Search Documents

By Fumihiko Sumiya, Yuji Ogata, Masahiro Seto, Yukio Kato, Yuji Wada, Kunihisa Utsuyama, Yoshikazu Hirosaki

It is well known that emulsion explosives can be dead-pressed especially in underground blasting. Voids in emulsion explosives will affect such malfunction of explosives. To clarify the factors that affect the dead-pressing phenomena, the characteristics of the pressure wave propagation in emulsion explosives were investigated. Three types of microballoons .or microbubbles, glass microballoons(GMB), resin microballoons(RMB) and chemical gas bubbles, were used as sensitizers for emulsion explosives. The pressure profiles inside the explosives were measured to determine the effects of the microballoons or microbubbles contained. The underwater explosion test and the large-scale drop hammer test were carried out to load the explosives with a dynamic pressure and a quasi-dynamic pressure respectively. In the underwater explosion test, the pressure profiles in the emulsion explosives were measured by a piezo-electric pressure gauge inserted to the center of the explosive cartridge which had a diameter of 30mm. In the large-scale drop hammer test, the same type of pressure gauge was placed at the bottom of the explosives. From these experiments, the following results were obtained ; A) The pressure profiles in the sample explosives sensitized by RMB or chemical gases were sharp, while in the sample explosives sensitized by GMB the profile was broad. B) The peak pressure levels in the sample explosives sensitized by RMB or chemical gases were twice as high as that in the sample explosives sensitized by GMB in the underwater explosion test. However in the large-scale drop hammer test, the amplification of the peak pressure is low compared with in the underwater explosion test. C) The impulse value was independent of the types of the microballoons or microbubbles in both tests. It was concluded that the type of the microballoons or microbubbles significantly influenced the characteristics of the pressure wave propagation in emulsion explosives.

Jan 1, 2001

By Stephen C. Tadolini

The risk of injury caused by minor roof falls continues to increase in underground mining. Most ground control injuries result from small rock falls that occur in a supported area, but do not involve the failure of the support system. In the roof, these are the "skin failures" that occur between previously installed primary or secondary bolting systems. To minimize skin failures and the associated accidents, several devices were designed and tested in the laboratory to maximize stiffness, minimize material thickness and weight, and ease material storage and handling on roof bolting machines. The goal of this project was to design and evaluate devices that can be installed with traditional primary or secondary roof supports, and that arc easy to handle/install under temporary or previously supported roof.

Jan 1, 2001

By Bill Cain, R. John Caulfield, D. Scott Kieffer

The East Bay Municipal Utility District is undertaking seismic upgrades of the Claremont Tunnel in the San Francisco Bay area. The tunnel carries treated water across the active Hayward Fault to supply a major metropolitan area. Studies indicate the tunnel could be severed by fault offset during a major seismic event. A design approach to achieve limited operation of the tunnel following fault displacement has been established and design details are currently being evaluated. This paper describes the project, the design approach, and summarizes significant construction constraints.

Jan 1, 2001

There is a significant amount of historical mining and exploration information available. This information is often distributed throughout a number of reports or plans, available from a variety of sources, and in many differing formats. The ability to capture paper-based historical information in a modem digital format provides mining and exploration companies with valuable information that can be used in a number of ways; for example, reassessments of exploration or mining work previously undertaken, or used in conjunction with current exploration information.   The purpose of this paper is threefold. Firstly, to present the paper-based historical information; highlighting some of the problems encountered, solutions to those problems, and any assumptions used. Secondly, to present the historical data in digital format, and demonstrate the tools available to analyse geological and associated information, and finally, to illustrate some of the potential future applications of the information, including mining optimisation, mine design and scheduling.   The Glenorchy scheelite/gold prospect has been used as an example. Within the overall prospect two smaller areas were selected. The Mount McIntosh and surrounding areas, focuses on exploration and surface excavation information. The Mount Judah area (State and Kelly-Taylor workings) focuses on underground mining and exploration information.  

Jan 1, 2001

By Phil D. Newman, Robert J. Pine, Kevin Ross

The Stratoni Operations in northeastern Greece rely on a selective backfill method to exploit high-grade lead-zinc deposits. Underhand cut and fill often results in spans approaching 6-9 m (depending on the mining method employed) and a competent backfill is required to avoid dilution problems. Cement consumption represents a significant mining cost and through improving the control of the backfill batch preparation, the cement content could be greatly reduced without jeopardizing the grade control. A new distribution system was installed and a QAIQC system designed in cooperation with the operators to allow a wide range of backfill recipes, providing cost savings to the mine. A review of possible failure modes and the consequent strength required for the chosen mining method was also completed and indicated potentially significant cement content reductions. The calculations are supported by 12 years of experience at the mines which provides a valuable insight into the applicability of the approach developed.

