Search Documents

By John J. Sammarco

The mining industry has the highest average annual fatality rate among major U.S. industries. To address this, the National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory (PRL), is conducting major research programs to reduce the hazard exposure of miners. One of the recently concluded programs at PRL developed the enabling technology for remote-controlled mining. An application involves the manual process of extracting and hauling coal where operators, in the tight confines of a mine, can be struck or caught by mobile machinery. The approach to remedy this problem uses a guidance system on the continuous haulage equipment so that it follows the continuous mining machine that extracts coal. This, in essence, involves sensor-based docking of the machines. Sensors functioning in the hostile mine environment of dust, methane gas, and water play the key role. Computer analysis of the mining machine's movements and empirical machine characterizations established operating requirements and spatial limitations to ensure proper loading of coal into the haulage equipment. These data served in the selection of a guidance sensor. Technologies such as scanning laser systems and ultrasonic sensors have frequently been used in other applications, but were found unacceptable. However, a near-infrared sensor employing active targets met the requirements. The sensor has a nominal 75b conical field of view and a range from 0.1 to 18.0 m. For the single-target mode, nominal range accuracy was 4.3% at a distance of 3.65 m. Correction algorithms were generated, which reduced the error to 0.6%. Airborne dust testing showed less than an additional0.8% accuracy (worst case) degradation at dust levels up to 15 mg/m3. Using four targets, the nominal range accuracy was 0.4% without correction algorithms. Analysis of dynamic testing of a continuous miner and haulage showed that accuracy was maintained and total target loss did not occur. A guidance system for the haulage system to follow the mining machine does not exist commercially. Such a system can reduce fatalities, injuries, and exposure to dust and noise.

Jan 11, 1998

By Steven J. Page, John A. Organiscak

Laboratory crushing experiments were conducted on a range of low- to high-volatile bituminous coals to investigate the various factors influencing airborne respirable dust (ARD) generation. This research was conducted to identify the principles of ARD liberation from the coal product. Five U.S. bituminous coals were uniformly prepared and processed through a double roll crusher located in a low-velocity wind tunnel. Experimental factors studied included inherent coal seam constituents, coal grind ability, specific energy of crushing, product size characteristics, dust cloud electrostatic field, and specific ARD generated. The results of this investigation indicate that a combination of several factors are associated with ARD generation. One factor is the effect of coal rank, described by the inherent moist fuel ratio, on the product size characteristics, defined by Schuhmann size function parameters. Another key factor is the effect of air dry loss(ADL) moisture in the coal seam on the breakage-induced electrostatic field of airborne dust. The effect of these factors is that different percentages of <10-m coal particles are dispersed as ARD. A discussion of electrostatic field principles, coal ADL, and its effect on ARD generation is presented.

Jan 10, 1998

By Anthony J. Miscoe, William M. McKewan, Richard C. Wang

The behavior of wire ropes used in hoisting is not well understood. In an effort to improve this understanding, the structure of round-strand wire ropes was analyzed. This report provides a generalized mathematical model that completely describes the geometry of the wires. It consists of two sets of vector equations and is valid for any round-strand wire rope. One set of equations is used to trace the paths of wires that have the form of a single helix; the other is used for the paths of double helical wires. The specific model for a 33-mm 6×19 Seale, independent wire rope core (IWRC), right regular lay wire rope was presented as an example. The paths and the geometric properties of the wires, which include the path length per lay of strand, the curvature, and the torsion, were determined from this model. The effects of strain deformation were analyzed, resulting in a system of equations for determining the structural parameters of the deformed rope. In future work, the model could be used to analyze wire ropes of different constructions so that a more scientifically based understanding of rope behavior can be established.

