Search Documents

By S. Dempsey

Since its passage in 1872, the Mining Law has been modified on several occasions to meet the changing needs of America's society and economy. Despite its evolution, the Mining Law continues to be criticized as outdated. This paper briefly traces the major points in the history and evolution of western mining laws, and reflects on the current status of ongoing discussion to reform the 1872 Mining Law.

Jan 1, 1997

By M. W. Rutland, E. Manev, R. J. Pugh

Data collected from several different fundamental surface chemical techniques were compared to study the interfacial interactions in the dodecylaminelmica flotation system. In the present study, the method used was the microinterferometric free foam film technique of Scheludko (1967) in which the stability, thickness and interfacial potentials at the air/dodecylamine solution interface were determined. These results were compared to previously published data, obtained from surface force measurements (Rutland et al. 1992), in which the interaction and hydrophobic adhesion (pull-off force) between molecularly smooth mica sheets in the amine solution had been reported. Also equilibrium contact angle measurements were used for comparison. The data was collected over a range of pH values and related to the batch flotation response of mica in dodecylamine solution. It was found that maximum flotation occurred at pH 8, but this did not correlate with the minimum in double layer interaction potential. However, it appeared to correspond with a tightly packed collector monolayer giving maximum hydrophobicity to the mica surface. Finally, from the extended DLVO theory, it was shown that heterocoagulation between the bubble and the mica could only occur, providing there was a very long range hydrophobic interaction force to counterbalance the repulsive van der Waals and electrostatic forces.

Jan 1, 1995

By Heinz Petry

In deep strip mines the job of moving overburden may be so much bigger, and more costly than the removal of coal or ore that the operation is often called dirt mining. Constant improvement in stripping machines and techniques of using them is needed to offset rising costs and to increase production in mines that are now operating, and to make it economically possible to work deeper or thinner deposits.

Jan 1, 1962

By R. P. Proulx

The Meikle Mine is a high grade, underground goldmine utilizing primary-secondary longhole open stoping with delayed backfill to produce 2700 tpd(3000 stpd) of ore. Hot and reactive ground conditions were encountered early on in the mine life. Ground temperatures up to 166°C (330°F) were measured. In the early stages of mining, the mine experienced premature detonations using different explosive products. The learning curve to safely mine this high-grade gold deposit in hot and severely reactive ground was indeed very steep. Currently, the Meikle Mine uses a special buffered bulk emulsion in all blasts to address hot and reactive ground concerns. In addition, exacting procedures are also followed to ensure safe work with explosives. The combination of new explosives technology and strict loading procedures permits high mine productivity with the highest degree of safety.

Jan 1, 2000

By D. A. Saint Don, M. Prueher, S. Barnwell

With the current changes in technology, multiple methods are now available for aggregate resource identification. From Sonic to Coring, Reverse Circulation to Percussive, there are many choices to make regarding drilling technology. The discussion will outline the methods above with focus on aggregate investigation and highlight the new technologies that will make a difference in your search.

Jan 1, 2004

By David K. Sitler

Continuing advances in manufactured diamond materials used in rock cutting tools have created a new generation of high production tools for mining. This paper will review the three major manufactured diamond products available for the mining industry as supplied by General Electric Company, Specialty Materials Department, and examine the ways in which these materials are employed. As an integral part of this examination, the economic impact of manufactured diamond tools will be evaluated. Time and again, one will find that the premium price of these tools is economically justified when compared to traditional tools.

Jan 1, 1985

By W. Todd

The Robbins Company has developed a boring machine, with a rubber packer serving as the gripper system, for blind boring of raises without using drill pipe. This machine is the BorPak and has many applications for use in the mining industry which will improve productivity. In addition to the cost savings, the boring method will lead to increased safety in constructing blind raises. The advantages of using the BorPak in a mining environment will be discussed together with possible applications.

