Search Documents

By David Green

Power point slides

Jan 1, 2000

By Luis Elu, Andy Bolland, Jack Simmons

The gold refinery at Barrick Goldstrike Mines has increased production to more than 2,000,000 ounces poured per year while reducing the labor requirement. Safety and health has not been compromised with this increased production and in fact incident rates and exposures have reduced over the past five years. Streamlining procedures, improving ergonomics and the wise use of unique innovations has accomplished this significant achievement.

Jan 1, 1998

By H. W. Gussmann, R. G. Rohrs, E. van der Merwe

Salinity in Effluents carries a high penalty as a result of toxic­ity, corrosion, limited re-use potential, scaling and environmental impact. Although the high TDS, such as Calcium sulfate, other than metals are still being dealt with a low key non issue basis, they are receiving more and more attention from regulators. Traditional solutions to solve these problems are costly and inefficient and create therefore severe constraints on the prof­itability of mining operations and out-price in general the finan­cial resources for environmental clean up operations. Going up the technology versus cost curve the most econom­ic solution to pollution is dilution but which is difficult in a coun­t1y shoti of water. If this can't be done, the second best, at least in sunny areas, is, to pump the whole effluent on a tailings dam for evaporation. Depending on the contaminants, one may have to pond the efflu­ent to avoid re-dissolution and seepage into the ground. The next most common solution to pollution is the addition of lime to remove and concentrate any dissolved metals and then dump the product, hidden in a mass of gypsum in a convenient place. Again ponding may be required to avoid ground pollution. However the treatment costs start to rise steeply if it is not allowed to discharge the limed overflow solution because of its high calcium sulphate content. Further treatment is then required in the form of high cost and high tech membrane process tech­nology such as reverse osmosis or dialysis or even mechanical driven evaporation.

Jan 1, 1998

By David Wright, Colin Burns

Successful leaching of gold depends on appropriate chemical conditions; contact between leach solution and the gold particles; separation of the leach solution from the solids and extraction of the valuable ion from the solution. Irrespective of the leaching method employed the chemical conditions required are similar as is the dependence of solu­tion/gold contact on liberation. The various leaching methods available vary in the means by which gold/solution contact and solid/liquid separation are achieved. The essential difference between heap or vat leaching techniques and those involving agitation of a slurry is dependence on percolation for effective gold/solution contact. The most significant factor preventing uniform percolation is the presence of fines or clays. The quantity and character of the fines fraction is ore type dependent and may result from crushing, degradation during stacking or leaching, or the natural size distribution of the ore. The problems associated with fines can be aggravated during stacking and preparation of the heap. Segregation during stacking can result in concentration of fine particles at the centre of heaps. Further concentration of fines may also occur during irrigation by the movement of the fine particles with the solution. The end result is that the areas in which fines are concentrated become areas of low permeability. The contact between leach solution and the ore in such areas is, at best, slowed down dramatically and, in some cases, prevented altogether. The consequences of this phenomena are slow leaching and a reduction in recovery. The conventional solution to this problem is well known. Agglomeration of ore prior to heap leaching is practised widely. The effect of agglomeration is to immobilise the fines by causing them to adhere either to each other or to larger ore particles. The net effect is that the ore behaves as if no fines were present. The use of agglomeration is limited only by its cost, the most significant components of which are the cost of binding agent, commonly cement, and the capital cost of the agglomerating equipment.

Jan 1, 1995

By Ian Larkins

The Ruby Hill Mine agglomerates crushed low-grade ore (nominally -1 .5'') with high-grade filtered tailings (filter cake, nominally 80% -65#). Cement is added as a binding agent. The agglomerated ore is then conveyed and stacked on the heap. In 1998 approximately $480 000 was spent on cement for agglomeration. Cement for mill pH control and agglomeration was the largest single reagent cost at Ruby Hill. In an effort to reduce agglomeration costs a test-work program was initiated to investigate alternative binders and optimum binder additions. This paper summarizes the test­work results to-date.

Jan 1, 1999

By A. H. Reitsema, Hans E. van Dam

In CIP, CIL, and Heap Leach gold recovery operations, a sub-optimal activated carbon performance invariably causes a significant loss of revenues. In this paper it is shown, how dedicated analyses of carbon samples can be used as a guide in plant performance optimiza­tion. Firstly, a brief outline is given of the most important methods of analyses, including the specialized methods not normally used by mining operations, but provided by carbon manufacturers. Then, a number of practical cases are discussed in which carbon sample analyses provided insight which allowed significant improvements.

Jan 1, 1995

By H. G. Linge

The Australian gold industry currently contributes some $4bpa to the national economy [l]. Some 40% of the total gold is produced in the region centred on Kalgoorlie known as the Eastern Goldfields of Western Australia. This region is the largest single centre of production with an output of some 100 tpa of gold [2]. In the Eastern Goldfields, refractory arseno­pyritic gold ore is an increasingly significant source of gold, feeding several operations utilizing bio-oxidation as the pre­carbon in pulp/leach (CIP/L) treatment process [1]. This paper desribes an alternative pre-CIP/L treatment option for use in the Eastern Goldfields based on the chlorination of arsenopyrite by chlor-alkali technology [3] using the salt resources available from saline water present in abundance in the region.