Jan 1, 2001

By W Whiten

The determination of mineral composition is necessary in the mineral sands industry. Tiwest has developed a procedure for safe and convenient determination of the mineral composition using a magnetic separation followed by chemical analysis using X-ray fluorescence spectroscopy. This then requires the conversion of the elemental assays to mineral compositions. A project at the Julius Kruttschnitt Mineral Research Centre has developed a convenient analysis method for this conversion. This analysis is based on a reconciliation of the of the assays of the sample with the standard mineral assays by making minimal adjustments based on the assay accuracies to both sets of assays. As well as providing the mineral composition it to be tested for other applications and variations of the procedure to be evaluated. Given a range of samples, testing for the accuracy of the assays of the standard minerals, has been demonstrated.

Jan 1, 2001

By Steve Dillingham

Here in the United States, as well as around the world, pose a daily dilemma - to wash or not to wash. Let’s face it, all trucks, especially our industry work horses - bulk trucks - get dirty. We all know that these units can be very expensive and washing them keeps your business investment looking new, improves public relations, fuels company pride, and facilitates equipment safety and preventative maintenance inspections.

Jan 1, 2001

By Andy Cole, Ken Thomas, Stephen Durn, Jacques McMullen

"The roasting and gas handling circuits of the Barrick Gold’s new Roasting Facility at the Goldstrike Mine in Nevada, USA incorporate well proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available technologies from the perspective of capital, environment and operating costs.Product from the up-stream dry grinding circuit requires roasting to maximize gold recovery. The roaster utilizes Freeport-McMoRan whole ore roasting technology with pure oxygen as the oxidizing gas. This process was chosen based on its proven application on Carlin-type “double refractory” ores. Double refractory is indicative of the gold being difficult to direct leach due to a combination of pyrite encapsulation and the carbonaceous preg-robbing of the ore.A very extensive gas cleaning train follows the roaster and comprises direct cooling, dust scrubbing, indirect cooling, wet electrostatic precipitation, mercury scrubbing, SO2 scrubbing, CO incineration and NO, reduction before venting to the atmosphere.The roasted calcine is quenched, neutralized and then thickened before leaching in the carbon-in-leach-circuit.INTRODUCTIONBarrick’s strategic development plan integrated the production of gold from Goldstrike’s carbonaceous ore reserves by 2000. A due diligence review of carbonaceous ore processing options was initiated during the second half of 1 996. Processes considered included autoclaving followed by a proprietary ammonium thiosulfate leaching process, fine grinding/autoclaving as practiced then by Santa Fe, and whole ore roasting as practiced by then Independence Mining and Newmont. The objective by year-end was to recommend the most robust and economical process for Goldstrike’s carbonaceous resources. In the fall of 1996, a detailed review of roasting as a processing alternative for Goldstrike was initiated."

Jan 1, 2001

By Ken Mathers, Tom Conley, Jim Rozek

The Melbourne City Link Tunnels have been constructed through a BOOT process, the largest undertaking in Australia to date. Tolling commenced on the 1.6 kilometer Domain tunnel in April 2000, and the 3.4 kilometer Burnley tunnel December 2000. The project was delivered by design construct contracting and under ISO 9000. There were a number of major challenges in completing the tunnels, including much higher than expected groundwater infiltration, hydrostatic pressures greater than 6 bar, and unique design and construction applications required to prepare the tunnels for service. This paper covers the end play and final delivery of the tunnels.

Jan 1, 2001

By Leonard Harris, Rosa H. Harris

An important part of doing business today in the mining industry, especially overseas, involves community assistance programs for the people who live around the mining areas. The purpose of such a program is to build mutual cooperation and respect that will allow the company and its neighbors to live and work in peace. To do this, it is necessary to form associations or foundations and work in a joint venture fashion. The authors discuss in some detail the outline for setting up such programs and the important role that women, in particular, can play in them.

Jan 1, 2001

By W. G. Davenport

Chapters 7,8and 9 calculated three combinations of: blast composition (mass% O2, mass% N2) oil quantity per tonne of concentrate blast temperature that will steadily produce molten 65% Cu matte from pure chalcopyrite-concentrate. The combinations are:

Jan 1, 2001

By S S. Kanchibotla, I Brunton

Most blast fragmentation models assume the rock mass properties, explosive properties and blast design variables to be constants and uniformly distributed within a blast. However, in reality all these input variables vary within a blast resulting in variation in the resulting fragmentation size distribution. A stochastic modelling approach is introduced in this paper to quantify this variation. This technique takes the input variables as statistical distributions rather than constants and through several thousand iterations, generates a statistical representation of the expected fragmentation resulting from a production blast. A case study of three production blasts from a large open pit mine are presented and the modelled fragmentation æenvelopeÆ shows good agreement with the fragmentation æenvelopeÆ estimated from Split image analysis. The various blast-related parameters influence different parts of the fragmentation distribution, eg rock strength and explosive velocity of detonation have most impact on the fines. The technique is used to identify the parameters that have the greatest influence on various size fractions. Such an analysis will be useful to direct resources to efficiently minimise the variation.

