Search Documents

By O. Tranbarger

In aging tunnels, wall and roof deterioration can eventually result in defects that must be detected and repaired to maintain safe structural conditions. In investigating tunnel defect conditions, a specialized FM radar system was developed with a programmable VHF and UHF operating sweep range for optimizing the penetration and measurement capabilities. The new FM radar technology was tested in two aging brick-lined tunnels in New York City. Test results showed that FM radar signals could penetrate eight courses of water-saturated brick and that the original steel liner outside the tunnel walls was intact.

Jan 1, 1985

General. Data for the operating information given in the 15 tables in this chapter was obtained from voluminous questionnaires sent to over 100 operating companies in 1972. There has been a considera¬ble change since then in supply and power costs and many companies have had expansions or revisions since that time, so it must be realized that information is valid for the year 1972. This is true except for the three new properties of Sacaton, Metcalf, and Pinto Valley. These three operations started up since 1972 and all information for them was obtained in 1975. The questionnaires were sent to all major copper properties throughout the world as well as to many smaller units and to some mines that had complex or unusual conditions. Properties for which no information is given did not submit completed questionnaires. Several operations were unable to supply information requested be¬cause of company policy prohibiting it. However, data is presented for 75 different operating properties. The reference number of the left-hand column is the same for all 15 tables of data. If the company had several operating properties as of 1972, then subsequent properties use the same number but a different letter. For example, Anaconda's property at Butte, Mont., is IA, whereas Anaconda's (now Anamax) Twin Buttes property in Arizona is IB. Table I gives general data for the properties including exact loca¬tion, milling rate, pertinent assay values and recoveries, and a brief listing of ore and gangue minerals. It was not possible to obtain any more information from the properties in Chile except that given in Table I. Crushing. Crushing plant operating data is given in Table 2. This table gives data on the crushers, feeders, and screens used at each property. The data obtained on feeders was confusing, but, rather than completely eliminate this information, it was decided to report it as given. The confusion lies only in the description of where the feeder is located. Where a primary feeder is listed it was not possible to determine if this feeder was on primary feed or primary discharge. For secondary feeders it is known that the feeder listed usually is feeding the secondary crushers, but at some properties it is handling the secondary crusher discharge. The same reasoning holds true for tertiary feeders-they handle either tertiary feed or discharge. This table contains a voluminous amount of data. A column giving tons per day per square foot of screen area would have been very informative, but some properties included circulating load in the feed rate and others listed new feed only, so calculations were meaningless. Autogenous Mills. The use of autogenous or semiautogenous mills for any property must be given serious consideration in the future. Table 3 lists data for four properties that are fully autogenous and four more semiautogenous mills that use balls to supplement the chunks of ore. This method of grinding is especially applicable when the ore is of such a nature that crushing problems would be severe, such as when ore is wet or sticky or contains a lot of fines. Paradoxically, it should also be considered when ore is tough and hard and blocky because then the competency of the ore means it can serve well as the grinding media. Where the ore varies greatly in hardness, as at Cyprus Pima and Lornex, semiautogenous grinding has been especially beneficial with capital costs and operating costs both 10-20% lower than could be obtained with conventional crushing and grinding. Rod Mills. For a great many years the standard milling operation used two- or three-stage crushing followed by open circuit rod mills and then ball mills in closed circuit with classifiers of some kind. A surprising number of properties crush to the fine size of about 3/8 in. and then use ball mills only, in closed circuit, with no rod mills. It is difficult to say whether rod mill-ball mill circuits or ball mill only is the best. One can be certain of two things: (1) the argument will go on for a long time and (2) for some mills one method obviously was superior over the other. As ball mills of 14, 15 ft, and larger came into use, more properties like Duval Sierrita (16b ft diam by 19 ft long) and Bougainville (18 x 21 ft) were built with single-stage ball mill grinding. Although there are larger rod mills used, especially in the iron ore industry, the largest rod mills on copper ore are at Twin Buttes (14 x 18.5 ft) and at Gibraltar (13'A x 20 ft). Table 4 lists operating data for rod mills. If a company is listed in Table I

