Search Documents

By R. W. Hyde, B. S. Old, S. E. Eaton

INTRODUCTION ONE of the most important problems facing the steel industry at the present time is that of maintaining at a minimum the sulphur content of many grades of steel where sulphur is known to have harmful effects on both quality and yield. The present outlook in this struggle to reduce the amount of sulphur in steel is rather gloomy since the sulphur content of the raw materials available in the United States is gradually rising, with little relief in sight. A flow sheet of sulphur in the steel process is shown in Fig I. The values used here were obtained by averaging coke oven and blast furnace data at No. 5 furnace in Cleveland and are considered typical for high top pressure practice. The sulphur evolved in the blast furnace top gas was obtained by difference and since the amount is relatively small, little significance should be attached to this particular value. From Fig I it is apparent, however, that coals used in the production of metallurgical coke represent by far the largest single source of sulphur in steelmaking. As an indication of the decrease in quality of these coals as regards sulphur content the weighed average annual sulphur analysis of the coals supplied to two different steel plants, since 1925, is plotted in Fig 2.1 The sharp rise since 1940 is strikingly apparent. Another indication of this trend is found in estimates of coking coal reserves. Thus in the case of Pittsburgh seam coals available in Allegheny, Fayette, Greene, Washington, and Westmoreland Counties in Pa. as of Jan. 1937 only 25 pct of the coal reserves would contain less than 1.50 pct sulphur after washing.2,3 Many of these lower sulphur reserves have been seriously depleted in recent years because of accelerated war demands. Still another demonstration of the increasing sulphur content of coals on a country-wide basis is found in a report by the Bureau of Mines4 which shows a steady increase in the sulphur content of coke made in the United States, It should be noted that this increase continues in spite of the wider use of coal washing in recent years. Sulphur occurs in coal in three forms, pyritic (FeS2), organic sulphur, and a small amount of sulphate sulphur (CaSO4), The sulphur is subsequently found in the coke in combination with carbonaceous material of unknown composition and as calcium and iron sulphides: In considering the general problem of sulphur elimination, the Republic Steel Corp. was interested in determining which, if either, of the two major forms of sulphur in coal contributes the greater portion of sulphur to the coke, Since the ratio of pyritic to organic sulphur varies widely in different coals, it was thought that if it could be shown definitely that the major part of the sulphur occurring in coke originates from one of the two major forms of sulphur in the coal, it would then be possible to select with confidence coal which, although high in total sulphur, would yield coke of fairly low sulphur content, Using the new

Jan 1, 1948

Sykes, W. P.-Effect of Temperature, Deformation, Grain Size, and Rate of Loading on Mechanical Properties of Metals. Discussed by Zay Jeffries, W. H. Bassett, F. E. Carter 3 Evans, Geo. Watkin.-Alaskan Coal Fields. Discussed by P. N. Moore, H. H. Stoek, G. S. Rice, H. Emerson 4 Eavenson, Howard N.-Run-off and Mine Drainage. Discussed by J. R. Campbell, Andrew B. Crichton, J. B. Warriner, R. V. Norris, H. G. Moulton, H. B. Wright 7 Andrews, Allen, and Garcia, John A.-Skip Hoisting for Coal Mines. Discussed by R. V. Norris, Geo. S. Rice, H. N. Eavenson, E. A. Holbrook, Robert Obert, Andrews Allen, T. M. Chance 12 Rice, Geo. S.-Coal-pillar Drawing Methods in Europe. Discussed by Carl Scholz, D. Harrington; H. 1. Smith 16 Knapp, Arthur.-Modified Oil .well Depletion Curves. Discussed by Roswell H. Johnson 21 Alvey, Glenn H., and Alden W. Foster.-Barrel-day Values. Discussed by Roswell H. Johnson 22 Matteson, W. G.-Secondary Intrusive Origin of Gulf Coastal Plain Salt Domes. Discussed by Eugene Coste, E. W. Shaw, Joseph E. Pogue, F. G. Clapp, E. DeGoIyer, W. G. Matteson, H. W. Hixon, R. Van A. Mills 23 Reger, David B,-Carbon Ratio of Coals in West Virginia Oil Fields. Discussed by J. T. Singewald, Jr 33

