Search Documents

By D. Harker, E. Epremian

The constitution of the nickel-tungsten system has been studied by a number of investigators, the most recent of which are Ellinger and Sykes.1 On the basis of metallography, electrical resistivity and hardness measurements and some X ray diffraction work, they constructed a consitution diagram (Fig 1). Ellinger and Sykes report a0 for the alpha face-centered cubic phase (nickel saturated with tungsten) as 3.66?.‡ The gamma phase (tungsten saturated with nickel) is given as body-centered cubic, but no value of a. is recorded. At 43 pct tungsten by weight (approximately 20 at. pct) a beta phase is reported, but structure and lattice parameter are not known. Primarily on the basis of metallographic evidence, they conclude that beta is a new phase and rule out the possibility of formation of a superlattice since they- observe a new phase in the microstructure. Grube and Schlecht2 report an ordering reaction in a system similar to the Ni-W (Ni-Mo) and Harker3 has shown that NirMo forms a superlattice upon the pre-existing face-centered cubic lattice of the alpha phase. Elliniger arid Sykes observed a change in the diffraction pattern of a 4.3 pct W alloy upon aging and attributed it to the formation of a new phase. Thus, there appears to be some question as to the character of the beta phase reported by Ellinger and Sykes. The purpose of the present work is to determine precisely the structure and nature of the beta phase in the Ni-w system of X ray diffraction methods. Experimental Procedure One inch diameter ingots of 43.66 pct, 40.15 pct and 34.06 pct .tungsten by weight (19.8, 17.6 and 14.1 at. pct respectively) were melted and cast under vacuum from electrolytic nickel and pure wire filament grade tungsten. The ingots were soaked for 16 hr at 1300°C in a hydrogen atmosphere furnace, then swaged at this temperature and finally drawn to 0.020 in. diam wire. Some of the bar stock was retained in 1/2 in. diam rod for hardness and metallographic studies. Wire samples for diffraction work were sealed in evacuated quartz tubes and subjected to the various solution and aging heat treatments in a hydrogen furnace. X ray photograms were taken in a Debeye-Slierrer camera using copper K radiation filtered by nickel foil. Results X RAY DIFFRACTION The lattice parameters of the alpha and gamma phases at saturation were determined by an X ray photogram of the 19.8 at. pct W alloy after solution heat treatment at a temperature well within the alpha-gamma range above the peritectoid temperature (17 hr at 1150°C—oil quenched). The alpha phase was found to be face-centeted cubic with a. of 3.594 ± 0.001?, while the gamma phase was determined as body-centered cubic with a. of 3.158 ± 0.001?. Exactly the same phases and parameters were ohtained with the 17.6 at. pct W alloy for the same solution heat treatment. Thorough analysis was made of an X ray photogram of a 19.8 at. pct alloy sample in the quenched and aged condition (solution treated 1T hr at

Jan 1, 1950

NEW YORK SECTION J. E. Johnson, Jr., Chairman Edgar Rickard, Vice Chairman. D. M. Liddell, Secretary, 7 Wall St., New York, N.Y. C. A. Bohn, Treasurer John V. N. Dorr Lewis W. Francis. The annual meeting of the New York Section was held on Wednesday, June 6, with about 40 members in attendance. The treasurer re a brief summary of-the financial statement for the year, and the secretary's report was read. These reports were ordered placed on file together with the report of the auditors for the two previous years.

