Search Documents

By J. C. Irvine

A recent development in underground drilling has been the introduction of the down-the-hole drill, an old and very familiar tool to the surface operator. The idea of moving such a rig underground is not new. Tests were conducted at INCO in Canada and Mt. Isa, Australia in the early 1960's, and St. Joe used one for underground exploration in their Missouri lead mines in the mid-1960's. However, the trend to full scale production programs did not start until the mid-1970's. The first successful North American test was at INGO in early 1973. This led to a large-scale pillar recovery and open stoping program which en¬compassed 25 drilling units by mid-1976. Meramec Mining Company tested a unit using air boosted up to 200 psi (140, 000 kg(m2) in the summer of 1973 which by 1976 led to an open stope and pillar drilling program using 12 units. By mid-1976, production units using boosted air were also in use at Pilot Knob in Missouri and at St. Joe in Balmat, New York. Experimental and utility units were in use in several other mines and down-the-hole drills were being seriously considered for at least one major new underground mine.

Jan 1, 1976

By G. T. Adel, P. E. Richardson, R. Pazhianur

Cathodic protection using impressed current was employed to reduce mill wall wear during ball milling. Wear rates were determined from weight-loss measurements made on four 1-in.-diam mild steel coupons that were installed flush with the interior surface of the mill wall. Grinding tests were conducted on quartz, pyrite and quartz-pyrite mixtures at pH levels of 4.6, 7.1 and 9.2. Cathodic protection was shown to reduce mill wear by 30% to 60%. An examination of the coupon surfaces using scanning electron microscopy showed that cathodic protection greatly reduced pitting corrosion. The presence of a sulfide mineral, such as pyrite, was found to increase the wear rate significantly, possibly due to galvanic interactions. It was also found that the wear rate is significantly higher than the sum of abrasive wear and the corrosive wear, due to a synergistic effect.

Jan 1, 1998

By M. G. Bakker, D. D. Murphy, D. R. Spears

The US Bureau of Mines studied the mechanism of shear flocculation of silica with stearic acid. At pH 6 and 12, shear flocculation of silica was not observed with the addition of up to 4.5 x 10-4 M (5 lb/st) stearic acid. However, in the presence of 0.1 M NaCl at pH 6, shear-flocculation was observed at stearic acid concentrations = 10-4 M (22.5 lb/st). Adsorption of stearic acid on silica was studied using stearic acids spin-labeled with a doxyl group. The presence of the spin-labeling group did not greatly affect the shear flocculation properties of stearic acid. Adsorption of labeled stearic acid on silica was measured as a function of surfactant concentration with electron paramagnetic resonance (EPR) spectroscopy and gas chromatography (GC). The GC results indicated that the stearic acid was predominately adsorbed on the surface at concentrations above 10-4 M. From the EPR spectra, the formation of aggregates of stearic acid was apparent at concentrations of approximately 10-5 M (22.5 lb/st). The results are discussed in terms of a possible mechanism for shear flocculation.

Jan 1, 1995

By Y. Topkaya, R. E. Johnson, D. Buttinelli, B. R. Palmer, A. Geveci, L. Stoppa, C. Lupi, F. Pochetti

Representative samples of a composite mixture of three typical Cu/Zn complex sulphide ores, namely Black-, Yellow- and Altered-ore, from the Cayeli deposit in Turkey, were used for leaching tests in 2.2 M FeCl3, or 1 M CuC12-2 M NaCl solution in the temperature range from 313 K to 363 K (40O to 90O C), with and without the presence of an organic solvent for elemental sulphur, such as CCl4. The leaching rates of copper and zinc were quite high, as expected, in FeCl3 solution and complete recovery of both metals was obtained at the highest temperature when the solvent was present. However in CuC1, solution, extraction yields of the order of 95% only for Cu and Zn were achieved and the positive effect of the solvent was not clearly shown. The kinetics curves of Cu leaching by FeCl3 indicated a model of reaction rate depending on the particle surface, as in a chemically controlled reaction, in tests with the presence of CCl4. Without the solvent, or in CuCl2 media, the model of the diffusion controlled reaction seemed to prevail. Values of apparent activation energy, in both of the leaching processes, were determined and compared with those reported in literature.

