Search Documents

By Rolf R. von Oppenfeld

Onsite hazardous waste processors often find obtaining a Treatment Storage and Disposal (TSD) permit one of their first major challenges. Some processors may spend the time and money required by the permitting process, only to find out later that a permit was not necessary. This paper will present and analyze four strategies that processors may use to avoid obtaining a TSD permit. Some facilities will be able to remove their waste streams from RCRA's oversight by ensuring the material is not "hazardous" waste. Parties that treat waste while it is in process may be able to avoid generating "waste" altogether. Certain treatment facilities have been specifically exempted by EPA. Finally, treatment of waste while it is in generator storage tanks may be allowed without a RCRA TSD permit. Hazardous waste point of generation, an important determination relating to these strategies, will also be discussed. Generators and processors will find this paper useful when evaluating their permit exemption potential

Jan 1, 1996

By James J. Komadina, Robert R. Beebe

"Heap leaching of gold ores has enjoyed wide acceptance in the arid and semi-arid regions of the western U.S., Australia and South America. There are areas, however, where cold weather or excessive precipitation can limit the usefulness of heap leaching. Even in Nevada difficulties can be encountered which call for special operating procedures.The paper discusses the general climatological limitations and some of the techniques used to extend heap leaching into colder conditions. A case history of the Cripple Creek and Victor Gold Mining Company operation in Colorado examines 'valley-fill"" technology as an ideal cold-climate solution, where topographical conditions permit.AcknowledgementsThe authors gratefully acknowledge the management of Independence Mining Company for their permission to present this paper. The contributions of Golder Associates; Pikes Peak Mining Company Environmental Affairs Department staff, and the Colorado Department of Mines and Geology were all invaluable in successfully concluding this project.BackgroundWhen heap leaching of oxidized gold ores was introduced in the rnid-1970s it was aimed at large tonnages of low-grade material which could not, in general, be developed via conventional milling. Normally, the reasons for this were economic rather than technical: capital and operating costs for milling were simply too high. At first, grade was almost the only criterion, but deposits too small to justify milling were also potential targets for heap leaching.Renewed interest in gold was centered in the western United States and Australia, where exploration for milling-grade deposits had never really died. When heap leaching came along, it was in these areas that the first developments took place. Coincidentally, these same areas were favorable for heap leaching: climates were temperate for most of the year and competing land uses were limited. Even so, in the western United States in particular, winter temperatures were low enough to complicate operations. Precipitation was less a problem, although heavy snowfalls could periodically interfere as well."

Jan 1, 1997

By Mark C. Bronson

The feasibility of several pyrochemical approaches-for separating non-radioactive constituents from ICPP HLW calcine were examined. The removal of aluminum as AICI3 from aluminia calcine was successfully demonstrated. The examination of pyrochemical processes to remove non-radioactive constituents, primarily aluminium, zirconium, calcium and fluorine, from zirconia calcine showed that fluorine removal was required in order to chlorinate the calcine. A molten calcium chloride wash, a calcium reduction, and. a sulfuric acid treatment were examined as possible zirconia calcine pretreatment options for fluorine removal. Fluorine removal from simulated ICPP zirconia calcine was demonstrated by both a CaCl2 wash method and a sulfuric acid treatment method. X-ray fluorescence analysis indicated that greater than 97% of the fluorine can be removed by either method. Fluorine removal by a calcium reduction using an alloying agent, zinc, or a calcium reduction using, a filtration separation were also demonstrated, but the efficiencies of fluorine removal were considerably less ranging from 50 to 90%. Regeneration of CaCl2 from the salt and oxide residues of the CaCl2 wash experiments was also demonstrated 'by an aqueous dissolution method. From the salt residue, 85% or more of the CaCl2 was recovered and contained little if any CaF2 or CaO. From the oxide residue close to 100% of the CaC12 was recovered. Because of the overall success of the CaCI2 wash, it was determined to be the preferred fluorine removal process. The sulfuric acid treatment to remove fluorine is effective, but the proposed overall flowsheet has not' been adequately demonstrated.