Jan 8, 1917

By P. H. Metzger, D. W. Fuerstenau

The activation of sphalerite was found to occur at a much lower rate with Pb++ then with Cut++ or Ag+. To prevent activation with Pb++, the ratio [m in solution must approximate 103. An example is given illustrating how this condition is met in practice through the addition of zinc sulfate and soda ash. In selective lead-zinc flotation, the mill operator, especially the one who is concentrating a partially oxidized ore, often must add zinc sulfate and/or soda ash for effective depression of the sphalerite. In the present paper the authors show how this practice prevents the activation of sphalerite in the presence of Pb++. A number of years ago Gaudin (1) postulated that Zn++ might control the activation of sphalerite with Pb++ through competitive adsorption. However, recent experimentation has shown the activation of sphalerite with Ag+ and Cut++ to be a chemical reaction in which silver or copper ions replace zinc in the sphalerite lattice through the formation of a more insoluble sul-fide (2,3,4) Thus, if activation with Pb++ is similar to that with Ag+ or Cu t+, zinc salts should control the activation of sphalerite not through competitive adsorption but because the ratio of [zn++/Pb++] in solution regulates the extent of the chemical exchange between Zn++ and Pb++ in the solid phase. The objective of this investigation has been to study the kinetics and equilibrium conditions for the uptake of Pb++ by sphalerite and to investigate the prevention of lead activation with zinc salts. BASIC PRINCIPLES Sphalerite activation has been shown to be a replacement reaction wherein a less soluble compound is formed at the expense of the more soluble zinc sul-fide (2,3,4) For example, if sphalerite is placed in an aqueous silver nitrate solution, ZnS gives to the solution more S= than can exist together with Ag+, and hence the following reaction takes place: ZnS + 2 Ag+? Ag2 S + Zn ++; k = [zn ++]/[Ag ++]2 = 10 26 (1) Therefore, ZnS will dissolve in the presence of Ag+ and activation of sphalerite with Ag+ will proceed after monolayer coverage by solid state diffusion until equilibrium conditions are reached in the system (2, 4) Because of the large difference in the solubility of ZnS and Ag2S, zinc salts cannot affect the reaction unless a complexing agent, such as cyanide ions, is present to complex Ag+ more tightly than Zn++ . By complexing Ag+ and Zn++ in solution, the uptake of Ag+ by sphalerite can be regulated by controlling the ratio m. . Experimentally (2) it was found that the activation of sphalerite by Ag+ could be prevented through the addition of NaCN if this ratio reached a value of approximately 10 26. The mechanism of sphalerite activation with copper salts is given by the following reactions: ZnS + Cu ++ ? CuS + Zn + + ; (2) k = [Zn++]/[Cu++] = 10 11 ZnS + Cu + ? Cu2S+ Zn++; (3) Experimentally Mao (3) found that the activation of sphalerite with Cu++ or Cu + was prevented if the ratios expressed in Equations 2 and 3 were approximately l09 and l022, respectively, with cyanide ions as the deactivator. Although zinc salts do not affect the activation of sphalerite with silver or copper ions in the absence of a complexing agent, activation with lead ions theoretically can be controlled by the addition of zinc salts because of the relatively small differences between the solubility of ZnS and PbS (5). Equilibrium

Jan 1, 1961

NEW YORK SECTION ALLEN H. ROGERS, Chairman, H. C. PARMELEE, vice-chairman, FOREST RUTHERFORD, Vice-chairman, W. S. DICKSON, Secretary, 71 BROADWAY, NEW YORK, N. Y. J. E. JOHNSON, JR. F. T. RUBIDGE, Treasurer, P. G. SPILSBURY A meeting of the New York Section was held at The Machinery Club on Friday evening, Oct. 4, 1918, The Chairman, Allen H. Rogers, presiding. The CHAIRMAN.-MOST of us, I suppose, have been affected more or less by The request of The Fuel Administration that we leave our automobiles standing in The garages on Sundays. We shall all be interested in hearing about The situation that has called forth This, request, and The Oil Administrator, Mr. Requa, has kindly come from Washington to Tell us about it. MARK L. REQUA.-I am very glad To Tell you about the oil problem during This war period. The United States is supplying by far The greater part of all The petroleum products consumed in Great Britain, France and Italy. In addition To This, we have had To supply a marked increase in our domestic consumption, not only of The refined products, but of fuel oil as well. The combination has put a strain on The oil industry, which it is very difficult To meet. The oil companies, being under contract, had no option as To who should get Their oil first, and They were delivering pro rata To everybody; manufacturers of furniture were getting oil with The same regularity as Those who were making aeroplanes or munitions, and The oil companies felt that something should be done. The first order with which I had. anything To do was The priority list for The delivery of fuel oil. That list contained 12 classifications, beginning with bunker fuel and railroads, and you will realize The complexity of The situation when you hear that munitions plants are in class 11. The priority list held during The winter, but transportation became so bad, because of The number of ships that were Taken for trans-Atlantic use, that some of The oil companies were not able To deliver more Than about 60 per cent. into class 5, and nothing beyond that point. To add To the Troubles, the Tank-car mileage fell off. The average for 1917 was about 36 miles per car per day. in January, 1918, it dropped To about 8 miles, and it must have been nearly zero in The early part. of February. Because of The extremely severe winter, furthermore, pipe lines were not delivering anywhere near Their normal capacity. A new priority list has recently been promulgated, introducing a few slight changes. Natural gas has been brought under its provisions, and it has been extended To include The Pacific Coast, which was not considered necessary last winter. The situation in The gas industry is not satisfactory; it is estimated that There will be a decrease of 10 To 20 per cent. in The quantity of natural gas available This winter, as compared with last winter.