Jan 1, 1994

By John D. Gardner

This paper describes a process which finds the maximum worth of a mineral deposit. The procedure requires two phases. The first uses a microcomputer evaluation model to find the optimum design input, with minimum attention giving to actual mining constraints that might exist. The second phase runs the first-phase design parameters through a direct simulation model on a mainframe computer. In phase one, financial, economic, and geotechnical data are entered; and an idealized list of design parameters is output. The list includes optimum values for cutoff grade, mine life, mine size, paytons, paygrade, and payvalue. In addition, the model generates pro forma operating and cash flow statements and it indicates the maximum net present value (NPV) possible for the deposit along with the probability of that oc¬curring. The initial results imply perfect mining conditions. In phase two, when actual mining selectivity, sequence, and other practical design considerations are related in a direct simulation model to the optimum criteria found above, the maximum NPV invariably decreases. However, if it is still satisfactory (NPV greater than or equal to zero) then the maximum worth/ optimum design have probably been found in the first iteration. If, on the other hand, NPV is now unsatisfactory, then design compromises must be made and simulated, and the results rerun through the evaluation model. If several iterations fail to yield a positive NPV then the deposit is most likely unfeasible t for the forecast economic conditions used in phase one.

Jan 1, 1986

By Jacques Mongrain, Serge Barbeau, Gary Brierley

The Communaute Urbaine de Montreal is currently involved in construction of the South Interceptor which consists of 53 kilometers (33 miles) of 1,800 mm (6.0 ft) to 5,400 mm (18.0 ft) diameter tunnels for the purpose of collecting, storing, and delivering sanitary and combined sewage to the treatment plant. Work is divided into ten separate contracts; nine of which have already been bid. The purpose of this paper is to describe construction activities that have been performed through the end of 1986 with emphasis on a general layout of facilities, a summary of subsurface conditions, and brief descriptions of actual construction activities for the six contracts where tunneling has been performed. All projects are being excavated with tunnel boring machines.

Jan 1, 1987

Ravensthorpe Nickel Operation (RNO) is a major new mine and processing plant currently being constructed by BHP Billiton in a ?green field? site near the small town of Ravensthorpe, about 150 km west of Esperance and six hours drive from Perth in Western Australia. Ensuring that the project has a positive overall impact on the surrounding region and that this extends well beyond the life of the operation will be a major challenge for RNO, state and local government, and the local community. For the last two years, the Centre for Social Responsibility in Mining (CSRM) has been assisting RNO management and the RNO Community Liaison Committee to develop a community sustainability monitoring framework for the project. This paper reports on the process that was used to develop the framework, describes the main elements and briefly discusses key learnings from the exercise.

Jan 1, 2007

By J. B. Pateiro Fernandez, S. Möllerherm, E. Drüppel

"Since 1997 the Institute of Mining Engineering 1 at the Aachen University is dealing with the concept of sustainable development in the mineral industries. During this time it has conducted several research projects in this field. Its latest project is on the development of sustainability indicators for the German mineral industry. This paper describes some results of this project. A process chain analyses have been carried out identifying economic, social and environmental effects of the minerals extraction. Thirty indicators reflecting the particular conditions in the mineral industry have been designed. One important challenge was the design of quantifiable indicators taking into account the life cycle of a mining operation as well as mineral beneficiation and enrichment of the raw material."

Jan 1, 2005

By J. J. Carlson

Studies were carried out to determine whether filtration rate changes observed in an iron ore concentrator were due to variations in particle shape. It was confirmed that ores mined from different locations differed in filtration rates by as much as 60%. However, when image analysis was used to quantify the shapes of the individual particles in the filtration feed, it was found that the particle shapes showed almost no variation, and the shapes did not correlate with the filtration rate. It was also determined that the filtration rate variations were not caused by changes in particle size distribution. These results suggest that the differences in filtration rate are due to factors other than size and shape, such as surface chemistry.

Jan 1, 2008

Coal-derived flue gases contain CO2/SO2 and these contaminants preferably have to be captured by cheap sorbents. This remediation approach is from the standpoint of addressing issues such as global warming, acid rain and development of Advanced Power Generation Systems and to realize the economic gain as well. Conventional and existing dry scrubbing technologies use regenerable sorbents which are pollutant specific and require expensive stabilizers in order to attain versatility. This paper discusses the use a novel class of sorbents prepared from the heavy metal contaminated Berkeley Pit water (Butte, Montana) by a proprietary process developed at The University of Nevada, Reno. These sorbents are activated mixed spinel ferrite (MxFe,_X04)' Preliminary experimental results show that the sorbents have good desulfurization and CO2 decomposition capacities. The decomposition effectiveness of these mixed spinel ferrites was studied at 300°C and compared against the synthetic magnetite obtained from ferrous sulfate solution in our laboratory. The results indicated that the mixed spinel ferrite had good affinity for the adsorption and decomposition. The CO2 decomposition data of both sorbents fitted the first order reaction kinetics. Even though the surface area of the magnetite was higher than that of mixed spinel ferrite, the CO2 decomposition rate of the mixed spinel ferrite was estimated to be 2.5 times higher than that of magnetite under identical conditions. The carbon analysis deposited on the sample indicated that the CO2 was 100% decomposed into carbon and other carbon! hydrogen compounds by the mixed spinel ferrite whereas the conversion was 43% by the magnetite. In terms of specific adsorption of carbon, ferrite was 3-5 times more efficient than magnetite.

