Search Documents

Boring of a 7.5Km long tunnel under the city of Stockholm commenced in January, 1987. The 3.5m diameter tunnel will pass under the buildings and as no ground settlement is allowed, the regulation for water leakage into the tunnel is very strict. Probe drilling will be carried out continuously ahead of the boring and when water is encountered the rock has to be grouted before passing with the TBM. The tunnelling system enables probe drilling to be carried out during boring with the TBM. This has earlier been a capacity reducing factor as the whole operation has been stopped during probe drilling. The project is using a new generation TBM especially developed for hard rock formations which require higher thrust per cutter to get a high penetration rate.

Jan 1, 1987

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability o mine safety management personnel to apply analytical techniques to Injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objectives and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. In this volume, the application of the quantitative procedures to mine-specific accident/injury experience data is discussed in detail in the form of case studies. The accident data from three mines are analyzed, and recommendations for training are proposed for each of the mines on the basis of this analysis. The procedures to apply cost-benefit analyses are described along with the cost benefit ratios for the training program/policies for the mines.

Jan 1, 1993

By Thomas P. Mucho

To document the performance of mine roof and roof support systems the U.S. Bureau of Mines (IJSBM) has been installing instrumentation at selected sites in U.S. coal mines. Much of this support and roof instrumentation has been installed in high stress conditions to maximize differences in performance. Summarized in this paper are the results of four such site investigations. The roof geology at the four sites is quite different and is quantified using the USBM's Coal Mine &f Rating (CMRR). The studies included detailed measurements of roof movement using multi-point extensometers, as well as measurements and monitoring of bolt loading. The investigations include developmental loading and abutment loading from longwall and room-and-pillar mining operations. Some of the issues examined are the effect of the horizontal stress field, the effect of installed tension (torque-tension versus resin bolts), the effect of reduced annulus bolt holes, and the differences between similar bolts supplied by different manufacturers.

Jan 1, 1995

By Richard Lee

SINCE the economics in the blast furnace resulting from enriching iron ores are so great, much attention, has been paid during the past few years to the various methods of concentrating lean ores, and, as the concentrated ore is usually of extreme fineness, various methods . of agglomeration and sintering, of more or less value, have been put 'into operation. The resulting agglomerated concentrates are generally obtained in the form of briquettes or nodules. The briquettes naturally divide themselves into two classes: (1) those made by the mixture of some binding agent, and then formed into briquettes under great pressure; and (2) those made by sintering the concentrates, the latter either being formed into bricks before exposure to heat or the sintered mass broken into fragments afterward. Of the first class I will not speak, as they are not used on an extensive scale in this country. The second class of briquettes, or those made by sintering, are simply masses of melted or fused silicate and oxide of iron mingled with more or less silicates of aluminum, lime, and magnesia. The fact that the material in a briquette is sintered is proof positive that there are no pores in the material. There are, however, quite a number of holes of greater or less diameter through the substance of the briquette. They are not pores in the common acceptance of that term as applied to ores by furnacemen, as the sides of the holes and channels are fused. In reality the material is simply mill cinder. It is practically untouched by the gases in the upper part of the furnace, and the iron has to be reduced by solid carbon in the boshes and hearth. Briquettes sometimes show a little saving in fuel in the furnace over an ore mixture of large lumps, but that saving is made simply because, owing to the numerous holes and channels through the mass, the briquette is practically composed of numerous small or fine lumps, and, as is well known, the finer the