Jan 1, 1995

By R. W. Charles

The Los Alamos National Laboratory, under the sponsorship of the U.S. Department of Energy; is involved with laboratory and field experiments to assist in development of the Hot Dry Rock concept of geothermal energy. The field program consists of experiments in which hot rock of low permeability is hydraulically fractured between two wellbores. Water is circulated from one well to the other through the fractured hot rock. Our field experiments are designed to test reservoir engineering parameters such as heat-extraction rates, water-loss rates, flow characteristics including impedance and buoyancy, seismic activity, and fluid chemistry. Laboratory experiments were designed to provide information on the mineral-water reactivity encountered during the field program. Two experimental circulation systems tested the rates of dissolution and alteration during dynamic flow. SOlubil ity of rock in agitated systems was studied. Moreover, pure minerals, samples of the granodiorite from the actual reservoir, and Tijeras Canyon granite have been reacted with distilled water and various solutions of NaCl, NaOH, and Na.CO.. The results of these experimental systems are compared to the observations made in field experiments done within the hot dry rock reservoir at a depth of approxi-mately 3 km where the initial rock temperature was 150 to 200°C.

Jan 1, 1981

By J. T. I. Poijärvi

The smelter off-gas cleaning and the weak acid treatment at Outokumpu Harjavalta Metals Oy are presented and described in this paper. The smelter consists of the copper and nickel smelters and the acid plant of three separate acid plants two of which are double contact and one single plant and of one liquid sulphur dioxide plant. The preliminary cooling and flue dust separation of the smelter off-gases from the copper and nickel flash smelting furnaces and converters in the waste heat boilers and in the hot electrostatic precipitators are described. The final cooling and cleaning of the gases in the scrubbers at the sulphuric acid plant and the treatment of the weak acid in the vacuum and in the submerged combustion evaporators for the removal of impurities are pre¬sented as well as the treatment of the condensates from the evaporators. The attention is paid to the generation of sulphur trioxide in the smelter off-gas and to the treatment of that in the weak acid bleed-off and to the utilization of the treated acid.

Jan 1, 1992

By Jose Hector Figueroa P.

Mexicana de Cananea, S.A de C.V. is a major copper producer mining a large deposit of the disseminated porphyry type considered one of the largest copper resources of the world with 2.7 billion tons of 0.60% copper for the mill plus 4.1 billion tons of averaging 0.26% copper for leaching. Mining of low grade sulfide leach ore, has been an important part of the overall production of the open pit mine which started in 1944. Before this time all the mining in Cananea was by underground methods. The leaching process in Cananea began on the 1920's with in situ operations in the underground mine and small dumps up to the 1950's. Large scale leaching operations began in 1960 and the copper solutions produced were treated in precipitation plants until 1,980 when the first SX/EW Plant was put in operation in Cananea. Leaching action is essentially ferric-bacterial, with no fiesh acid added to the leaching solutions. Traditionally, 5540% copper extraction is recovered fiom ROM, 70- 120 meter high leach dumps in 80 months of leaching. Cananea has successfully improved copper recoveries by implementing several actions that include: 1. Stripping of old dumps. 2. Leaching of old dumps through slotted casing. 3. Crushing conveying leach ore to minus 8 inch and stacking it in 30 meter lifts. As result of these actions, copper recovery has been increased' to about 70% of total copper with actions 1 and 2 and up to 85% in half the time by crushing-conveying the leach ore, based on the same solubility index of the run-of-mine ore. This paper describes the above actions that were implemented to enhance the leaching recoveries from. sulfide leach dumps and the economics of such actions.

Jan 1, 1999

By Paul Pajunen, Michael Sheedy

"Acid separation using short bed ion exchange is a now well established technology in copper refinery tankhouses. Refinery bleed streams from liberator cells are treated by short bed systems to produce an acid-free byproduct stream that contains the bleed metals and valuable nickel salts. Removing the acid eliminates the need for a black acid evaporator and reduces the amount of sodium carbonate required in nickel selective precipitation processes. The recovered sulfuric acid can be recycled to the tankhouse. This same technology is routinely used to treat other acids such as hydrochloric, nitric, and hydrofluoric. In the case of hydrochloric acid, the process can selectively separate chloro-anionic complexes such as Zn, Pb, and Cu, which are then eluted with water. The acid recovery technology can also be closely coupled with ion exchange processes in order to minimize regenerant acid consumption. In many hydrometallurgical applications resin regeneration often requires an acid dosage multiple times the stoichiometric minimum. Coupling an acid recovery bed with the IX column allows recovery and recycle of the free acid in the spent regenerant, thus reducing the overall acid consumption to just slightly more than stoichiometric.Short Bed Ion ExchangeThe short bed ion exchange process has been extensively used in the metal finishing industries since the early 1970s [1,2]. Short bed systems have also been sold to primary metals producers for the separation of sulfuric acid from copper refinery bleed streams [3] and for the recovery of nickel and cobalt from plant effluent streams. This unique technology optimizes the ion exchange process and offers a number of significant advantages over conventional ion exchange. The principal features and benefits of this technology are presented below."

