Search Documents

By A. J. Rigby

Current practices employing porous plugs to inject nitrogen into molten copper during primary smelting are described. Nitrogen stirring increases heat transfer to the bath, eliminates temperature stratifications, and improves efficiency during the steps of desulfurization and deoxidation. The opportunity to use porous plugs as the means to introduce reducing gases to deoxidize copper is also discussed. Previously reported laboratory results using porous plugs, which point to very high utilization efficiencies of hydrogen when used as the reducing gas, are again reviewed. Advances in the design of the porous plug, and the introduction of a system enabling external replacement of plugs is also discussed.

Jan 1, 1999

By R Handfield, G Kary, Frieda Project

Recent exploration by the Cyprus Amax-Highlands Pacific-OMRD Joint Venture at the Frieda River project, PNG has demonstrated the extent of igneous phases, alteration and mineralisation, and the relationships between the various mineralisation styles in this major Cu-Au porphyry-epithermal system. The project area is in the obducted volcano-sedimentary section of the New Guinea mobile belt 78 km NE of Ok Tedi. It is between two major NNE dipping faults interpreted to have undergone thrusting then sinistral shear in the Late Miocene to Recent. The Frieda River Igneous Complex is a 15 km +7 km ovoid area with a central pod of basaltic andesite volcanics with cogenetic diorite to quartz diorite subvolcanic intrusions, and flanking clastic sediments. A series of late-stage, hornblende quartz diorite plugs ring the main igneous mass. The igneous rocks have a normal K calc-alkaline character with a very limited compositional variation. The intrusives are exposed on the eastern flank of the complex and have five mappable units and numerous defined phases. The southeastern quarter of the complex is host to a cluster of at least seven stockwork porphyry copper and skarn-hosted deposits within an area of 4.5 +3.5 km. The Horse-Ivaal and Koki deposits have identified resources totalling 804 mt @ 0.46 per cent Cu and 0.3 ppm Au, and the other deposits are in various stages of exploration. All these deposits are related to the Horse Microdiorite phase of the Complex and are outlined by a zone of potassic-propylitic-SCC alteration. Local overprinting argillic and advanced argillic alteration is related to a separate, post-porphyry mineralisation intrusive phase. The recent emphasis has been on the identification of higher-grade zones using ideas of structural control and specific intrusive-alteration-mineralisation relationships within the known resource areas. An elongate area 13 km x 4 km in the centre of the Complex has advanced argillic alteration in the volcanic rocks. This alteration zone hosts the Nena deposit (52.8 mt @ two per cent Cu and 0.7 ppm Au) and approximately 20 prospects of high sulphidation type. These deposits are distributed along two prominent NW-trending siliceous ridges interpreted as regional scale structures. Nena is a pod of vein and replacement sulphides hosted in a tectonically controlled multiphase breccia that overprints the advanced argillic alteration. The Nena deposit is 4 km from the nearest of the major porphyry occurrences. It is underlain by basemetal veins and minor porphyry mineralisation that are related to the Flimtem Trachyandesite intrusive phase. The recent search for additional Nena-type ore has focussed on the siliceous ridges using detailed structural and geochemical ore control criteria. Widespread, but poorly mineralised, basemetal-bearing carbonate and sulphate veins form a ring around the mineralised area. These veins have sericitic selvages, cut the porphyry mineralisation, but are cut by and locally underlie the silica-alunite phase of the advanced argillic alteration. The current model is that there are discrete intrusive phases responsible for each of major hydrothermal events at Frieda. These include from oldest to youngest:the Koki phase has no related alteration or mineralisation; the dominant Frieda phase has the hornfels, early skarn and minor magnetite-chalcopyrite mineralisation; the Horse phase has the bulk of porphyry copper and skarn-hosted mineralisation and minor basemetal veins; the peripheral Knob phase is barren; and the Flimtem phase has the high sulphidation epithermal deposits and minor porphyry and vein mineralisation. The intrusive phases span the interval 17 to 11.5 Ma and are co-magmatic. They represent discrete batches off the parent magma, rather than simple fractionation products.

Jan 1, 1999

By Ann E. Visser

Aqueous Biphasic Systems (ABS) form upon the admixture of certain water-soluble polymers or polymers and salts above critical concentrations, and thus represent liquid/liquid extraction systems whose nature is entirely aqueous. We are currently investigating the utility of ABS (and its solid phase analogs) as "green" alternatives to the use of volatile organic diluents in separations of metal ions. Chaotropic (water-destructuring) metal ions with small negative AGhyd (e.g., Tc04) tend to partition quantitatively to the PEG-rich phase of an ABS, but even hydrated metal cations can be partitioned to the PEG-rich phase if a suitable extractant (e.g., halide, dye, crown ether, etc.) is used to produce a more chaotropic ion-complex.