Jan 5, 1921

By AIME AIME

A DOCUMENT of progress and of great interest to engineers is the report of the Military Affairs Committee of 'the Engineering Council, which has just been accepted and sent to the secretary of War. It provides .a plan whereby civilian engineers holding commissions in the Reserve Corps may; with their con- sent, be called into service of the army during peace at any time, either with troops in the field or in a consulting capacity on any government engineering work. The Military Affairs Committee finds ample authority in the military bill passed by Congress on June 4, 1920, for this arrangement and also for extending the privilege to military engineer, officer-s of the regular army to engage in civilian work during times of peace. It is hoped that the Secretary of War will adopt the suggestions and put the program outlined into effect. This is a constructive piece of work comparable to the efforts of the military Committee before the war which developed so much in the way of preparedness, particularly in the program of military lectures which, held in the auditorium in the Engineering Societies Building, became so popular that each lecture had

Jan 1, 1920

By Donald W. Gentry

The recently established SME-AIME Education Board has completed its first full year of operation, and its six constituent committees-Accreditation, Career Guidance, Continuing Education, Educational Statistics, and Scholarship-have been extremely active in identifying and initiating programs to serve the educational needs of the Society of Mining Engineers and its members. The Continuing Education Committee-primarily concerned with the needs and problems associated with providing a continuing education program for SME members-is responsible for: (1) determining the need for short course offerings; (2) developing needed courses, along with new means and opportunities of presentation; and (3) scheduling and evaluating course presentation. In response to this charge, the committee has sponsored two short courses at the SME-AIME Fall Meeting in St. Louis and three short courses at the AIME Annual Meeting in Denver. Its major effort, however, has been directed toward the 1978 SME-AIME Fall Meeting to be held in Orlando, Fla., where 18 days of short-course instruction have been scheduled. A portion of these courses will be presented prior to the meeting, with the remainder to be presented in Nassau, Bahamas, immediately following the meeting.

Jan 7, 1978

By Gordon M. Yocom

A PROPER consideration of the subject of this paper should include economic aspects as well as the technical phases of the metallurgy, production, and properties of the product. The metallurgical phases of the processing and properties of the product will be considered only from practical aspects and within the scope of the writer's experience with tonnage production. The Bessemer process was invented 85 years ago and became important because it put steel manufacture upon a larger and less costly basis. In America the Bessemer production has declined for many years and has not maintained its proportionate place with the rapid advances of the open hearth. The achievements in the open-hearth field were attained by the greater number of technical people attracted to that branch of the industry. The antipathy of technical students for the older and less popular Bessemer field gradually weakened the forces defending it and retarded the development of new and better methods. In Europe the economic advantage of the basic Bessemer process has not been overlooked and the tonnage usually is greater than that of the open hearth. The acid process has been the subject of renewed attention in America during the past few years and those who are more familiar with it are striving to show that the method is too valuable to abandon. A considerable tonnage of Bessemer-blown metal, in both molten and ingot forms, used in connection with the open-hearth practice makes it an important auxiliary unit to the industry. This practice aids in modifying the price level of heavy remelting scrap in addition to speeding up the open-hearth operation. The use of Bessemer steel has continued not only because of periodic economic advantages but also because of certain inherent qualities of machinability, weldability and stiffness, which are valuable for many applications. The properties of stiffness and rather high reaction to cold-work require some modification in order to meet the demands of modern methods of processing, which involve cold-reduction and cold-forming. At least one factor contributing to the stiffness of this steel is the relatively high phosphorus content of the acid product. The phosphorus content of the Thomas or basic Bessemer steel of Europe is considerably lower than the normal acid product in America. The American industry has continued the use of the acid process chiefly for the reason that the available ores are more easily adapted to this process from both metallurgical and economic standpoints. In European practice the basic process is necessary with the highly phosphoric ores available and it is sustained to some degree by the sale of the rich phosphate slag as a by-product. The basic process was used in this country at several plants many years ago, but was abandoned for economic reasons. A part of the past history of these trials is given here because the author believes it has not been published and it has some bearing on the subject of this paper. The information is authentic to the extent that