Jan 1, 1985

By G. Swartz, R. J. Brison, R. A. Wyman, J. P. Vandenhoeck, S. E. Khalafalla

Magnetic fluids are commonly composed of ultrafine submicron particles of magnetite (Fe3O4) dispersed in either a kerosene or a water carrier medium with oleic acid as a protective colloid. The unique property of these fluids is that when the magnetic particles are attracted to a magnet the carrier medium moves along with the particles so that the liquid also appears magnetic. The availability of a fluid whose gross behavior changes sharply in a magnetic field without affecting its rheologic characteristics is becoming critical for many technologic applications. About two gener¬ations ago suspensions of relatively large, micron-sized ferromagnetic particles in oil proved useful in clutches, brakes, and dashpots. These were called magnetic clutch materials, and their viscosities were highly dependent upon the applied magnetic field, in contrast to true mag¬netic fluids which retain their fluidic characteristics under all applied fields and field gradients. While the term "ferrofluid" was used by Rosensweig and Kaiser&apos; to designate a magnetic colloid composed of a dispersed magnetic ferrous material, the more general term, "mag¬netic fluid," is preferred. This is because these fluids may contain ferro- or ferrimagnetic substances, such as cobalt, nickel, gadolinium, dysprosium, or magnetic ferrites in carrier liquids, such as hydrocar¬bons (kerosene), silicones, water, fluorocarbons, etc. Preparation of Magnetic Fluids Magnetic fluids were first prepared by Papell and Faber, at the NASA Lewis Research Center, Cleveland, Ohio, by tumbling ferrite materials for several weeks in a carrier medium (such as kerosene) and a dispersing agent (such as oleic acid) with steel balls. Rosensweig et al.1 compared the stability of their ferrofluids obtained from both metallic iron and the magnetic oxides of iron, Fe3O4 and yFe2O3. They found that, although the saturation magnetization of iron is 3.5 times greater than that of magnetite, its colloidal solutions deterio¬rated much more rapidly. The iron particles were undoubtedly rapidly oxidized to a nonmagnetic state due to the enormous surface area of these colloidal particles. Because the properties of these fluids are highly dependent on particle size and may acquire opposite characteristics by small incre¬ments in that size, more controllable methods of preparation have been developed recently by Khalafalla and Reimers.6 In one method metastabilized pyrophoric wiistite is ground to colloidal size in a kerosene oleic acid mixture, and then it is disproportionated to colloi¬dal magnetite and iron at temperatures just below the eutectoidal temperature of wüstite stability (570°C); thus, t < 570°C 4 FeO t > 570°C Fe + Fe30, (1) Because of its antiferromagnetic characteristics, the precursor wüstite is much easier to grind than magnetite. Another method3 avoids grinding entirely and utilizes a peptiza¬tion technique from ferrous materials in the molecular state of aggrega¬tion. This latter procedure has resulted in preparation of strong fluids at considerable savings in cost.

Jan 1, 1985

By R. L. White

Classification of Mills Mills may be classified under four categories that relate to the type of action utilized to grind the material: Tumbling. The most important of these to the minerals processing industry are tumbling mills. Grinding media is actuated in a free¬form pattern in a rotating drum causing it to tumble, material being ground passing through the tumbling media. Work is done by a combi¬nation of attrition and impact. Impact. Grinding media is actuated in a distinctive pattern so that it impacts the material being ground. Work is done by impact. Roller. Grinding media is actuated in a distinctive pattern, mate¬rial being ground passing under or between the media. Work is done by compression. Fluid Energy. There is no grinding media as such. Energy is imparted to the material by transfer of kinetic energy from the fluid to the material. Grinding is accomplished by interparticle impact and attrition. Tumbling Mitts The main physical arrangement consists of a lined cylindrical drum mounted on trunnion bearings driven by a ring gear and pinion, in turn connected directly or through a reducer to the electric motor. Variations to this general arrangement include: (1) Drum mounted on rollers instead of trunnions. (2) Bearings on the drum directly, not on trunnions. (3) Utilization of multiple pinions on the gear. (4) Trunnion-type drive arrangement through a gear reducer with¬out the use of a ring gear. (5) Motor rotor mounted directly on the drum with stator around the drum, thus eliminating the gearing. The drum consists of a shell and heads lined with replaceable liners of various types and configurations. Various types of tumbling mills are tabulated; illustrations of some are shown. The types are so designed for specific purposes. Media utilized include steel rods, balls, or rock of the same material as being ground or of special material in the instance where iron contami¬nation is detrimental (see Figs. 9 and 10 and Table 2). Impact Mills Although there may be some overlapping of interpretation of terms, impact mills are considered those in which the media is actuated in a distinctive manner, at relatively high speed, impacting the material to be ground. There is an overlapping also in what may be considered to be crushing equipment rather than grinding equipment. Hammer Mill or Impactor. Material is fed into the equipment; inside hammers of impactors revolve at a high speed, breaking the material on impact with the hammers (see Fig. 11). Material is also thrown against the periphery of the mill, causing impact grinding to occur. Equipment is normally lined with replaceable abrasive resis¬tant metal; hammers are also

Jan 1, 1985

By M. C. Rockwell

There are approximately 1,800,000 t of discarded dolomitic-limestone tailings from the Gays River lead/zinc mining operation in Nova Scotia. Neutralization effectiveness similar to an agricultural grade limestone and low contents of residual metals make the tailings a suitable source&apos; of soil conditioner material for the local market. However, the fine particle size, 98% passing 147µm, and a high moisture content make their handling and application difficult. Agglomeration of the tailings into relatively small hard pellets was investigated and difficul¬ties were overcome. Pellets with a range of pH values and various amounts of soil nutrients and moisture content less than 10% were obtained, from tailings containing 20% initial moisture, through the addition of less than 15% selected materials.