Jan 11, 1918

NEW YORK SECTION J. E. JOHNSON, JR., Chairman EDGAR RICKARD, Vice Chairman D. M. LIDDELL, Secretary, 7 Wall St., New York, N. Y. C. A. BOHN, Treasurer JOHN V. N. DORR LEWIS W.. FRANCIS The following minute was unanimously passed at a meeting of the NEW YORK SECTION AMERICAN INSTITUTE OF MINING ENGINEERS held on the evening of June 6, 1917, two regular meetings having been adjourned by unanimous consent until this date out of respect to the memory of the late Chairman of the Section. Minute The death of our beloved fellow member DR. DAVID H. BROWNE one of the foremost metallurgists and one of the most brilliant and original thinkers in the profession of mining engineers, the chairman for the past two years of this section, has caused throughout a wide circle of

Jan 9, 1917

By Roy Lindgren

SINCE the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a supe-rior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1936

By Roy A. Lindgren

Since the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a superior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1937

Plans have been completed with only details to be arranged for the first Metals Branch Conference in the Northwest. The two day meeting will be held jointly with the Industrial Minerals Div. on Friday and Saturday, May 9 and 10, 1952, at the Davenport Hotel in Spokane, Wash. For, some time the metals activities in this area have been neglected. Expansion of metal producing and fabricating industries in Washington and neighboring states has brought sufficient interest to insure the success of such a meeting. A committee has been hard at work for several months. Nonferrous extractive metallurgy men will find an extensive program in the April issue of JOURNAL OF METALS. Sessions for iron and steel producers, physical metallurgists, and educators will make the Metals Branch picture complete. Metals Branch members residing in Washington, British Columbia, Oregon, Idaho, Montana, Wyoming, Nevada, and Utah, or who can be in the Northwest at this time should make plans now to attend. A Metals Branch luncheon is planned for Friday and a dinner jointly with the Industrial Minerals Div. is planned for Saturday according to F. R. Morral, metallurgist with the metallurgical research div. of Kaiser Aluminum & Chemical Corp., P. O. Box 1451, Spokane, Wash.

Jan 1, 1952

•Mineral Development Corp. of Salt Lake City, Utah purchased the Somerset and Oliver coal mines from the Kaiser Steel Corp. The mines are located at Somerset, Colo., about 75 miles east of Grand Junction, Colo. Somerset Town, with housing for 600 persons was included in the transaction. The mines employ 115 miners and have a combined capacity of 1750 tons per day. The Minerals Development Corp. is headed by Claude P. Heiner and is controlled by Godfrey L. Cabot, Inc. of New York and Boston. The Cabot Company is a major producer of carbon black. • The Dept. of Interior has announced that the name of the Defense Minerals Administration will be changed to Defense Minerals Exploration Administration. The new name of this defense agency more nearly describes its duties, since the mineral programming, procurement and claimant functions of the former DMA have been transferred to the Defense Minerals Procurement Agency. C. O. Mittendorf, formerly acting administrator of DMA, is serving as acting administrator of the new DMEA.