Jan 1, 1941

By Augustus Locke

In 1900, when. the public first heard of "secondary enrichment," the Butte chalcocite seemed clearly supergene. Mining, through successive regions of leached capping, bonanza sulfide, and sulfide less rich, had paused at lean bottom levels which, though chalcocite-bearing, suggested the waning of copper. The deepest chalcocite, at 1500 ft., was yet too shallow to disturb the supergene hypothesis. But, with deeper mining, lean levels yielded to fat ones. Here and there they showed, within the same vein, an inverted distribution, chalcopyrite above and chalcocite below. To the miners' astonishment, they carried chal-cocite, unaffected by cross faults, on an independent course to the depth of 2500 ft. The pattern of ore distribution, hitherto revealed only in fragments, was now appearing in perspective, and, in the depth of the chalcocite, was beginning to make Butte differ from all districts where the chalcocite is indubitably supergene. The idea of hypogene origin at length came into favor; by 1913, when Sales' advocated this origin, the argument had become a powerful one. This argument rested on field evidence; but, already, there was beginning to emerge microscopic evidence not included in this argument. Especially pertinent was the proof that (1) the deep chalcocite lies in-mixed with bornite, often microscopic; (2) the deep chalcocite often replaces bornite; and (3) replacement of bornite by chalcocite is accomplished more easily than that of pyrite, enargite, or chalcopyrite. The microscopic evidence has been accumulating for ten years and it demands

Jan 1, 1924

The meeting of the Institute of Metals Division was held in Phila-delphia from Sept. 30 to Oct. 2, inclusive. On Monday evening preceding the meeting, a dinner was held at the Ritz-Carlton Hotel at which many of the former officers of the Division and of the present officers and execu-tive committee were present. The subject of a membership committee was discussed and a motion to appoint such a committee with powers to go over the membership list for the selection of divisional members and to institute plans for additional members was passed. Mr. H. E. Howe and Dr. Johnston of the National Research Council attended the meeting and presented their plans for an Alloys Research Association. Many opinions were voiced as to the practicability of such a scheme and Mr. Howe expressed himself in appreciation of the cooperative thought and efforts given him. On Tuesday morning the Institute of Metals Division joined sessions with the American Foundrymen's Association and listened to the opening addresses. In the afternoon a boat ride was taken on the Delaware River, visiting the plants of the Cramp Ship and Engine Building Co. and the shipyard of the Emergency Fleet Corpn. at Hog Island. The launching of the boat christened "Afoundria" at 5 p.m. was witnessed by members of the party. The opening technical session was held on Tuesday evening at the Ritz-Carlton Hotel at 8 o'clock. The next session was held at the Ritz-Carlton at 10 o'clock on Wednesday morning and the final session at the same time and place on Thursday morning. The sessions were well attended and the discussion was good. The highly technical nature of some of the papers on the program was of special note. Taken as a whole the meeting was one of the most successful ever held. The follow-ing papers were presented:

Jan 11, 1919

By J. F. Breedis

The morphology and crystallography of marten -site formed during quenclzing were examined by transmission electron microscopy in alloys whose compositions lie between Fe-19 wt pct Cr-11 wt pet Ni and Fe-33 wt pet Ni. Depending upon composition, four types of transformation products were observed in this portion of the Fe-Cr-Ni system. Three of these products are denoted as lath, plate, and surface martensite. The hcp structure found in association with martensite it? certain higlz-clzromium stairzless steels does not influence the transformation crystallogyaphy and cannot he Considered to act as a transitional structure in the transformation from austenite to martensite. DISTINCT changes in the characteristics of mar-tensitic transformations are produced by the partial replacement of nickel by chromium in austenitic iron alloys. Large, discrete martensite plates form in Fe-30 pct Ni, while aggregates of small crystals form in sheets parallel with (111)A austenite planes in stainless steels containing in the vicinity of 18 pct Cr and 8 pct Ni. These transformation structures are termed plate and lath martensite, respectively. In addition, an hcp structure (E) has been observed in certain high-chromium stainless steels in association with martensite. It has been suggested that the E structure acts as an intermediate step in the nucleation of martensitel-' and influences the morphology and crystallography of the final transformation product. However, this structure may be the consequence of the deformation of austenite arising from the shape distortion accompanying the transformation to bcc martensite.' An hcp stacking of atoms is produced in an fcc lattice by the introduction of an intrinsic stacking fault on alternate (111)A planes. At present, the arguments behind each explanation for the E structure are based on circumstantial evidence. This investigation seeks to determine the importance of the hcp structure to the martensitic transformation, and to examine the crystallography and morphology of the structures produced in bulk samples by quenching in alloys whose compositions lie between Fe-19 wt pct Cr-11 wt pct Ni and Fe-33 wt pct Ni. These aspects of the martensitic transformations occurring in these alloys have been studied by electron metallography and selected-area diffraction of foils examined in transmission in the electron microscope. EXPERIMENTAL METHODS The alloys have been prepared from thoroughly mixed powders of pure iron (99.6+ pct, 0.06 max pct C, 0.15 max pct N), chromium (99.9+ pct), and nickel (99.9+ pct). After sintering in an Ar-H2 atmosphere, the mixtures were melted by induction heating in recrystallized alumina boats under purified argon. The ingots were cold-rolled to 0.4-mm sheets (100 pct reduction in thickness) after the removal of at least 1.5 mm from their surfaces by grinding. Three-millimeter discs were punched from the cold-rolled sheet and annealed at 1150°C for approximately 24 hr in evacuated quartz capsules. The average grain size was 40 µ Thin foils for examination in transmission in the electron microscope were prepared from discs quenched to liquid-nitrogen temperature. A depression was first jet-machined into the center of a disc and a thin area (less than approximately 3000A in thickness) was produced at the base of the depression by electropolishing. Electron-microscope studies utilized the RCA EMU-3 and the Philips EM-100B microscopes operating at 100 kv. X-ray examination of the polycrystalline alloys was performed either in a diffractometer or in a

