Search Documents

By W. J. Pennstrom, J. R. Arnold

Gold Fields installed what was the mining industry's first commercial gold electrowinning/replate circuit at Ortiz in 1981. Its highly successful operation since that time provided the design basis for a similar circuit at Mesquite, which was started in early 1986. These circuits produce plated gold foil suitable for direct shipment to a refinery or melting directly into bars. Detailed descriptions of the electro- winning and replate circuits are given and advantages and disadvantages are discussed.

Jan 1, 1988

By D. C. Sisti

A paper was presented during the 1970 SME Fall Meeting on the Stinson Preparation Facilities by representatives of Beaver Creek Consolidated Cool Company and Heyl & Patterson, Inc. This paper summarized a combined approach to development of a flow diagram and selection of cleaning equipment required to produce a uniform metallurgical coal at maximum recovery with special emphasis on sulphur reduction. These facilities were located in the Elkhorn. Coal Fields of eastern Kentucky and, in particular, the area of Wayland, Knott County, Kentucky, where approximately forty-five- million tons of Elkhorn No. 3 coal could he recovered. The facilities incorporated a Bradford Breaker for reduction of the ROM coal to minus 1-1/2 x 0, 6000 ton-raw coal storage, preparation plant, water clarification and thermal drying facilities, clean coal storage and a 4000 TPH unit train loading facility.

Jan 1, 1973

As ore deposits become finer grained the requirements for regrinding before cleaning or leaching have increased substantially. Despite this increasing need, there is no standard test to predict grinding energy requirement below 70 microns. The standard Bond Mill test applies for coarser ball milling, but is not appropriate for stirred milling with fine media grinding to 70 microns. With no industry -standard test, the energy requirement is often made on the basis of supplier estimates or benchmarking against similar applications. Yet suppliers use vastly different scale-up methods which result in widely different energy estimates. Estimates can differ by 100-300% even for similar mills. This must result in serious errors to install either too much or too little grinding power. This paper explores this by comparing the actual performance of full scale regrind mills against their original design estimate. It confirms that serious scale-up errors have been made, and have then been perpetuated by ?benchmarking?. The test conditions to achieve accurate power estimation are discussed. The essential test conditions are: continuous (not batch) tests, ensure steady state (no coarse fraction retained in test mill), correctly account for classification, measure energy directly (not inferred), and using the same media size as the full scale installation. Failure to correctly address even one of these factors can bias results by 40%; failure to address several multiplies the error.

Jan 1, 2011

By V. Roze, R. N. Parkinson, R. Shepherd

The alphaDOSIMETER is a complete, integrated system designed to monitor the immediate worksite of underground miners where the disintegration for radon daughters is a risk to the health of mining personnel. The dosimeter weighing little more than one pound is worn by each miner throughout the entire shift and is powered by the miner's cap lamp battery. After this integration period, the unit is connected to a reading network whereupon the day's data is dumped, calculated and stored. Beginning in July 1980, prototype units were subjected to vigorous underground testing in uranium mines in Canada and the United States and in tin mines in Cornwall, U.K. The testing results are summarized and proposals advanced for a typical mine monitoring system utilizing the alphaDOSIMETER.

Jan 1, 1981

By J. B. Rasmussen

As part of a purchase of a fleet of Caterpillar 785 trucks, Round Mountain Gold Corp., Cashman Equipment Co. and Caterpillar Inc. entered into a four-year contract for the major maintenance of the fleet of trucks. This contract includes fixed costs and guaranteed availability. The results have been excellent, and the fleet of trucks performs well. History The Smoky Valley Common Operation is a unique mine. Through a mixture of diligence and foresight, it has become the largest open-pit, heap leaching gold mine in the world. This was no small feat considering the remote area surrounding the mine. Round Mountain is located in north-central Nye County, NV. To the east of the town and mine lies the Central Toquima mountain range. To the west is the Toiyabe mountain range. Between them is the Big Smoky Valley, a flat expanse of sagebrush, salt grass and fine dirt.

Jan 1, 1991

To simplify programming, image analyzers commonly measure either linear intercepts or the areas of particles and grains to determine liberation based on polished section mounts. However, the concentration of minerals by flotation is based on reagents that interact with the exposed surfaces of the minerals. Thus, it is often perceived that image analyzers should measure the perimeter of the mineral of interest in the ore particles. A comparative liberation study of thirteen samples collected from a flotation plant processing a complex base metal sulfide ore showed that the liberation of the ore minerals determined by area measurements is very similar to the liberation determined by the exposed perimeters. The liberation determined by exposed perimeters is more appropriate only for those cases where the mineral texture is so complex that it is retained in the small particles generated in conventional grinding operations.

