Search Documents

By R. L. McNearny, K. A. Barker

Four numerical models written with the "PFC2D " program were compared against four similar physical models. The numerical models were constrained numerically to closely follow the caving behavior of the physical models. Results from the numerical analyses closely simulated both the granular and blocky behaviors of the physical models, including bridging and interlocking of the simulated orebody during draw. The drawdown patterns and the rate of draw developed during numerical modeling also closely simulated the physical models. The same assumptions and governing parameters used in analyzing the first four models were applied to an additional model. The fifth model employed a completely different, uneven, draw sequence than the other four models, allowing the material to flow in a more granular manner with a demonstrated instability of the undercut sections between each drawpoint opening. Drawdown patterns and behavior of the numerical material of the first four models progressed at uneven and inconsistent rates, similar to those seen in the physical models. By inspection, the overall shape and flow lines of both the numerical and physical models were close in the area removed and in the flow characteristics. The fifth model proved to be the most unstable of all the models tested, with poor correlation to the physical models. The uneven draw sequence, coupled with an additional frictionless wall condition and an added drawpoint, caused the material to flow in a very granular manner. Information generated by this study can be used as a first approach in determining the proper draw rate, drawpoint spacing and undercut thickness for a block-caving operation. Numerical models are often difficult to predict and interpret. However, this study should increase the confidence level for use of the PFC2D program in the future.

Jan 1, 2000

A Mineração da Trindade (Samitri) is a major Brazilian iron ore producer. Founded in 1939, privately owned Samitri operates six mines with a total production capacity of 14.5 Mt/a (16 million stpy). The mines are located in southeastern Brazil in the state of Minas Gerais. They are operating in the iron ore quadrangle, Brazil's primary iron ore-producing region. In addition to iron ore production, Samitri has the capability to produce 350 kt/a (386,000 stpy) of ferruginous manganese ore from two mines, also located in the iron ore quadrangle. Historically, about 70% of Samitri's production of lump ore, sinter feed and pellet feed is exported. Destinations include Belgium, Luxembourg, France, Germany, Trinidad and Tobago, China, Turkey and the United States. Alegria Mine In September 1989, Samitri started a new processing plant to treat itabirite, a low-grade iron ore. The goal of the plant was to produce sinter feed (coarse fraction) and pellet feed (fine fraction). Primary separation of sinter feed from pellet feed was accomplished with conventional vibrating screens making a 0.4-mm (40-mesh) cut. The screen oversize was stockpiled as sinter feed. The undersize was deslimed with hydrocyclones and upgraded by conventional froth flotation. Resulting pellet feed grades ranged from 3% to 3.5% Si02. A change in pellet feed requirements by Samarco Mineração SA, a Samitri subsidiary, called for Si02 levels below 1 % and increased production levels. Moreover, market demands called for a change in sinter feed size distributions. Unfortunately, lower pellet feed Si02 levels could not be achieved with the existing process. This was because of the presence of 35% +0.15 mm (+100 mesh) in flotation feed. Flowsheet development. Laboratory and pilot-plant studies conducted at Samitri's research facility found that to achieve lower Si02 levels, the +0.15 mm (+100 mesh) in flotation feed must be kept below 5% to 10%.

Jan 1, 1997

By David E. Nicholas

Design of underground openings is becoming more critical as the mine deposits become lower in grade, initial investments increase, ore depth increases, additional safety regulations come into law, and increased ore recovery is required for conservation of minerals. Stability of these openings is dependent on the strength of the rock mass and the pre-mine stress field. The rock mass is composed of solid blocks of rock (rock sub- stance) and structural features (faults, joints, bedding, etc.). Methods of testing the rock mass strength are improving and be- coming more common, however it is difficult to justify the high cost of large scale testing for an initial mine design. An alternative to testing the rock mass is to measure the rock substance and the structural features separately, and then combine them to estimate the rock mass strength. The rock mass strength will vary depending on the orientation of the opening with respect to the structural features. The other factor affecting the stability of underground open- ings is the pre-mine stress field. Methods are available to measure "directly" the pre-mine stress in competent and relatively massive rock. These methods are costly to employ, therefore, they may not be justified in an initial study. The pre-mine stress field can be estimated based on the structural relationships formed from past tectonic events.