Jan 9, 1998

By Robert A. Cortese, Henry E. Perlee

Coal dust and float coal dust, produced during normal mining operations, in underground coal mines, are carried from the point of origin downstream by the ventilating air, where it deposits on the surfaces of the mine entry. In an explosion, this dust is lifted from the surfaces by the aerodynamic disturbances and, if of sufficient quantity, can continue to propagate the explosion. To prevent the surface coal dust from contributing, it must be inerted, typically by spreading pulverized limestone, i.e., rock dust, over the coal dust surface. To facilitate the dusting operation, the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory(PRL), developed an automated system that continuously monitors the accumulation of coal dust. This system could activate a rock-dusting machine that disperses rock dust into the ventilation air when dangerous deposits accumulate and deactivate the machine when sufficient inert has been deposited on top of the coal dust. The system consists of a microprocessor-controlled optical float dust deposition meter. This device measures the light intensity reflected from a deposited layer of dust. A standard cap lamp is used as a fixed-position light source. From the reflected light signal, the microprocessor determines the hazard level of the deposited layer and performs the appropriate action. Full-scale studies conducted in the Experimental Mine at PRL&apos;s Lake Lynn Laboratory, using alternating thin layers of rock dust and coal dust, successfully demonstrated the operation of the device. Based on the statistical data from these studies, a mathematical model was developed to predict long-term error in total rock dust content using this inerting procedure. Downwind dust dispersion was also examined to provide optimum placement of the dust sensors and to determine the need for better rock dust dispersion techniques.

Jan 5, 1998

The Upper Waimangaroa mining permit is part of the Buller Coalfield and lies on the eastern side of the Stockton-Denniston Plateau. The mining permit area is estimated to contain a total in-ground coal resource of 58 million tonnes, contained within 13 separate coal resource .blocks. The coal is Bituminous High Volatile B rank with export potential as semi soft coking or thermal coal. The Northern Opencast mine is the first mine proposed for Upper Waimangaroa and consists of the three resource blocks at the northern end of the permit area. The highwall of the mine will cut into the Mt William Range resulting in overburden cover of up to 150 metres in some areas. The ability to rehabilitate the area after mining was a major consideration in the design of the mine. The Northern Opencast area has been geologically mapped, extensively drilled and effectively modelled using Vulcan software. Three distinct coal seams are present and the mineable in situ resource is estimated at 8.7 million tonnes of which approximately 7.1 million tonnes is likely to be recoverable. It is proposed that this resource will be mined using opencast methods and the void will be backfilled with overburden. The life of the mine is at this stage estimated at 19 years based on an annual production of 500,000 tonnes at 1.8% sulphur and the Upper Waimangaroacoal will be blended with low sulphur coal from the Greymouth Coalfield to meet export specifications. The Northern Opencast area contains a range of native flora and fauna and physical features which make it an environmentally significant area. Mining will totally modify the area, thus an effective rehabilitation scheme is an integral part of the mine plan. Various rehabilitation methods will be used, and wherever possible, the backfilled areas will be rehabilitated so as to resemble the original area as closely as possible.

Jan 1, 1998

By Golab K, Partridge AC, Fletcher CAJ, Holtham P

Spiral concentrators are used globally in the fine coal processing industry to segregate particles, by gravitation, on the basis of density and size. Consisting of an open trough that twists vertically downwards about a central axis, a slurry mix of particles and water is fed to the top of the concentrator. Particles are then separated radially as they gravitate downward. Since their introduction to Australia in the 1940&apos;s, the generic design has evolved largely by laboratory trial-and-error investigations of different prototypes. However, this approach has proven expensive and optimal designs have not been necessarily developed. Accordingly, Computational Fluid Dynamics (CFD) analysis has been used recently as an alternative method of investigation, to assume as is envisaged, a role in the design process. To date, CFD models have progressed to simulations of turbulent fluid flow on current production spiral designs, and are continuing to be adapted for inclusion of particles at realistic feed concentrations. To be able to use the models confidently however, laboratory experiments must also be performed to validate the predictions during the development stage. This paper reports the current findings of an ongoing CFD and experimental program applied to one spiral unit. Satisfactory quantitative agreement has been achieved for the fluid and particulate flow characteristics, and although further validations are appropriate, the model already possesses significant potential for use as a reliable predictive design tool.

Jan 1, 1998

By Leigh Sharpe

Dunng the last 5 years a United Kingdom colliery has utilised a yielding-pillar configuration to extract a relatively thick coal seam at a depth of 640 m. As part of ongoing research into the siting of roadways adjacent to extracted longwall panels, seved field monitoring sites were established at differing locations to investigate roadway stability and yielding-pillar performance. Characteristic roadway deformation has been identified together with strata softening pathways which indicate the temporal increase in the height of softening into the roadway roof. In the assessment of such a complex problem numerical modelling, using FLAC, has been shown to contribute vital additional information, and provide further insights into the mechanisms controlling strata behaviour.