Jan 10, 1913

By W. Hurst, R. E. Leeser, W. C. Goodson

Three aspects of gas deliverability are presented in this paper. The first treats with the gas deliverability or availability of a normal depletion-type dry gas field. Such encompasses not only the period of stabilized constant rate, but more so, the "tailings" when a fixed abandonment pressure is reached and the rate by necessity must decline. A comprehensive work plot is offered, developed from mathematics herein included, that removes the triai-and-errnr computations that attended such undertakings in the past. The second part treats with the discount factor of the open flow potential constant from what is observed initially in testing a gas well to what is evidenced when stabilization is reached. This prevails in tight formations, such as the Kansas Hugoton field which is offered as the example. The means of establishing this factor are pressure build-up curves which, as sustained by analytical deductions, reproduce this entire period of transient flow under conditions of a constant rate influx. Finally, what is offered in this paper is the deliverability performance of an exceedingly rich gas condensate field producing from a tight formation. The example shown is the Knox Bromide field in Oklahoma, producing from the Bromide formations. The results are ominous, showing early reduction in permeability to gas pow, due to the retrograde condensate forming in the pore space, with the attending early logging-up of these wells. The analytics of lowered permeability are incorporated in the gas deliverability formula along with the PVT data that gives the increased condensate liquid saturation as the gas flows to the well bore. This paper would not be complete without a critique oflered at the end. With the many gas wells now in production and those that have completed their life, there has been no factual information collected by any source as to what constitutes that permeability range where a gas well would be unimpaired in its gas deliverability by the presence of rich condensate content, and the lowered range where such would be harmful. This question confronts all producers. INTRODUCTION Various aspects of gas deliverability are presented in this paper that includes depletion-type reservoirs, deteriora- tion factor of the gas deliverability constant, and the performance of a rich gas condensate reservoir producing from a tight sand. With respect to the presentation of gas deliverability and its tailings for depletion-type gas reservoirs, one notes that this is essentially the information offered by every gas transmission company and producer appearing before the Federal Power Commission for Letters of Conveyance in the dedication of reserves. In the ordinary procedure, as many engage upon this study, trial-and-error calculations are included, particularly as apply to the tailings. For many years one of the writers has employed mathematical analyses to perform this step and avoid the complexities so associated. In the preparation of this paper these analyses have been amplified to include any slope n for the open flow potential relationship for which the tailings can be determined from Fig. 1. With reference to the deterioration or discount factor of the open flow potential constant as such occurs in the gas deliverability formula, this for the most part has been an unexplored subject. Although the issue first appeared in the Kansas Hugoton field, where such was surmised but only recently resolved, this situation of a deterioration of the gas deliverability constant can occur wherever dry gas production from a tight sand is encountered. The first concerted attacks upon this problem were the presentations of Hurst' and Goodson' before the Kansas Corporation Commission to show that transient fluid flow and unsteady-state flow formulas prevailed. This was amplified later before the Federal Power Commission3 to show that this deterioration factor could be identified from pressure build-up curves. This has been reported by McMahon.4 Its importance to the industry merits the review of these essential features in completing the program on the aspects of gas deliverability. Finally, as illustrated here, for a low permeability formation such as the Knox Bromide field where the gas is rich, representing some 165 bbl of condensate per MMcf of effluent gas, the gas deliverability can be of limited extent in the life of the field, leaving substantial amounts of condensate and gas unrecovered. In cases such as this, gas cycling is mandatory. This is particularly revealed by the fluid mechanics introduced here, employing factual field as well as laboratory data, to show this-restriction upon gas deliverability. PRESSURE DEPLETION What will now be offered is the study of gas deliver-

By K Sanematsu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Ore deposits of rare earth elements (REE) in South-East Asia are classified into four types: carbonatite, allanite, ion-adsorption and placer. Occurrences of the carbonatite deposits are confined almost exclusively to the Red River Fault Zone of northern Vietnam. Since the carbonatites contain dominantly REE fluorocarbonates (eg bastnasite) and lesser amounts of monazite, they are rich in light REE but poor in heavy REE. The ion-adsorption type deposits and prospects were found in Myanmar, Vietnam and Thailand. The ion-adsorption ores generally show lower REE grades than those of the carbonatite type and placer deposits; however, they could be enriched in HREE, which are more precious and scarce commodities than LREE. The ores consist of weathered granites with a significant amount of ion-exchangeable REE, which are extracted by using a dilute electrolyte solution. The ion-exchangeable REE are likely to be sourced from REE fluorocarbonates, allanite and titanite because these minerals are relatively susceptible to weathering and release REE3+ ions into soil water. In contrast, monazite and xenotime are resistant to chemical weathering and could form placer ores. Placer monazite and xenotime have been processed as by-products of placer Sn, Zr or Ti in Malaysia, Thailand and Indonesia, although the current production is small.CITATION:Sanematsu, K, 2015. Rare earth element deposits and prospective areas in South-East Asia, in Proceedings PACRIM 2015 Congress, pp 671–678 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Combine the MSHA and OSHA versions of the HazCom Helper into one easy-to-use software tool.

