Search Documents

By J. W. Koger, R. E. Hurnrnel

QUENCHED, bcc p brass, P1, transforms to a mar-tensitic phase, when it is cooled below room temperature.' This transformation can be followed using resistance measurements since the resistivity of the martensitic phase is considerably larger than that of the parent phase, Fig. 1.' phillips3 first reported that, when Cu-Zn alloys containing between 37.0 and 39.0 wt pct Zn were quenched from the 0 region to room temperature, variable amounts of a phase could be observed depending on the mode of quenching. If the quench occurs very rapidly, the a phase forms by a "massive transformation". The resultant phase has the same composition as the high-temperature P phase from which it was formed. If the quench is less severe, the alloy is retained largely in the p form; however, some a is formed by precipitation. In this case, a contains more copper than the high-temperature 0 phase from which it has formed. The a phase most probably does not undergo a transformation in the temperature range where p transforms to low-temperature martensite. This can be deduced from the Eesistivity-temperature relation which is linear in this temperature range, Fig. 2. The stable a phase which is present along with R. E. HUMMEL is Assistant Professor, Department of Metallurgical and Materials Engineering, University of Florida, Gainesville, Fla. J. W. KOGER, Junior Member AIME, formerly with University of Florida, is now with Oak Ridge National Laboratory, Oak Ridge, Tenn. Manuscript submitted December 13, 1967. IMD.

Jan 1, 1969

By J. H. Swisher, E. O. Fuchs

Rate equations were derived to describe the kinetics of internal oxidation of cylinders and spheres. The derived equations for cylinders were checked experimentally by means of sub scale thickness and electrical conductivity measurements on Cu-Cr alloy wires. The properties of the internally oxidized samples were examined with conductivity applications in mind. It was possible to produce uniform dispersions of Cr2O3 in copper with an initial chromium content as high as 3 wt pct. While electrical conductivities only a few pct less than that of OFHC copper were obtained, the Cr2Os particle size and spacing were too large for effective dispersion hardening. T.HE process of internal oxidation has been used widely in basic studies of the permeability of gases in metals. In a review article, Rapp1 has discussed the principles of internal oxidation in considerable detail. From a technological standpoint, internal oxidation is often considered undesirable, since it is a means by which inclusions can be introduced into an otherwise clean material. Another important aspect of internal oxidation is its use as a means of dispersion hardening a material. Broutman and Krock2 discuss this and other methods for making dispersion hardened alloys. The only internally oxidized material known to the authors which is commercially available is a Cu-BeO alloy.3'4 This alloy is made from Cu-Be alloy powder, using a so-called Rhines pack. It has a tensile strength of 80,000 psi and retains its strength at relatively high temperatures. The objectives of the present study were to derive rate equations for the internal oxidation of cylinders and spheres, to check the derived equations for cylinders experimentally, and to examine the structure and properties of internally oxidized Cu-Cr alloys. The Cu-Cr system was chosen for this study because uniform dispersions are obtainable at high alloy contents, which is a desirable characteristic in dispersion hardened materials. RATE EQUATIONS FOR VARIOUS GEOMETRIES A number of authors5--9 have derived equations to describe internal oxidation kinetics. These derivations differ somewhat in mathematical assumptions and approximations, and all except one of the derivations deal exclusively with the internal oxidation of plates. The exception is a brief treatment of cylindrical and spherical geometries given by Meijering and Druy-vesteyn9 as a part of a comprehensive paper on the general subject of internal oxidation. These authors did not obtain rate data to check their derivations, although they did show that the hardness profile across an internally oxidized sample is directly related to the rate of interface movement. For cylindrical and spherical geometries, a quasi-steady-state approximation is needed to circumvent mathematical complications in obtaining a solution to the basic differential equations. In using this approximation, we consider the concentration gradient of dissolved oxygen in the internally oxidized zone or sub-scale to be the same as the gradient which would be present if there were no movement of the subscale interface. The steady-state approximation introduces an error of about 1 pct in computing the rate of internal oxidation of an Fe-1.0 pct Mn alloy plate, if the present method is compared to the more exact method of Wagner.7'10 The details of the derivations of the rate equations for cylinders and spheres are given in the Appendix, and only the results of these derivations are given below. The final equations obtained by Meijering and Druyvesteyn9 can be shown to be equivalent to our Eqs. [1] and [2], although the two approaches are somewhat different. Cylindrical Geometry. [2] where r1 is the outer radius of the cylinder or sphere, cm, r2 is the radius of the unreacted core, cm, see Fig. l(a), D is the diffusion coefficient of oxygen in copper, cm2 per sec, %O is the concentration of dissolved oxygen at the surface of the specimen, wt pct, %Cr is the initial chromium concentration in the alloy, wt pct, and t is the reaction time, sec. Plate Geometry. The analogous rate equation for a plate has been derived previously for internal oxidation of Fe-Al alloys.8'11 For Cu-Cr alloys, we may write the same equation as follows: [3] where r1 is the half-thickness of the plate, cm, and r2 is the distance from the mid-plane to the subscale intherate is An analysis of Eqs. [1], [2], and [3] shows that for a plate the rate is completely parabolic. The initial