Jan 1, 1993

By C. D. Iles

The philosophy used in designing and writing Duval's Sierrita mine design programs is discussed. The Sierrita Incremental Design system (SID) is reviewed with emphasis on Pushback Extraction Design (PED). FED is a method by which predesigned pushbacks are sequenced into an optimized period-by-period design that can be directly utilized in daily operations as well as intermediate and long range planning. The advantage of SID is that it provides a practical, mineable open pit design. PED is not a theoretical design system; it is in operational use.

Jan 1, 1981

By Felicia F. Peng

Using a fuzzy logic controller, a signal applied on the processes may be generated through a linguistic protocol expressing an operator's intuitive control strategies. In this work, fuzzy logic controller and PID controller imposed upon the feedback liquid level control systems for a stirred tank are studied and compared. The construction factors including the shape of membership functions, number of fuzzy variables, number of inputs, number of rules, and different defuzzification methods are considered in design and formulating the fuzzy logic control strategies and algorithms. From the analysis of the strategies and control performances, an optimum controller may be generated by making use of the best combination of these fuzzy construction factors.

Jan 1, 1997

By B. J. Arnold

A coal's size distribution clay content and moisture content can affect its handling behavior. But the combined effects of these properties and the effects of other properties are not known. Research underway at CQ Inc.'s (formerly EPRI's) Coal Quality Development Center (CQDC) and at Iowa State University (ISU) will answer these questions as part of a four year project to develop a coal handleability index for utilities to use when specifying coals. This paper will present preliminary data from the first year of the project, which focused on obtaining data on the chemical and physical properties of carious coals and their measured handling properties. Additionally, size, ash and moisture analyses and shear test data for several coals used at one power plant will be presented along with correlations between these physical and chemical properties and the measured handling properties. These data lead to the conclusion that while moisture content is the most important variable, the amount of -44 µm (-325 mesh) coal fines is a significant factor in determining coal handling behavior.

Jan 1, 1992

By K. L. Lamb

At the Sierrita mine, 40 km (25 miles) south of Tucson, Arizona, Duval Corporation is rapidly gaining operating experience with its new Portable Crushing and Conveying System, (PCCS). As of November 23, 1983, over 4.5 million tons (5.0 million st) of ore have passed through the system. Mining cost per ton for the months of July, August and September was 83% below the average for the first five months of 1983. Although all the cost reductions experienced cannot be attributed to the Portable Crusher, it was a major contributing factor. The Sierrita ore deposit has several natural topographic and geologic conditions which are not favorable to mining. It is not a sidehill deposit and therefore no low-level exit points exist to facilitate truck haulage. The ore is very hard. Quartz diorite, hardest of the three major rock types, averages 172-207 MPa (25-30 000 psi) unconfined compressive strength and may run as high as 345 MPa (50 000 psi). Blasting in this rock produces oversize material which runs approximately 20% 51 centimeters (20 inches). The ore is low grade, averaging slightly better than .30% contained copper and .035% contained molybdenum, with small amounts of silver. These conditions, plus high design production tonnages, make the Portable Crushing and Conveying System (PCCS) practical for Sierrita. Without crushing and conveying, truck haulage would be prohibitively expensive. A typical, October, 1983, ore haul from the bottom of the pit would involve a vertical lift of 260 meters (850 ft) and a horizontal distance of 3 860 meters (12 200 ft) were not in-pit crushing and conveying available. The corresponding cycle time would be nearly 32 minutes.