Jan 1, 2012

By C. Camurri

Results from the Metallurgical Department of Universidad de Conception showed that fire-refined copper could be rolled without previous remelting for deoxidation. The goal of this work is to determine the rheology of fire-refined copper from tensile tests at different temperatures and strain rates, and Ford plane compression tests. All that in order to simulate and calculate rolling process variables. For rheology hardness coefficients, n variables between 0.28 at 600°C and 0.46 at ambient temperature are obtained. The sensibility coefficient for strain rate m varies between 0.056 at 600°C and 0.006 at ambient temperature. The activation energy for plastic flow Q in the considered temperature range is 1436 cal/mol.

Jan 1, 1999

The cleaning of copper containing fayalite slag using a CuFe alloy was studied under an oxygen pressure ranging from 10-7 to 5 X 10-11 atm at 1200º c. The reduction of copper from fayalite slags by Cu-Fe alloys was found to be very effective. For example, at a P 02 of 10-7 atm, the copper content in the slag was reduced from 4.1 to 0.402 wt. percent after 90 min. of reaction time using a Cu- 5.27 wt. percent Fe alloy. The copper reduction rates were found to be independent of P02 in the gas phase when using Cu-Fe alloys which exhibit an iron activity of greater than 0.4. A mechanism for slag c1eaning is proposed based on the concept that the Cu-Fe alloy lowers the oxygen potential of the slag according to Eq.1 1, fol1owed by the reduction of cuprous oxide by wustite as shown in Eq.2. Here X represents element X in the alloy phase while (X) represents the element in the slag phase. The copper and iron transfer behaviour obtained in this study are explained by a ?Stepwise equilibrium model.

Jan 1, 1985

By Irina V. Sokol

Alloyed steel chips and swarf formed during metal processing are looked upon as additional raw material In metallurgycal production. The manuscript presents some new methods for steel waste chips and swarf cleaning. One of them Is swarf and steel chips cleaning In ethylene tetrachloride with ultrasonic assistance and following, solvent regeneration. Thermal cleaning of waste chips and swarf provides exit gas products utilization. Catalyst Influence of metal surface on the process of thermal decomposition of liquid hydrocarbons during cleaning process has been studied. It has been our experience that the efficiency of metal waste cleaning technique depends on the storage time of the swarf. Waste chips and swarf cleaning procedures presented in the manuscript have been proved economically advantageous and environmentally appropriate.

Jan 1, 1995

By Yang Tian-zu

The separation of precious metals from base metals containing in gold-antimony alloys by selective chlorination leaching under controlling potential was studied in this work. The effects of the consumption of hydrogen peroxide, the concentration of hydrochloric acid, the concentration of sulfuric acid, leaching temperature, leaching time and the liquid-solid ratio in hydrochloric acid system on the leaching efficiencies of the base metals have been investigated. The optimal leaching conditions of the gold-antimony alloys are as follows: hydrochloric acid concentration 4.0mol?L-1, sulfuric acid concentration 1.2mol?L-1, liquid-solid ratio L:S=7.5:1, the leaching temperature 80 0C, leaching time 2h, and the oxidation potential of the leaching system 400±20mV( vs SCE).The leaching efficiencies of copper, nickel and antimony are more than 99% and the gold leaching efficiency is about 0.042% under the above leaching conditions. The base metals containing in the gold-antimony alloy are separated from the precious metals thoroughly.