Jan 1, 1952

By Carl Scholz

DURING November And December, 1907, Four Serious Mine-explosions Occurred In The Appalachian Coal-Field, Which Resulted In The Loss Of Nearly A Thousand Lives And Caused An Enormous . Damage To Property. These Accidents Attracted More Than The Usual Attention; Coal-Trade And Engineering Papers Contained Many Comments And Suggestions On The Cause And Prevention Of Accidents; The Daily Press In Many Instances Condemned The Coal-Operators And Charged These Accidents To Their Negligence, Or Their Anxiety To Make Money Without Adopting Precautionary Measures. Immediately After Each Accident The Respective State ..Authorities Ordered Close Investigations To Be Made, With The View Of Establishing The Cause And Suggesting Remedies To Prevent Recurrence. Representatives Of The Technologic Branch Of The U. S. Geological Survey, To Whom The Investigation Of Mine-Accidents Had Recently Been Delegated By The Secretary Of The Interior,. Visited The Mines And Co-Operated With The Local Authorities In Their Determinations. It May Be Safe To Say Here That An Investigation Of A Mine After An Explosion Has Occurred Discloses But Little, Because. The Causes Have Been Removed And Conditions Have Been Entirely Changed. On Jan. 8, 1905, The Coal-Operators Of West Virginia Organized An Association At Washington For The Purpose Of Making Extensive Investigations, And Sufficient Funds Were Pledged To Carry Out This Work. At This Organization Meeting, The Representatives Of The Geological Survey Present Had No Suggestions To Offer As To The Cause Of These Accidents. An Examination Of The Various Reports Concerning These Accidents Indicates That The Explosions Were Caused By The Ignition Of Gas Or Dust; They Show The Point Of Origin And The Direction In Which The Force Was Expended, And Give A Detailed Description Of The Damage Done. Very Little Has Been Said As To What

Jan 7, 1908

By Alvinus Brown Wood

THE ancient copper-mines of Lake Superior, having been destroyed or covered by-modern mining-dumps, are not accessible to the present inhabitants of that region, and, since no more are likely to be found, some account of those already discovered, from one who has seen them, may be acceptable to the Institute. Early in May, 1855, 1 took a party of men to open an ancient pit on the Quincy mine-location. Mr. C. C. Douglas was the Agent.," as mine-managers were then called on Lake Superior. The Quincy Co. had previously done work on a fissure-vein, several hundred feet west of the Amygdaloid lode (afterwards called the Pewabic lode), on which was the ancient pit herein described. It was at this pit that the Quincy' main shaft was subsequently stink. The ancient pit showed an apparent depth of about 4 ft., but when cleaned out it was shown to be 14 ft. deep, having been filled up by the sliding-in of material composed largely of broken rock, taken out in sinking the ancient shaft, and left near its mouth. Midway of the shaft, and below water-level, was found a scaffolding, of white-birch poles,- which had been used as a landing, to assist in removing the excavated rock. The shaft was 7 ft. in diameter. The excavation had been done by first building fires in order to disintegrate the rock, as was proved by the abundance of charcoal found; then breaking the softened rock with hammers of diorite, such as is found in the greenstone range on Keweenaw point. These hammers had about. the size of large paving-stones. Only broken ones were found, the whole ones having been doubtless carried away for other work, such as could be traced on the lode for a hundred feet or more to the south. At the place where this shaft was stink, barrel-copper (i.e.,

Mar 1, 1906

By Kenneth P. Katen

INTRODUCTION Though the use of continuous mining machines consolidated the operations of cutting, drilling, blasting, and loading in one machine that would theoretically provide uninterrupted production, it was soon realized that the face haulage and roof support operations remained as major impediments to continuous production. The ability to provide not only continuous cutting and loading, but also continuous haulage and roof support (see Fig. I), was the basis for the introduction of mechanized longwall systems in this country from Europe in 1951. The early systems employed friction props for roof support, but were to become obsolete shortly after introduction of the first hydraulically powered, self-advancing supports in 1960. Since then, use of the longwall technique has grown to the point where it is currently providing more than 5% of the annual output of underground coal mines in the United States. The shortwall system had its origin in Australia, but was first introduced into this country in 1962 following the development of powered roof supports. It, too, provides for continuous cutting, loading, and roof support (see Fig. 2), but has not experienced the widespread popularity of longwall due to its inherent inability to easily provide for continuous haulage. While there are in the neighborhood of 100 longwall systems currently in operation in this country, there are only a handful of short- wall operations providing production of slightly more than 907 184.7 t/a (1,000,000 stpy). Both of these systems provide uninterrupted roof support for face operations by means of hydraulically powered steel roof supports. In each case, the coal removal consists of open-end cuts made from the narrow end of a large rectangular pillar (panel) which has been blocked out by continuous miners developing entries around its perimeter. However, this is the extent of the similarities between the two systems. It is hoped

Jan 1, 1981

By F. V. Lenel, G. S. Ansell, E. C. Nelson

IRMANN'S' discovery that extrusions of fine alumi-num-flake powders possess remarkable high-temperature strengths has led to the production of a new class of engineering materials whose properties are derived from a fine dispersion of oxide particles in a metallic matrix. A fundamental study of such materials and elucidation of the mechanism whereby the oxide parti-