Jan 1, 1964

By Thomas T. Read

The cost of labor turnover in industry is so large as to justify the adoption of almost any means to bring about its reduction. Intensive study has shown that faulty methods of hiring and discharging men is the most important factor in labor turnover. Complete control over hiring and discharging by the foreman is a relic of outgrown industrial conditions; centralized hiring permits this work to be put on a scientific basis and also does away with many serious evils that cannot, otherwise be reached. Centralized hiring does not impair the authority of the foreman; he hires his men from the employment office and discharges them back to it, instead of from and to the street. The employment manager, being a direct representative of the employer, tends to restore the former relation of direct intercourse between employee and employer that was helpful in avoiding friction between them. Being a specialist,, he is able to bring special knowledge and skill to bear upon the task of selling employment in his concern to desirable workmen; he is also able to give the foreign workman the special attention he requires. Employment managers have been used for the past few years by a number of large organizations, a few of which are engaged in the mining and rnetallurgical industries. They have invariably reduced labor turnover, in some cases to as little as one-tenth of what it had been. So great a reduction is due in part to other changes made in the light of the data made available by scientific study of the labor problem. In my former paper on personnel work' I advocated the more general use of the employment manager in mining and metallurgical enterprises as a means of reducing labor turnover. The form of organization recommended seems not be to understood by all, and I have requested the privilege of explaining it at greater length, since it is perhaps the most important factor of all in personnel work, and has a vital influence on the cost sheet of every industrial enterprise.

