Search Documents

By E. H. Hamilton

THE furnace on which the following investigation was based had dimensions 48 by 160 in., and was in continuous operation during the three days of the test. The average charge consisted of PER CENT. LB. PER HOUR Bed ore?14.5?2,980 Roast from Dwight-Lloyds?44.5?9,160 Siliceous ore?3.5?720 Iron flux?2.1?430 Battery plates?0.5?103 Lime rock?23.9?4,925 Briquettes?4.0?825 Scrap iron?2.1?430 M. P. slag?4.2?865 L. P.speiss?0.7?142 Total 100.0 THE furnace on which the following investigation was based had dimensions 48 by 160 in., and was in continuous operation during the three days of the test. The average charge consisted of PER CENT. LB. PER HOUR Bed ore?14.5?2,980 Roast from Dwight-Lloyds?44.5?9,160 Siliceous ore?3.5?720 Iron flux?2.1?430 Battery plates?0.5?103 Lime rock?23.9?4,925 Briquettes?4.0?825 Scrap iron?2.1?430 M. P. slag?4.2?865 L. P.speiss?0.7?142 Total?100.0?20,580

Jan 1, 1924

By L. C. Morganroth

Magnesites are of two general classes - massive and crystalline.

Jan 1, 1915

By Arthur T. Allen

THE Kingsport formation, a part of the Knox dolomite of Ordovician age, is composed of 538 ft of dolomitc and limestone. Numerous bands, layers and nodules of chert, arenaceous and shale zones are present. The characteristics displayed by these features have been useful in mapping, prospecting and mining. Perhaps a better understanding of the origin of these zones will increase their usefulness. Introduction The presence of numerous bands, nodules, and irregular bodies of chert within the Kingsport formation in the Mascot locality has long been recognized. Oder and Miller1 mention the general characteristics, but do not deal with the chert occurrences in detail. When the occurrence of chert is studied in fresh exposures underground, a variety of characteristics is noted which has been useful in correlation and in detailing the sub-surface stratigraphy. Although the writer has no desire to enter into a controversy over the origin of chert, many observations have been made of its local characterigtics. A detailed stratigraphic section is included which shows the position of the individual horizons discussed in the following paragraphs. The term "chertification" has been adopted from Fowler and Lyden2 for use here. It refers to the replacement of lime- stone by introduced silicic acid. The writer uses it to refer to the occurrencc of introduced or original chert in limestone and dolomite. In this writing "syngenetic chert" refers to chert which has been deposited contemporaneously with the enclosing limestone or dolomite. Also, it is considered to include interstitial silica shown by chemical analysis and insoluble residues. The term "epigenetic" is applied to all chert which has been introduced after consolidation of the rocks in which it occurs, regardless of the nature of the depositing solutions. Syngenetic Chert It is the belief of the author that a large percentage of the chert found in the Kingsport formation is syngenetic. The widespread occurrence of similar nodules and bands of chert in the same horizon far from one another and far from areas of deformation or alteration of the enclosing rocks is difficult to explain by infiltration of the silica after compaction of the enclosing rocks. When chert of this type does occur near zones of movement it is likely to be involved in faulting and brecciation which indicates that it was deposited prior to deformation. Older Epigenetic Chert There are several occurrences of nodules in the Kingsport which seem to be epigenetic as pointed out in the following examples: A cherty zone occurs 26 ft above the o bed (Fig =). This is not always present but is found in the greater part of mine work-