Jan 6, 2007

By Christopher Mark

Pillar recovery continues to be one of the more hazardous activities in underground coal mining. Safety requires that the roof above the intersection remain stable until after the pillar has been extracted. Artificial supports (timbers and Mobile Roof Supports) arc essential to roof stability, but so is the final remnant stump or pushout. Traditional mining practices usually called for the complete extraction of the final stump, but the recent trend (both in the U.S. and internationally) seems to be towards mining plans that leave a remnant stump. For this study, a sample of roof control plans from the Mine Health and Safety Administration (MSHA) Coal Districts were analyzed to determine current pillar recovery practices. Both full- and partial- extraction plans were included. Special attention was paid to whether plans require that a final stump be left, and whether requirements regarding the dimensions of the remnant stump are included. Foreign experience with final stumps is also summarized. It seems that the risk of major pillar falls can often be reduced by leaving final stumps that are large enough to protect the intersection, but small enough that they do not inhibit the caving of the gob. Because final stumps are often irregular in shape, a new approach for estimating their strength is described. Analyses were conducted to assess the effect of seam height and depth of cover on the potential variation in the size of remnant stumps.

Jan 1, 2001

By Charles G. Wade

In the ensuing years nitroglycerin-based dynamites will continually be replaced by water-based explosives. Until recently, the choice of a high explosive water-based product was limited to some type of water gel. Now, there is another choice. New emulsions are available having several degrees of sensitivity over a wide range of diameters. This paper discusses the properties of these new emulsions, e.g., physical and thermochemical; the relationship between diameter and explosive properties; and the effects of aluminum on total energy. There is also discussion of some of the unique properties of emulsions, their advantages, and how they differ from water gels.

Jan 1, 1978

By D. R. Maneval

The vast coal resources of North Slope, Alaska, can be expected to attract substantial interest because the nearly flat-lying coal beds of the coastal plain are specially amenable to surface mining. Mining on a scale large enough to justify coal development in this area could have severe environmental effects. The mitigation would be uncertain because large-scale coal mining and reclamation operations have not been carried out in the arctic. The deficiency of the scientific data base is another factor that requires consideration if coal mining has to develop in accordance with the objectives of PL 95-87. The objective of this paper is to establish the inter-relationship between the problems due to permafrost and factors in reclamation of post-mining land in order to find ways to transform nature in a rational and purposeful manner and to suggest specific reclamation approaches that may be appropriate in this region.

Jan 1, 1987

By Ellis J. Brien, O&apos

This afternoon I would like to talk to you about coal, its defi- nition, its constituents, its associated minerals and present and future coal preparation techniques. This discussion will be an attempt at presenting sufficient coal preparation and associated fundamentals to enable you to understand "deep cleaning", a more advanced beneficiation process which will be commercially practiced in the near future.

Jan 1, 1976

By Alfred W. G. Wilson

MR. F. E. LATHE: In studying any subject whatever, one should at least occasionally stand back from the canvas, as it were, and take a broad view of the picture. It is such a view of the subject of industrial minerals that Dr. Wilson has given us today, and, in consideration of our efforts to utilize Canada's resources to the utmost in the present emergency, it seems most timely. I shall confine my remarks on the subject to the resources of the atmosphere and hydrosphere. We seldom stop to realize our dependence upon the atmosphere, not merely as a source of the oxygen we breathe but also of other indispensable elements. As recently as the beginning of the present century, grave concern was felt lest the rapidly increasing population of the world should ultimately starve for lack of the nitrogen required for crop growth. I recently noticed a reference to the Scientific American for March, 1890-just fifty years ago-in which an account is given of work on the fixation of nitrogen, which, said the article, "leads to the conclusion that while cyanides and ammonia may be thus produced experimentally, there are as yet insuperable difficulties in the way of adapting those methods to industrial purposes". Y et, in the early part of the present century, the development of the arc, cyanamide, and synthetic ammonia processes of nitrogen fixation was such as to remove, for all time to come the possibility of a shortage of nitrogen. Today, the atmosphere is by far our greatest source of nitrogen, and the capacity of the nitrogen fixation plants of the world is at least 4,000,000 tons annually-much more than can at present be utilized. Pure oxygen or oxygen-enriched air offers great possibilities in metallurgy and industrial chemistry, but, so far, little application has been made. In a paper presented to the Institute in 1926, 1 pointed out the theoretical savings which could be effected by the use of oxygen in burning carbon-when the gases pass off at 2,460°F., the fuel saving is no less than 50 percent. The use of oxygen on a commercial scale is intimately tied up with the question of refractories, but we should not forget that the possible changes in metallurgical practice by the use of oxygen are truly of revolutionary character.