Jan 1, 2006

By V. Bhagavathy

This paper describes a method for the determination of traces of rare earths using energy dispersive x-ray fluorescence spectrometry (EDXRF) after preconcentration of their oxine complexes onto activated carbon. Various parameters that influence adsorptive preconcentration of rare earths onto activated carbon viz. pH, amounts of activated carbon and oxine, time of stirring and aqueous phase volume were systematically studied. A numerical method based on simple least square procedure using fifth order polynomial with 25 consecutive values was developed for smoothing and differentiation of EDXRF data which was previously digitized and averaged. First order derivative EDXRF in conjunction with adsorptive preconcentration on activated carbon enables to determine as low as 10 ppb of each of individual rare earth elements.

Jan 1, 1989

By E. Açma

In this study, the production of Cu, Co, and magnetic iron oxide from the ancient copper, slags, located in Küre-Turkey, is investigated. In the process under development, fayalitic slags containing 1% Cu, 0.43% Co are reduced in a D.C. arc furnace with coke or graphite additions. A metallic alloy, consisting of 3.8% Cu, 3.3% Co, 2.1% S, and the rest being Ice, is produced by granulation of the liquid metal. About 85% recoveries of Cu and C:o are achieved by hot sulfuric acid leaching of these granules followed by H2S precipitation. The, production of magnetic iron oxide is possible from the discarded leach solution, loaded v:ith FeS04, by using a method with geothite precipitation, dehydration, controlled reduction, and re-oxidation steps. The magnetic oxides produced have 20 m2Jg surface area, 1:8.3 aspect ratio, and the coercivity of 330-380 Oersted.

Jan 1, 1993

By Purushottam Kumar

Keywords: Magnetostriction, magnetic properties, Pd(Fe,Co,Ni) single crystals Fe-Pd, Co-Pd and Ni-Pd alloy systems show appreciable magnetostrictive strains that are of interest for sensor applications. These systems exhibit congruent melting minima. In this work the magnetic and magnetostrictive behavior of congruent melting Fe-Pd, Co-Pd, and Ni-Pd compositions have been examined. The alloys examined include Fe-54.9 at.-% Pd, Ni-45.4 at.-% Pd, and Co-45 at.-% Pd. The paper describes the growth of bulk single crystals of these alloys using Czochralski technique. X-ray diffractometer was used to obtain rocking curves that were used to determine the [001] crystal direction. Magnetostriction in [001] direction was measured using strain gages. Magnetic properties were measured using a vibrating sample magnetometer. Ni-Pd showed the highest magnetostriction values among the congruent melting compositions. Magnetic and magnetostrictive behaviors of these alloy single crystals are presented.

Jan 1, 2005

By Manuel Zamalloa

The outstanding metallurgical performance of the Noranda continuous converter (NCv) in operation since November 1997 has allowed the company to meet production and environmental targets. This achievement positions this new technology as a strong alternative continuous converting technology for copper production. Knowledge of slag chemistry has been important in this respect. The purpose of this paper is to discuss the effect of key parameters including temperature, oxygen potential, slag composition and levels of copper oxide in slag on the conditions leading to magnetite precipitation, as well as on the conditions affecting the liquidus ranges of NCv slag. The above variables are evaluated using industrial data and thermodynamic predictions. Practical implications of customizing operational fluxing procedures to determine optimum operating windows are also discussed.

Jan 1, 1999

By Robert Fritzsch, Ragnhild E. Aune, Mark William Kennedy, Behzad Mirzaei

"The quantitative particle concentration can give important information about the cleanliness of melts for quality control in primary and secondary production of aluminum. Manual quantification of the particle concentration is normally a time consuming process and human control can bias the acquired images and particle count.The present paper explains the automated image-processing steps for the quantification of SiC-particles, with equivalent diameters from 2 to 25 µm, in solidified A356. A total of 700 micrographs, acquired with a standard white light microscope with 10 x magnification, were analyzed. The applied software (Image Pro-Plus 7.0 from MediaCybemetics®) allows for programming of macros which in tum provides the user with a higher degree of control. The automated results are compared with the results obtained by manually counting the particles in the same micrographs. The impact of the automated results on the estimated filtration efficiency was established to be only -3%.IntroductionInclusions are both indigenous and exogenous particulates that are present in commercial metals such as aluminum. If large individual or large numbers of inclusions are present, they can have a significant negative impact on the appearance, mechanical and chemical behavior of products produced from the metal. Aluminum is known to contain large numbers of inclusions: =50 µm in size, e.g. typically <l ppm by volume or <100,000 inclusions of>20 µm per kg of metal as detectable using a Liquid Metal Cleanliness Analyzer, LiMCA [1]. Depending on the final application of the aluminum, inclusions can render the metal 'not fit for purpose', and result in serious economic consequences to metal producers.It is not surprising that the aluminum industry has developed a number of treatment processes to improve metal cleanliness, given the large number of high value products whose quality can be adversely affected by inclusions. CFFs are the most commonly applied filtration process and have been used to filter >50% of the world production of aluminum since the 1990's [2].Inclusions in aluminum may be particles, bifilms [3] or clusters of: oxides (Al2O3 , SiO2), spinels (MgO· Al2O3), carbides (SiC, Al4C3), nitrides (AlN), borides (TiB2), sulfides, phosphides and intermetallics [ 4]."