Jan 1, 1949

By Arthur T. Allen

THE Kingsport formation, a part of the Knox dolomite of Ordovician age, is composed of 538 ft of dolomitc and limestone. Numerous bands, layers and nodules of chert, arenaceous and shale zones are present. The characteristics displayed by these features have been useful in mapping, prospecting and mining. Perhaps a better understanding of the origin of these zones will increase their usefulness. Introduction The presence of numerous bands, nodules, and irregular bodies of chert within the Kingsport formation in the Mascot locality has long been recognized. Oder and Miller1 mention the general characteristics, but do not deal with the chert occurrences in detail. When the occurrence of chert is studied in fresh exposures underground, a variety of characteristics is noted which has been useful in correlation and in detailing the sub-surface stratigraphy. Although the writer has no desire to enter into a controversy over the origin of chert, many observations have been made of its local characterigtics. A detailed stratigraphic section is included which shows the position of the individual horizons discussed in the following paragraphs. The term "chertification" has been adopted from Fowler and Lyden2 for use here. It refers to the replacement of lime- stone by introduced silicic acid. The writer uses it to refer to the occurrencc of introduced or original chert in limestone and dolomite. In this writing "syngenetic chert" refers to chert which has been deposited contemporaneously with the enclosing limestone or dolomite. Also, it is considered to include interstitial silica shown by chemical analysis and insoluble residues. The term "epigenetic" is applied to all chert which has been introduced after consolidation of the rocks in which it occurs, regardless of the nature of the depositing solutions. Syngenetic Chert It is the belief of the author that a large percentage of the chert found in the Kingsport formation is syngenetic. The widespread occurrence of similar nodules and bands of chert in the same horizon far from one another and far from areas of deformation or alteration of the enclosing rocks is difficult to explain by infiltration of the silica after compaction of the enclosing rocks. When chert of this type does occur near zones of movement it is likely to be involved in faulting and brecciation which indicates that it was deposited prior to deformation. Older Epigenetic Chert There are several occurrences of nodules in the Kingsport which seem to be epigenetic as pointed out in the following examples: A cherty zone occurs 26 ft above the o bed (Fig =). This is not always present but is found in the greater part of mine work-

Jan 1, 1949

By Michael B. Bever, John R. Anderson

Carbon may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,' the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. Earlier Data The solubility of carbon in molten pure copper is about o.oooi pct at II00°C and 0.0004 pct at 1475°C.l Various authors2""6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range r2170 to 1245°c This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By John R. Anderson, Michael B. Bever

Carbon may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,' the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. Earlier Data The solubility of carbon in molten pure copper is about o.oooi pct at II00°C and 0.0004 pct at 1475°C.l Various authors2""6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range r2170 to 1245°c This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

The cables brought the news last spring that the Institute had lost by death one of its most distinguished foreign members, Hjalmar Sjogren of Stockholm. For thirty-one years, Professor Sjogren had been one of our number. He was elected in 1891, joining the Institute at the time he was in the United States, in attendance at the Fifth International Geological Congress, which was held in Washington in the late summer of that year. Professor Sjogren was once more in America in 1906 and again in 1913, and on both of those visits his friends in New York had the welcome opportunity of extending courtesies to him. He was thus well known to a wide circle in our membership. His keen interest in the geology of iron ores brought him in touch with the many Americans who have studied them and who have been active in the important productive districts which he visited. Our Transactions contain (Vol. XXXVIII) one very important paper of seventy pages on the Geological Relations of the Scandinavian Iron Ores, which he contributed. Sten Anders Hjalmar Sjogren, to give his full baptismal name, was born June 13, 1856, and was the son of Anton Sjogren, a mining engineer, at the time in charge of the iron mines at Persberg, in the east and west iron-ore belt of central Sweden, about 160 miles west from Stockholm. The Persberg orebodies yielded magnetite and specular hematite from schists, with which limestones. were interstratified as well as the peculiar Swedish rocks called "halleflinte." The mines were also well known to collectors and students of minerals. While Hjalmar Sjogren was yet a lad, his father was advanced to the superintendency of a number of famous mining localities in this same district of Wermland. Paisberg, famous for its native lead, was one; and two others, Langban and Nordmarken, were among the most prolific sources of interesting minerals in all Sweden. In several localities, the pre-Cambrian limestones had obviously experienced the recrystallizing influences of intrusive igneous rocks and had been charged with the so-called "contact" minerals, which have found their way to the museums of the world. Anton Sjogren, the father, was a keen mineralogist and Hjalmar, the son, grew up in a favorable environment for receiving training and enthusiasms of the same sort. One is not surprised, therefore, to find Hjalmar Sjogren, in the long run, turning to mineralogy and geology as his final career.