Jan 1, 1970

By Reginald E. Hore

Since the discovery of silver at Cobalt, Ontario, in August, 1903, more than 100,000,000 oz. of silver have been produced by the mines in the Nipissing district, and there is reason to believe that at least as much more will be produced in the nex five years. The estimated value of the aggregate output o ore to the end of 1910 is $48,327,280. The ore yielded 93,977,833, oz. of silver and was mined at a net profit of abou $16,000,000. For 1910 the production was 30,558,825 oz., valued at $15,436,894, and yielding a profit of about $9,000.000. The details of the production of the Cobalt district for the years 1904 to 1909, inclusive, as reported by the Ontario Bureau of Mines, are given in Table I. The shipments from Cobalt are in the form of smelting-ore, concentrates from milling-ore, and bullion. The smelting-ore is largely high grade, averaging about 3,000 oz. per ton A smaller return is from what is called low-grade ore and which

Jan 1, 1912

By P. E. Senseny

INTRODUCTION Massive hydraulic fractures have been used since 1949 in the petroleum industry to enhance production rates and increase recoverable reserves. Currently, a research program, the Multi-Well Experiment, is underway to develop the understanding and technology to a1 low economic production of the large gas reserves of the low permeability, lenticular sandstone formations in the western U.S. (Atkinson, et al, 1981; Northrop and Sattler, 1983). Use of state- of-the-art hydraulic fracturing techniques is a part of this investigation. As a portion of an extensive core program in support of this experiment (Sattler, 1983), fracture toughness has been determined for 56 sandstone, shale, mudstone, or siltstone horizons from three wells in the Piceance Basin. The role of fracture toughness in hydraulic fracturing is not well understood because other factors, such as in situ stress, dominate fracture geometry and containment. Rubin (1983) concluded from analysis of his laboratory hydrofracture experiments that fracture toughness should be included in design and numerical simulation of hydraulic fractures. However, van Eekelen (1982) contends that the stress intensity at the crack front should be so much greater than the fracture toughness of the rock that toughness can have no importance. Generally, fracture toughness and other material properties, such as elastic moduli and permeability, are thought to be of secondary importance in determining fracture geometry and containment. In spite of this, there is a need to acquire a more quantitative understanding of their importance for accurate design and simulation calculations. Analysis of fracture geometry and containment data from hydraulic fracturing experiments carried out in formations where fracture toughness and other rock properties are

Jan 1, 1984

By R. E. Head

UNDER existing economic conditions, the treatment of gold ores occupies an outstanding position in metallurgical activity. The increased price of gold has automatically brought about a reclassification of old dumps and low-grade orebodies, and many that formerly were considered valueless are now being vigorously investigated and worked. This situation has developed problems that have taxed the ingenuity and ability of metallurgists to the utmost. Some gold ores give a high extraction of gold by standardized methods of treatment; other ores of apparently similar character yield but a relatively small percentage of their gold when treated by the same processes.