Jan 1, 2001

By R K. A Taylor

The growth in production of beneficiated ilmenite products has been one of the most significant trends in the titanium feedstock industry over the past 30 years. In this period, the production of titanium slag and synthetic rutile has grown five-fold to the point where these products represented 56 per cent of total feedstock production in 2000. Additional production capacity is being proposed as the core component of new feedstock supply projects presently under consideration. A high proportion of these products is based on technologies for which the inherent quality of the is an essential factor. Location specific factors also play a large part in determining the cost of production. As the demand for such products grows, and the availability of favourably located sources of ilmenite of suitable quality declines, it can be expected that existing beneficiation technologies will become increasingly constrained. Existing beneficiation technologies, and those which have been developed, but are not yet commercially applied, are reviewed. Future issues which are likely to impact on the cost effectiveness of these technologies, or the quality of final products, are identified. These factors suggest directions for development of ilmenite beneficiation technologies to achieve economic production of the quality of feedstocks which will be demanded by the TiO2 pigment industry in the future.

Jan 1, 2001

By M. Karmis, S. K. Weisiger

The traditional method for training personnel in the mining and other heavy industries has been face-to-face, either via a lecturer in a classroom or through an apprenticeship. With the advent of applications tools such as video, computers, and the Internet, however, a much broader range of training delivery methods is available. Especially exciting are the broad capabilities of multimedia packages that combine the best features of numerous delivery methods. Applying multimedia environments in training holds great potential, especially when there is considerable difficulty in reconstructing real training environments. The authors discuss various delivery methods currently used in training employees, including perceived advantages and disadvantages of those methods. The authors then discuss and evaluate current computer-based training efforts of the mining industry and present an example of a multimedia training tool.

Jan 1, 2001

By J. M. Mutmansky

This paper outlines the results of a study of opinions of practicing engineers concerning the value of environmental engineering courses in a mining engineering curriculum. One hundred engineers with significant experience in mining-related engineering work were carefully chosen. Of the sixty-seven responses received, about half were from mining engineers and half from environmental engineers. The results of the survey are outlined in detail. The number and type of courses recommended by the respondents are summarized as well as the specific topics recommended for inclusion in a mining engineering curriculum. The survey form also asked for the stages in the mine life when environmental experts were needed and the percentage of environmental engineering performed by outside experts for many mining-related environmental tasks. The results of this line of questions are provided. Finally, the paper offers a comparison of the results for environmental engineers and mining engineers and analyzes the differences.

Jan 1, 2001

By M. Li, J. D. Miller

Many technology problems must be solved if we are to continue to produce phosphate at our current rate of consumption. The U.S. produces at least 25% of the world's phosphate, 40 million tons of phosphate rock per annum with most of the production coming from Florida. Of particular concern are improved separation efficiency and the ability to treat new dolomitic resources. Phosphate flotation technology needs include: 1. Simplification of the standard flowsheet 2. Improved recovery of coarse phosphate 3. Selective flotation for phosphate recovery from dolomitic resources Preliminary results, including tests on plant feed from Florida show that these objectives may be achieved with a new collector chemistry depending on the specific circumstances. The effectiveness of the new collector chemistry has been demonstrated by the preliminary results from single stage flotation experiments both at the University of Utah laboratories and at Florida Institute of Phosphate Research (FIPR) laboratories. In the best case, from these experiments with low grade (5% P2O5) coarse feed (16x35 mesh), a single stage phosphate recovery of 95 % was achieved with a concentrate grade of 31 % P2O5. Such a separation efficiency could not be achieved using the traditional fatty acid/fuel oil collector. Based on these results it seems that a one step process may be possible for phosphate flotation and a research program is justified for the development of this new flotation strategy.