Jan 1, 1923

The cables brought the news last spring that the Institute had lost by death one of its most distinguished foreign members, Hjalmar Sjogren of Stockholm. For thirty-one years, Professor Sjogren had been one of our number. He was elected in 1891, joining the Institute at the time he was in the United States, in attendance at the Fifth International Geological Congress, which was held in Washington in the late summer of that year. Professor Sjogren was once more in America in 1906 and again in 1913, and on both of those visits his friends in New York had the welcome opportunity of extending courtesies to him. He was thus well known to a wide circle in our membership. His keen interest in the geology of iron ores brought him in touch with the many Americans who have studied them and who have been active in the important productive districts which he visited. Our Transactions contain (Vol. XXXVIII) one very important paper of seventy pages on the Geological Relations of the Scandinavian Iron Ores, which he contributed. Sten Anders Hjalmar Sjogren, to give his full baptismal name, was born June 13, 1856, and was the son of Anton Sjogren, a mining engineer, at the time in charge of the iron mines at Persberg, in the east and west iron-ore belt of central Sweden, about 160 miles west from Stockholm. The Persberg orebodies yielded magnetite and specular hematite from schists, with which limestones. were interstratified as well as the peculiar Swedish rocks called "halleflinte." The mines were also well known to collectors and students of minerals. While Hjalmar Sjogren was yet a lad, his father was advanced to the superintendency of a number of famous mining localities in this same district of Wermland. Paisberg, famous for its native lead, was one; and two others, Langban and Nordmarken, were among the most prolific sources of interesting minerals in all Sweden. In several localities, the pre-Cambrian limestones had obviously experienced the recrystallizing influences of intrusive igneous rocks and had been charged with the so-called "contact" minerals, which have found their way to the museums of the world. Anton Sjogren, the father, was a keen mineralogist and Hjalmar, the son, grew up in a favorable environment for receiving training and enthusiasms of the same sort. One is not surprised, therefore, to find Hjalmar Sjogren, in the long run, turning to mineralogy and geology as his final career.

Jan 1, 1923

By H. R. Peiffer

Recently artin has indicated that the recovery of resistivity at 145°C following elongation of molybdenum at room temperature was the result of the annihilation of vacancies. The activation energy for this process was, according to Martin, 1.26 ev. This energy seems to be a reasonable one for the activation energy for the diffusion of vacancies in molybdenum. However, impurity atoms such as carbon, nitrogen, and oxygen4 have an activation energy for diffusion in molybdenum of the same order of magnitude (i.e., 1.45, 1.15, and 2.09 ev, respectively). Cottrell and Churchman have already correlated the return of impurity atoms to dislocations in cold-worked iron with the return of the upper and lower yield point. According to cottrel16 the diffusion of carbon atoms to dislocations results in the return of the yield point. As the carbon atoms become trapped by dislocations, Bhatia has shown that a decrease in the electrical resistivity is to be expected. Cottrell and Churchman were able to correlate experimentally the decrease in electrical resistivity with the return of the yield point. Since one would expect strain aging to occur in molybdenum, an experiment was performed to determine whether the resistivity recovery at 150°C for molybdenum cold-worked at room temperature can be correlated with the return of an upper and lower yield point. For this experiment 3/16-in. tensile bars of Climax molybdenum, 99.961 pct pure, were used. The specimens were annealed at 1000° C for 1 hr in an argon atmosphere and then were elongated up to 10 pct on a Baldwin-Lima-Hamilton FGT

Jan 1, 1959

By T. Sterry Hunt

WET processes for the extraction of copper from its ores have of late attracted much attention, especially in Europe, where the use of oupriferous iron-pyrites as a' source of sulphur prevails. These processes present an additional interest, when, as is often the case, the copper-ore's to be treated contain one or both of the precious metals, since the complete separation of these from copper, either in the dry or the moist way, is, as is well known, one of the difficult problems of metallurgy. The principal wet processes hitherto in use for the extraction of copper from its ores, may be included under three classes : I. Those in which the copper in snlphuretted ores is rendered soluble in water by calcining them, after a preliminary roasting which removes the greater part of their sulphur, with a portion of common salt, by which the copper is converted into a chloride (Long-maid and Henderson), or with sulphate of soda, by which sulphate of copper is formed (Monnier). Allied to these is the method by which a portion of the copper is got as soluble sulphate by roasting without addition, a process which is sometimes modified and rendered more complete by re-roasting the lixiviated residues with the addition of a portion of raw sulphuretted ore (Bankart). II. Those methods in which free chlorhydric or sulphuric acid is used to dissolve the copper- from oxidized or roasted ores. These, while simple and efficient, are too costly, except in certain localities where chlorhydric acid is a waste product. Related to them is the plan which consists in exposing the oxidized and moistened ores to the slow action of sulphurous acid mixed with air, by which a soluble sulphate of copper is formed. It has been proposed to decompose the solutions of sulphate or chloride of copper by sulphuretted hydrogen, thus separating the copper as sulphide, and using the liberated acid to dissolve fresh portions of oxidized copper. It is, however, the almost universal practice to throw down the copper from its solutions, however obtained, in the metallic state by the use of iron, either scrap-iron or iron-sponge; although in some instances