Jan 1, 1995

By Richard M. Crowell, John W. Shield

GeoBiotics has developed a biooxidation technology (patents pending) which involves coating refractory precious metal sulfide concentrates onto a support material and biooxidizing the sulfides in a heap configuration. The concentrates are produced from low or high grade sulfidic refractory ores or existing mine tailings. The process has been found to achieve high gold recoveries asso­ciated with stirred tank biooxidation, but at the low operating and capital costs associated with whole ore heap biooxidation. Improved gold recoveries of up to 98% after biooxidation are reported for 4 representative mines or deposits. The sulfide flotation concentrates were studied using 3 and 6 in. diameter columns or 3 in. drained vats. The refractory sulfide concen­trates biooxidize rapidly in 3 to 12 weeks with substantial increases in subsequent gold recovery.

Jan 1, 1996

By Rosa H. Harris

The world's largest gold dump leach operation, Minera Yanacocha S.A., has installed community assistance programs in Peru concerned with health, education, electrification, agricultural assistance and road improvements. The programs are conducted in a joint venture fashion in association with various organizations.

Jan 1, 1998

By V. I. Lakshmanan, Chris Dodson

Refractory gold ores or concentrates are pretreated in general by physical, chemical and biological oxidative pretreatment processes prior to cyanidation for the economic recovery of gold. The thermal treatment processes generally include fluid bed pro­cessing(!>, chemical with pressure<') or atmospheric (Caro's< ·'>, 3 Nitrox1')) pretreatment leaching and physical with ultrafine grinding!"). Roasting and aqueous pressure oxidation pretreat­ment methods have several commercial applications (Homestake, Barrick) and biological oxidation methods have recently found industrial applications in Africa. The roast pretreatment methods to treat refractory sulphide ores or concentrates transform iron sulphides generally to a porous iron oxide matrix assisting the lixiviant cyanide to effectively diffuse the calcine for cyanidation and hence with improved gold recovery. Jha and Kramer<') made an extensive review of roasting chemistty and practice to tt·eat refract01y gold ores. Industrially two stage pretreatment roasting is generally employed. During the first stage roasting is carried out under oxygen deficiency conditions to provide a low arsenic calcine, mainly magnetite and in the second stage magnetite is trans­formed to haematite under oxidizing conditions.

Jan 1, 1998

By Ian J. Corrans, Gary Johnson, John E. Angove

Activox® is a hydrometallurgical process used to oxidise sulphide concentrates. The process is based on two relatively simple, established unit operations; i.e. fine or ultra-fine milling (UFM) and pressure oxidation under mild conditions. An under-standing of, and ability to control the pulp chemistry during oxidation has resulted in the successful Activox® treatment ( on a batch scale) of a wide variety of sulphide flotation concentrates; • pyrite/arsenopyrite + gold • pyrite/chalcopyrite + gold • pyrite/chalcocite + gold • pyrite/enargite/tetrahedrite + gold Oxidation rates are rapid (1-2 hours retention time) and gold

Jan 1, 1995

By Kevin Phelan, Gary Johnson, Peter Sperring

The vast majority of tailings in the Western Australian Goldfields are deposited in purpose-built storage facilities. At mine-sites with open-pit mining operations there is also the requirement to mine and stack large volumes of waste rock, usually into surface waste dumps. As these dumps have typically 30% of their gross volume present as voids, there is the potential to use this void space for the storage of tailings. The concept of co-disposal is to store the tailings material in the void space of the waste dumps, eliminating the need for a separate tailings storage facility. Dominion Mining Limited have been investigating the possibility of using co-disposal as a means of tailings storage. Laboratory testwork has been used to understand some of the issues associated with the concept, and assist in the design of an on-site demonstration of the concept. Co-disposal offers a number of potential advantages, and despite a number of practical hurdles to overcome, considerable economic and environmental benefits could be realised if this concept can be demonstrated on a commercial scale. The major advantage of such a system is to remove the need to build, operate and rehabilitate a separate tailings storage facility. Rehabilitation can be incremental throughout the mine life as the co-disposal site will be virtually indistinguishable from a current waste dump in both size and form. Other potential advantages include more stable waste dumps, less land area disturbed on the project site, and better water recovery from the tailings.

Jan 1, 1995

By Harold Wahlborg, George Owusu

In a study using butyl diglyme as an organic extractant, essen­tially complete extraction of gold from chloride leach solution was achieved. The extraction kinetics are so fast that the process could be completed in 30 seconds. Except for iron, co-extraction of other ionic species was insignificant. Co-extracted iron species were successfully scrubbed from the loaded organic using 10% HCl solution. High grade, >99.9%, gold was recov­ered from the loaded organic using 5% oxalic acid solution as the stripping agent at a temperature of 70°C to 80°C. Over 99% of the organic-loaded gold was stripped from the organic phase. The butyl diglyme extractant is being tested on a variety of gold-bearing feedstocks. Presented here are results obtained from two gravity concentrates.