Jan 1, 1985

Contents

Jan 1, 1985

By J. T. Kline

This paper will present a review of the underground leaching of remnant copper mineralization left as a result of the block cave mining operation at the Lakeshore Mine in Casa Grande, Arizona.

Jan 1, 1985

By E. F. Klein, R. L. Eacret

Introduction In contrast to the general type of crushing mechanism in which the crushing surfaces alternately approach and withdraw from each other, described earlier in this section, and continuous-pressure break¬ers such as rolls and roller mills that will be described in a later chapter, impact crushers load by striking pieces of rock while in free fall and hurling them at high speed against stationary surfaces. Because the impact crusher depends for its effectiveness upon high velocity, wear is greater than in the slower-moving jaw and cone¬type wear parts, and for this reason its use is strictly limited to rela¬tively soft, friable, and sticky rocks that are characteristic of many nonmetallic mineral deposits. A few of these are phosphates, lime¬stone, barite, clay, asbestos rock, and coal. However, several examples of their use on soft lead-zinc and precious metal ores have been known. Although the use of impact crushers is expanding today into the range of ores containing as much as 15-18% silica, Taggart16 set the practical limit at 5%, and in the 1940s and 1950s several installa¬tions in the US and western Europe exceeded the limits of economical maintenance and were quickly superseded by the slower-moving, con¬ventional crushers. A rock that tends to be plastic or bouncy in a jaw or gyratory crusher when the force is applied slowly to reach ultimate strength, may become brittle with rapid loading and thus increase the effective¬ness of the applied forces. For this reason it is to be expected that as the quality of hammers, grates, plates, and cages improves with advances in steel technology, the use of high-speed crushers of this kind will increase. Terminology Modern usage differentiates between the impactor and the hammer mill, the former relying primarily on the impact of hammers (fixed or free-swinging) and secondarily upon pieces striking one another or steel surfaces; the hammer mill relies on both the centrifugal impact force of free-swinging hammers and the attrition and shear action between these hammers and well-placed grates suspended at the bot¬tom just below the hammer circle. The hammer mill, because of its grate discharge, restricts discharge of oversize rock to the grate open¬ing, while at the same time providing a trap for removal of tramp iron or other uncrushables. The impactor discharges free, so generally works with a screen to control product sizes. The question of terminology, impactor vs, hammer mill, creates difficulties because the similarities appear to outweigh the differences by far; if one were to list the similarities in order of importance and then the differences, he would be forced to conclude that they would best be dealt with as a single kind of crusher. Taggart16 gave it four names and added "as it is variously known," but it must be remembered that in 1945 the machine was nearly exclusively of the flailing-hammer type, while today the fixed-hammer rotor is also com¬mon. In this chapter the terms impactor and hammer mill will be used where they seem to apply. It is perhaps unfortunate that this terminology is being confused with rock breaking at the mine, usually with hand-held tools, e.g., the article "High-Energy Impact Rockbreaking" by Grantmyre and Hawkes, CIM Bulletin, August 1975. General Description Impact breakers, impact crushers, and hammer mills accomplish material breaking and reduction primarily through impact action of the material with fixed or free-swinging hammers revolving about a central rotor. The material to be crushed enters through an opening at the top or top side known as the "feed opening" or "hopper opening" and falls into the path of rotation (hammer circle) of the hammers. Initial breakage is accomplished in midair by collision of the dropping feed material with high-speed hammers. The second stage of breakage occurs when the pieces hit plates or breaker bars which line the crusher boxlike frame. Hammer mills rely further on a shearing and attrition action between free-swinging hammers and grid bars or grates at the crusher bottom which restrict discharge of oversize material until it is broken sufficiently to pass through the grid opening. The term hammer is used in reference to the piece which strikes the material, whether it is fixed on the rotor or free-swinging. It