Jan 1, 1999

By D. L. Ogonowski, J. O. Marsden

The Candelaria copper-gold mine is located approximately 25 km south and east of Copiapo in Region III, Chile. The original concentrator was designed to treat 28,000 t/d (30,800 stpd) of chalcopyrite-bearing ore through a circuit consisting of a single 11.0 m(36 ft) diameter SAG mill, two ball mills, conventional rougher and scavenger flotation, column cell cleaner flotation, and ceramic disc filtration. The plant was commissioned in August 1994 and quickly reached design capacity and expected levels of metallurgical performance. In May 1996, a decision was made to double the capacity of the concentrator by the addition of a second line of equipment. The expanded facilities were commissioned in October 1997, less than 18 months after the decision to proceed, and well within the budget. The original concentrator facilities were replicated or duplicated as much as possible, however, a number of important equipment changes were made to take advantage of industry developments since the original concentrator was designed. These included the use of Eimco 120 m3 (4,200 ft3) cells for rougher and scavenger flotation and the installation of a Svedala VTM-800Vertimill for regrinding. This paper describes the rationale behind these changes and explores the reasons for the success of the project.

Jan 1, 1999

By Benjamin P. Hay

Complexation of a metal ion to a ligand often results in structural changes that introduce steric strain within the ligand. A design criterior:1 for ligands that will complex metal ions more strongly is to choose Iigar:1d architecture, that minimizes this strain. This paper describes how molecular mechanics models can be used to define the degree of ligand binding site organization in terms of' ,strain energies associated with conformational reorganization and distortion of the binding conformer. This approach yields a method to predict how modifications to ligand structure will affect metal binding affinity.

Jan 1, 1999

By Patrick G. Hill

This paper discusses safety protocols for Kiewit Construction’s Level (3) project. The Level (3) project will cover a majority of the United States, and literally thousands of site operations will be conducted over a wide geographic area under challenging conditions; rivers, roads and other features, both from the surface and often for great and from boring pits. Developing a progressive safety plan for fast-track linear projects using micro-trenching and directional boring techniques requires significant investigation, planning and evaluation. Safety protocols for inner duct installation, to be accomplished with extensive use of directional boring is an essential part of the safety plan for network construction. In light of the shear volume of work and the geographical extent of this project, in many different types of terrain, this paper will identify approaches to safety applicable to fast-track linear projects, whether surface or underground-based. Establishing a safety culture into all aspects of this operation will improve productivity and cut unnecessary expenses. This new approach involves continual improvement and evaluation of hazard analyses, inspection procedures and training.

Jan 1, 1999

By Arthur P. Sanda

Thank you Clark, for that extraordinary introduction, but Paul Harvey would be disappointed if I didn't tell you ... the rest of the story. It's true that I began my career at the Boston Traveler newspaper, one of the last of the breed that started as an office boy and eventually advanced to staff reporter. However, what the biography doesn't tell you is that after that stellar rise to prominence in the Boston financial community, the afternoon Traveler was merged into the morning Boston Herald, and I was out of a job. Between the Traveler - which I closed - and the Brockton Enterprise - where I helped bring about the first labor strike in the newspaper's 100 year history - for a short period I worked double shifts at a bomb factory where we made beanbag mines for use in Vietnam. That is until the plant blew up one morning between my shifts - my last shift, as you can guess. Incidentally, my job was quality control. Before accepting my first public relations job with Boston Gas Company - and handling the media during that companies longest strike in history - I worked part time as a police officer in the small Massachusetts town of Halifax, during which time I wrecked the town's only patrol car - twice. Having contributed all I could to Boston Gas Company, I moved on to the parent company - Eastern Gas and Fuel Associates - where I was instrumental in closing down the last remaining coke plant in the Northeast in the Bridesburg section of Philadelphia - and got my first exposure to the coal industry - a visit to Eastern's last two coal mines in western Pennsylvania, Culver and Delmont - which were closed a month later. With the coal boom at its apex in the late '70s, the bosses thought it would be safe - and safer for the other subsidiary companies - for me to be given the opportunity to establish a formal public relations department at Eastern Associated Coal Corp. In my 10 years with Eastern Associated, I was able to help take the company from 17 operating mines down to 6, from 8 longwall sections down to 5, and eventually have the entire company sold to Peabody, While at the same time, bringing an end to the coal boom. It was at this point that journalism again beckoned, which coincided with COAL magazine purchasing Coal Age from McGraw Hill Publishing. In my l l years with the magazine, we've taken it from Coal Mining and Processing, to Coal Mining, to just COAL, and back to Coal Age - which is the best thing we ever did - and we've had the company sold ... twice.