Jan 1, 1940

By Van H. Manning

"Under the organic act establishing it, the Bureau of Mines is authorized to conduct investigations designed to improve health and safety conditions in the mineral industry and to promote efficient development and utilization of our mineral resources. The field of the Bureau's activity, therefore, begins with the commercial development of mineral deposits and ends with the production and utilization of the final marketable product.In order to serve more efficiently the various sections of the country, the Bureau has established, in addition to its main offices at Washington, D. C., eleven field experiment stations, three field offices and several mine rescue cars and mina rescue stations. These field branches are so distributed as to cover most of the mining districts of this country, including Alaska. The field service in general deals with specific experimental problems, cooperative work with non-governmental institutions, and mina rescue work, while the Washington office is the administrative head and is responsible for the distribution of general information, the chiefs of the technical and administrative divisions of the Bureau being stationed there.The Bureau is prohibited by law from doing work exclusively for the benefit of any private company or individual. Generally speaking, the Bureau does no assaying, ore testing, or similar service work for the benefit of private companies or individuals. In response to requests for work of this sort a list of assay and ore testing laboratories is supplied. In referring inquiries to com-mercial laboratories or consulting engineers, care is taken to mention several names so as to avoid designating any one establishment or engineer."

Apr 1, 1920

By J. D. Milburn, H. J. Hill

In quantitative interpretation of electrical logs the presence of clay minerals introduces an additional variable which further complicates an already complex problern. Although recognizing the difficulties introduced as a result of the heterogeneity of natural sediments and despite the present incomplete state of knowledge regarding electrochemical behavior of shales, dissemirzated clay minerals and concentrated electrolytes, it was felt that useful empirical correlations might be obtained from experimental investigation. Six typical sandstone formations, having a wide variety of petrophysical properties, were selected for the study. Approximately 45 samples from each formation were selected to satisfactorily represent the range of pore size distribution within the particular formation, As a matter of general interest, four limestone formations were also included in the investigation. Previously proposed equations relating to resistivity, SP and interrelationship of the two phenomena have, where possible, been tested with data obtained in this investigation. These equations do not satisfactorily describe experimental behavior of samples through all degrees of shaliness or throughout the range of brine solution resistivities normally encountered in logging practice. An empirical equation has been developed which quantitatively relates formation resistivity factor to satirrnting solution resistivity, porosity, and "effective clay content." This relation is indicated to be uniformly applicable to clean or shaly reservoir rocks. It is shown that both the SP and resistivity phenomena of shaly samples are related to the sample cation exchange capacity per unit pore volume. The independent chemical determination of this parameter is thus a means of determining the "effective clay content" of samples. Some implications regarding theory and electric log interpretation of shaly sands are discussed. INTRODUCTION The use of electrical resistivity logs as a means for estimating formation porosity is based upon the original work of Archie1. It was shown by empirical methods that the resistivity of a rock, when 100 per cent saturated with brine solution, could be related to rock porosity through the equation, F = Ro/ RW = f-m.......(1) where F, the formation resistivity factor, is defined as the ratio of the resistivity of the 100 per cent water saturated rock, Ro, to the saturating solution resistivity, Rw; f is the ratio of pore volume to bulk volume; and m is the slope of the average line when the data are plotted on log-log paper. This relation was established for relatively shale-free formations containing water having high salt concentrations, and under these conditions F may be considered constant for a given rock sample. Applications of Eq. 1 to interpretation of logs of shale-free formations has been quite successful when satisfactory formation water resistivity data could be obtained. The most readily available means of estimating formation water resistivity is the self-potential log. Conventional methods of SP log interpretation involve correct.

Jan 1, 1957

By T. Ko, K. N. Han, C. S. Park, N. S. Kim, C. Yoon, H. Yoon

Quantitative analysis of Platinum Group Metals from ore samples and industrial materials using Inductively Coupled Plasma-Mass Spectrometer (ICP-MS), Inductively Coupled Plasma-Atomic Emission Spectrometer (ICP-AES), Atomic Absorption Spectrometer(AAS), and X-ray Fluorescence (XRF) techniques was conducted and the performance of various techniques was compared. The effects of different matrices in the sample materials were compared and discussed for each analytical technique. The ICP-AES technique exhibited better accuracy than AAS but showed limitations in its application due to strong spectral interference in the presence of common matrix elements such as iron. The ICP-MS showed the lowest detection limit and less spectral interferences than the previous two techniques. The XRF technique was also applied to examine the total amount of PGM from industrial materials. Results from each analytical method on various sources were presented and discussed.