Jan 1, 1985

By M. D. Flavel, J. C. Motz, G. V. Jergensen

Introduction Compared to the gyratory crusher, the cone crusher is character¬ized by its higher speed and a flat crushing chamber design which is intended to give a high capacity and reduction ratio for materials suitable to this type of processing. The aim is to retain material longer in the crushing chamber to do more work on material as it is being processed. A concept of how a piece of stone might flow through a secondary crushing chamber is shown in Fig. 45. The number of times material will be nipped during crushing will depend on material size, friability, and the geometry of the crushing chamber as well as its speed and eccentric throw. Cone crushers are usually specified in terms of closed-side setting (CSS) and a given quantity of material passing a particular square-mesh screen size. A criterion of product passing closed-side setting is often available. This value will vary according to the particular crusher design and the details of its applica¬tion. Essentially, cone crushers can be classified into distinct types, depending on their duty. Crusher sizes for all duties are described by terms arising out of common industry usage, such as 3-ft, 7-ft, etc., which refer to the crushing-head (mantle) diameter. At present the range of sizes available varies from approximately 2 to 10 ft diam. Weights vary in the range of 5 to 200 tons, and connected horsepowers range from 10 through 700. There are so many variations that specifics should be obtained from machine manufacturers. The crushing chambers that are fitted to various machines are also often referred to by terms arising out of common usage, such as standard for secondary crushers, and short head for tertiary crush¬ers, which refer specifically to the Symons design. Also used are more specific but equally vague descriptions, such as coarse, intermedi¬ate, and fine chambers. Some manufacturers such as Allis-Chalmers with their Hydrocone crushers refer to the model number of the machine by the feed opening and the diameter of the mantle. For example, a Model 10-84 Hydrocone crusher has an 84-in. diam man¬tle, and is capable of accepting a 10-in. diam sphere at the feed point to the crushing chamber. Rexnord and Telsmith define crushing cavi¬ties in their capacity tables as feed openings at minimum recommended discharge settings (closed-side settings). Each practice offers guidelines which should be carefully defined for the specific crushing problem. The utilization of a cone crusher depends on how well it is controlled and the features of the circuit in which it operates. Normally, it will operate in the range of 75 to 85% of the peak capacity. It is likely that industry pressures will call for a standarized de¬ applied crushing power. Experience has shown that the crushing process is more controllable if certain reduction ratios are adhered to for each stage. Technically, this is defined as that size of feed (in. or mm) of which 80% will pass, divided by the size of the product (in. or mm) which 80% will pass. Secondary Crushers These are the cone crushers which accept suitable feed size material either prepared by a primary crusher or occurring naturally, and reduce it to a size suitable for marketing in one stage, or make feed for subsequent crushing or grinding stages. Secondary crushers have feed openings of 4 to 25 in. in the larger (7-ft) models down to a 2&apos;/a to 4 in. in the smallest 24-in. models. Reduction ratios normally range between 3:1 and seldom more than 5:1. In the 7-ft models, the cone crusher typically makes a product all passing 2 in., but this is dependent on the machine design and properties of the material being treated. Secondary crushers most commonly operate in open circuit. They also are operated in closed circuit with a vibrating screen, depending upon product requirements and conditions where the reduction ratio does not cause excessive power draw and build-up of circulating load. Screening ahead of secondary crushers is generally recommended, especially where the feed contains more than 25% material smaller than the desired closed-side setting. Tertiary Crushers These are cone crushers that normally take secondary crusher product and reduce it to a marketable product or make it suitable for subsequent comminution steps. The reduction achieved is a func¬tion of the crusher design and the properties of the material to be treated. The reduction ratio is normally in the range between 1.5 and 2 to 1, and seldom more than 3 to 1. The tertiary crusher normally operates in closed circuit with a vibrating screen and makes a product smaller than all passing &apos;h or 5/8 in. Fine Crushers Sometimes these machines are called sand crushers and are called by various manufacturer brand names, such as Gyradisc, Hydrofine, V.F.C., and others. A cross section of a Symons Gyradisc crusher is shown in Fig. 46. Essentially, these crushers would be used in a fourth-stage crushing operation, but could be called on to reduce a screened feed size fraction from a secondary or primary crushing operation. This type of crusher normally receives feed no coarser than 1&apos;h in. that is scalped of all over-sized material and operates in closed circuit with a vibrating screen. For average materials, typical product is &apos;/e in. top size, although a -10 mesh product can be produced on those materials having suitable characteristics. The crusher is nor¬mally operated in a separate circuit from the main crushing plant because of the variations in output rates that are caused by varying physical properties in the feed. The reduction ratio is generally less than 2:1, and circulating loads are generally high. More interparticle crushing takes place in these machines than with conventional cone crushers and capacities can be more sensitive to changes in moisture content, feed size graduation, and other physical properties. Design Features For the various applications, crusher manufacturers normally have a range of crushers of different sizes and power ratings to select from.