Jan 1, 1999

By V. Fred Swanson, J. Patrick Glynn

The environment for process engineers today is very different from 20 years ago. The ideas and mathematical description of models for a multitude of different unit operations is an ongoing development. The computer tools to deal with the mathematics are readily available and specialist companies have developed, tested and verified their models. The challenge for the process engineer is to know which package to use and to know whether a particular application is the most accurate for the specific process. Metallurgical simulation programs today are well known and proven. Certain programs are specialized while others are broader based. The needs of each user are dependent on the application. Typically, most users require the following operations: • Comminution • Flotation • Hydrometallurgy • Pyrometallurgy • Additional requirements could be defined as: • Thermodynamic capabilities for solids, phases, and gases • Dynamic simulation • Data analysis tools • Coal oriented operations • Diamond oriented operations

Jan 1, 1997

By Timo Niitti

Within the minerals industry, flotation is the predominant method when processing sulphide ores. There is hardly any competition in this area because of the high efficiency and low costs of flotation. When processing other ore types magnetic or gravity• methods are commonly used and sometimes leaching methods are selected. The wide variation of the properties of gold (high value, low ore grades, softness, high specific gravity etc.) sets challenging requirements to the processing methods and particu­larly for flotation machines, which should be able to effectively recover free fine gold, coarse gold and gold bearing minerals throughout the full size range. In gold processes the amount of concentrate is usually low, but in some cases large amounts of gold bearing sulphides e.g pyrites has to be recovered. In gold processing seldom does only one method provide the optimum results, but the recovery is usually made using several complementary technologies: gravity separation, leaching and flotation are the most common ones. Mineralogy is the determin­ing factor when selecting the method or methods to be used.

Jan 1, 1995

By P. Gelfi, G. Hill, A. Showell, V. Martins, R. Dunne, R. Jenkins

Carbon attrition losses are not usually a prime consideration for CIP equipment selection and CIP plant design. However, the costs as a result of carbon attrition and associated gold lost with carbon can be high. Recorded carbon losses for Newcrest operating gold plants were shown to vary widely from plant to plant. The Tuckabiana plant recorded an overall loss of only 0.3g carbon /t ore which is very low by industry standards. A comparative carbon management study was undertaken by Newcrest to highlight the reasons for the excellent record of Tuckabiana operation compared to other Newcrest plants. This paper discusses the results of the comparative study and high­lights areas of concern with respect to carbon attrition.

Jan 1, 1995

By Ken Criley, Marc E. Orman

Identifying the optimum ultimate height for heap leaching ore requires the consideration of a number of competing factors. A primary limitation is the reduction in the permeability of the ore with increasing heap heights. At low permeabilities the heap can blind off, cause serious ponding and runoff, and become very difficult to rinse at closure. The authors present a laboratory methodology that has been successfully used on several projects to identify the maximum height for controlling heap permeability.

Jan 1, 1996

By Brian Carr, Craig Brewer, Jeff Grubbs

This paper examines the role of the StemTite Blast Control Plug in explosive energy confinement and explores the benefits of its successful application in gold and silver mining operations. Prior studies involving this device are consolidated.

Jan 1, 1999

By James P. Sabogal

A control and monitoring system is being developed by Betz Laboratories for the heap leach process in gold recovery. Called Betz 14000GL, the system is designed to improve gold leaching and provide savings in chemical consumption by controlling and monitoring key parameters in the heap leach gold recovery circuit. The system uses information from on-line sensors to control antiscalant chemical addition, pH and cyanide levels. The proprietary graphics and report features of the computer system allows the user to monitor and critically evaluate the performance of the process.

Jan 1, 1998

By John Frostiak, Igor Gonzales, Kenneth G. Thomas, Ken Manning

The Pierina deposit was acquired in August 1996 when Barrick Gold Corporation purchased Arequipa Resources, a junior mining company with extensive land positions in Peru. At the time of acquisition, Arequipa ha.d developed two exploration tunnels and drilled 9 exploration holes on the property. Metallurgical tests, conducted on samples taken from the tunnels and the exploration holes indicated that the ore was amenable to heap leaching. Barrick's exploration team recognised from the outset, the potential of the mineralisation and convinced Barrick's senior management that this was indeed a world class deposit that should be pursued. On November 25, 1998, the fi was poured at Pierina, 27 months from the time of acquisition. During that period BmTick completed its exploration programme, prepared a development plan including capital and operating costs, production profiles and cash flow forecasts, and a schedule to develop a mine and construct a leach pad and gold recovery plant, including all supporting infrastructure. All permits and environmental approvals were obtained and all necessary land was acquired. The project was completed on schedule and under budget. This was the first greenfield mine development for Barrick outside of North America. This paper details, mainly, the research and development, engineering, construction and commissioning of the metallurgical process facilities.

Jan 1, 2000