Jan 1, 1999

By G. Duncan, K. Winther, R. Ericsson

Distinct trends in grinding mill technology have emerged in recent years. In an effort to optimize overall mill performance for the needs of the End User, broad measures of logistical speed, process flexibility, operational risk, and overall costs now exert greater influence on the specification of grinding equipment. As a result, innovative alternatives to conventional grinding mill structures, supports, drives, feed, and discharge configurations are now being offered and selected with greater frequency. This paper investigates these trends in grinding mill technology, utilizing optimization and decision-theory techniques. In particular, the paper considers how specific advances in process design, product engineering, manufacturing techniques, and mining operations continue to relax technological constraints, enabling further mill innovation. In this context, a methodology is presented, illustrating how proper selection and specification of grinding mill components and configuration can target an optimization of the four End-User performance measures listed above.

Jan 1, 1999

By Peter Wells, Adrian Sabau, Turgut Yalcin

"The nickel ores of Sudbury contain substantial amounts of the gangue mineral pyrrhotite (Fe7S&) which causes certain diflculties in the milling of these ores. This paper proposes a process called “magnetoflotation” as an effective means of dealing with pyrrhotite. The method reduces the pyrrhotite content of concentrates by applying a magneticjield on the path product as it leaves the flotation cell.Successful performance of magnetoflotation requires the optimization of several variables. In this study, three of the variables (air flowrate, collector concentration, pother concentration) were investigated by Box- Wilson experimental design, and others (magnet speed, grind size, pulp density, flotation time) were examined individually. The process was tested on a Falconbridge nickel ore, assaying 1.92% Ni, and under the best operating conditions, a concentrate was obtained with 13.56% Ni grade and 74.32% recovery in a single step. Further improvements to grade and recovery were possible by cleaning and scavenging. The same ore was also tested with conventional methods for comparison, and results indicated that magnetoflotation performed better.INTRODUCTION“Magnetoflotation” refers to the process of carrying out magnetic separation and flotation simultaneously within the same device, and is intended to prevent magnetic minerals from reporting to the froth products while non-magnetic minerals are being floated. Typical cases where this method might be beneficial include the processing of magnetite and nickel ores. Its use on magnetite ores has been reported elsewhere [Yalcin, 1992; Yalcin, 19931. This paper describes its application to nickel ores, more specifically to the nickel ore of Falconbridge Limited in Sudbury."

Jan 1, 1999

By Raja V. Ramani

As the new millennium approaches, it is appropriate to assess the progress that has been made in mine health and safety, a matter of concern to management, labor and government. One can hardly look at the major events of the last century — from the birth of the US Bureau of Mines through the enactment of the modern health and safety laws — without realizing that the march has been relentless toward eradication of health and safety threats in mining. The progress is spectacular in mine safety and significant in mine health. In looking at the future, it is safe to assume that societal demands will increase for improved health and safety conditions in the workplace. So will the demands for greater technological leaps. The standards will for measuring success and the expectations of progress in creating a safer and healthier mine environment will grow. The possibilities are enormous of meeting these exacting requirements in the 21st century.

Jan 1, 1999

By Larry Stolarczyk

The mining industry would benefit greatly by imaging geologic conditions well in advance of mining. In layered deposits such as coal, trona, quartz, and potash, natural waveguides form and enable electromagnetic seam waves to travel great distances. In the early 1980s, the Radio Imaging Method (RIM) was developed to capitalize on electromagnetic seam wave propagation in the assessments of seam conditions in longwall panels. The initial applications of RIM tomography and comparisons to in-mine mapping of geologic conditions proved that faults, paleochannels, and rapidly thinning coal could be detected and imaged with seam waves. This paper describes the application of electromagnetic seam waves in mapping the margins of a paleochannel crossing a longwall panel and the interesting possibility of adopting the newly developed Full Wave Inversion Code (FWIC) )Newman 1995) to significantly improve imaging resolution. When tomography images are combined with ground control science, a significant reduction in cost, roof fall potential, and waste rock in underground mining may be realized.