Jan 1, 1985

By Robert E. Moore

Investigators have attempted to develop lime refractories on a scale for broad applications in the metal and ceramic industries for several decades. There was a flurry of activity in the early to mid-fifties but no commercial developments were forthcoming. The literature of that period yields little information on plant trials. A major factor suppressing past interest in lime has to have been the high success with the application of magnesic and dolomitic materials. These materials, usually tar-bonded or impregnated, have become the refractories success story of the past two decades, especially in BOF applications. It is safe to say that their development and application has essentially plateaued, and that work today is focussed on finding cheaper paths to produce MgO-based refractories. For example there are efforts underway to extract MgO from mineral magnesite and to combine natural dolomite with MgO1. Beginning in the late sixties, rather intensive research began on the development of CaO brick, especially in East and West Germany, in Poland, and other communist bloc satellites, &apos;and also in Italy and Spain. One speculates that the motivation was a regional shortage of good magnesia and dolomitic material. Of course, There has always existed the prospect of cost savings should it be possible to use raw limestone as the starting material. Quite a large literature has appeared treating of these developments which in the early seventies had already reached full plant scale trials and uses. Some of the directions followed in the research have led to novel methods of brick manufacture.

Jan 1, 1985

By D. J. DeLeo

In recent years the hue and cry of American industry concerning the pressure of foreign competition on the domestic marketplace has become all too familiar to most of us, as we are all well aware, the steel industry has not been exempted from this pressure, reduced production levels, work force cutbacks, and in some extreme cases, plant closings and company liquidations have resulted, new regulations governing imports and quotas have been enacted, foreign trade agreements reached, and more strict regulation enforcement practices undertaken, despite these, and other measures, the impact of aggressive foreign competition has not lessened, the concensus of numerous management consultants is that in order to successfully cope with these problems we must draw on all available technology to provide the tools which will enable us to enhance our management effectiveness, one area requiring particularly close attention in any mining operation is that of managing critical resources - namely time, energy and equipment in a fast and efficient manner, In mining, with critical resources deployed over a large geographical area, any degree of success involved with resource management is dependent upon knowing the current status of all work related activities, if we, as mine operators, are to be more successful in this area, additional tools are a necessity and modern technology has provided a multitude of new options from which to choose.

Jan 1, 1985

By Scott G. Britton

Planning is a management tool used to solve problems and provide data and decision alternatives for company growth, profitability, and direction. Strategic planning is defined as the efforts needed to accurately measure the risks of obtaining a result from future actions given a finite number of outcomes. The techniques of strategic planning are being applied more and more to underground mine design as a result of the fierce market conditions underwhich the industry is facing today, and the conditions they will likely face in the future. The objectives of strategic planning are centered on the ability of the operator or company to manuever its limited resources to the best position available under the given future scenarios. This paper briefly examines the most popular techniques for accomplishing these objectives, how these techniques fit into the current mine management decision-making, and what results to expect from these techniques in planning efficient underground mines.

Jan 1, 1985

By I. H. Warren, F. A. Forward, D. E. Pickett, Ernest Peters, Alvin H. Ross, I. M. Masters, N. P. Finkelstein, R. Derry, A. W. Fletcher

In this section the chemical, physical, and mechanical principles of hydrometallurgical processes are developed and reviewed. Plant practice is not discussed other than to note the metals which are processed using the various systems that are available. These notations will permit the reader to refer to the appropriate section in Part II of the Handbook for specific details on a particular metal or mineral. The equipment used to accomplish the desired unit operation is de¬scribed. Comparative data are presented to illustrate performance characteristics of unit operations, process, and equipment. The economic efficiency of individual processes is outlined. Some of the chapters contain material that is covered in detail in other sections of the Handbook Such chapters are developed only sufficiently to indicate the specific application of the techniques to hydrometallurgical processes. In this section considerable cross-referencing to the other related sections has been done.

Jan 1, 1985

By H. Sevim

In this paper, the research effort in simulating the operation of underground coarse-coal hydrotransport systems (UCCHS) is summarized. The equipment of the system to be simulated is already optimally selected by using an analytical optimization model. The purpose of the simulation model is to test the performance of the system and to obtain the distribution of the operating parameters such as water and power consumption, amount of slurry delivered to the preparation plant, etc. Knowledge of the distribution of these parameters is essential for the efficiency of the design and the operation of the system.