Jan 1, 1996

By A. Yazadni-Chamzini

Risk ranking of projects is one of the importance parts of the complicated risk management procedure. Recognizing the riskiest criteria enable the managers to plan for risk reduction. The first stage for meeting this aim is defining the risky parameters and then working to establish order between them. There are variety methods for risk ranking. The ELECTRE method is one of the best among the multi criteria decision making methods. In this paper with implementing the fuzzy ELECTRE, The risky criteria in the Tehran Subway project are being ranked. The result of this research presents damage and accident of machineries as well as the lack of labor and equipment safety is located in the first order. Collapse factors and local prices are in second rank. Also wrong design, pollution, urban facilities damageable are in third to fifth respectively. Delay and ? are located in the last positions.

Jan 1, 2012

By Wern-ping (Nick) Chen

The Florida Department of Transportation District 6 (FDOT D6) began a study in 1987 for a master plan to improve the traffic circulation and congestions between the Port of Miami (POM) and downtown Miami, FL. This study included a tunnel connection between two man-made islands, the Watson and the Dodge islands. Though a finding of no significant impact (FONSI) was completed in 1992, the project remained on hold for about 10 years. In 2002, Florida Turnpike took over this project, re-evaluated its benefits to the lo-cal communities, determined its feasibility (specifically the tunnel options) and established a probable cost. In 2005, the FDOT D6 regained its charge over the project and concluded that a bored tunnel under Biscayne Bay is feasible. Its primary components are: ? Widening of the MacArthur Causeway Bridge, to accommodate truck traffic to the Port of Miami. ? A tunnel connection between Watson Island and Dodge Island, where the POM is located. ? Connections to the POM roadway system, either for the traffic from the city of Miami or for the truck traffic from I-395 to the POM. The project will improve access to and from the POM and provide a dedicated roadway connector linking the POM with the MacArthur Causeway (State Route 41/1) and I-395, specifically for the trucks in and out of the POM without going through downtown Miami. As identified in the project information memorandum (PIM), its primary objectives are to: ? Improve access to the POM, helping to keep it competitive and ensuring its ability to handle projected growth in its cruise and cargo operations. [ ] ? Improve traffic safety in downtown Miami by removing POM traffic, trucks and buses from the congested downtown street network and, in doing so, facilitate ongoing and future development plans in and around downtown Miami.

Jan 1, 2009

By H. Wesley Peirce

Arizona, in 1966, has continued to be the site of an extensive and intensive search for metallic mineral deposits. Over fifty separate entities--companies and individuals--have been actively engaged in mineral exploration programs, both large and small, in the Basin-and-Range portion of the State. Certainly, copper has been primarily responsible for the major efforts, although associated gold, silver, and molybdenum mineralization also has been important in the economic evaluation of potential copper deposits. It is not difficult to explain why the Basin-Range portion of Arizona is receiving such attention. Part of the story, undoubtedly familiar to most, can be illustrated by reference to three graphical presentations. For example, Figure 1 shows Arizona's annual copper production for the period 1955-1965, inclusive, and it demonstrates that new records of production have been accomplished in each of the past 6 years and in 9 of the last 11 years.