Jan 1, 1998

By R Frank Chiappeta, Eduardo Nixon, John Dean Smith, Tom Treleaven

"The creation of the Panama Canal was far more than a vast, unprecedented feat of engineering. It was a profoundly important historic event and a sweeping human drama not unlike that of war. Apart from wars, it represented the largest, most costly single effort ever before mounted anywhere on earth. It held the world's attention over a span of forty years. It affected the lives of tens of thousands of people at every level of society and of virtually every race and nationality. Great reputations were made and destroyed. For numbers of men and women it was the adventure of a lifetime.

Jan 1, 1998

By G. R. Harrod

Effective mine operation demands that the right people have the right information at the right time. Caterpillar&apos;s Mining and Earthmoving Technology System (METS) meets this demand by providing "real-time" information transfer between the mine offices and machines equipped with the Caterpillar Computer Aided Earthmoving System (CAES). Transfers of mine plans from the mine planning software to CAES-equipped machines give operators access to current mine plans within minutes of their creation. Additionally, office personnel have access to a current digital terrain model (DTM) of the mine site as it is updated in "real-time" by CAES-equipped machines. METS provides mine personnel in operations, planning, and management the information they need when they need it.

Jan 1, 1998

By Dong Hoon Han

The sulfation rates of magnesium oxide and calcium oxide (molar ratio 7:3) contained in calcined CMA ( calcium magnesium acetate) by SO2 were measured. The experiments were carried out in the temperature range 700 to 1100 °C and under the SO2 concentrations of 0.3 to I mol % (5 % 02). In the low-temperature range below 830 °C the reaction produced CaSO4.3MgSO4 and unreacted MgO, but no MgSO4 phase. The formation of CaSO4.3MgSO4 phase has a significant implication in that it allows the utilization of MgO for SO2 removal whereas the sulfation of MgO from conventional sources is so slow that it is of no practical interest. Thus, the calcined CMA can remove SO2 at lower temperatures than conventional SO2 absorbents and at a greater capacity. Above 950 °C only CaO reacts with SO2, but at a much greater rate than the calcined Ca(OH)2, which is one of the most reactive SO2 absorbents.

Jan 1, 1998

By A. F. Stewart

Slope design in an open pit mine includes the determination of a number of parameters, including bench height, bench face angle and berm width. By way of a case history of two highwall slopes (160m and 220m high) excavated in dipping strata in an operating coal mine, this paper illustrates the influence that bench face angle can have on the stability of an entire slope. The two highwall slopes, the lower of which experienced significant instability, were excavated in essentially the same lithologic and structural environment, with the main differences between the slopes being the angle at which the bench faces were excavated and the excavating methods that were employed. In addition to describing the instability that occurred on one of the pit walls, relevant aspects of the engineering geology, slope design and excavation procedures are described.

Jan 1, 1998

By Shillabeer J

Paste backfill has been adopted by many underground mines in North America and a growing number elsewhere. Paste offers a number of advantages. This paper suggests wider applications of paste technology to surface tailings disposal and water management. Advantages include improved overall stability, potentially easier permitting, smaller water inventory and earlier reclamation. It may be feasible to use the same plant to prepare backfill and to dispose of surplus tailings. Example cost models are given to illustrate potential applications.

Jan 1, 1998

Within ten months of the first significant intersection on the Vera deposit, approval was given to proceed with a $28.3 M underground development of the Vera-Nancy gold mine. Contrary to what the timeframe suggests, the development of the underground mine was planned in a logical and methodical manner which enabled confirmation of the resource, evaluation of the orebody for mining and sufficient production to recommence milling operations at the Pajingo treatment plant. This paper describes the underlying factors on which the project was planned and developed. The approach has successfully enabled the mine to be in production 18 months after discovery without compromising any future production or potential expansion

Jan 1, 1998

By Robin L. Simmons

Mining in the Genesis open pit has been conducted above the active haulage and ventilation declines of the Deep Star underground mine. Production has continued in both mines. The Deep Star haulage and ventilation declines, the primary and secondary egresses respectively, had to remain open and safe for travel until the new haulage and ventilation accesses were completed. Eventually, the upper 350 feet in each decline will be removed. The declines are in relatively competent calc-silicate hornfels with several high-angle, northeast-striking, clay-filled or open-spaced fault zones that create localized areas of poor ground requiring steel sets. To maintain the integrity of the declines, blast-induced vibration levels and damage were monitored in both declines after each surface blast. Seven geophones were installed in the declines to monitor peak particle velocity and peak vibration frequency. These data helped design subsequent blasts and predict expected vibration and damage levels. Blast design modifications included reducing the pattern size, reducing the powder factor and limiting blasthole detonations per delay. While limiting blast-induced vibration, these blast design modifications had to allow effective surface mining to continue. Linear regression analysis of peak particle velocity and scaled distance was used to determine the scaled distance necessary to keep the peak particle velocity under 2 inches per second. To date, the new ventilation raise, which is also the secondary escapeway, has been established and safe conditions were maintained in the original ventilation decline. Data collection and conscientious blasting procedures continue above the haulage decline.