Jan 1, 1936

By P. S. Kotval, O. H. Nestor

Stacking fault energy measurements of nickel-base alloys have been mainly confined to binary and ternary systems. In this paper, the stacking fault energy has been measured by the rolling texture method in a series of ten alloys which comprise successive additions of Cr, Mo, Fe, and C to pure nickel, eventually resulting in an alloy of the composition of Hastelloy alloy X. The alloys studied here are single-phase, solid solutions with the exception of two alloys in which some undissolved particles of "primary" carbide have been retained. It is found that successive additions of chromium, molybdenum, and iron all lower the stacking fault energy, with iron having only a minor effect. The stacking fault energy is found to increase when carbon is added in solid solution. The results from the rolling texture measurements are correlated with thin foil observations of dislocation substructures in these alloys. In a recent paper' it was pointed out that the dislocation substructure of various superalloy matrices could be classified into three broad categories based on 'high', 'medium', and 'low' stacking fault energy. It has also been demonstrated2 that the dislocation substructure in each of these categories has a well defined role in the nucleation of strengthening precipitates which is different from the role played by the dislocation substructure in other categories. Thus, it becomes desirable to understand the influence of various solute elements on the stacking fault energy and hence on the dislocation substructure of the matrix, before any further development of superalloys by mi-crostructural predesign can be undertaken. Recently, Beeston and France have studied the influence of increasing solute additions on the stacking fault energy of a series of binary nickel-base alloys relevant to the Nimonic series using the rolling texture method, and have then estimated the effect of a given alloy addition in five commercial Nimonic alloys. However, comparison with stacking fault energy data from other investigations''5 suggests that the influence of a given solute element in a nickel-base binary system is not necessarily the same in a ternary or more complex superalloy system. Accordingly, the present work was undertaken to study the effect of successive addition of solute elements to pure nickel, the final composition being the nominal composition of Hastelloy X. The rolling texture method of stacking fault energy measurement was used since it can be used for the whole range of stacking fault energy values and does not have the disadvantage of, say, the Node method which is only applicable to low values of stacking fault energy. In addition, the rolling texture method provides a means of determining the stacking fault energy which is statistically more significant than that provided by other methods. EXPERIMENTAL TECHNIQUES Button heats of alloys of the compositions shown in Table I were prepared. Each button was remelted not less than four times. After a slight deformation (approximately 5 pct) all alloys were homogenized at 2200°F except alloys, H . I, and J. Alloys H and I were solution heat treated at 2150°F and alloy J at 2282OF. The buttons were cold worked by rolling, using "end-to-end" passes and intermediate anneals at the homogenization temperatures mentioned above. After each annealing treatment the samples were rapidly water quenched to avoid any precipitation. In alloys F and I, however, a few particles of "primary" carbides were retained even after the homogenization treatments at the temperatures mentioned above. Part of the solution heat treated material was cold worked to 0.04-in.-thick sheet and the penultimate reduction was -50 pct of deformation as recommended by Dillamore et al. All annealing was carried out in vacuo within sealed quartz capsules. Some of the material from each alloy was rolled down further to 0.004 in. strip for thin foil transmission electron microscopy specimens. Specimens of this strip were annealed at the homogenization temperature for 1 hr and then strained 7 pct by rolling at room temperature. Thin foils were prepared from the strip specimens by the 'window" technique using an Ethanol-Perchloric acid electrolyte at 32°F and a voltage of 22 v. Stainless steel cathodes were employed. All transmission electron microscopy was performed in a JEM-7 electron microscope using an accelerating voltage of 100 kv. Specimens from the 0.04 in. sheet which had been rolled -60 pct in the final pass were electropolished to remove the surface layers to a depth of approximately 0.002 in. Rolling texture pole figures for all the alloys were determined using a Schulz ring and nickel filtered CuKa radiation at 50 kv and 20 ma. The texture parameter Io/(lo + I,,) (where Io is the

Jan 1, 1970

By Jay N. Fairbanks, Richard G. Robinson

This paper discusses a computer program and related formulas for fire fighting responses by coal mine personnel. The computer will interpret the mine air analysis, print reports, and provide relevant graphs allowing quick and accurate responses to coal mine fires.

Jan 1, 1983

By Paul D. V. Manning

MAGNESIUM is an exceedingly strategic material but the importance of its production at the time this war started was not realized. Our Government then suddenly became much alive to the need of a tremendous increase in magnesium output, and became a participator in the industry. In this paper an attempt will be made to given an over-all picture of the industry as it has been, and is being, developed. The present war is giving a great acceleration to the use of lighter metals. Development of facilities for production of great tonnages of aluminum and magnesium is bound to bring about some interesting changes in later peace times because costs will be low and production capacities high. As our knowledge of the metallurgy of magnesium alloys increases, this metal will become of vital peacetime importance and will be used in ways we do not now imagine. Household refrigerators, furniture, automobiles, even houses will all be lightened through the use of magnesium.