Jan 1, 1984

By Victor F. Hollister

Introduction Trends of successful discovery technology and psychology emerge from a thoughtful study of various companies' exploration programs. These subjective patterns can be generalized into groups of factors for discussion. Here, for convenience, factors that influence exploration success are separated into management and geologic concerns. Most successful discoveries have a demonstrably favorable management combined with a technically competent geologic input. Both are required. But the management input is decisive. Management factors include the correct definition of management's role; cost of exploration; time needed for exploration; commodity selection; and the fostering of autonomy, creativity, and confidence in the geology department. Geologic factors include imaginative technical competence (field as well as academic), correct development and use of empirical exploration or prospecting models, and dedication. Success comes to those entities that are properly managed and have technological competence. A management team that directs a company's business has been compared to a dynasty. The dynasty lays out policy and follows up with appropriate action. In that management's power is pervasive, the term is appropriate. Management's role is, however, more important. Many examples can be cited where the geologic input was impeccable. But management somehow snatched defeat from the jaws of victory, and the exploration success was turned to a third party's profit. Management Factors Management's role can be broadly generalized to four parts. These are to identify the commodities it seeks, define its part in the exploration process, develop a functioning exploration department, and have the desire to succeed. It must have confidence in its geologists and delegate to them the authority and responsibility they need to operate successfully. Head office management cannot do the thinking for a field staff thousands of kilometers away. There is no substitute for confidence and delegation of authority. Successes came to those who had the freedom to act. Motivation is a management requisite. Management's role is to prevent destructive, internecine political battles within the corporate structure. Most large US mining corporations have well known histories of political strife that have damaged their exploration efforts. Management's role must, above all, include the desire to succeed. There are cases where management has been confronted with a commercial exploration success, but their reaction is to request additional study or exploration. Perhaps the problem of bringing a commercial find into production is beyond their capabilities. But a bona fide discovery sent back for additional work commonly is lost due to that management. The cost of exploration is a factor that management must accept. A variety of studies made during the past 40 years shows the cost per discovery to be $25 million, $38 million, $200 million, or even $290 million. These figures are derived by dividing the total exploration expenditure by the number of discoveries. However, successful management dynasties have a much lower cost per discovery during their management regime. Asarco, from 1948 through 1963, had one of the lowest cost discovery rates in the world. Duval Corp., from 1948 through 1968, had comparably low discovery costs. Placer Development, from 1955, was equally successful. Western Mining in Australia has had one of the longest lived dynasties associated with exploration success. Time is vital in exploration success. Most successful exploration case histories stress sufficient time in project exploration so that the target is well tested. A large target cannot always be adequately evaluated by a few holes (strat or concept testing). Serendipity helps in exploring large targets, but it best operates in a lengthy program. Numerous case histories include pleasant surprises. But these came mostly after the 10th hole. Commodity markets are important factors governing exploration success. Management's decision to explore for a specific commodity can doom its effort if that product suffers from severe oversupply. Unquestionably, progressive copper price increases from 1948 through 1968 helped convert marginal porphyry copper discoveries

Jan 8, 1985

By A. M. Johnson, D. H. Carlson, D. L. Johnson, S. T. Bagley

A biologically assisted ferric iron leaching system was evaluated for in situ recovery of three copper sulfide oresfrorm northern Michigan. Laboratory scale bacterially assisted ferric sulfate leaching tests were run on the three ores. A T. ferrooxidans strain was found that could be adapted to copper in solutions at concentrations as high as 20 g/L. Column leaching of 4.5 to 2 mm (-4 +I0 mesh) material yielded extractions of 80-90% copper from one ore and 70 and 60% from the other ores. The highest copper extractions were from the Mount Bohemia ore deposits located in the Keweenaw Peninsula, which have fracture controlled chalcocite mineralization. The Bohemia ores are apparently well-suited for in situ solution mining.