Jan 1, 1882

By T. Sterry Hunt

Jan 1, 1882

By Archibald Macmartin

THE Königin-Marien-Hütte is the only works in Germany where the Bessemer process is carried on by the direct method. The Besserner plant there, is arranged after the true English type, and the only resemblance to the Swedish mode of procedure is the dispensing with the use of spiegeleisen at the end of the "blow." In a new department of the establishment, started within three years, each of the converters is turned by means of a very neat and compact reversible engine, the steel shaft of which is an endless screw, which turns against the oblique cogs of a large wheel attached to the shaft of the vessel. An advantage which this arrangement possesses over the ordinary English hydraulic arrangement, is the fact that the endless screw suffices to turn the vessel, in either direction, any number of complete revolutions; while even the latest American improvements, so clearly explained to us by Mr. Holley at the opening session of this meeting, do not secure even one complete revolution without changing the angle of inclination of the hydraulic piston. In the endless screw arrangement, there being no limit to the working of the motor in either direction (no return-stroke necessary), the vessel can always, unless outside reasons demand the contrary, be turned around to any desired position by the shortest cut, whether backwards or forwards. Also, the diameter of the cog-wheel attached to the vessel can be made sufficiently great to avoid all unevenness of motion. In the old department the motive-power still continues to be hydraulic. If reports be true, the new department produces spiegelized steel, for the manufacture of all-steel rails. But the old department is still,' as from the beginning, devoted to the production by the direct method of steel for steel-headed rails. The most remarkable fact connected with this direct steel is the ease with which it welds to the iron' of the rail-packets, although no borax or other fluxing agent is used to facilitate the welding. It is very rarely that an exception occurs, and an ingot or a charge is discarded by the rail-mill. The mixture of pig-iron used for the production of this steel is melted in cupolas of very interesting construction (not to be de

Jan 1, 1874

By Russell G. Haworth

Three companies, United States Potash Company, Potash Company of America, and International Minerals and Chemical Corporation, are now operating potash mines and refineries in the Carlsbad, New Mexico, area. The three mines are located approximately twenty miles east of Carlsbad. The deposits have been found ideal for mechanized mining methods. This summary has been compiled from information made available by the three operating companies.

Jan 1, 1949

By R. S. Shoemaker, F. W. McQuiston

CARLIN GOLD MINING COMPANY 1974 Operating Data to October MINE LOCATION: 40 miles from Elko, Nevada ORE DESCRIPTION: Gold with minor amounts of mercury occurring in siltstone and carboniferous limey shales. TYPE OF MINE: Open pit ORE HAULAGE TO MILL: By trucks up to a distance of 12 mi1es MILLING CAPACITY: 2500 tons per day ORE GRADE: 0.20 oz per ton oxide ore 0.25 oz per ton carbon type ore PRODUCTS: Gold bullion 993 fineness, by product quicksilver RECOVERIES: Oxide ore 887'0 Carbon ore 83% POWER FOR GRINDING: 7 Kwh/T POWER, other than grinding: 14 Kwh/T WATER SUPPLY: Pumped from wells 2- 112 miles through 13,000 ft of 8" buried pipe 6 ft underground. Consumption 0.60 tons of new water per ton of mill feed. TAILINGS: By 10" woodstave pipe a distance of 2500 ft to mine waste filled dam. RUNNING TIME: 10 ft x 10 ft mill on oxide ore, 98% 7 ft x 8 ft mill on carbon ore, 937'0 Principal causes of lost time, power outages and problems of feeding gaseous chlorine to carbon ore agitators. LABOR, TONSIMAN SHIFT: See detailed data sheet ILL BUILDING DESCRIPTION: Framed structural steel with sandwich type walls of marine plywood, then packaged pre - fabricated insulation and outer sheeting of galvanized corrugated steel.