Jan 1, 1943

By J. L. Gillson

The big mass of anorthosite in the Lake Sanford district and the bodies of titaniferous magnetite that occur in a small area near the south margin of the mass have been described repeatedly, and the puzzling problems of the genesis of the rocks and ores have stimulated the deductive reasoning of geologists for a hundred years. Some of these men have taken a leading part in describing the anorthosite rock and forming hypotheses concerning its origin; some have contributed most to the study of the ore deposits; and some have made classical Studies introducing a basic approach to the problems of the anorthosite rock and genesis of the titaniferous magnetites. Much of the writing on the problems of rock and ore genesis has been based on physical-chemical reasoning rather than on field and microscope observations of the rocks and ores. Most of these geologists conclude that the anorthosite was formed by true magmatic crystallization, involving previous settling or squeezing out of ferromagnesian minerals from the parent magma. The associated gabbro is a separate segregation or later intrusion, and the lighter colored and finer grained facies of the anorthosite is either a chilled border zone of the anorthosite or the result of granulation by crushing of the coarse, dark blue rock of the main mass. This blue rock, called the Marcy type, is named after the highest peak in the range. The finer grained and lighter colored rock is called the Whiteface, after another mountain appropriately named for a cliff colored by this facies of the anorthosite.

Mar 1, 1956

By AIME AIME

The following financial report of the Treasurer of the United Engineering Society is published for the information of members NEW YORK, February 15, 190S. To the Board of' Trustees, United Engineering Society I beg to submit herewith the report of the Treasurer as of December 31, 1907. Your attention is called to the fact that the resources and liabilities, receipts and disbursements statements cover all the financial transactions of the United Engineering Society from its organization up to December 31, 1907. The income and expenses of operating the building during the whole operating period from December 1 to December 31, 1907, somewhat in excess of twelve months, are given. Included in the expenses, amounting in all to $52,647.11, will be found an item entitled "Building Equipment (construction account)." The expenditures under this item were not made for the operating expenses of the building, they represent a construction account, properly speaking, covering expenditures for furnishings and equipment of the building. The Founders' Agreement specifically provides for this class of expenditure under the provision that the Founder Societies shall each be liable for a charge not to exceed $200,000 of principal, which shall include the land and building completed and ready for occupancy, together with the " furnishings, equipment and personal property therein." Certain details of equipment are yet to be supplied, and it. is proposed in the near future to call upon the Founder Societies for an assessment on their respective land and building funds to cover this item of building equipment. Such action would enable the item of $10,039.85 to be transferred to the income account and reduce correspondingly the assessment

Mar 1, 1908

By Roland Blanchard

Recent discovery at Mount Isa of copper mineralization in commercial amount at a depth of 1000 ft., coinciding with downward termination of ore at about the same depth within the larger silver-lead-zinc lenses that have been the standby of Mount Isa's production to date, has been cited as an example in support of mineral zoning. A previous paper by the author and Graham Hall1 furnished a detailed description of the geology of the ore at Mount Isa as exposed up to that time, but necessarily dealt mainly with the silver-lead-zinc mineralization. Most of the geologic facts that constitute the first half of the present paper were set forth in the previous one in much greater detail, with full supporting evidence for the facts cited. The large amount of underground development (approximately 20 miles) and the extensive exploration carried out by diamond drilling (100,000 ft.) at Mount Isa, added to extensive microscope work conducted over a period of years, both by the company's staff and by others, had made possible the calculation within fairly close limits of mineralogical composition of the principal mineralized block of ground down to 1000-ft. depth, and had established closely the mineral succession, with reasons for deposition of the various minerals in the patterns now occupied by them. The geologic facts as outlined in the previous paper remain as stated; but because substantial development within the new copper ore body and further exploratory diamond drilling within the new silver-lead-zinc area (Racecourse) have taken place since that paper was written, statements and figures relating to those two areas in the present paper supersede those furnished in the previous one. The recent work likewise has established more clearly the paragenetic relationship between the chalco-pyrite and galena. Evidence confirming the relationship is furnished in the present paper. The facts of ore occurrence at Mount Isa show Accepted Zonal Succession Silver sulphantimonides Galena Sphalerite Tetrahedrite Arsenical sulphides Chalcopyrite Pyrrhotite Mount Isa Succession I In the main but prob- Silver sulphantimonides ably not wholly Tetrahedrite I contemporaneous Galena Pyrrhotite Sphalerite Arsenical sulphides They show further: (I) that instead of the silver-lead minerals yielding to increased zinc in depth, the zinc yields to increased silver-lead; (2) no dovetailing of the silver-lead-zinc sulphides into chalcopyrite takes place; (3) despite the large amount of pyrrhotite deposited in the district (estimated at upward of 100,000,000 tons), its deposition took place under moderately low temperature conditions; (4) no evidence has been found for increase in temperature of deposition, with depth, to deepest exploration in ore (1475 ft.). The anomalous condition at Mount Jsa, both as to the unorthodox mineral succession and the largely unorthodox patteru of mineral distribution, is explained in the present paper,