Jan 1, 1987

By Z. T. Bieniawsk, C. A. F. F. Santos

The effects of artificial weathering on the mechanical properties of the Loyalhanna sandstone have been investigated. Weathering was simulated in the laboratory by subjecting cylin- drical specimens of rock to alternate cycles of wetting and drying (in distilled water at 2O0C 2 5OC and in an electric oven at 105OC t 1°C, respectively). The total number of cycles was 100 and the geomechanical characteristics of the altered material were determined through uniaxial compressive and indirect tensile ("Brazilian") tests, with the determination of axial and trans- verse strains and monitoring of acoustic emission activity (rate and total event count). Moisture content and weight loss data were collected after each cycle and the mechanical parameters (unconfined strength, indirect tensile strength, young's modulus, Poisson's ratio, permanent set and AE/MS activity) were determined for unweathered specimens and after 10, 20, 50 and 100 cycles of wetting and drying. Hypotheses for the effect of weathering on the geomechanical properties of the Loyalhanna sandstone are proposed as reinforced by petrographic analyses carried out for the different stages of artificial weathering. A methodology for assessing the degree of physical weathering of rocks is proposed based on the number of wetting and drying cycles.

Jan 1, 1986

By G. Myers, C. J. Wendt, W. H. Wilkinson, M. D. Dennis

Precious metal mineralization at Mt. Hamilton, NV is associated with a polymetallic, garnet-pyroxene skarn system developed in middle to upper Cambrian calcareous shale, limestone, and dolomite. The skarn is developed around the Cretaceous Seligman and Monte Cristo calc-alkaline stocks. Gold is associated with intense retrograde alteration. Later epithermal quartz veins contain gold, silver, base-metal sulfides, and sulfosalts cross-cut skarn alteration. Westmont Mining Inc. is currently developing two mineralized zones containing a geologic resource of about 7 Mt (7.7 million st) that averages 1.7 g/t (0.05 oz per st) gold and 17.2 g/t (0.5 oz per st) silver. The project will have an estimated mine life of seven years, with a planned annual production rate of I t (35,000 oz) of gold and 9.3 t (300,000 oz) of silver.

Jan 1, 1990

Gaby Copper Mining?s Gabriela Mistral property is located in the Antofagasta region of northern Chile, at an altitude of 2,660 m (8,727 ft) above sea level. The reserve contains an estimated 562 Mt (620 million st) of oxide ore with an average grade of 0.41 percent total copper. The mine went into production in 2008. Gaby Copper faced the problem of having no reliable way to measure the solids level. This is a challenge that exists throughout the mining industry, where dust in the air and accumulation of solids on a sensor make accurate measurements difficult in areas such as transfer chutes, the rock box underneath crushers, silos and anywhere else that information is needed on the level of solids. The next-generation technology in the Sitrans LR560 radar from Siemens addresses this challenge. With a frequency of 78 GHz ? higher than previous generations of radar ? it provides a more robust signal for measuring in areas where there are high levels of dust accumulation. The Sitrans LR560 provides a signal beam angle of four degrees, significantly narrower than any other product on the market can offer.

Jan 1, 2014

By C. E. Roessler

Uranium and its decay series are associated with phosphate deposits of marine origin. Uranium concentrations are on the order of 100 to 200 ppm in matrix from the Bone Valley formation of Central Florida and about 25% this value in matrix mined from the Hawthorne formation in North Florida. Occupational radiation exposure due to this source has been under study in Florida since the mid 1970's (Windham, Partridge, Horton 1976; Roessler and Prince 1978). This report is based on findings of an industry-wide scoping survey conducted by the University of Florida during March 1976 through May 1977 and subsequent studies in selected individual facilities. PHOSPHATE MINING OPERATIONS Mining and beneficiation operations are diagramed in Figure 1. At the excavation site, electric powered draglines remove the overburden and expose the phosphate matrix (ore) which is then slurried and pumped to the beneficiation site. At the washer stage of the beneficiation plant, the matrix is subjected to washing and screening. A coarse product, "pebble" is produced and sent to storage piles while the fine fraction is passed through a series of cyclones to remove the clays. The generated clay suspension is sent to settling ponds while the remaining sand-sized fraction is sent to the flotation plant. At the flotation plant, phosphate particles are recovered from the fine sand particles of similar size through several stages of treatment with reagents, agitation and separation of floating and sinking fractions. The high grade concentrate produced is transferred to storage while the sand tailings are discarded. [ ]