Jan 1, 1985

By Steve Karl, Rock Jenkins

The mining industry appears to be slowly rebounding. But many individuals and company officials are still smarting from the beating they received during the recent recession. As a result, companies have taken the "lean and mean" approach. As pointed out at the Oct. 24-26, 1984 SME-AIME Fall Meeting in Denver, CO, companies are placing more emphasis on optimizing their operations through more efficient mining and processing technologies and equipment. Empathizing with the mining industry&apos;s woes was the meeting&apos;s welcoming luncheon speaker, John D. Withrow, Jr., executive vice president product development for Chrysler Corp. Withrow paralleled Chrysler&apos;s problems of a few years ago with the current problems facing the US mining industry. He said Chrysler&apos;s come-back centered around its engineering and technical personnel, who regained "their seat at the head table." "In short," Withrow said, "we had lost the competitive edge. By cutting costs and people and improving our products we got everybody to believe we could." The 2700 participants at the Fall Meeting attended technical sessions geared toward turning mining back into a productive and profitable industry. Sessions and symposia included papers on precious metals extraction, crushing and grinding innovations, geomechanics, environmental control, health and safety, and various commodities. This article briefly highlights some of the papers presented. To order preprints of these technical papers, see ME, December 1984, pages 1620 and 1621. Computers Gain Mining Acceptance High tech has reached mining. As evidenced by many papers, computers have become valuable tools in many applications. These include tailings ponds operation and waste management; truck dispatching; mine design, simulation, and scheduling; monitoring; and reclamation. Mine planning is generally labor intensive and requires a considerable amount of the planner&apos;s time. P. K. Chatterjee, X. Chung, and Y. Jianjy described a computer-generated interactive graphics approach to under-ground coal mine planning that lessens the manhours involved in producing plans. The computer program examined exploratory borehole information. This included coal seam thickness, tonnage, quality constraints, and the nature of their distribution. Layout designs were then initiated and a probabilistic simulation performed to determine production levels of different extraction strategies. The interactive graphics approach gives planners the ability to quickly evaluate several layout alternatives and select the best one. For surface coal mines, M. A. White, of Arch Minerals Corp., explained several computer programs that aided in his company&apos;s surface mine plans. Several drill hole database and modeling pack¬ages are available. But Arch tech¬nicians developed specific pro¬grams for model strip areas. They were used to form long-term pro¬jections for various area and semi¬area stripping operations. They also generated reports on yard¬age, tonnage, quality, and ratio in¬formation. The information is used in budgeting, to compare mine plans, and to analyze acqui¬sition candidates. While computer-based truck dispatching systems have been used in mining for some time, earlier systems were run on ex¬pensive mainframe or high per¬formance minicomputers. As such, computer-based truck dis¬patching systems have been too expensive for all but the largest mines. Recently, however, a microcomputer-based system, af¬fordable to smaller mine opera¬tors, has become technologically feasible. Y. C. Kim and W. E. Kolb re¬ported on a simulated microcom¬puter system that uses strategi¬cally placed signposts in the pit area to automatically detect truck movements. A microprocessor in the signpost sends information to the microcomputer. The computer determines the truck&apos;s assign¬ment and alerts the dispatcher. He radios the driver his assign¬ment. In addition to the technical pa¬pers, an introductory short course on microcomputers was offered at the meeting. L. M. Kass and J. P. Stone, from the US Bureau of Mines, walked participants through the uses of microcom-