Jan 1, 1949

By Roland Blanchard

Recent discovery at Mount Isa of copper mineralization in commercial amount at a depth of 1000 ft., coinciding with downward termination of ore at about the same depth within the larger silver-lead-zinc lenses that have been the standby of Mount Isa's production to date, has been cited as an example in support of mineral zoning. A previous paper by the author and Graham Hall1 furnished a detailed description of the geology of the ore at Mount Isa as exposed up to that time, but necessarily dealt mainly with the silver-lead-zinc mineralization. Most of the geologic facts that constitute the first half of the present paper were set forth in the previous one in much greater detail, with full supporting evidence for the facts cited. The large amount of underground development (approximately 20 miles) and the extensive exploration carried out by diamond drilling (100,000 ft.) at Mount Isa, added to extensive microscope work conducted over a period of years, both by the company's staff and by others, had made possible the calculation within fairly close limits of mineralogical composition of the principal mineralized block of ground down to 1000-ft. depth, and had established closely the mineral succession, with reasons for deposition of the various minerals in the patterns now occupied by them. The geologic facts as outlined in the previous paper remain as stated; but because substantial development within the new copper ore body and further exploratory diamond drilling within the new silver-lead-zinc area (Racecourse) have taken place since that paper was written, statements and figures relating to those two areas in the present paper supersede those furnished in the previous one. The recent work likewise has established more clearly the paragenetic relationship between the chalco-pyrite and galena. Evidence confirming the relationship is furnished in the present paper. The facts of ore occurrence at Mount Isa show Accepted Zonal Succession Silver sulphantimonides Galena Sphalerite Tetrahedrite Arsenical sulphides Chalcopyrite Pyrrhotite Mount Isa Succession I In the main but prob- Silver sulphantimonides ably not wholly Tetrahedrite I contemporaneous Galena Pyrrhotite Sphalerite Arsenical sulphides They show further: (I) that instead of the silver-lead minerals yielding to increased zinc in depth, the zinc yields to increased silver-lead; (2) no dovetailing of the silver-lead-zinc sulphides into chalcopyrite takes place; (3) despite the large amount of pyrrhotite deposited in the district (estimated at upward of 100,000,000 tons), its deposition took place under moderately low temperature conditions; (4) no evidence has been found for increase in temperature of deposition, with depth, to deepest exploration in ore (1475 ft.). The anomalous condition at Mount Jsa, both as to the unorthodox mineral succession and the largely unorthodox patteru of mineral distribution, is explained in the present paper,