Jan 1, 1981

By J. A. Brierley, C. L. Brierley, K. A. Prisbrey, R. W. Bartlett, J. G. Harrington

Bacterial oxidation of gold-encapsulating sulfide minerals in low-grade refractory ores was investigated over a period of one year. Crushed ore samples were held in wet, bacteria-inoculated, aerated columns. Sulfide mineral oxidation data were correlated with subsequent gold cyanide extractabilities. Experimental results for both sulfide conversion and gold extraction were compared with a biooxidation kinetics model that incorporates rock size, mineral grain size, and heterogeneous pyrite reaction kinetics. Using the model, extrapolations were made over three years for biooxidation of ore in large stockpiles. Ferric ion (oxidant) diffusion in the solution-filled pores of the rock matrix does not control the biooxidation kinetics of ore crushed to -25 mm.

Jan 1, 1993

By Chen Ziming, A. Burkert, A. L. Mular

A mechanism has been proposed for autogenous grinding that involves three distinct types of breakage: self impact breakage, media breakage and abrasion. Based on this analysis a mathematical model and an autogenous grinding simulator have been developed. Using pilot plant data fitted to the model, the simulator was tested and employed to examine both the scale-up problem and the effect of feed size distribution on performance.

Jan 1, 1995

By Robert L. Gamble

The world's largest fluidized bed steam generator located at Rivesville, West Virginia is currently undergoing initial operation. This unit is designed to generate 3708 kg/s (300,000 Ib/hr) equivalent to 30 MWe of superheated steam while firing coal in a fluidized bed of limestone. Coal was first fired in this unit in December, 1976 and start up operation is progressing.

Jan 1, 1977

By Ben V. Petersen

Surveying is to tunneling, as a steering wheel is to a car—somewhat essential if you want to end up in the right place. The principles of tunnel surveying have remained unchanged since the first tunnels were constructed: To mathematically connect the selected start and end points of a tunnel and physically translate that alignment onto the ground. The alternative is just dead-reckoning and leaves the probably less than satisfying end results to chance. Today’s laser-guided tunnels often have to thread the needle through a maze of soil types, utilities, structural features and other underground considerations. Surveying makes it possible.

Jan 1, 2005

By J. David Lowell

The first part of this article is a review of industry techniques and styles during the past 50 years. It is followed by my career history during the same period. The second part covers my ideas about what works in mineral exploration. These include estimates about discovery costs, thoughts about education of explorationists, organization of exploration groups and my opinions about the relative value of exploration techniques. Evolution of exploration techniques [Table 1] shows the evolution of mineral exploration techniques and styles from 1950 to 2000. During the first half of that period, there was a progressive increase in exploration drilling. During the second half, there was a decrease in prospecting and an increase in high technology, indirect exploration and a rapid increase in discovery cost.

Jan 1, 2000

By Allan E. Koski

Michigan is the second largest iron ore producing state in the United States. The Empire Mine, celebrating its 30th anniversary in 1994, is the largest iron ore mine in the state. The Empire Iron Mining Partnership is an iron ore mining, concentrating and pelletizing facility managed by The Cleveland-Cliffs Iron Co., a subsidiary of Cleveland-Cliffs Inc. The Empire Mine is located near Palmer, MI on the Marquette Iron Range in Michigan's Upper Peninsula. The partnership includes Inland Steel Co., LTV Steel Co., Wheeling-Pittsburgh Steel Corp. and Cleveland-Cliffs. Mine construction began in 1960. The first pellets were produced in late 1963. Successive expansions in 1967, 1974 and 1979 resulted in Empire reaching a present annual capacity of 8.1 Mt (8 million long tons) of pellets. In late 1993, a milestone was reached with the production of Empire's 152-Mt (150-millionth long ton) of iron ore pellets.

Jan 1, 1994