Jan 1, 1967

By V. I. Ryaboy, V. A. Luknitsky, V. V. Zuyev

The action has been studied of three types of reagents used as intensifiers in grinding copper-molybdenum, sulphide-sheelite, polymetallic and other types of ores, namely N-donor, dispersant, and surface-acting agents. It has been proved that, depending on the type of ore treated, the C (N-donor) and C-170 (dispersant) reagents increase the yield of the principal size fraction of 0.074mm by 8-16% (relative). Consequently, the specific mill capacity improves by 13-21 %. The C and C-170 reagents activate the subsequent flotation stage and are thus beneficial to the mineral recovery. The surface-acting reagents affect the mineral grinding process to a lesser extent. The intensifying action of the reagents is attributed to the effective crushing energy decrease (lower crack-resistance factor) or else to the slime-dispersing effect of the reagents. The pilot-plant test results for the C reagents are given. Both C and C170 reagents are commercially produced and recommended for use at a number of concentrators in Russia, Uzbekistan and Kazakhstan.

Jan 1, 1995

By John L. Halls

INTRODUCTION In this section, it is assumed that the reader is an engineer with sufficient training in underground mining work, preferably with budgetary control, to understand the mining methods outlined in other sections of this handbook. The mining-method descriptions are not repeated herein; only sufficient information is provided to enable the reader to comprehend the development of the costs presented. All costs are in 1977 US dollars, except where explicitly stated otherwise. CAPITAL INVESTMENT The capital investment in the underground mining portion of any mining property includes the following: 1) The development of original access involving adits, shafts, declines, etc. It includes the necessary equipment for transporting men, materials, and rock. 2) The purchase of mine equipment including loaders, underground haulage equipment, fans, pumps, electrical distribution, surface facilities associated with the underground mine, etc. 3) Sufficient preproduction mine development to assure steadily increasing production after startup. De- pending upon the mining method used, the preproduction development should provide a supply of three months to one year of ore that is developed and is ready to be stoped. Underground development also includes excavations other than shaft stations, loading pockets, sumps, etc., which usually are associated with the means of access and are excavated by the contractor. These excavations could include a crusher cavern, an ore- storage pocket, and underground workshops that may or may not be included by the shaft-sinking contractor. Portions of these could be delayed until after production begins, but it is preferable to complete them during the development phase, so there is no interference with the production buildup. 4) The staff and labor costs for all phases from inception through final production. 5) The provision of mine-surface equipment and facilities strictly applicable to the underground portion of the operation. The required facilities include a changehouse with a lamp room, a first-aid station, compressors, an electrical substation, workshops, a ware- house, water pipelines to the concentrator, water storage tanks, explosive storage, etc. A concrete-batch plant, a sand-fill plant, and boilers for heating may be required. 6) Other direct and indirect costs. 7) Engineering, design, and procurement costs. 8) Contingency allocations. 9) Contractor's fees, startup costs, and owner's costs. Original Access As part of a study for the US Bureau of Mines, Dravo Corp. conducted an extensive literature research survey covering underground operations in the United States between 1963 and 1973. Table 1 is compiled from the section of that study pertaining to the types of access to underground mines. Table 1 does not include distances attributable to the deepening of existing shafts, nor does it include shafts bored by raise drills or downhole machines that need existing underground workings for the disposal of the cuttings. During the period under review in the report ( 1963 through 1973). concrete-lined circular vertical shafts were the predominant means of providing the first access to a new underground mine; these shafts accounted for 80% of the original access in terms of the number of accesses completed, and 75% in terms of the total verti- cal linear distances. The inside diameters of the conventional circular shafts ranged from 3.7 to 7.0 m (12 to 23 ft). Most (72% ) of these conventional shafts were for production,

Jan 1, 1982

By Jan Leja

Surfaces of metal sulfides react readily with selected constituents of environment. Two types of reaction products may form: (1) primary, chemisorbed and hydrophobic surface products or primary hydrophilic surface products, and (2) secondary reaction products -- produced during continued oxidation-reduction processes. For flotation, the chemisorbed surface product and the secondary reaction products, elemental sulfur or metal xanthates, must provide sufficient hydrophobicity of the surface to ensure particle-bubble attachment.

Jan 1, 1986

The bromine review did not arrive in time for publication in the June issue. Bromine production in the United States during 1992 amounted to 171 kt (376 million lbs), a 453-t (I-million lb) increase from 1991. Data compiled by the US Bureau of Mines indicates this increase was due mainly to greater exports of elemental bromine and bromine derivatives (flame retardants). Exports increased despite the economic slowdown in Europe and Japan. The United States remains the world's largest bromine producer, with about 42% of the total. Israel is ranked second, followed by the United Kingdom, the former Soviet Union and Japan.

Jan 1, 1993