Jan 1, 1998

By David M. Spatz

Anyone who scans the modern literature will realize that concepts of leadership have changed during the past few years. And like change in so many areas of our culture, change has been rapid in the perception of leadership. Many traditional leadership traits are still highly regarded and many of the longstanding personal qualities that improve leadership abilities continue to be effective. In the past, though, leaders could rely on dominance, intimidation and fear to accomplish their goals through the actions of others. In contrast, effective leaders today build relationships, provide vision and guidance, and strive for communication, cooperation, trust and employee satisfaction. Earnest leadership involves moral issues like honesty, integrity, fairness, empathy and respect. Modern leaders guide, facilitate and coach, rather than command and direct. But how well equipped are managers in the mining industry to meet the leadership challenges that lie ahead? More importantly, is he or she becoming a better leader? This article outlines steps to becoming a more effective leader. Management consultants stress that the changes that lie ahead will demand swift organizational adjustments and managers who are equipped to lead during times of change (Boyett and Conn, 1991; Hesselbein et al., 1996; White et al., 1996 and Kotter, 1997). Becoming a better leader begins with self-assessment and a commitment to unify all who depend on one&apos;s leadership abilities. Simply defined, leadership is leading others. Contrary to common practice, leadership is not about advancing one&apos;s own career but about bringing out the best in others. The beauty of modern leadership, however, is that the path of serving others creates synergies. They benefit everyone, including the leader, those the leader manages, upper management and company shareholders.

Jan 1, 1998

By R. H. Derammelaere

With renewed interest in coal slurry pipelines in China, Indonesia, Australia and Canada for electric generation, it appears worthwhile to update the relative economics of transporting coal by slurry pipeline. Three slurry pipeline technologies are evaluated for the commercial transportation of 3.0, 6.0, and 9.0 million tonnes per year (MMT A) example cases, over distances of 250 km, 500 km and 1000 km.

Jan 1, 1998

The efficient development and exploitation of an orebody relies on an understanding of the mineral characteristics of the deposit. This information is valuable throughout the mining cycle - during exploration, assessment, testing, design, operation and rehabilitation. Problems can arise at each stage if there is an inadequate appreciation of the mineralogy involved and its effects on the treatment process. Modern image analysis systems now permit a more quantitative understanding of the mineralogy of an ore to be gathered. Where previously the metallurgist had to rely on qualitative information to guide technical decisions, it is now possible to give numerical estimates to the compositional and textural properties which govern the mineral concentration processes. Ore samples can be characterised according to modal abundances, mineral grain size parameters and mineral associations, all of which affect the liberation and concentration of the values. The paper will discuss the application of quantitative process mineralogy by considering a number of case studies. These include: ore characterisation to assist in exploration, assessment and mine planning; modal analysis of complex mineral suites to assist in the evaluation of ores, the deportment of values between products and the recovery or loss of these values; liberation analysis for ore testing, plant optimisation and performance monitoring; and characterisation of tailing to guide estimates of leachability, stability and rehabilitation options.