Jan 1, 1975

By Milton E. Jennings

On May 11, 1977, the SAMARCO 508-mm (20-in.), 396-km pipeline was placed in service. This system represents the latest thinking in slurry pipeline design and is one of the main contributors to the viability of the SAMARCO project. This paper presents the background, description, and latest information on the system's operation. Special attention is given to the handling limitations of the slurry and to the unique hardware requirements.

Jan 1, 1982

By Archiblad MacMartin

The Kunigin-Marien-Hiitte is the only works in Germany where the Bessemer process is carried on by the direct method. The Besserner plant there, is arranged after the true English type, and the only resemblance to the Swedish mode of 'procedure is the dispensing with the use of spiegeleisen at the end of the "blow." In a new department of the establishment, started within three years, each of the converters is turned by means of a very neat and compact reversible engine, the steel shaft of which is an endless screw, which turns against the oblique cogs of a large wheel attached to the shaft of the vessel. An advantage which this arrangement possesses over the ordinary English hydraulic arrangement, is the fact that the endless screw suffices to turn the vessel, in either direction, any number of complete revolutions; while even the latest American improvements, so clearly explained to us by Mr. Holley at the opening session of this meeting, do not secure even one complete revolution without changing the angle of inclination of the hydraulic piston. In the endless screw arrangement, there being no limit to the working of the motor in either direction (no return-stroke necessary), the vessel can always, unless outside reasons demand the contrary, be turned around to any desired position by the shortest cut, whether backwards or forwards. Also, the diameter of the cogwheel attached to the vessel can be made sufficiently great to avoid all unevenness of motion. In the old department the motive-power still continues to be hydraulic. If reports be true, the new department produces spiegelized steel, for the manufacture of all-steel rails. But the old department is still, as from the beginning, devoted to the production by the direct method of steel for steel-headed rails. The most remarkable fact connected with this direct steel is the ease with which it welds to the iron 'of the rail-packets, although no borax or other fluxing agent is used to facilitate the welding. It is very rarely that an exception occurs, and an ingot or a charge is discarded by the rail-mill. The mixture of pig-iron used for the production of this steel is melted in cupolas of very interesting construction (not to be de-

By F. G. Cottrell

AS previously announced, Van. H. Manning has resigned as director of the Bureau of Mines, effective June 1, to become director of research with the newly organized American Petroleum Institute. Doctor Manning has been connected with the Department of the Interior for 34 years, having been civil engineer with the Geological Survey, from 1885 to 1910, previous to his connection with the Bureau of Mines which was organized in the latter year. Doctor Manning was appointed to an administrative position in the new Bureau under Joseph A. Holmes, its first director, and on Jan. 1, 1911, was made assistant director. On Jan. 1, 1914, when Doctor Holmes had to relinquish active

Jan 1, 1920

By Walter Miller

With returning prosperous conditions in all industries, oil-refinery engineering has found opportunity for the more extensive application of improvements developed during the several years of depression. The year has brought out little of an entirely new nature, but much in wider application of previous worth-while developments. The greatest volume of work done has been in modernizing the distillation and cracking units of existing refineries, particularly by substitution of combination skimming and cracking units for older equipment, and the installation of cracking plants in smaller refineries where formerly only skimming was practiced. A number of entirely new refineries were installed during the year, two of the most important being the 20,000-bbl. refinery by the Atlantic Refining Co., at Atreco, Tex., and a 12,000-bbl. plant by the Wilshire Oil Co., at Norwalk, Calif., these two embodying some of the latest developments in cracking and treating. Total refining capacity for the United States is now reported as being something over 4,000,000 bbl. per day, but a movement is on foot looking to a complete revision of these figures, as experience has indicated not only some overstatement of capacity of equipment but that considerable equipment is included which because of obsolescence and location will probably never be run again. The 3,000,000-bbl. figure which the industry reached during the year's high consuming period required the operation of probably 95 per cent of the country's efficiently usable capacity. Cracking and Polymerization There were no new outstanding developments in the cracking field, progress being made largely in the further refinement of known principles. Improvements in furnace design and operation have been largely in permitting closer control of the heating curve through the cracking-tube system, assisting in more uniform yield and in the lessening of coke deposition, and permitting longer trouble-free operating time as well as reduction in furnace-maintenance cost. Actual operating polymerization capacity has been increased little during the year, but a number of projects have been started, some nearing completion, the production from which will be available during 1937.