Jan 1, 1958

By Kenneth P. Katen

INTRODUCTION Though the use of continuous mining machines consolidated the operations of cutting, drilling, blasting, and loading in one machine that would theoretically provide uninterrupted production, it was soon realized that the face haulage and roof support operations remained as major impediments to continuous production. The ability to provide not only continuous cutting and loading, but also continuous haulage and roof support (see Fig. I), was the basis for the introduction of mechanized longwall systems in this country from Europe in 1951. The early systems employed friction props for roof support, but were to become obsolete shortly after introduction of the first hydraulically powered, self-advancing supports in 1960. Since then, use of the longwall technique has grown to the point where it is currently providing more than 5% of the annual output of underground coal mines in the United States. The shortwall system had its origin in Australia, but was first introduced into this country in 1962 following the development of powered roof supports. It, too, provides for continuous cutting, loading, and roof support (see Fig. 2), but has not experienced the widespread popularity of longwall due to its inherent inability to easily provide for continuous haulage. While there are in the neighborhood of 100 longwall systems currently in operation in this country, there are only a handful of short- wall operations providing production of slightly more than 907 184.7 t/a (1,000,000 stpy) Both of these systems provide uninterrupted roof support for face operations by means of hydraulically powered steel roof supports. In each case, the coal removal consists of open-end cuts made from the narrow end of a large rectangular pillar (panel) which has been blocked out by continuous miners developing entries around its perimeter. However, this is the extent of the similarities between the two systems. It is hoped

Jan 1, 1981

Denver, the Mile High, Queen City of the Plains, your host for AIME's 99th Annual Meeting has many exciting and picturesque places for you to visit during your stay. A host of restaurants cater to every taste; supper clubs and theaters provide nighttime entertainment; there are sports facilities and a plethora of shops for the ladies. When it comes to dining out, there are many excellent restaurants within walking distance of the Denver Hilton --among them, three in Brooks Towers: the Gitana, the Boston Half Shell serving the finest seafood, and Marvelous Mary's. In the Larimer Square area there in the Bratskellar with a true Germanic atmosphere and Sperte's Laffite offering a typical New Orleans setting.

Jan 1, 1970

SOUTHERN CALIFORNIA LOCAL .SECTION Executive Committee SEELEY W. MUDD, Chairman C. COLCOCK JONES, Vice-Chairman. FREDERICK J. H. MERRILL, Secretary-Treasurer, 631 Higgins Bldg., Los Angeles, Cal. RALPH ARNOLD A. B. CARPENTER The Southern California Section, held a dinner and meeting at. the Sierra; Madre Club, Los Angeles, on Friday evening, Sept. 28, 1915, at which 21 members and guests-were present. The Vice-Chairman, C. Colcock Jones; presided, in the absence of the Chairman. The amendment' to the By-Laws providing for the increase of the Executive Committee from five to seven members, having been formally presented at the annual meeting of June 18, 1915, and duly announced for consideration at this meeting, was voted on and unanimously adopted. Prof. Robert H. Richards of the Massachusetts Institute of Technology; made a short address on the subject of ore concentration. The paper on the Geology and Ore Deposits of Mojave, County, Arizona, prepared by F. C. Shrader, was presented to the meeting by the Secretary and was discussed by Allen Burris and Dr. L. D. Godshall. F. J. H. MERRILL, Secretary.