Jan 1, 2002

By H. Walqui, J. Drelich, J. Pletka, E. Luhta, E. Raber, J. Wieland, P. Boyd, N. Tervo, D. Herron, S. Boston

Mini-projects studying the flotation chemistry of paper de-inking were incorporated to an educational program at Michigan Technological University with support from the paper recycling industry. Interfacial activity of frothing agents, surfactants and polymers in de-inking flotation systems has been studied through flotation, atomic force microscopy, zeta potential, contact angle, surface tension, and froth stability measurements. These fundamental studies were developed to understand microscopic and molecular effects occurring in flotation of ink particles that may lead to improved designs in de-¬inking flotation processes. Fundamental studies indicate that ethoxylated alcohols are efficient frothing agents in flotation and can be used to clean the recovered paper from hydrophobic ink particles. Next, it was further supported in this research that the fatty acids activated by calcium ions act as collectors in flotation of ink particles. Finally, improvements in de-inking flotation are reported in laboratory tests involving aqueous solutions of polymeric flocculants.

Jan 1, 2001

By William C. Peters

The frustration encountered by exploration crews in connection with land acquisition could be graphed to show a correlation with the natural law that everything tends to become more so. Figure I shows a rather common, situation. The combinations of ingredients are almost limitless and the resulting brew is often poisonous to an exploration man. A single step, that of taking a series of deep soil samples is often delayed until some sense can be made from "floating" unpatented claims which are obscure in orientation as well as position, placer claims overlapping lode claims, location posts with empty Prince Albert cans, and claims with no apparent assessment work for ten years. Add to this some patented claims with¬out monuments, a state or federal withdrawal area which may or may not invalidate pre-existing claims, a loosely defined tunnel site, and some ranchers who understandably resent the separation of surface rights from mineral rights. The picture is familiar to exploration men. One approach to such problems is to ignore them until someone voices an objection -- but then an even more chaotic situation is likely to develop. Another practice is to stake new claims to cover all ground that is "open" at first glance and then find out if there are conflicts so that the new claims can be adjusted accordingly.

Jan 1, 1970

By Vas P. Srinivasa

A comminution circuit is an important integral part of a mineral processing plant. Nearly 40% of the capital cost and 30 to 40% of the operating cost are taken up by the crushing and grinding circuit. Therefore, considerable care should be given to the design and selection of this circuit. Several factors affect the selection of a comminution circuit--energy consumption, avail- ability of the equipment, the remoteness of location, and availability of trained personnel, to mention a few. Each of these factors influences the choice. Selecting a comminution circuit strictly on lower capital cost may not be optimal. Crushing and grinding circuits are usually site specific and should be selected - only after careful analysis of all the factors involved. The objective of this paper is to show the effect of these factors, which are extranious to capital cost. Usually, the capital cost of a semiautogenous grinding circuit is lower than that of an equivalent conventional circuit. However, due to lower equipment availability and high power costs in certain locations, the economic advantage of lower capital cost is lost. Analysis indicates that a break even point occurs at a power cost of 5¢/kWh. This paper describes the procedure utilized for selecting the most economic comminution circuit and states the conditions applicable for each cominution circuit.

Jan 1, 1983

By C. Y. Haas

Of all the industrial clay minerals, attapulgite probably enjoys the widest variety of applications. A review published over three years ago by Haden and Schwint (18) cited some 80 individual uses, a list which continues to grow. In its near half-century of commercial life, attapulgite has received a generous share of research study and patent development effort, both on the part of producers as well as consumers. This work has been divided between understanding the mineral's structure or properties and applying it to specific end-uses. Naturally, information gained from the former has pointed toward opportunities in the latter. References of particular significance are cited throughout the text. Attapulgite's variety of uses derives from the unique three-dimensional structure and needle-shaped particle form of this crystalline hydrated magnesium aluminum silicate. Its inherent colloidal and sorptive properties are well known, and distinguish it from its sister clay minerals. Attapulgite is characterized by its high surface area, porosity, sorptivity, and decolorizing power. Its slips or slurries are viscous and thixotropic, however, unlike bentonite are not flocculated by electrolytes. In Table I are compared the general properties of attapulgite, bentonite, and kaolin. The properties in Table I are documented in greater detail by the wealth of scientific literature which has been published on the composition (14)(15), structure (6)(16), surface (16)(4)(22)(24), adsorption (31)(4)(5)(25), rheology (10-11)(12)(13)(26)(27)(32), plasticity (30) (31), and chemistry (23)(3)(7) of attapulgite. Attapulgite is the principal mineral constituent (70 to 80%) of attapulgite clay as it is commercially produced in the Georgia-Florida area of the United States. As mined, this clay also contains 10 to 1S% montmorillonite, sepiolite, and other clays; 4 to 8% quartz, and 1 to 5% calcite or dolomite. (18) During processing, non-clay fractions are removed so that commercial products are enriched to 85 to 90% attapulgite. By wet processing (such as practiced in the