Jan 1, 1949

By M. G. Benz, J. F. Elliott

A new type of solution calorimeter has been constructed to measure heats of mixing, enthalpy increments, and heats of fusion, formation, and reaction at temperatures above 1000°C. With it, measurements hove been made of the partial molar heats of mixing joy tin in the Cu-Sn system from 0 to 13 at. pet Sn at 1127°C and fir nickel in the Cu-Ni system from 0 to 9 at, pet Ni at 1200°C. The integral molar heat of mixing for the Cu-Sn system is strongly negative with a calculated minimum value corresponding to the composition Cu3Sn. The integrnl molar heat of mixing for the Czi-Ni system is slightly positive at these temperatures. These integral molar values have been measured with a probable error less than 30 cal per g-atom at an atom fraction of nickel or tin equal to 0.1. The estimated probable error for the Cu-Sn system is approximately 450 cal for a measured heat of solution of approximately 9000 cal. For the Cu-Ni system it is approximately 700 cal for a measured heat of' solution of approximately 60 cal. A new type of heat of solution calorimeter was designed and constructed to provide a more accurate experimental method for determining heat effects at high temperatures, (T > 1000°C). With it, partial molar heats of mixing, enthalpy increments, heats of fusion, and heats of formation and reaction for metal systems can be measured directly. Previously it has been necessary to rely upon the use of the dropping calorimeter or the van't Hoff equation applied to equilibrium data for this information. For the most part equilibrium data are scarce and difficult to obtain in many cases, and it has been necessary to rely upon the "method of mixtures" for the desired enthalpy measurements. An earlier study1 provides a prototype for this work. The "method of mixtures" as outlined by K. K. kelley,2 "consists of dropping the substance under investigation from a furnace, with controlled and measured temperature, into a calorimeter operating at or near room temperature.'' In this manner the change in the total heat content (enthalpy) of the substance between the temperature of the furnace and that of the calorimeter is determined. In order to determine high-temperature heats of mixing, enthalpy increments, and heats of fusion, formation, and reaction, it is necessary to take the difference between two such measurements, one before and one after the occurrence of the enthalpy change being studied. The desired enthalpy change is then the small difference between two large numbers. Small errors in the large numbers are included as large errors in this small difference. It is this difficulty that must be avoided for accurate measurement of the desired functions. The procedure with the new solution calorimeter consists of dropping the substance under investigation from a furnace, with controlled and measured temperature, into a solution calorimeter operating in the temperature range of 1000o to 1200°C. Measurements in the range of 1200" to 1600°C are planned for the future. By selection of the composition and

Jan 1, 1964

By Douglas A. Sloan

Who would believe that young elementary school children could understand something as complex as the mining industry? The Challenge The challenge of accomplishing this is tremendous. An examination of Canadian school children indicated that they knew very little about the world of work in general, and hardly anything about the mineral resource industry in particular. It calls to mind the story about two youngsters who decided to play house. The little girl played her role well as she went about the house doing things she had watched her mother do every day. When it was the little boy's turn, he grabbed his lunch, waved goodbye to his "wife," jumped on his bicycle and pedalled furiously down to the end of the driveway-where he stopped. The youngster explained that he saw his dad go out of the driveway each morning, but he didn't know where he went, or what he did on the job. When you stop to consider the number of families today with two working parents, you can begin to appreciate the importance of the opportunities for role identity provided by this project. The Approach The challenge of teaching the school children of Canada about the world of work and, specifically, the mining industry is the challenge which the Canadian Institute of Mining and Metallurgy met with the Curriculum Development Research project. It started when a small, dedicated group of Vancouver members met Dr. Doreen Binnington. After this meeting, Dr. Binnington, an expert in curriculum development at the University of British Columbia, set herself to develop a curriculum program for the elementary shcools which accomplishes two main goals: It uses the "Identity Approach," developed by Dr. Binnington, an expert in curriculum development at the enable students to understand and appreciate the contribution of people, in this case, working with mineral resources. It has pupils enthusiastically exploring the importance of rocks, minerals, and the mining industry in their lives [(Fig. 1)]. Evolution of the Curriculum Development Research Project When the curriculum development research project was presented to the Vancouver Branch of the Canadian Institute of

Jan 1, 1981

The Joint Session on Continuous Cast- ing, of the Institute of Metals Division and the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers, convened in the Jade Room of, the Hotel Waldorf-Astoria, New York City, on Feb. 23, 1944, at 9:15 o'clock, Carl E. Swartz presiding. C. E. SWARTZ.-It is gratifying to see so many out at what may seem an early hour for the beginning of A.I.M.E. sessions, but I think this number-some fifty or sixty of you-is an adequate expression of the interest in these processes all over the United States, and possibly in foreign countries. I would like to ask those who feel that this type of program is of value to you to write or speak to some one of the Institute of Metals Division officers and suggest other topics for symposiums. We have a feeling that some of these current practices are of interest and we believe that under proper sponsorship many of the companies will be willing to give publicity to processes such as those that will be discussed today. Also, we would like suggestions and criticisms, so that the next ones can be better. The subject of continuous casting is not new, of course. The two papers on the program this morning will adequately cover the history and some of the earlier processes, some of the theory and some of the practice, some of the reasons why these various methods did not work. I was rather interested in discovering, when thumbing through one of the A.I.M.E. publications the other night, an article on continuous casting. I was not aware that the A.I.M.E. had published any papers on continuous casting, but there may be a number. The one that I happened to find was published in the 1915 volume, on the Mellen rod- casting process, and so we might say this is not the first session in which these subjects have been under discussion. However, there have been many improvements since then in all fields of metallurgical and mechanical engineering; consequently, I think that the papers today will be a little more involved and a little more complete in their technique. The first paper today will be given by one of our gentlemen of the press, who has done one of the outstanding jobs in this country in calling to our attention some of the newer processes that are being considered and being used in the metallurgical indus-