Jan 11, 1915

By Robert W. Hunt

The memorable features of American history have been making fast during the last century, and notably so since 1860; and they are by no means confined to political or to any one branch of scientific development. Of all the industrial arts, none show a greater change or 'a mightier progress than the Bessemer manufacture. And this year, while we are celebrating the first centennial of our national life, we can also celebrate the first decennial of American Bessemer practice. While not forgetting or undervaluing what has been done in other countries, I have thought that a brief history of the introduction and development of the Pneumatic or Bessemer process in America would be of interest. In 1863 the Kelly Pneumatic Process Company was formed and an arrangement entered into with William Kelly, who had taken out letters-patent of the United States, Nos. 16,444; 17,628, reissued as 505; 18,910, dated January loth, 1857; June 23d, 1857; November 36, 1857; and December 22d, 1867, respectively. This association mas composed of the Cambria Iron Company, E. B. Ward, Park Brothers & Co., Lyon, Shorb & Co., Z. S. Durfee, and, later, Chouteau, Harrison & Valle joined the combination. Not satisfied with possessing the control of the Kelly patent, they sent Mr. 2. S. Durfee to England, to secure for this country Mushet's patent on recarburization, No. 17,389, dated May 26th, 1857, the same having been taken out in England on September 22d, 1856. In this Mr. Durfee was successful. Previous to the application of William Kelly for a patent, Henry Bessemer, of England, had taken out patents dated February 12th, 1856, and August 25th, 1856, in this country. Kelly claimed priority in the discovery of the principles of the process, and the Patent-office allowed his claim by granting him his patents. In the autumn of 1862 Mr. Alexander L. Holley, while in England, was impressed with the importance of Mr. Bessemer's invention, and so fully foresaw its future, that, upon his return to the United States, he induced Messrs. John A. Griswold and John F. Winslow, of Troy, New York, to join him in endeavoring to possess Bessemer's American patents. Mr. Holley returned to England in

By J. D. Prater, H. R. Spedden, E. E. Malouf

With the expansion of copper leaching of the various mine wastes at the Kennecott properties, additional copper recovery facilities have been required. A research and development program has been pursued to determine a suitable economic approach to the processing of the additional leach solutions contemplated. lnvestigations on laboratory and pilot plant scales covered electrowinning, solvent extraction, launder and vat type cells, activated launders, precipitation drums, and precipitation cones. This paper contains information on the development and use of a new precipitation-cone-type copper recovery plant, which provides many advantages over older systems. The application of research findings to the old art of leaching copper from copper-bearing mine waste has resulted in a significant contribution of copper to over-all copper production. For example, at the completion of the current expansion program at the Kennecott properties in the United States, copper produced from waste dump leaching will amount to about 25% of the total production. Formerly only 2% was derived from this source. This planned expansion of copper leaching focused attention on the problem of developing more efficient methods for the recovery of copper from greatly increased volumes of copper-bearing solutions.1 The detailed investigations which have been made in laboratory pilot plant and plant tests for the recovery of copper from copper-bearing solutions have included electrowinning, solvent extraction, ion exchange and cementation with iron in launders, precipitation drums, activated launders, and precipitation cones. The results of these investigations have led to the development of a new precipitation cone-type copper recovery system providing many advantages over older methods. ELECTROWINNING OF COPPER FROM COPPER-BEARING SOLUTIONS The direct electrowinning of copper from relatively dilute solutions of copper-bearing mine water, namely solutions containing 10 to 20 lbs of copper per 1000 gal, has always been an attractive possibility.2,3 By this method, high-purity copper powder can be recovered with a power consumption of 3.5 kwh per Ib of copper. However, once the solution strength de-