Jan 1, 1937

By George J. Young

(San Francisco meeting, October, 1911.) THE nature of slimes handled in the treatment of gold- and silver-ores has been discussed in technical literature to a considerable extent. The subject of slime-filtration from the practical worker's stand-point has also received much comment, and scattered through the literature of the subject are descriptions of many slime-filtration installations. Articles of this nature serve a valuable purpose and assist materially in the design of new and the improvement of old plants. The subject of the physics of slime-filtration has been touched upon to only a slight extent. The underlying principles are worthy of more intensive study and experimentation than they have received, and the main purpose of this paper is to present the results of such study and experimental work as will serve to make clear in part at least many of the principles which control the filtration of slime. Nature of Slime. Much has bean written concerning an accurate definition of the term ? slime," but no comprehensive definition seems to be generally accepted. The reason for this is clear. A slime consists of at least three different substances, each, when separated, possessing distinctly different physical and to a certain extent chemical properties. These substances are extremely fine sand, a colloidal material which may be and generally is in a coagulated condition, and a colloidal material which is in a non-coagulated condition. Suspending a slime in a relatively large volume of water by shaking and allowing sedimentation to take place, results in the fine sand settling out with comparative rapidity, followed by the coagulated material, which settles much more slowly and finally a certain portion remains

Nov 1, 1911

By M. E. Wadsworth, J. S. Cho

Colloidal silica dissolved in aqueous suspensions of high surface area thoria was permitted to adsorb on the thoria surface. Silica in three forms was identified by means of infrared spectroscopy and characterized by Si-O vibrational modes in the 9.0 to 10.5 region. A band at 9. 1 was attributed to free unad-sorbed silica, while adsorbed silica resulted in bands of greatest absorbency at 9.4 or 10.3p, depending upon the character of the surface bonding. Size considerations, the amount of silica adsorbed, and the character of the infrared spectrum for strongly adsorbed silica has been interpreted as evidence of formation of chain or layer silica linkages on the thoria surface. Infrared spectroscopy has been used successfully in recent years for the identification of minerals and synthetic inorganic substances. Unfortunately, infrared studies of silicate minerals have not proceeded to the point that unambiguous assignments may be made for Si-O vibrational modes as affected by lattice substitutions and structures. Several investigators have presented infrared spectra of silicate minerals, 1,7 and their work has pointed to the potential value of infrared to identify minerals as well as to note the sensitivity of various Si-O modes to structural and substitutional environments. The strong infrared absorption of various Si-O vibrational modes makes the infrared method a very useful tool for the study of silica adsorbed on the surface of solids of high surface area. Spaepen et a18 studied the adsorption of silica on thoria surfaces from aqueous solutions of silicic acid up to 300°C. A general review of the application of the infrared method to the study of surface adsorption has been presented by Pliskin and Eischens.9 EXPERIMENTAL Du Pont colloidal silica, Ludox SM (16.36% SiO2) and Ludox HS (30.25% SiO2) in aqueous suspensions were used as the sources of silica for the adsorption studies. The thoria used for this study was supplied by Union Carbide Nuclear Co.* under the preparation *Chemical Technology Div., Union Carbide Nuclear Co., Oak Ridge, Tenn. . number D-16-650. It was fired from the oxalate at 650°C and had a surface area of 32.4 ± 0.6 m2 per g measured by nitrogen adsorption. The chemical analysis of the D-16 thoria in ppm was: CO3= (5500), NO3- (< 4), so4±PO4 (100), and Si (20). The Ludox silica was placed in contact with the thoria in a two-liter autoclave10 between room temperature and 250°C. Slurries were made by placing 1 g of thoria in one liter of distilled water containing various additions of the silica sol. Samples were removed from the autoclave by opening a small stainless steel valve. Extracted samples were centrifuged for 10 min and excess solution was decanted. The sample was then dried for several hours at 80°C. Infrared samples were prepared by thoroughly mixing 10 mg of the thoria with 400 mg KBr in polystyrene vials on a "Wig-L-Bug" amalgamator. Pellets were pressed under vacuum and had final dimensions of 1.2 cm diam and 1.2 mm thick. Infrared spectra were

Jan 1, 1963