Jan 1, 1945

By Carl E. Swartz

The Joint Session on Continuous Casting, of the Institute of Metals Division and the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers, convened in the Jade Room of the Hotel Waldorf-Astoria, New York City, on Feb. 23, 1944, at 9:15 o'clock, Carl E. Swartz presiding. C. E. SWartz.—It is gratifying to see so many out at what may seem an early hour for the beginning of A.I.M.E. sessions, but I think this number-—some fifty or sixty of you —is an adequate expression of the interest in these processes all over the United States, and possibly in foreign countries. I would like to ask those who feel that this type of program is of value to you to write or speak to some one of the Institute of Metals Division officers and suggest other topics for symposiums. We have a feeling that some of these current practices are of interest and we believe that under proper sponsorship many of the companies mill be willing to give publicity to processes such as those that will be discussed today. Also, we would like suggestions and criticisms, so that the next ones can be better. The subject of continuous casting is not new, of course. The two papers on the program this morning will adequately cover the history and some of the earlier processes, some of the theory and some of the practice, some of the reasons why these various methods did not work. I was rather interested in discovering, when thumbing through one of the A.I.M.E. publications tile other night, an article on continuous casting. I was not aware that the A.I.M.E. had published any papers on continuous casting, but there may be a number. The one that I happened to find was published in the 1915 volume, on the Mellen rod-casting process, and so we might say this is not the first session in which these subjects have been under discussion. However, there have been many improvements since then in all fields of metallurgical and mechanical engineering; consequently, I think that the papers today will be a little more involved and a little more complete in their technique. The first paper today will be given by one of our gentlemen of the press, who has done one of the outstanding jobs in this country in calling to our attention some of the newer processes that are being considered and being used in the metallurgical indus-

Jan 1, 1945

By P. A. Vukmanic, M. Gensamer

Only recently has it been realized that preferred orientations are common in hot-rolled steels. In a recent paper, N. P. Gossl stated that hot-rolled mild steel exhibits a texture different from that characteristic of cold-rolled steel. No complete study of these hot-rolling textures has been reported using the pole-figure method of Wever. The material used in the work reported in this paper was the same material used by Gensamer and Mehl2 in a recent study of preferred orientations in cold-rolled steel, to which reference may be made for the composition and thermal history of the steel. Automobile-body sheet bar 1/4 in. thick was hot-rolled at two temperatures, 780' and 910' C. (1436' and 1669' F.). These temperatures refer to the temperature of the furnace in which the steel was heated; after each pass the steel was returned to the furnace and held there long enough to return to temperature. Although no accurate method was used to measure the temperature after each pass, it was estimated by color that only a slight drop in temperature occurred. In order to determine the effect of any preferred orientation that might have persisted through the normalizing treatment, one specimen at each temperature was rolled in the same direction as the original working direction and the other at right angles to it. The total reduction in each case was 85 per cent, the specimens having been reduced from 0.250 to 0.0375 in. in five passes. Final cooling was in air. Pinhole reflection photograms were taken of all four specimens, with the rolling direction vertical and the X-ray beam at an angle of 7' with the transverse direction (the transverse direction is defined as that direction in the rolling plane perpendicular to the rolling direction). These photograms, taken with a Mo target at 35 kv., are reproduced in Figs. 1, 2, 3 and 4. They show that a more pronounced texture was developed by the low-temperature rolling (780' C.), and that of the two