Jan 1, 2003

Over the last four years, a major collaboration between CSIRO-MIS, UCT and JKMRC has produced two significant advances in the modelling of comminution. The Universal Comminution Model (UCM) uses parametric SPH/DEM studies of comminution and separation devices to calibrate mathematical models which are suitable for industrial use. The Virtual Comminution Machine (VCM) uses the same computationally intensive techniques based on discrete element modelling (DEM) and smoothed particle hydrodynamics (SPH) to directly model any comminution device by combining a CAD file describing the machine design, sophisticated ore characterisation methods and advanced particle scale flow and breakage simulation. The UCM should be useful for process analysis and optimisation of existing equipment and circuits while the VCM should make a major contribution to the evaluation and development of new machines. Progress to date is encouraging with several processes now well described using DEM. This paper also reports on progress towards combining DEM for particles with a realistic slurry model based on SPH for different types of comminution devices. In due course, this combination should allow accurate modelling of particle transport in wet mills to be combined with DEM models.

Jan 1, 2014

By Florian Kongoli

Minor components and flux additions can modify the liquidus temperatures of multicomponent slags. In industrial practice, slags with various levels of minor components require various flux additions in order to achieve the lowest possible liquidus temperature The prediction and the optimization of these combinations can decrease the cost of the overall process. In this work the effect of several minor components and flux additions such as Al2O3, MgO, and CaO, on the liquidus temperatures of multicomponent iron-silicate slags has been analyzed in terms of a thermodynamic model Various simple isothermal and non-isothermal diagrams are presented. These diagrams can be used directly by the process operators to define the optimum conditions under which the fluxes can be used to achieve the desired slag liquidus temperatures.

Jan 1, 1999

The reduction of zinc from slags by a molten, carbon-saturated bath was examined in a laboratory study under conditions of continuous slag feeding. The results show that it is possible to reduce the bulk of the zinc from the slag before there is a net reduction of iron. However, the recovery of zinc was not as high as in batch tests performed in an earlier study. Lead in the slag was reduced simultaneously with the zinc to very low levels and was volatilised. Copper in the slag was reduced and dissolved in the alloy. An attempt was made to identify potentially commercial ways of treating zinc slags using an iron bath. The approaches that appear to have the greatest potential are reduction in a batch process using electrical heating and reduction in a continuous process with co- or countercurrent flow of the slag and alloy. In the latter the alloy would be prepared in a separate furnace before being contacted with the slag. The purpose of this would be to superheat and carburise the alloy so that no additional heat or reductant would have to be supplied in the slag-alloy reactor

Jul 1, 1991

By M. C. Irani

This Bureau of Mines survey of methane emissions indicates that total daily emissions have declined from 227 MM ft3 in 1971 to 214.7 MM ft3 in 1973. The highest average daily emissions in million cubic feet per day observed in U.S. bituminous coal mines were, in decreasing order, Monongalia County, W. Va., 40.7; Marion County, W. Va., 23.1; Buchanan County, Va., 22.1; Washington County, Pa. , 12.4; Greene County, Pa. , 11.7; McDowell County, W. Va. , 11.4; Cambria County, Pa., 9.8; Jefferson County, Ala., 9.5; Wyoming County, W. Va., 6.0; Marshall County, W. Va., 4.8; and Indiana County, Pa., 4.8.

Jan 1, 1974

By S Brochot

During the development of a mining project, samples are taken for metallurgical tests. The sample can be a composite sample made of material coming from a selection of various drilling products or a sample coming from a mining test. This sample can represent several tonnes of material which are analysed and split to be used in various tests.In the current case, a composite sample is dedicated to semi-autogenous grinding (SAG) pilot plant tests. The property of interest is then the size distribution of the material. The sample is mixed and a subsample is taken to measure the size distribution which is considered as the feed size distribution. Then the remaining material of the sample is divided in several subsamples for batch grinding tests at different operating conditions. The product of each grinding test is then analysed to measure its size distribution.The grinding performances are analysed at the light of the measured size distributions for feed and product. But what is the accuracy of the measurement of these size distributions? What is the variability of the feed knowing each feed is just a subsample of the initial sample?The Pierre Gy theory of sampling answers these questions.The current paper presents, through a real example, the calculation of the measurement error of the size distributions and the variability of the feed between the different tests. The uncertainties of the grinding performances are then calculated and their impact on the results interpretation is then analysed.CITATION:Brochot, S, 2012. Sampling for grinding pilot plant test - the effect of size distribution variability, in Proceedings Sampling 2012 , pp 127-134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012