Jan 1, 1999

By S S. Kanchibotla, S Morrell

In recent years there has been a growing recognition of the impact that mining practices have on the efficiency of mineral processing operations. Head grade, dilution, particle size distribution and their variability are known to have a significant effect on the throughput and recovery achieved in mineral processing plants. Improved process monitoring and modelling have provided the opportunity to identify and quantify some of these impacts and to define very significant incentives to optimise the overall operation from the mining face through subsequent comminution and processing. The Julius Kruttschnitt Mineral Research Centre has been undertaking research to optimise æMine to MillÆ performance through a major AMIRA research project and through individual research contracts with mining companies. This work has resulted in a broad range of field and laboratory experience in terms of both the challenges and the opportunities encountered when tailoring blasting operations to suit the overall æMine to MillÆ production chain. This paper describes the objectives of æMine to MillÆ blasting to optimise the system of rock breakage involved in the blasting, crushing and SAG milling of hard, brittle ores. The design of such blasts falls outside the conventional envelope of experience for most engineers and requires the consideration of some critical factors if the objectives of such blast are to be met and some of the potential problems are to be avoided. Experience to-date has also found that the quality of implementation is critical to the success of æMine to MillÆ blasts.

Jan 1, 1999

By L. Tejeda, J. R. Donald, R. Parra, J. Duran, P. H. Lauzon

"Crucible slag tests were employed to evaluate different refractory brick classes for the Cerro Matoso electric furnace. Comprehensive analysis was conducted to evaluate the crucible erosion and characterize any slag/refractory reaction products.The classes of refractories investigated were:•,tar-impregnated magnesia;•,rebonded fused grain magnesia-chrome;•,direct bonded magnesia-chrome;•,alumina-chrome;•,picrochromite; and•,magnesia-alumina (spinel).It was concluded that tar-impregnated MgO bricks were the most suitable for the slag chemistry and furnace environment according to corrosion and infiltration resistance. A picrochromite (MgCr2O4) brick performed exceptionally well with regards to erosion resistance, however, the slag infiltrated extensively through the brick pores. Alumina-chrome, direct bonded magnesia-chromite, and spinel (magnesia-alumina) bricks were evaluated as not suitable for use in the furnace."

Jan 1, 1999

By Hossein Aminian, Daniel Hodouin, Claude Bazin, Claude Jacob

"Solvent extraction followed by electrowinning (SXEW) is an economical option for the processing of low grade and oxidized copper ore. Phenomenological models were developed to simulate the copper solvent extraction and the electrowinning processes. The two models were linked together to make a SX/EW simulator. The simulator is used to predict the operation of the mines Gaspe pilot plant put in operation in 1996. Results confirm the potential of the simulation that would subsequently be used for student training, process optimization and to assess the performances of control strategies.INTRODUCTIONSolvent extraction followed by electrowinning (SXEW) has become in the last two decades a key process for the recovery of copper from solution obtained by leaching low grade copper ore. Several operations have been commissioned in North and South Americas in the last decade (Arbiter, 1994). In Canada, Gibraltar Mine (Scott, 1991) operates a SX plant followed by electrowinning (EW) to produce copper cathode from leached low-grade ore dumps. From 1996 to 1997 Mines Gaspe operated a pilot plant to test the economical feasibility of leaching an oxidized copper ore, followed by solvent extraction and electrowinning of copper. Despite copper SX/EW processes have the reputation of being low cost operations, plant engineers should always look at way to make the plant more efficient. Process models provide an economic platform to learn, control and ultimately optimize the operation of a plant.Several models have been independently proposed to simulate the SX process (Cadman and Hsu, 1970; Medina Gomez, 1980; Wilkinson and Ingham, 1983; Garcia et al., 1988; Aminian et al., 1997) and the EW process (Bryson, 1981; Barton and Scott, 1992; Barton and Scott, 1993). However few papers, if any, deal with the integration of the two process models into a single simulator of a SX-EW plant. This paper describes the development of an integrated simulator for the SX-EW process and shows some steady-state simulation runs of an actual SX-EW pilot plant. The paper consists of four sections. The first section shows the general layout and principles of operation of a SX-EW plant.The second section describes the SX model while the third section deals with the process model used for the copper electrowinning process. The last section shows how the two process models are linked to simulate the operation of the Gaspe pilot plant."

Jan 1, 1999

By C. Twigge-Molecey

All projects that are implemented, have been given corporate go-ahead on the basis of a set of clearly defined targets. These are typically a production goal at a capital cost, operating cost and production schedule, that will yield an acceptable return on investment by the companies internal criteria. The challenge for the implementation team is two-fold, firstly to properly define the project criteria prior to board approval and secondly to deliver an operating facility that meets these objectives, in particular the ROI. The paper addresses the issues a project team and the company management must address for a successful project. Key questions that will be explored are: ? What is the status of key technologies? Are they well proven in commercial practice, completely novel or in between? ? Is the project schedule driven by market constraints or cash flow constraints? ? Are the risks of fast tracking worth the potential rewards? ? For a retrofit project, are all the technical and production interfaces and issues known at the time of approval to proceed? ? How much should be invested in technological development and engineering and at which phase? ? For an owner-operator, how much responsibility is it wise or appropriate to push down to vendors? The answers to these questions for a specific project will define how you go about a project, the resources required, the contracting strategies, the phasing and the appropriate level of investment in the definition and procurement phases, prior to starting major capital commitments and construction.