Jan 1, 1976

By Jon Y. Kaneshiro, Sean A. Menge, M. Luis Piek, Brian Barker

The Lake Hodges to Olivenhain Pipeline project is part of a 40-megawatt pumped storage project linking two reservoirs as part of the San Diego County Water Authority’s $939 million Emergency Storage Project. Seeking to expedite project completion, the project was advertised as Design-Build, a first for the owner. Awarded to Kiewit Pacific with Parsons as designer, the 1,750m (5,700ft) long, 4.25-m (14 ft) horseshoe tunnel was excavated with conventional drill-and-shoot technique. The mining method was well suited to deal with the shear zones, the very abrasive rock, and 13.3% and19.6% grades. At the apex of the alignment, a 60m (200ft) by 3.6m (12ft) diameter raisebore shaft with surge chamber to protect against pump malfunction was constructed. Upon completion of mining, the tunnel was lined with a 3m (10 ft) diameter high strength steel pipe. Scheduled to come on-line by January 1, 2008, the Lake Hodges to Olivenhain pumped storage project is valued at $108 million, delivering a reliable source of water in emergency situations and electricity-generating capability to meet the growing demands of the San Diego region.

Jan 1, 2007

By W. N. McAnulty

Because so many interrelated technical, economic, legal and political factors are involved in evaluation of commercial mineral deposits, it is common practice today to assign such work to a team of specialists including geologists, mining engineers, metallurgists, lawyers, and economic evaluation experts. Each member of the team plays an important role; the role of the geologist is particularly important. The geologist involved with evaluation of fluorspar deposits needs all the geologic and economic training and experience required for evaluation of metallic mineral deposits. Few, if any, industrial or metallic minerals occur in so many geologic environments as fluorite. Fluorspar, and aggregate of rock and mineral matter containing enough fluorite to make a commercial deposit (ore), is somewhat more limited in its modes of occurrence than fluorite, but it too is found in a variety of environments.

Jan 1, 1970

By Wendell H. Wiser

A comparison is presented of coal pyrolysis at temp¬eratures ranging from 4090 to 497°C and thermal dissolution of coal in tetralin at temperatures ranging from 350° to 450,°C, both utilizing a Utah high-volatile bituminous coal. The initial coal pyrolysis reactions are second order with an enthalpy of activation of 35.6 kcal per mole. The fraction of total product yield produced under second order conditions ranges from 67% at 409°C to 96% at 497°C. The process then gradually deteriorates to a first order reaction in the later stages with enthalpy of activation of 4.1 kcal, per mole. The initial reactions of solution of coal in tetralin are second order with an enthalpy of activation of 28.8 kcal per mole. The fraction of total product produced under second order conditions ranges from 63% at 350°C' to 94% at 450°C. The dissolution process then gradually changes to first order in the later stages with enthalpy of activation of 15.6 kcal per mole. A model is presented which relates the two processes and explains, the significance of the above similarities.

Jan 1, 1967

By Yehia M. Eyssa

A "straight wire" flow through magnetic ore separator has been designed, built and successfully used to separate magnetite from typical slurries. The purpose of these experiments was to simulate the high field profile of a "straight wire" superconducting magnetic separator which would be capable of separating weakly magnetic hematite ore from typical slurries. Magnetite was used as the test mineral because it experinces the same magnetic forces at low field as does hematite at high field. The present separator concept is based on the fact that there is a particle concentration profile due to the gravity field for low velocity turbulent flow. When a magnetic field force of -g is applied the concentration profile of the magnetic particles will be reversed leaving the nonmagnetic particles flowing alone at the bottom of the channel. By means of a divider at the end of the channel the concentrate is separated from the tailings. It is shown that the time needed to deflect hematite particles in a narrow cylindrical channel concentric with the superconducting wire is small enough so that high throughputs in the turbulent flow region are possible. In the case of a high field superconducting separator the centrifugal force could replace gravity by rotating the flow around the straight wire conductor.