Jan 1, 1918

By M. C. Young

The Ozark Lead Company operating facilities are located in Reynolds County at the south end of the "New Lead Belt" of southeast Missouri. Development of this wholly owned subsidiary of Kennecott Copper Corporation started in May 1964, with a six foot diameter by 1250 foot deep steel lined shaft. A 20-foot diameter, 1480 foot deep, concrete lined production shaft was collared in March 1968. Production from the facilities began that month and has reached a present average of approximately 6000 tons per day. This paper describes the fully automatic system used to hoist the lead-zinc ore from a depth of 1420 feet to the surface crushing and concentrating facilities, as well as the man and materials hoisting system which allows the lowering of large equipment into the mine. MINING Galena, sphalerite and some copper minerals are found in several mineralized zones of the relatively flat lying dolomite of the "Bonneterre formation". The mineable ore zones vary from 10 feet to 110 feet thick, from 200 feet to 1200 feet wide, and several thousands of feet on strike. Two-boom diesel-hydraulic jumbos equipped with rotary percussion drills are used for both development and production. The jumbos are used principally to open the room and pillar stopes, and a track mounted down hole drill is used to bench in areas where the ore thickness warrants. Explosives used are ANFO, dynamite, and water-jell which are detonated by electric blasting caps. Broken ore (and waste) is hauled by rubber tired transports to chuted transfer raises. Approximately every 500 feet, these raises connect the orebody to the 15 foot by 28 foot train haulage level below. Two twenty ton diesel-hydraulic locomotives haul 160 tons per trip to storage pockets which have a total storage of 1500 tons of material. From these pockets the material is fed over a 6 foot by 20 foot mechanical vibrating feeder which includes one 4 foot by 6 foot grizzly section to a 48 inch by 60 inch jaw crusher. The grizzly and crusher products are transferred horizontally 45 feet on a 48 inch conveyor belt, to one of two 750 ton storage pockets. The material can flow unimpeded into one pocket or be deflected into the second pocket by a movable rock filled hopper. LOADING POCKET The material in each storage pocket is controlled by six lengths of ship anchor chain. The upper end of the 20 foot chain is anchored behind a brow in the pocket, while the lower ends are joined by a header. The lower ends of the chains are raised by two electric powered marine barge winches using 3/4 inch cables. The crusher operator controls the raising and lowering of these chains from a console in the crusher station. The upper and lower travel of the chains is controlled by cams and limit switches on the winch drive. The winches are located within 5 feet of the shaft, and shaft water continually causes problems with the electric components. A malfunction in the upper travel switch will cause the winch to pull the chains into the cable sheave (breaking the cable or sheave), while the lower switch causes the winch to unwind too much rope. Serious consideration is being given to changing the electric motors to pneumatic, since pneumatic motors will eliminate the need of any electrics at the winches. The winches can be "bottomed out" against the sheave without damage to the cable or sheave when raising the chains, and can be allowed to "free wheel" to lower the chains. A surge pocket below the two storage pockets feeds material to two

Jan 1, 1975

By R. R. Templeton

THE year 1924 was particularly notable in the petroleum industry of California as it was a period in which extensive town-lot drilling, with attendant overproduction and allied problems, virtually ceased and the industry returned to a nearly normal condition. Nearly all major field operations were conducted by large operating and marketing companies; in contrast to 1922 and 1923 field operations, when small promotion companies set the pace and forced the large companies to follow. The outstanding features of petroleum development were: 1. The three major fields of 1923, namely Huntington Beach, Long Beach, and Santa Fe Springs, declined from a production of 13,042,939 bbl., in January, to 6,764,417 bbl., in December, a drop of nearly 52 per cent: During this period, Huntington Beach declined 35 per cent., Long Beach 42 per cent., and Santa Fe Springs 63 per cent. 2. Methods of pumping deep wells were improved in some particulars; this contributed toward sustaining the productions of these three famous fields above what was predicted. 3. Of the fields producing previous to 1924, only three increased in production to any appreciable degree, during the year, as the result of bringing in new wells. These fields are Dominguez, Torrance, and Wheeler Ridge. Dominguez, discovered in September, 1923, produced 56,851 bbl. in January and increased regularly to a production of 1,641,042 bbl. in December. Torrance increased from a production of 972,261 bbl. in January, to 1,783,670 bbl., in May, and then declined to 1,393,215 bbl. in December. Wheeler Ridge, discovered in January, 1923, produced 23,254 bbl., in January, 1924, increased to a high of 33,678 bbl., in September, and declined to 27,430 bbl. in December. 4. Nearly all the production that had been shut-in during 1923 was opened in 1924, except some wells chiefly in Coalinga, Fullerton, and Santa Maria districts. The opening up of this shut-in production, combined with the increased productions from Dominguez and Torrance, were the chief factors that held the rate of decline for the state to a gentle slope.