Jan 1, 2013

By Dale W. Collins

The disposal of arsenic from copper operations possess various health, environmental and processing problems. There are basically two areas of concern. The first being the disposal or treatment of smelter flue dusts and the second the removal of arsenic from refinery electrolytes. A number of treatment options have been proposed including the addition of soluble arsenic wastes to copper heap and dump leaching solutions. This approach will allow arsenic to be reintroduced to the ore via Solvent Extraction (SX) raffinate associated with hydrometallurgical operations. Knowledge of the attenuation behavior and mechanism during leaching is important in determining the long term stability of arsenic and the success of this approach. Parameters, such as uptake capacity, pH, particle size and solution chemistry have been investigated. Arsenic attenuation has been examined using column leaching with experiments employing both continuous flow and pulsed additions of As(V). In the initial stages of leaching, the attenuation of arsenic appears to depend on the pH and iron concentration in the effluent. Arsenic stability in the copper oxide ore has been examined with rinses of progressively lower pH.

Jan 1, 1994

By R. P. Tavares, M. Isac, R. I. L. Guthrie

"The configuration of the metal delivery system used in twin-roll casting can play a significant role in determining both internal and surface quality of the strips produced by this process.In the present work, a mathematical model for coupled turbulent fluid flow, heat transfer and solidification was developed and used in the study of metal delivery systems for twin-roll casting of low-carbon steels. This study was applied to a pilot twin-roll caster being investigated in Canada, with a roll radius of 0.3 m, producing strips of thicknesses from 4 to 7 mm, at roll speeds ranging between 4 and 12 m/min. Various configurations of metal delivery systems were simulated and their effects on the advance of the interdendritic solidification front and levels of turbulence and temperature within the caster investigated. According to the predictions of the model, an extended nozzle with inlet flow towards the surface of the rolls seems to be the best alternative for feeding liquid steel into twin-roll casters.A full scale water model of a pilot twin-roll caster was also built and used to qualitatively validate the predictions of the mathematical model.Various techniques for fluid flowvisualization were applied. In general, the predictions of the mathematical model were in reasonable agreement with the experiments with the water model."

Jan 1, 1999

By A. Lackner

Using the CFD software package FIRE, the smelting process inside a cyclone reactor is modelled. The fluid flow is calculated 3 dim., using different turbulence models. The effects of design parameters (length and diameter of the cyclone, concentrate feeding tangentially or from the top,..) and operating conditions are investigated. Single particle traces illustrate how to increase particle retention time before the particles reach the liquid film flowing down the cyclone wall. Moreover a two phase flow approach is developed, based on the "Discrete Droplet Model". The position, velocity, diameter and temperature of each reacting particle is described. The results show the advantages of top concentrate feeding, large height/width ratio of the tuyeres and increasing number of tangentially gas inlets.

Jan 1, 1995

By Vianey Garcia-Osorio

One of the problems in the carbothermic aluminum process is the substantial loss of aluminum compounds as vapors due to the high temperatures in the process. In order to solve this problem a Vapor Recovery Unit (VRU) is proposed. In this unit operation the aluminum vapor undergoes a series of heterogeneous non-catalytic reactions forming solid, liquid and gas products. In this work a model for the simulation of this unit was developed which includes heat and material balances as well as heterogeneous non-catalytic reactions. The model leads to a system of differential equations; its solution was implemented in Matlab giving as a result a stage-by- stage solid-fluid reaction model.

Jan 1, 2001