Jan 1, 1971

By John W. Rold

These encompass all adverse effects of oil shale mining, processing, and ancillary developments on the environment. Specific problems concern: land, vegetation, wildlife, water, air, population growth, aesthetics and public emotion; and fall into four categories of: land, water, air and emotion. Land includes excavations, spent shale disposal, loss of vegetation and impact on wildlife and domestic grazing, plant sites, buildings and roads, necessary urbanization and the total aesthetic or visual Impact. Water considerations are: requirements for Industrial and domestic supplies, adverse effect of underground water on mining, avoidance of pollution or adverse effect on surface or near-surface water, and the utilization or safe disposal of liquids. Air problems include dust, smoke and stack gas, Public emotional problems include reaction to the above problems, and misconceptions of oil shale country and an oil shale Industry. Government and industry are aware of the problems, and are seeking solutions. Last year, the three affected states studied oil shale environmental problems and solution costs. Colorado estimated environmental costs would add approximately 7% to construction and 7% to operation. The report suggested research in: (1) Water availability and impact; (2) Disturbed lands revegetation and rehabilitation, including spent shale; (3) Environmental inventory and impact; and (4) Regional development and land use planning. Governor Love appointed a 47-person committee representing Industry, government and environmentalists to attack the problems. Research pro-posals were prepared to focus on each problem. $715,000 state, federal and industry money is being committed. Results should provide data for industrial solutions and equitable agency administration.

Jan 1, 1972

By William H. Pomroy, Annie M. Carigiet

This U.S. Bureau of Mines report is an analysis of underground coal mine fire incidents occurring in the United States during the 15 years from 1978 through 1992. The fire data used in this analysis were obtained from Federal Mine Safety and Health Administration (MSHA) mine fire investigation reports. Fires were analyzed by year, state, coal bed thickness, mining method, evacuation measures taken, ignition source, burning substance, location, equipment involved, detection method, time of day, number of injuries and fatalities, and method of extinguishment. In all, 164 fires are reported, or an average of 10.8fires per year. The most common ignition source was electricity, the most common burning substance was coal, the most frequent fire location was the belt entry, belt conveyors were the most common equipment involved in fires, and water was the most common extinguishing agent.

Jan 1, 1995

By G. Pierson

Explanations for commodity price levels (or movements) commonly focus on the fundamentals of supply and demand otherwise they are simply assigned to speculative activity. Comparisons of metal-price histories to monetary and other economic data support the argument that the supply of and demand for money are no less important in the determination of price than are the supply and demand of the commodity itself. That these relationships should exist is evident in the price identity and they are consistent with monetary theory. The patterns developed have limited usefulness as predictors, but their recognition is essential for the construction of price scenarios for planning purposes.

Jan 1, 1998

By Verne Huser

The intensity of environmental conflict, the delays and legal battles that have marked the 1970's suggest the need for additional processes to resolve environmental disputes. Our present means frequently fail to address the real issues separating individuals and institutions. They are primarily adversary processes that foster polarization and reduce cooperative efforts. At the Office of Environmental Mediation, we have no quarrel with adversary processes nor with polarization, for both serve as important spurs to necessary change. We do seek cooperation among parties at a point where there can be a realistic expectation of success in facilitating a resolution of their mutual differences.

Jan 1, 1979

By Fred L. Myers

The use of finite element programs for evaluating large grinding mill shells is becoming increasingly popular. However, large scale, detailed analysis can become a burdensome task when one is required to manually prepare the necessary data to be entered into the program, while evaluating the voluminous results is even more devastating. Although available computerized finite element analyses can reduce computation time from years to months or even weeks, additional pre and post processors can reduce the time for data preparation and result evaluation to hours, while simultaneously reducing the probability of human error. Examples of the uses of these processors are presented as well as typical modeling techniques.

