negative thermal coefficient of electrical resistivity, generally characteristic of semiconductors. On the other hand, semiconductors, by definition, show an ever increasing resistivity as the temperature is lowered, whereas graphite approaches a finite, and, indeed, a rather low resistivity in the region of 10°K and, furthermore, a good single crystal of graphite has a positive temperature coefficient, as for a metal.' On still another hand, its porosity and brittleness at lower temperatures would put graphite in the ceramic class although, unlike most ceramics, it is readily machinable and has a high resistance to thermal shock. All things considered, it is probably more nearly appropriate to call graphite a metal than anything else. Although certainly outstanding in some ways, graphite has its peculiarities and, especially if the reader is unfamiliar with the data, it is probably valuable to review some representative property variations at high temperature. This review is meant to be mainly illustrative and no attempt has been made to be exhaustive. Review of High Temperature Properties At ordinary pressures, graphite does not melt, but sublimes directly into the gaseous phase at about 3700°C. Although the phase equilibrium diagram is still in some doubt, graphite will melt, at a slightly higher temperature, at pressures in excess of about 100 atm. The chief difficulty of using graphite in an oxidizing atmosphere is that the reaction rate becomes quite high at fairly low temperatures. If a threshold oxidation temperature2 is defined as the temperature at which graphite loses 1 pet of its weight in 24 hr, the value in air is 450°, the value in steam is 700°, and the value in carbon dioxide is 900°C. Efforts are presently being made to raise this threshold temperature either by impregnation with a retardant of some type (sodium tung-state and phosphoric acid, for example) or by a suitable metal or oxide coating. It is probably fair to say that, to date, these attempts have not shown any outstanding success in all respects. Most commercial graphites are fabricated by impregnating a carbon flour (say of coke or lampblack particles) with some type of hydrocarbon

Jan 1, 1959

By H. M. Howe

(New York: Meeting, October, 1913.) 1. INTRODUCTION.-This paper gives the results of our micro-graphic determinations of the position of Ae3 in a series of 14 hypo-eutectoid steels of varying carbon content, one of them very rich in phosphorus, and of SEe for one hyper-eutectoid steel. We have pro-ceeded chiefly by noting the temperature -at which the reabsorption of the pro-eutectoid element is found to be complete after a 30-min. holding, but in part also by noting the temperature at which its precipitation begins. Observations on these same steels by Messrs. Burgess, Crowe, and Rawdon, of the United States Bureau of Standards, are given in a paper' issued simultaneously with this, while in a third paper s one of us compares these data with those of earlier observers. These three papers are treated as one whole by numbering their sections, tables, and illustrations continuously, and by setting the folding plates of micrographs at the end of the last paper. THE COMPOSITION OF THE STEELS EXPERIMENTED ON is given in Table I. Notation. and Definitions.-Following Osmond's development of Tschernoff's notation; in which " Ac3 " is the upper limit of the hypo-eutectoid part of the transformation range as observed in heating up, and " Ar3 " is that same limit as observed in cooling down, and following the usual custom of calling the upper limit of the hyper-eutectoid part of that range "SE," we may go farther and call this latter limit " SEc " when observed in heating up .and " SEr " when observed in cooling down.