Jan 1, 1985

By F. B. Micheli

Introduction and Historical Background Although both sluices and devices using a simple flowing film are among the oldest known methods of concentration, they are still extensively employed in a variety of situations where they are not only efficient but also have a low operating cost. More particularly, they are valuable for making a bulk concentrate of high specific gravity minerals from alluvials and beach sand and in upgrading low value ores. The antiquity of some of the basic concepts can be seen in the fact that they are found in Agricola&apos;s De Re Metallica which was published at Basic in 1546, while in 1602, Carew114 gave a fairly clear account of tin ore dressing in Cornwall in which grass turves were used to catch the cassiterite. This is perhaps one of the forerun¬ners of the blanket strake. The planilla of Mexico, the lanchute of Malaysia and the old Cornish box huddle are also descended from these early strakes. In fact, a sluice with holes in the bottom for concentrate discharge was shown by Agricola, not unlike the principle used in the plane table and the lamflo sluice. The convex huddle for the treatment of sandy material appeared about 1848 and the concave form eight to ten years later. For the treatment of "slime" sizes, wooden dead frames which were manually worked were used in Cornwall for many years but gave way to the automatic water-operated type in 1860, and even a mechanically tilted frame was described by Henderson115 in 1857. Theoretical Considerations The behavior of solid particles in suspension depends to a great extent upon the pulp density and the size of the suspended particles. In a fairly dilute suspension, such as that normally used when dealing with small particle sizes, the behavior of particles in a flowing film results from two effects. These are the lateral displacement, which is determined by the time taken for each particle to penetrate the flowing film and reach the solid surface, and the resistance offered by each particle to further displacement after it has reached this surface. The initial penetration through the flowing film depends on the size and specific gravity of the particle and the thickness and viscosity of the film. As a result the smaller particles will migrate further before their movement is retarded relative to larger particles of the same specific gravity. The behavior on reaching the solid surface de¬pends on whether there is a single particle layer or, as is more often the case, a multiple layer or thin bed of material which is sufficiently dilated, permits the penetration of higher specific gravity grains. Thrust of Flowing Films. When a thin film of liquid flows over a plane solid surface, the layer next to the surface remains at rest but the velocity of the film increases with the distance from the surface and becomes a maximum near, but not quite at, the free surface. Therefore, a particle in suspension in such a film is acted upon by a greater force near the upper part of the film than at the lower part, resulting in an overturning effect. After a particle reaches the separating surface or an accumulated densely packed bed of other particles, the liquid flow causes it to move downstream by rolling, sliding, or by a movement involving alternating suspension and deposi¬tion (saltation). In rolling and sliding, which are brought about by a substantially noneddying stream, the large submerged particles are acted upon to the greatest extent and they move more rapidly than smaller ones, notwithstanding their greater mass. When two particles of the same size but of different specific gravity are considered, the higher density one moves more slowly by reason of its greater mass. As a result the particles tend to become arranged in the manner shown in Fig. 29. If any particle is so large as to stand above the water surface, the transporting force on such a particle, although the maximum available, will have less effect than that on a submerged one. Such large grains are therefore carried a lesser distance. Fluid Velocity in a Flowing Film It can be shown that if y is the distance within the flowing film from the interface, the fluid velocity v&apos; at this point is given by IIn this equation p&apos; is the fluid density, g the acceleration due to gravity, a the viscosity, a the angle made by the film to the horizontal, and 0 the film thickness (in cgs units). Furthermore, the volume Q of fluid per unit time and unit width is related to the film thickness and can be calculated, since which upon integration gives Consideration of the velocity v&apos; (Eq. l) and the terminal falling velocity µ derived from Stokes law enables the horizontal travel dz in time dt to be calculated as follows: Again integration and substitution of Eq. 3 gives In this equation, z is the distance travelled before a particle of density p at the top of the fluid film has settled on the concentrating surface. From these expressions it can be seen that the depth of the flowing film varies as the cube root of the volume of fluid and inversely as the cube root of the sine of the plane surface inclination. Similarly the distance a particle can travel before reaching the surface is directly related to the quantity of fluid and its viscosity. The viscosity of pulp is greatly increased by the presence of near colloidal particles and consequently the penetration of the somewhat larger grains through the flowing film is retarded, resulting in them being carried further across the concentrator deck. Obviously this effect can be reduced by prior removal of some or all of the ultra¬fine particles. The detrimental effect of kaolin on the separation of fine ferrosilicon from quartz has also been demonstrated by Johnston,116 the relationship between viscosity and efficiency of separation being shown in Fig. 30. The pH value also has a very marked influence on the viscosity and the use of acid mine water, for example, can increase viscosity materially and thereby result in lower efficiency. Dilation of Multi-Particle Systems Except during washing (when a single particle layer may exist) concentration usually takes place in a bed of particles which is partially dilated or stirred by eddy currents. The extreme case is seen in various forms of the sluice where the flow of water and the presence of riffles combine to create a fluid bed in which reverse classification takes