Jan 7, 1925

By William Plank

IN PAST YEARS, engineering educators and others have been able to study the problems relating to en-gineering education in the United States with only inadequate and, frequently, inaccurate data at their command. For the first time there is now available fairly full and accurate information on this subject, gathered and compiled by the Board of Investigation and Coordination of the Society for the Promotion of Engineering Education. This board, of which W. E. Wickenden is the director, has for the past four years been carrying out fact-finding investigations into "the objects of engineering education and the fitness of the present day curriculum," under a grant of funds from the Carnegie Corporation of New York. Twelve bulle-tins have already been published by the board and others are in the process of preparation. The studies made, thus far, have been of the various phases of engineering education in general as well as of the major branches of engineering. Within the past year. the board has completed a study of mining engi-neering education by means of a questionnaire sent to members of the Institute. A special committee, con-sisting of Charles E. Locke, Allen H. Rogers and the writer, cooperated with the board in drafting certain parts of the questionnaire and in selecting the mailing list. Similar studies have been made through the mem-bers of the four other national societies. The results of these studies have been published only in mimeo-graphed form, therefore, in order to place the data before the members of the Institute an incomplete sum-mary of the replies to the A. I. M. E. questionnaire is here given. The full report will be available for distri-bution at the annual meeting in February. The questionnaire was sent to 306 members of the Institute, a proportion about equal to the proportion of the membership of the other national societies can-vassed; 152 members replied to the questionnaire, 55 per cent of whom had received college degrees in some branch of engineering connected with the mineral in-dustry. Forty-seven educational institutions were rep-resented in the replies. Seventeen different positions were held by the members who replied, with 24 con-sulting engineers at the head of the list, 20 managers, 16 superintendents, 11 presidents, 10 professors, 6 deans, and others.

Jan 1, 1928

By Oscar A. Glaeser

MINE VENTILATION is an important factor in mine maintenance as well as having direct bearing on labor efficiency. Effective ventilation systems are costly, especially those for the deeper mines, but with intelligent direction the worth of a system is usually greater than its cost. In most mines using mechanical ventilation, and practically all deep mines, it has been found beneficial to equipment, timber, and the ground, to run the fan or fans continuously even though production has been curtailed or entirely suspended. Therefore, economies in ventilation may be overlooked when general cost reductions are necessary. The operating costs of a well-designed ventilation system should be capable of reduction during periods of curtailed or suspended operations. A mine that is ventilated by splits, or that can be sectionized, can reduce its fan-power costs considerably, and provisional divisions can sometimes be made in other mines, in which the air is ordinarily coursed through all the workings, without harmful effects.

Jan 1, 1932

By Alistair Frame

INTRODUCTION In April 1988 discussions were about to start with BP on the possibility of buying their- mineral interests, and it took a long time to arrange a deal. I will talk about RTZ without BP Minerals, look at the new RTZ with BP Minerals, discuss the outlook for metal prices, and review the problems in South Africa and develop the case against sanctions on that country. RTZAT THE END OF 1988 Late in 1987, after completing a worldwide review of our strategic thrust, we decided: 1. That the business focus would be to remain a major diversified natural resource group with interests in related industries. 2. To divest non-core and low growth businesses. 3. To develop a logical acquisition plan. 4. To emphasise organic growth and, most importantly, to enhance shareholders' wealth by capital increase and a progressive dividend policy. Subsequently, we concluded that we should sell our oil and gas business and dispose of several assets for which we saw little growth potential. The disposal programme raised some U.S.$ 1,600 million, representing a significant capital gain on our various investments. All transactions were carried out by our small Head Office staff in London, without the help of merchant banks and lawyers, and we were able to safeguard the employment of our staff in all these operations. The most interesting disposal was of our oil and gas interests. Before the 1987 strategic review, we had ambitions to develop our oil and gas interests and to become the leader in the second division of European oil companies. Our interests, which were purely in exploration and production of oil and gas, consisted of the 100% owned RTZ Oil and Gas company, and 29% of LASMO, a publicly quoted U.K. oil and gas company with extensive worldwide interests. LASMO, in turn, owned 25% of Enterprise Oil, one of the more successful of the North Sea oil exploration and production companies. Prior to the end of 1987, our intention was to acquire control of both LASMO and Enterprise. However, when we evaluated the net asset value of these two companies based on our oil price assumptions, which were pessimistic for the next five years or so, we concluded that they were both trading in the market at significant premiums. This, taken with the additional premium required for acquisition and the high cost of exploration, led us to conclude that, since funds could undoubtedly be used to better effect, we should sell our interests. Turning to the other major achievements in 1988, we commissioned, and built up to design levels in a very short period of time, the Morro do Ouro gold mine in Brazil. This mine reached its design output of 100,000 ounces of gold per year within three months of start-up, which was on time and under budget. We are now considering a possible expansion of this property. In South America, Utah International, Mitsubishi and RTZ arranged non-recourse finance, with post completion guarantees, for the giant Escondida Project in Northern Chile. Financing came from a group of banks in Japan, Germany and Finland -- the countries to which most of the concentrates will be sold -- and from the LEC. The average output of the mine for the