Jan 1, 1967

By R. J. Wasilewski

Elastic constants have been determined on single crystals of maximum-melting-temperature NiAl compound (50.6 at. pct Al) at 25°C. Temperature variations of Young&apos;s modulus in the three principal crystal directions between -150°C and +800°C exhibit no anomalies similar to those repovted for the isomor-phous compounds brass and AuCd. It is concluded that the ordered CsCl structure is stable throughout the temperuture range investigated NICKEL aluminide is a congruently melting inter-metallic compound of CsCl (B2) structure, stable over a rather wide composition range (40 to 54 pct Al). It exhibits a lattice-parameter maximum of a. = 2.883A at 50.6 pct 1,&apos; at which composition the excess aluminum atoms are randomly distributed on the vacant nickel sites;&apos; at higher nickel compositions the excess nickel atoms replace substitutionally in aluminum sites, while at higher aluminum compositions vacancies are present in the nickel sublattice.&apos; For compositions close to NiAl no significant variation in order has been observed at temperatures up to 900°C.3 At high nickel (65 pct) compositions the existence of a martensitic structural transformation has been reported.4 NiAl is isomorphous with the ordered B-brass structure and with the high-temperature structures of AuCd and TiNi alloys close to equiatomic composition. All of these exhibit anomalous elastic behavior as the temperature of their diffusionless transformation to lower-symmetry structures is approached.&apos;-&apos; This behavior has been explained as indicative of low stability of the CsCl structure in these compounds.8 The present paper reports the experimental determination of the elastic compliances of single-crystal NiA1. EXPERIMENTAL METHOD 1) Specimens. Polycrystalline NiAl was prepared by induction melting of carbonyl nickel and high-purity aluminum and casting into solid copper molds in gettered helium atmosphere. The castings thus produced were canned in mild steel and impact-extruded at 1100 to 1200°C to 38-in.diam rod. After the steel sheath was pickled off, the rods were converted to single crystals by repeated high-frequency satisfactorily produced the desired orientations in the form of crystals 38 in. diam by 8-12 in. long. These were subsequently center less-ground to 7 to 8 mm diam by 12 cm long, electropolished (in 80 pct methanol, 20 pct HzSO, at 25°C and 15 v), and their axial orientation determined to 1 deg by the Laue back-reflection technique. The rod dimensions were determined to 0.01 mm and the densities determined from geometrical dimensions and the weight of every specimen. The average density was 5.905 0.005 g per cu cm. 2) Elastic Data Measurements. Room-temperature elastic compliances Sii were obtained by determining to 0.1 cps the fundameGtal resonance frequencies in the longitudinal and torsional vibration modes. At these frequencies the following relations hold: E =p(2lfif =pvl= Sn- 2r[Sll- S12- -£„«] g -P(2iftf = pvf = (s<« - fr(sii - sw - ±s»y where vl and vt are the velocities, and f andft the resonance frequencies of the longitudinal and torsional waves, respectively; 1 is the length of the specimen, and r is the direction cosine factor—{cos2 a • cos2 0 + cos2 a . cos2 y + cos2 0 ¦ cos2 Y}. Given three crystals of orientations (loo), (110), and (111)) i.e., F = 0, 14, and 13, we can obtain six equations for the three unknown compliances, thus providing adequate internal check. Mode mixing can readily occur in the relatively long wavelength resonance utilized here. This could cause a significant error in the torsion wave velocities calculated from the apparent resonance frequenies. Therefore, throughout the present work, a method, described previosl,&apos; was used to ensure that no significant mode mixing took place at resonance. The apparatus used was originally designed for the Elastomat, Magnaflux Corp.. Chicago, 111. determination of flexural vibration resonance frequencies. At room temperature torsional vibration mode could be established by suitable positioning of the thin wires from the input and pick-up transducers, and longitudinal mode by cementing thin magnetic foils at the ends of the specimen, and inducing the vibration by means of electromagnetic transducers. Only flex-ural resonance frequencies could, however, be obtained reproducibly over the temperature range of -150 to 800°C. These data are considerably less accurate, the error in the modulus being estimated at -0.6 pct from the specimen dimensions and the room-temperature Poisson&apos;s ratio. The reproducibility of the resonance frequencies in repeat runs was, however, to better than l in 15,000, hence the relative elastic modulus error less than 0.02 pct. Therefore, the temperature variation of the principal Young&apos;s moduli obtained by flexural resonance, relative to room-temperature values, is believed to be satisfactorily accurate.

Jan 1, 1967

By G. K. Burgess

(New York Meeting, October, 1913.) 1. COOLING AND HEATING CURVES BY G. V. BURGESS AND J. J. CROWE. § 22. THE results published in Professor Howe&apos;s paper 10 of our determinations on the Ac3 and Ar3 points for a series of commercial carbon steels 11 containing manganese in varying proportion, represent the average temperatures found by taking several (4 or 5) heating and cooling curves. The accompanying curves, Figs. 6 and 7, are, for each steel, the first heating and cooling curves as obtained by&apos; the inverse-rate method of Osmond, using a cylindrical chronograph sensitive to -0.1 sec. for recording .time. Simultaneous observations were also taken by the differential method with a platinum neutral and plotted by Rosenhain&apos;s derived differential method and gave substantially the same results, the curves having sensibly the same contours in both cases.12. The observations were taken in vacuo on cylinders 5/8 by 1 in. in length bored to center with a 1/8-in. hole to receive porcelain insulated thereto-couple, and inclosed in an out- and in-glazed Berlin porcelain tube heated electrically by, platinum foil wound on the tube. The vacuum was usually better than 0.1 mm. The heating and cooling of the furnace was automatically controlled by a salt-water rheostat with shaped electrodes, giving a uniform rate of heating and cooling.

Jan 6, 1913