Jan 1, 1937

By Robert Goodwin, Frank R. Milliken

IN September 1939, the Ohio Copper Co. inaugurated the treatment of its copper-bearing mill tailings at Lark, Utah. These tailings had been accumulated during the regular operation of the Ohio Copper mine and mill over the period 1907 to 1919. Gravity concentration had been employed except for a comparatively short period in 1919, when flotation was used. The ore milled during that period assayed about 1 per cent Cu. The chief copper mineral, chalcocite, was disseminated in a shattered quartzite, mainly along fracture or cleavage planes. The quartzite gangue was extremely hard and grinding to liberation resulted in excessive sliming of the "sooty" chalcocite, with consequent high tailings losses. Recovery on the seven million tons treated was probably less than 6o per cent of the total copper content. As early as 1918, attempts had been made to sample the dump. In 1928, a complete sampling program was undertaken. The sampling consisted of seventy-four 5-in. post auger holes drilled to the full depth of the dump at regular intervals of 250 ft. Each 10-ft. portion thereof comprised a sample for analysis. Each sample was screened, rolled, divided into three parts, dried and assayed. The reject was retained for testing purposes. From the depth of the auger holes a contour map of the dump was plotted, Fig.1, which gives percentages of tonnage and copper content. The tonnage within the limit of the drill holes was estimated at about five million tons with an average content of 0.42 per cent Cu, 31 per cent of which (0.13 per cent) was acid-soluble. A screen analysis of the composite dump sample is shown in Table I. Flotation tests by several companies and individuals were then made, the results of [ ] which ranged from 62 to 74 per cent recovery. On the basis of these, a Zoo-ton pilot plant employing straight flotation was built and operated for a few months. Operation of this plant was unsuccessful, as no provision had been made to handle the copper-bearing solutions resulting from the water-soluble copper, a point that was overlooked in the laboratory test work. Attempts to decant the copper-bearing solution for precipitation in the usual manner ahead of flotation were not satisfactory because of low water recovery (owing to poor settling characteristics of the pulp) and contamination of the copper precipitate with unsettled slime. Low copper prices in 1931 necessitated the termination of testing. With the stimulus of higher copper prices in 1937, a review was made of metallurgical

Jan 1, 1940

By T. S. Hutchinson, C. E. Kemp

The bottom water drive analysis presented by Muskat has been extended to include fields with wider well spacings. Curves are presented from which volumetric sweepout, water-oil ratio, and rate relations may be calculated. The effects of non-unity ratios on sweepout eficiency and productivity decline have been studied by an approximate method. Also, the effect of gravity on volumetric sweepout has been approximated for a particurlar geometry. INTRODUCTION The purpose of this paper is to report work done in applying the analysis of bottom water drive reservoirs given by Muskat1 to a larger class of reservoirs, to extend this analysis to include the effects of gravity and non-unity mobility ratios in an approximate manner, and to investigate the rate of decline of productive capacity. The bottom water drive type reservoir is one where the oil is underlain by a water zone of sufficient thickness that water movement is essentially vertical. This system is defined in more detail in the appendix and a one well element is shown diagrammatically in Fig. 1. Muskat obtained solutions to the equations describing the volumetric displacement efficiency of idealized bottom water drive systems by assuming that gravity effects due to differences in density betwecn oil and water were negligible and that the mobilities of oil and water were the same. If either of these assumptions is not made, the complexity of the system makes an analytical solution well nigh impossible at the present stage of mathematical development. Coles and Stade' developed an approximation to consider these factors. The authors have refined approximations, starting with the same basic assumption, which should give a somewhat quantitative picture of bottom water drive performance when mobilities are not equal and the effects of gravity are not negligible. The results of these approximate calculations can then be used to obtain the decline in well productivity as the field is depleted.

Jan 1, 1957

By H. F. Korman, M. C. C. Mow, P. K. Dai

INTRODUCTION Detonations of high explosives in soil and rock have been used frequently in civil engineering applications. Of particular interest in recent years has been the development of test methods to simulate the desired blast and shock environments for the testing of protective structures. The United States Air Force, in particular, the Air Force Weapons Laboratory, in conjunction with the Defense Atomic Support Agency, has in recent years, developed special technology for simulation testing of protective structures in soil and rock media. Such a technology, although initially developed for military applications, is rapidly finding its way into civil applications. One of the major problems in the design of the simulation test is the correct prediction of ground motion induced by the detonation of high explosives. This paper presents a useful prediction method which is developed specifically for ground motion in rock that is induced by the detonation of a buried planar array of explosive columns (See Figure 1). The technique of simulating shock environment using such an array is called the Direct Induced High Explosive Simulation Tech- nique (DIHEST). Normally, each shot hole may contain canisters of ammonium nitrate positioned at various depths, or a slurry explosive with detonators positioned along its length (See Figure 1). The depth and width of the array, the spacing of shot holes, the spacing of detonators, the degree of containment, and the charge weight are the variables which govern the induced ground motion

Jan 1, 1971