Jan 1, 1985

INTRODUCTION From its beginnings in the first decade of this century, flotation has gradually moved to a predominant role in mineral separation. There are several reasons for this, the continuing trend toward treat¬ment of lower-grade and more finely disseminated ores being the major one. Not only has this been true for sulfide ores to which the process was first applied commercially, but also for most nonsulfide ores as well. A second factor has been the broad applicability of the process with respect to particle size; it is effective from 8 to 10 mesh to below 10m. Finally, more so than for any other separation process, flotation has almost no limitations in separating minerals. Gravity, magnetic, or electrostatic processes are either applicable to particular minerals, or to a restricted number of mineral combinations. Flotation, on the other hand, can utilize the wide range of surface chemical differences among minerals, and an equally wide range of reagents. The recent availability of selective flocculation capabilities on a commercial scale as an adjunct to flotation should remove one of the limitations to the process in the very fine particle range. History Although flotation was anticipated in a 19th century patent to Haynes, its first significant industrial uses were in the early 20th century in Australia. According to Hoover,&apos; the Pottter-Del-prat pro¬cess had a "measure of success" at Broken Hill&apos;s Block 14 mine in 1905-1906, and was definitely successful at the BHP Mine, where it produced 80,000 tpy of zinc concentrates. Both the Mineral Separa¬tion and the Elmore processes had early trials in Australia also, with both successes and failures. The first application in the United States was in 1911, when the Hyde process was used by the Butte and Superior Copper Co. on a zinc ore in Montana. By 1916 Hoover could list 46 applications to copper, lead, and zinc ores, mainly in the United States. Ten years later Taggart2 listed almost a thousand patents covering processes and reagents which with few exceptions laid the foundations for modern practice. Included were: sulfidizing of oxides; leach-precip¬itation-flotation; cyanides, sulfites, sulfides, and oxidants for selective depression of sulfides; starch, tannin, and glue as depressants; and xanthates, dithiophosphates, and oleic acid as collectors. Within an¬other 20 years, all of these were in commercial use along with amines for floating silica from phosphates, and synthetic frothers were com¬peting with pine oil and cresylic acid. Flotation machine development followed a different course. Of the 170 patents listed by Taggart in 1927,1 those incorporating film and oil flotation-about a third of the total-were no longer then

Jan 1, 1985

By Charles R. Garrett

The American Borate Company, a wholly owned subsidiary of the Owens Corning Fiberglas Company under a management contract to the Hanna Mining Company, owns and operates an underground borate mine in Death Valley, California. The mine, named the Billie Mine, is located 24 km (15 miles) southeast of Furnace Creek along Highway 190. The ore body is under Death Valley National Monument with the major portion of the surface facilities located just outside the monument boundary. (See Figure 1.) The Billie Mine produces approximately 227 000 metric tons of crude ore per year. About 65% of finished product is supplied to Owens-Corning, the remainder is sold to other fiberglass producers. Geology The borate minerals in the Billie ore body were deposited in the lower main member of the Furnace Creek Formation, which is Pliocene in age. The ore body is thought to have formed from volcanic springs in or near a small lake basin. The deposit is essentially a limestone breccia that is permeated with borate minerals and surrounded with limey lake bed mudstones and shales. The ore body is mineralized with two main borate ores, colemanite and probertite. A third borate ore, ulexite, mainly occurs in the upper part of the ore body. The original mineral of deposition is thought to have been ulexite. Ulexite is a sodium-calcium borate hydrated with eight molecular waters. Due to heat and pressure from burial by later sediments, the ulexite had water forced out of its structure and recrystallized as probertite. Probertite is another sodium-calcium borate, with five molecular waters. Colemanite formed when surface water seeped into the prober-

Jan 1, 1985

By Don Rose

INTRODUCTION A number of tunnels supported and permanently lined by steel-fiber-reinforced shotcrete (SFRS) have been built in North America in the 1980s. The material is more economical than, and technically equal or superior to, conventional shotcrete using wire mesh. The design and construction of SFRS-lined tunnels is straightforward, and only a few new design principles, laboratory tests or construction equipment modifications appear necessary in order to use this material. Modern tunnel Contractors may use cyclic drill-and-blast methods on some tunnels, with intermittent shotcreting as part of an orderly cycle. The Dry Mix method is most suitable for cyclic, intermittent, relatively small-scale shotcreting. However, modern Contractors excavating tunnels continuously using large long Tunnel Boring Machines (TBMs) or Roadheaders may prefer Wet Mix shotcreting on a mass production basis. In either case, the use of steel-fiber-rein¬forced shotcrete (SFRS) promotes the rapid and economical excavation of tunnels. The addition of microsilica will improve SFRS properties and reduce rebound, and is expected to become standard practice with SFRS in North America, as it now is in Scandinavia. HISTORICAL REVIEW Steel-fiber-reinforced shotcrete (SFRS) at the present time (1985) is essentially conventional shotcrete with straight or deformed steel fibers added, and in general SFRS for tunnel linings encounters the same problems that conventional shotcrete does. Shotcrete history is well known. The use of sprayed plaster on wire frames for mounting animal skins by Carl Akeley of the Smithsonian

Jan 1, 1985

By E. J. Onuscheck

Coal mine safety of the past was plagued by disasters that took the lives of thousands of miners. Through the years new mining methods, improved laws, and a commitment from the mining industry has reduced the frequency of such incidents to a minimum. History tells us that coal was mined in the early 1700&apos;s in Virginia primarily for use by blacksmiths -- most of that mining was done in the Richmond area. It was in those mines that methane was encountered; as workings became more extensive, methane explosions became more frequent. In the early 1800&apos;s the first recorded explosion occurred near Richmond, Virginia -- 40 men were killed.

Jan 1, 1985