Jan 1, 1990

By Louis W. Huber

The Liberty tunnels extend through a very steep hill in Pittsburgh (locally called Mount Washington) for a distance of slightly over a mile. The two tunnels parallel each other and are 59 ft. apart, center to center (Fig. 1) They are for vehicular traffic, and in each there is ample space for two lines of vehicles. Northbound traffic, toward downtown Pitts- burgh, is confined to the east tunnel and southbound traffic to the west tunnel. The South Hills residential district is separated from downtown Pittsburgh by Mount Washington, a steeply rising escarpment south of and adjacent to the Monongahela River. The Mount Washington district immediately south of the Monongahela River has been reached, for many

Jan 1, 1927

By K. Sallmann

Spurred by a variety of factors, coal flotation is making headway among the preparation plants of West Germany. The author gives some statistics on German coal flotation plants and information on the properties of the feed and quality of the derived products. Types of machines and reagents used, dewatering practices, tailings disposal, and thickening operations are covered. There is special emphasis on the many-sided problems that confront German coal preparation engineers. The coal mining industry of West Germany is concentrated in three coalfields: the first on the Ruhr and the Rhein rivers, the second on the Saar river, and the third near the frontier between Germany and the Netherlands, around the towns of Aachen and Erkelenz. The total run-of-mine production of these three coalfields amounts to 736,000 tpd which come from 145 collieries. There are 121 washeries, 43 of them with a flotation plant. The total throughput of these 43 washeries is 280,000 tpd, out of which 26,000 tons (9.3 pet of the washery feed coal) are cleaned by flotation. The capacity of the individual flotation plants varies within relatively wide limits, the average being 40 tph and the capacity of the largest flotation plant being 120 tph. During the last few years, the number and size of flotation plants have been steadily increasing, although flotation must be looked upon as an expensive and rather complex cleaning process. The considerations which have led to the widespread application of flotation may be summarized as follows: 1) In making coking coal, it is seldom possible to add uncleaned fines to the coke oven charge, as their ash content is too high. If, however, the ash content of the fines is reduced to a maximum of 7 or 8 pet, they can be admixed to the washed and crushed small sizes without difficulty. This means, naturally that revenue is increased since the price of coking fines is always higher than the price for dust or uncleaned wet fines. 2) To prevent silicosis and pneumoconiosis, water infusion and spraying of the coal are practiced much more today than ever before. As a result, moisture content of run-of-mine coal has markedly increased and the washery feed coal contains more and more slurry instead of dry dust. The price of slurry, how- ever, is very low, and in many cases it is impossible to sell filtered raw slurry with a moisture content of 20 to 25 pct and, at the same time, 20 to 25 pct of ash. Reduction of the ash content of these slurries improves the possibility of dewatering them and, in this way, also enhances the marketability of this product. 3) The new severe laws and regulations against pollution of air and rivers make it necessary to de-dust coal better than in the past and to reduce the quantity of the waste water from coal preparation plants and their solids content to a minimum. 4) Even if there were no compulsory reasons to clean the fines, flotation will often lead to an increase in the overall yield. Although not the only application, it appears that the treatment of coking fines is the primary field for the flotation process in coal preparation. It must not be overlooked, however, that a series of arguments may be advanced against flotation: 1) Flotation is an expensive process because, in addition to the cleaning operation itself, the dewatering of the froth and the disposal of the tailings is very costly. 2) Operation of a flotation plant requires well trained personnel. 3) Filtered froth has about a 20 pct moisture content and, therefore, if mixed with the cleaned small coal it causes an undesirable increase in water content of the coke oven charge. For this reason it is necessary to take additional measures for dewatering washed small coal and this, of course, entails additional expense. 4) Disposal of flotation tailings involves very difficult problems, particularly in the highly industrialized regions. An investigation covering 32 flotation plants of Western Germany shows the following composition and properties of their feed:

Jan 1, 1961

By Robert F. Mehl

Jan 1, 1944

By Robert F. Mehl

Jan 1, 1944

By M. V. Nevitt

In the systems Ti-Mn-O, Ti-Fe-O, Ti-Co-O, and Ti-Ni-O the bounda.r-ies of the Ti2Ni-type phases were determined at one or more temperatures and the variation of the lattice parameter with oxygen content was determined. Densities were calculated from the lattice parameters and compared with measured density values. The: results indicate that the occurrence of the phase in these systesms can be correlated qualitatively with valency electron concentration, and that the role of oxygen is that of an electron acceptor. The lower limit of oxygen solubility appears to be determined by the valencies of Mn, Fe, Co, and Ni, while the maximum oxygen concentration coincides with the filling of the 16 (c) positions of the O 7h - Fd 3m space group. THE suggestion has been made by several investigators'" that the phases having the cubic E9,-type structure, and known as 17-carbide-type, double-carbide-type and Ti,Ni-type, are members of a family of electron compounds. This concept has been given additional support by recent work8 in which new isostructural phases involving second and third long period combinations were found, and which provided further evidence of the regularity of occurrence of the phase in terms of periodic table relationships. In this laboratory attention has been focused on the isomorphs containing titanium, zirconium, or hafnium, and the role that oxygen plays in their occurrence. In some binary systems Ti,Nitype* phases occur having the formula A,B where A is the titanium group element. Based on previous workq and the present investigation, oxygen is known to be soluble in two of these binary phases, Ti,Co and Ti2Ni. It is probable that oxygen is also soluble in the other phases of this kind. In other binary systems the Ti,Ni-type phase does not occur, but does occur in the corresponding ternary systems with oxygen .3-5 The experiments described here were performed to determine whether the occurrence and composition of certain of the Ti,Ni-type phases could be related to an electronic effect and whether oxygen's stabilizing role is exerted through an influence on the electron: atom ratio. The ternary systems Ti-Mn-O, Ti-Fe-O, n-Co-O, and Ti-Ni-O were selected for study for two reasons: First, several schemes have been proposed for first long period elements which, although not in quantitative agreement, show a generally consistent trend for the variation of valency with atomic number. Although for a transition metal the term valency is difficult to define and is generally not a constant number which can be applied to all alloys, it is usually assumed to be an index of the number of electrons per atom involved in metallic cohesion. Second, the determination of the Ti2Ni-type phase boundaries was facilitated by the fact that the phase relations in several of these ternary systems have been investigated by other workers."' EXPERIMENTAL PROCEDURE___________________ The alloys were prepared by arc melting crystal-bar titanium, reagent grade TiO, and electrolytic manganese, iron, cobalt, and nickel. Each button was remelted at least three times. The metals had a minimum purity of 99.9 pct except the nickel whose purity was 99.4 pct, the major impurity in this instance being cobalt. The preparation of the manganese alloys was attended by the customary difficulties associated with the vaporization of manganese. The technique used in this case was to add approximately 10 pct extra manganese to the original charge and to continue remelting the button until the final weight was in agreement with its intended weight. At least three alloys in each system were analyzed chemically and the results, even for the manganese alloys, were in good agreement with the intended compositions. A few additional alloys in the Ti-Mn-O system were prepared by the sintering of mixed powders in evacuated quartz tubes followed in some cases by arc melting. For annealing, the alloys were wrapped in molybdenum foil and placed in fused silica tubes containing zirconium chips. The fused silica tubes were evacuated at room temperature to a pressure of 1 x l0-6 mm of Hg and sealed. These capsules were then annealed for 72 hr at an external pressure of 5 x 10-5 mm of Hg in a vacuum furnace whose temperature could be controlled to + 1°C. The success of this procedure in avoiding significant oxygen or nitrogen pickup was indicated by the bright, ductile condition of the molybdenum foil and by the complete absence of a microscopic reaction layer on the specimens. This method did not permit rapid quenching of the specimens but in no case did metal-lographic examination indicate that a solid-state transformation had occurred on cooling. Metallo-

Jan 1, 1961

By AIME AIME

NO FEATURE of the annual meeting is considered more important at Institute headquarters than the assembly of delegates from the various local sections and divisions. There the president of the Institute and other officials may learn at first hand what the members are thinking and doing in every part of the country, and the delegates, in turn, may find that head- quarters is not a group of more or less cold-blooded New Yorkers whose primary function is to send out annual bills for $15. This year, the section and division delegates required three sessions to thresh out the matters of common interest: Monday morning and afternoon and Thursday afternoon. They were also guests of the Institute at the Directors' dinner on Tuesday night, and at the Directors' meeting afterward.

Jan 1, 1932