Jan 1, 1999

By Kevin Beirne

Most people involved in the mining industry are familiar with student-industry co-op work-study programs. Many colleges and universities have used them for years. Northern College’s Haileybury School of Mines student co-op program adds a new dimension of productivity to the college and the mining industry. The college is located in Hailey-bury, Ontario, Canada. An example of the program’s success is the school’s relationship with Sabin Metal’s SMC (Canada) Ltd.’s McAlpine Mill in Cobalt, Ontario. Students gain practical knowledge and experience while industry gains an eager-to-learn worker. And many of the college’s advanced research services are made available to industry to supplement their own capabilities. The McAlpine Mill was established to provide custom milling of slags and ores. It also recovers metal values from other products of the primary and secondary precious metal industries.

Jan 1, 1999

By C E. Vidal

Geological exploration and mining development increased their intensity and rate of success during the last five years in Peru. Particularly relevant are the mining projects of Yanacocha and Pierina for epithermal Au and Ag. Also relevant are the new mining operations at Iscaycruz and Uchucchacua for limestone replacement Zn- or Ag-rich base metal skarn deposits. Miocene continental volcanics host the low-grade but near-surface orebodies of the Yanacocha mining district in Cajamarca. Several deposits have been mined since 1994 with open-pit and heap-leach gold production increasing from 300 000 ounces to 1 300 000 ounces in 1998. In a similar geological setting, but with three times the grade of Yanacocha, the Pierina valley-leach operation in Ancash is set to produce 800 000 ounces Au during 1999. At Iscaycruz in Lima, Cretaceous limestones host massive pyrite and sphalerite skarn deposits with 10 to 20 per cent Zn. Mining and milling were started in 1996 with last yearÆs production rising to 180 000 tonnes of Zn concentrates. At Uchucchacua, selective underground mining of fracture-controlled Ag skarns, with 400 to 420 g/t, has been recently increased from 1200 to 2000 tonnes per day to produce 5.5 million ounces Ag during 1998. Advanced exploration projects are located in the framework of nine Phanerozoic metallogenic provinces. Mineral deposits of preferred attention are precious metal disseminations and veins, base metal replacements and skarns, porphyry Cu (Mo-Au), Mississippi-Valley-type Zn and base metal volcanogenic massive sulphide deposits. Geological discovery of new orebodies enables a sustainable development of the mining industry in the country.

Jan 1, 1999

By W. M. Schafer, C. F. Luckay, D. A. King

Monitoring devices have been installed at several mine sites to assess the potential for the development of acid rock drainage (ARD) in waste rock, spent ore and tailings material. In addition, instrumentation has been designed for monitoring changes in water quality in pit lakes. These devices monitor temperature, oxygen, water movement and water chemistry in the waste rock pile. This information can be used to evaluate the current and future ARD risks and the effectiveness of caps and covers. The information can also be used in the design of other reclamation strategies that limit ARD development. The instrumentation includes nested thermistors and oxygen sensing ports, neutron access tubes, heat dissipation units (HDUs) and lysimeters. Many of the monitoring devices can be linked to a data logger and telemetry systems, enabling monitoring data to be downloaded from the office.

Jan 1, 1999

By Steven Hoerger

Newmont Mining has a large, integrated gold-mining operation in northern Nevada with several mines, stockpiles and processing facilities. There are more than 90 defined metallurgical ore types and more than 60 defined gold-recovery process options. Newmont developed a mine plan and process model to take better advantage of the available synergies at its Nevada mines. This plan includes a mixed integer and linear programming optimization tool. This system is maintained and operated by a Nevada planning group. Standard in-house planning software tools and methods have been implemented at all mine sites. These changes have allowed a reduction in mine engineering staff and have increased the effectiveness of mine planning.

Jan 1, 1999

By X Li, H Alehossein

The oscillating disc cutter (ODC) is an innovative technology for the continuous excavation of hard rock. This paper will discuss:the reasons for its development;its method of operation;current experimental results and mathematical modelling undertaken at the CMTE; andapplications in the mining and rock excavation industry.

Jan 1, 1999