Jan 6, 1913

By George W. Sears

In preparing this symposium, our ambition was to elicit authoritative expression of opinion concerning important selected phases of the industry from men active in it. Responses to requests for contributions were gratifying, especially so in view of the short time available. The generous and cooperative spirit of the industry as a whole is amply evident. Responses were received from the following, who are therefore the true authors of the paper: W. G. Adamson, General Manager of the pershin; Quicksilver Co., Lovelock, Nev.; Dudley Baird, Vice President, Pacific Foundry Co., San Francisco; Walter W. Bradley, State Mineralogist of California; W. D. Burcham, General Manager of the Brewster Quicksilver Consolidated, Terlingua, Tex.; William Forstner, San Francisco; H. W. Gould, of H. W. Gould & Co., San Francisco; Marcus Hulings, General Manager of the Chisos Mining Co., Terlingua, Tex.; Frank J. Katz, Chief Engineer, Division Mineral Statistics, United States Bureau of Mines, Washington, D. C.; Lloyd J. Lathrap, Superintendent, Nevada Quicksilver Mines, Inc., Lovelock, Nev.; W. R. Moorehead, General Manager, New Idria Quicksilver Mings, Inc., Idria, Calif.; F. W. Oakes, Jr., Terlingua, Tex.; C. N. Schuette, San Francisco. Brief Economic History of Quicksilver in the United States Quicksilver ore was first discovered in the United States at what was later the New Almaden mine in California, in the year 1824. Production also began here, but not until 1850, when it was stimulated by the active demand caused by gold-mining operations. Prospecting for quicksilver was active, high-grade ores were found and ample production lowered the price from $100 per flask in 1850 to about half that figure for the greater part of the next 10 years. During the succeeding decade, many new quicksilver mines were found; production increased at a time when the local demand diminished, so that most of the product was exported. The third decade of quicksilver mining in the United States witnessed the development of the pan amalgamation process, particularly in Com-stock silver-mining operations. A suddenly increased demand sent prices soaring, the all-time peak of quicksilver production followed, and the highest price was soon replaced by the lowest one on record. Huge quantities of quicksilver were exported between 1870 and 1880 and exports continued in decreasing measure for three decades to 1910. In

Jan 1, 1930

By E. R. Parker, R. H. Thielemann

The conventional short-time tensile test provides a reliable means of predicting the sustained load-carrying capacity of steels only when the temperature is such that continuous plastic flow does not occur. At elevated temperatures, stresses considerably less than the short-time rupture value may produce continuous flow, with fracture occurring only after long periods of time. The amount of flow or creep accompanying failure varies for different steels, and depends, to a large extent, on the temperature and the duration of the test. Service records of cracking stills, steam superheaters and high-temperature boilers have shown that brittle fractures sometimes occur with little or no warning. In installations of this type, localized stresses are often encountered, and steels must be capable of withstanding a certain amount of deformation without fracture. The sustained-load rupture test determines the expected life and corresponding ductility of steels at various stresses and temperatures. It also yields additional information regarding the effect of micro-structure and metallurgical stability on the high-temperature properties. Present Status of Sustained-load Rupture Test The sustained-load rupture test conducted at elevated temperatures is not entirely new. Dr. Zay Jeffriesl presented in 1919 the results of a large number of rupture tests made on copper, iron and tungsten. These tests were made with various strain rates and at temperatures ranging from the boiling point of liquid air to 1000° C. At that time he observed the interesting phenomenon characteristic of metals, that a temperature exists below which a metal is ductile and breaks with a transcrystalline fracture (through the grain) and above which the metal is brittle and breaks with an intergranular fracture (through the grain boundaries). He observed that this temperature varied with the testing speed, and that a minimum temperature, slightly above the recrystallization temperature, existed at which the cohesion of the grains themselves was

Jan 1, 1939

By R. H. Thielemann, E. R. Parker

The conventional short-time tensile test provides a reliable means of predicting the sustained load-carrying capacity of steels only when the temperature is such that continuous plastic flow does not occur. At elevated temperatures, stresses considerably less than the short-time rupture value may produce continuous flow, with fracture occurring only after long periods of time. The amount of flow or creep accompanying failure varies for different steels, and depends, to a large extent, on the temperature and the duration of the test. Service records of cracking stills, steam superheaters and high-temperature boilers have shown that brittle fractures sometimes occur with little or no warning. In installations of this type, localized stresses are often encountered, and steels must be capable of withstanding a certain amount of deformation without fracture. The sustained-load rupture test determines the expected life and corresponding ductility of steels at various stresses and temperatures. It also yields additional information regarding the effect of micro-structure and metallurgical stability on the high-temperature properties. Present Status of Sustained-load Rupture Test The sustained-load rupture test conducted at elevated temperatures is not entirely new. Dr. Zay Jeffriesl presented in 1919 the results of a large number of rupture tests made on copper, iron and tungsten. These tests were made with various strain rates and at temperatures ranging from the boiling point of liquid air to 1000° C. At that time he observed the interesting phenomenon characteristic of metals, that a temperature exists below which a metal is ductile and breaks with a transcrystalline fracture (through the grain) and above which the metal is brittle and breaks with an intergranular fracture (through the grain boundaries). He observed that this temperature varied with the testing speed, and that a minimum temperature, slightly above the recrystallization temperature, existed at which the cohesion of the grains themselves was

Jan 1, 1939