Jan 1, 2001

Profiled here are the eight RMCMI 2001 Scholarship Award winners. Seven of the eight attended the 97th Regular Meeting and Convention at the Steamboat Springs Sheraton Resort in Steamboat Springs, Colorado in lace June. Each spoke during the Scholarship Awards Monday luncheon and shared their goals with attendees. Thanks to the Patrons of the Institute each student received a 52,000 tuition credit, a plaque signifying the honor and the opportunity to thank the membership. The winners were guests of the Institute Sunday through Tuesday noon and had an outstanding opportunity to meet many in the coal industry that could be potential employers. The state vice presidents host the winners anti pay for their travel and hotel expenses. This is a continuing scholarship and may be renewed for tuition credit again in the senior year it the winner is a full time student and is recommended by the dean of the college or university. A resident from each of the eight member RMCMI states is selected by the Scholarship committee from Board approved institutions. Criterion for the awards is chat the recipient be (1) a full time sophomore student who will use the tuition credit in the junior year. (2) a U. S. citizen and a legal resident of the member state. (3) in good academic standing while pursuing a degree in a mining related field. They must have an expressed interest in western coal as a possible career path. Contributions to this worthwhile project are tax deductible to each individual RMCMI member or his company. Through donations of 5100 or more to the Patrons of the Institute, each new Patron receives a plaque and then a year bar for each additional year contributions are made. Contributions may he directed to RMCMI Patrons, 8057 S. Yukon Way, Littleton, CO 80128-5510. [ ] ARIZONA WINNER Steven W. Shipley University of Arizona The son of Bonnie Fawcett and David Shipley, Steven graduated from Catalina Foothills High School, Tucson, Arizona where lie attained a 3.5 GPA. In his third year at the University of Arizona lie is pursuing, a degree in mining engineering. He is a member of SME, Northwest Mining Association, and a volunteer at San Xavier Mining Laboratory -Miner. He participated in Football, Track, Wrestling and the DECA club while in high school He is the recipient in both the WAAIME and the Phelps Dodge scholarships. Steven volunteers during the academic year at the U of A San Xavier Mining Laboratory. He worked the summer of 2001 at the Black Butte Coal Company in Point of Rock, Wyoming. [ ] COLORADO WINNER Brian Gerdes Colorado School of Mines Graduating as the Valedictorian of Horizon High School with a 4.0 GPA, Brian is well prepared for the rigors of academia. In high school he was recognized in rite President's Education Awards Program and as a Radio Shack Tandy Scholar. lie belongs to SME, is a member of Fellowship of Christian Athletes, and volunteers at a local elementary school tutoring children. He enjoys intramural Sports. His father is Bruce Gerdes of Broomfield, Colorado Brian is holding a 3.75 GPA while studying for a mining engineering degree. He would like to go into reclamation scaring that his dream would be to reclaim an old mine and restore it to a function, al role in society again.

Jan 1, 2001

By S-L. Jämsä-Jounela

Fault diagnosis systems have attracted growing interest in a number of engineering fields. The number of applications has increased and successful results have been widely reported. The fault diagnosis system presented in this paper is integrated, and it monitors the states of the process and performs fault detection and diagnosis on the process equipment. The monitoring of process states is carried out by means of Kohonen Self-Organising Maps that is a powerful tool in visualisation and analysis of high dimensional data in engineering applications. This paper presents the results of SOM analysis carried out on the Outokumpu flash smelting process. The subsystems analyzed in more detail are the condition of the concentrate burner, the condition of the gas line on the basis of the pressure distribution in the process and the cooling water circulation of the waste heat boiler, and the condition of the furnace and furnace equipment on the basis of the temperature distribution in the furnace and gas line. Keywords: Fault diagnosis, Process monitoring, Kohonen Self-Organising Maps, flash smelting

Jan 1, 2001

By R. J. McGregor, Deepak Malhotra

Engineers frequently encounter situations where decisions that are counterintuitive to the logically trained engineering mind are made because of other influences, whether they be financial, social, cultural, or environmental. Such influences can overrule the "logical" decision-making process. The aim of this book is to explore some of the nontechnical issues, which most engineers don't learn about in school, that can have a major impact in the mining industry. This chapter gives a brief overview of this volume and introduces the topics that will be addressed.

Jan 1, 2001

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Savas Gorgun

The principal disturbances created by blasting in open pit mines are vibrations, air blast and fly rock. All of them, under some circumstances, caused damage to structures nearby and apart from this can be the source of permanent conflict with the inhabitations who live close to the operation. Therefore, prediction of ground vibration components is of great importance for the minimisation of the environmental complaints. This paper presents the result of ground vibration measurements induced by bench blasting realised at Can Open Pit Coal Mine located close to the residential area of Can town. Within the scope of this study, in order to predict peak particle velocity and determine the slope of the attenuation curve for this site, ground vibration components were measured for blast events during bench blast optimisation studies over a long period. During the study, while the parameters of scaled distance were recorded carefully, the ground vibration components were measured by means of two different types vibration monitors (White Mini-Seis and Instantel Minimate Plus Model) for 54 blast events. At the end of evaluation an empirical relationship with reasonable correlation was established between peak particle velocity and scaled distance for this site.

Jan 1, 2001