Jan 1, 1998

By Jiuhua Xu, Yuling Xie, Fenglei Bie, Neng Jiang

"Abstract - The Xiaoqingling Mt. area is one of the most productive gold districts in China. The gold-bearing quartz veins are controlled by a series of east-west shear zones within the Archean Taihua Group, and related to the late Yanshanian (Cretaceous) granite. The major metallic minerals are native gold, electrum, pyrite, galena, chalcopyrite and sphalerite, with gangue minerals dominated by quartz, sericite, ankerite, and calcite. The host rocks are mainly amphibolite, plagioclase gneiss, and migmatites. Principal alteration is sericitization, silicification, pyritization, and carbonization.There are four generations of hydrothermal quartz in altered rocks of gold deposits. The earliest generation of quartz, (Q1), occurs in altered amphibolite gneiss and migmatite, and typically contains fluid inclusions with halite crystals (type A) and two phases, (L+V), of fluid inclusions (type B). The salinities of type A inclusions are 32 wt% to 52 wt%, with dissolution temperatures of halite crystals being from 155°C to 465°C. The second generation of quartz, (Q2), occurs as a fine-grained aggregate associated with sericite, and has small (less than 3 µm) type B inclusions. The third generation of quartz, (Q3), occurs in mylonitic, intensively altered rocks and specially beresite (a type of rock composed of quartz, sericite, and pyrite) near the veins, and contains large amounts of CO2-rich fluid inclusions (type C-fluid inclusions with liquid CO2 and type D-fluid inclusion with high density CO2). The CO2 contents of type C range from 72.6 to 87.4 mol% in gas phases, and 35.7 to 68.3 mol% in liquid phases, based on Laser Raman analysis. The homogenization temperatures of fluid inclusion type A and C are from 215°C to 380°C, and from 210°C to 325°C, respectively. The minimum trapping pressure of fluid inclusions is estimated as 80 MPa to 170 MPa for type A, and from 57 MPa to 190 MPa for type C, which approximate to those of fluid inclusions in vein quartz.The ?18O of quartz are from 10.4‰ to 11.0‰ for Q3 of altered rocks, and from 10.7‰ to 12.8‰ for stage I quartz. The calculated ?18O of fluid inclusions varies from -1.3‰ to 6.0‰. The ?D of fluid inclusions ranges from -67‰ to -59‰ and from -81‰ to -48 ‰, respectively. It is concluded that the water in the hydrothermal fluids both reacting with wallrocks and precipitating orebodies could have been mainly of magmatic and/or metamorphic nature. However, local meteoric water might have been important in late mineralization, because of a distinct oxygen-shift toward the meteoric water. The ?34S values for pyrite of the ores range from -7.1‰ to +7.1‰, with an average of +2.9‰. Those of other sulfides (chalcopyrite, galena, and sphalerite, range from -12.5‰ to 8.3‰. The ratios of lead isotopes for galena of the ores are: 17.06 to 17.31 (206Pb/204Pb), 15.43 to 15.74 (207Pb/204Pb) and 37.58 to 38.45 (208Pb/204Pb). In summary, ore-forming fluids in the Wenyu-Dongchuang gold deposits may have originated from a mantle and/or lower crust source, and ore materials were derived from the Precambrian basement, the Taihua Group."

Jan 1, 1998

By Katsuyama K, Nag DK

Three aspects of rock mechanics, namely, in-situ stress estimation by acoustic emission (AE) method, strength of rock mass and role of chemicals to reduce the strength are covered. It is possible to detect the previously applied maximum stress by stressing a rock specimen to the point where there is a substantial increase in AE activity. This is known as Kaiser effect. From the AE signatures in the second and subsequent loadings, AE take-off point was identified more easily than in the first loading. In determining the compressive strength of rock mass, two factors have to be considered, namely, the size effect on the compressive strength of intact rock and the effect of discontinuities on the compressive strength of rock mass. Although a modified Bieniawski criterion gives best agreement with the triaxial test data, modifications have been suggested to Hoek-Brown criterion due to its popularity. It is possible to reduce the tensile strength of sandstone by saturating it with weak chemical solutions made with dodecyltrimethyl ammonium bromide, polyethylene oxide and aluminium chloride by up to 30%. In the case of compressive strength, there is no appreciable effect. The possible explanation is that the chemical solutions produce an effect on the strength of sandstone only when the failure mechanism is dominated by tensile mode.

Jan 1, 1998

By Saskia Duyvesteyn

Small ion-exchange resin particles provide faster mass transport than conventional-sized beads. Unfortunately, high pressures are needed to pump solutions through columns containing small resin particles. It is preferable to disperse fine resins in the solution being treated. Screens have been used to separate the resin from the solution, but screens do not retain fines created by attrition of the resin particles. We have developed a separation process based on flotation, which relies on the surface characteristics of the resin, instead of size. The resin is conditioned with a surfactant before dispersing it in the solution to be treated; this increases the hydrophobicity of the resin sufficiently for froth flotation, without introducing surfactant directly into the solution. The surfactant adsorbed on the resin surface does not appear to impair the kinetics of metal ion removal. A flowsheet for an effluent treatment process is proposed; other applications are clearly possible.

Jan 1, 1998