Jan 1, 1979

By L. J. Dahl, S. E. Paulson, H. L. Kuhlman

To provide basic information on the processes occurring during in situ leaching, the US Bureau of Mines developed a geologic characterization research program. This includes laboratory experiments wing leaching apparatus that can accommodate whole core samples. Whole core experiments result in a higher proportion of ore mineral contact by the leach solution than packed column experiments. They also allow for the assessment of permeability changes taking place as the result of mineral dissolution, precipitation, and clay swelling within the flow channels of the rock. The leaching apparatus developed can be wed for either constant-pressure or constant- flow rate experiments and allows for the control of flow rate, pressure, and temperature during the experiments. Details of the experimental apparatus are presented, as well as preliminary results from the first series of experiments on an oxide copper ore from the Casa Grade, AZ area.

Jan 1, 1988

By S. C. Sun

The grinding of coals for coal preparation has been studied extensively by previous investigators, but no similar work has been done on coal lithotypes (l-4). However, the different natural breakage characteristics of coal lithotypes have been recognized and utilized by the coal industry (5,6) to develop the Longway Burstlein process (7) for the concentration of macerals(8). The specific objective of this research was to determine the relative grindability of lithotypes, obtained from both anthracite and bituminous coals. An attempt was made to relate the findings, wherever possible, to the chemical and physical properties of the tested lithotypes. Another aspect of this research was to ascertain the size distribution and grindability of lithotypes ground at a various number of revolutions in a Hardgrove mill.

Jan 1, 1970

By Ray E. Harris

A resource of 134,400,000,000 tons of minable trona and mixed trona and halite underlies an area of about 1,300 square miles vest of Green River, Wyoming (Culbertson, in preparation)(Figure 1). In 1982, the total domestic consumption of soda ash (refined trona) was 6,667,000 short tons (Kostick, 1983), approximately 90 percent of which came from Wyoming trona. This enormous resource occurs in the Wilkins Peak Member of the Creen River Formation (Eocene). The Green River Formation is derived from sediments deposited in a large lake (Lake Gosiute) that occupied the Green River Basin in south-western Wyoming 38-54 million years ago. The Wilkins Peak Member represents a restricted, evaporite-rich cycle of deposition during which time the trona deposits were formed. A total of 42 trona beds are known, of which 25 are of sufficient thickness and extent to be considered minable (Culbertson, in preparation).

Jan 1, 1984

By S. E. Phillipson, S. Romberger

The Late Miocene San Cristobal Ag-Zn-Pb deposit represents syngenetic and epigenetic mineralization with low- and high-sulfidation characteristics. The geology of the deposit is characterized by barren dacitic ring fracture domes, mineralized resurgent rhyodacite domes, strongly altered and mineralized tuffaceous lacustrine sedimentary rocks and an extensive crystal-lithic tuff debris apron. The orebody is hosted by intracauldron sedimentary rocks and breccias. Fluid inclusion data suggest that silver, lead and zinc were transported as chloride complexes and precipitated by cooling in veins from <5% (by weight) NaCl eq. fluids at 170° to 215°C. Silver spatially and perhaps temporally associated with resurgent rhyodacite was transported as a chloride complex and precipitated by increased H2S activity or increased fluid pH.

Jan 1, 2002

By J. Hanna, R. Kalathur

Over the years, Alabama&apos;s coal industry has generated, during mining and cleaning operations, about 150 million st of fine waste coal, with this total increasing at a rate of 2 million stpy. Reclamation of the fine-size wastes (containing 20% - 60% clean coal by weight) provides, free of charge, mined and crushed feed stocks for coal recovery. Also, the removal or recovery of pyrite from the tailings should eliminate a major source of acid-water pollution. Tests were made on the impounded wastes and current plant discharges to recover the coal fraction by sizing, gravity and flotation techniques. Gravity separation of the +100-mesh material produced commercial-grade coal averaging 7.6% ash, 0.8% sulfur and 13,471 Btu/lb. However, the coal yield, at about 31 % - 56%, was relatively low. Froth flotation, using mechanical and froth column methods, gave similar coal products at much higher coal recovery rates of 87% - 93%. This coal analyzed 10% ash and 1.1% sulfur.

Jan 1, 1993