Jan 1, 1974

By J. H. Kempton

Refinement of environmental procedures can produce significant cost savings at most mines. Grouting permeable aquifers reduces water pumping and disposal costs. Stable groundwater quality supports reduced groundwater monitoring; and for contaminated groundwater, in-situ or natural restoration should be evaluated. Waste-rock characterization can be minimized using fewer (but more representative) samples, inexpensive surrogate analyses (e.g., NAG instead of humidity cells), and appropriate tests (e.g., avoid meteoric tests on sulfide). Selective waste-rock handling should be compared to random emplacement, which is often cheaper and more stable. Finally, incorporating schedule uncertainty in modeling allows the flexibility to revise mine plans within permits.

Jan 1, 2000

By Satid Therdkiattikul, Donald A. Dahlstrom

By oxidizing the pyrite matrix through biological leaching of precious metals ores or concentrates, better than 90% recovery of gold and silver is achieved. The paper develops three precipitation processes that eliminates arsenic and all other toxic elements in the resulting liquor after the biological reactors. In addition, the precipitates are highly crystalline and resist resolubilization. The latter must be tested for at least six months by EPA test procedures. The three systems are temperature (must be at least 120°C or higher) lime or limestone. A continuous pilot plant was employed for all three systems and complete recommendations are given to optimize Fe/As molar ratio, reaction kinetics (detention time) pH, temperature, wt % feed solids as well as resultant reagent consumption based upon continuous operation.

Jan 1, 1995

By C. Maltesh, P. Somasundaran

The ever increasing need for treating fine complex mineral bodies has led to the evolution and rapid development of advanced processing techniques for fine grinding, classification an if mineral separation and purification. With the introduction of these new technologies and understanding of underlying fundamental principles, mineral processing is now being applied to materials ranging from ceramics and composites to superconductors. In this review, current and potential applications of mineral engineering techniques to advanced materials processing are discussed. Particularly, material processing involving ultrafine grinding, dispersion and flocculation and thin film formation is examined. Novel techniques of solid/liquid separation involving manipulation of interfaces and use of high intensity high gradient superconductor magnetic equipment for solid/solid separation are discussed.

Jan 1, 1990

By Williams R. Reynolds

Studies of the northeastern Mississippi bauxites were initiated primarily for the purpose of ascertaining the quality and quantity of the ore. Subsequently, this ore was found to have a rather dubious economic value as was previously suspected but never established in earlier economic reports (1, 2, 3). However, the quality of ore was found to be higher than previously thought. Even though the ore bodies were determined during the early stages of this study to be too thin, small and widespread for commercial production a continuation of the study was not abandoned. On the contrary, the present investigation was intensified concentrating less on the economic application and more on stratigraphy and genesis. Considering the ever increasing demand for aluminum products the northeastern Mississippi bauxite district which includes portions of Tippah, Benton, Pontotoc, and Union Counties may soon become, in spite of inferior quantities of ore, an attractive area for bauxite production. Presently, however, the meager quantity of ore discourages exploitation. On the other hand, these northeastern district bauxites are facies of more extensive units of lignite bearing high aluminum clays, and considering the advances in aluminum extraction from clay these clays may in the future beckon mining interest. The bauxite of the northeastern Mississippi district, mapped as a part of the Betheden Formation (4). has an outcrop trend along the county lines of Tippah and Benton Counties and the extreme western portion of Union and Pontotoc Counties. Studies of exposures and cores stratigraphically positions the outcrop between the middle Midway Porters Creek Clay and the lower Eocene Wilcox sands and

Jan 1, 1977

By R. D. Williams

Several hydrometallurgical leach processes have been recently proposed for the recovery of copper from copper concentrates. These include the Cymet Process of Cypress Metallurgical Processes Corporation, the Arbiter Process of the Anaconda Company, and the Treadwell Process of Treadwell Engineering company(1). These processes and similar processes for recovery of other minerals, have several phenomenological similarities which make their quantitative description difficult at best. These include (a) the presence of more than one phase, (b) non-uniform mineralization of the feed concentrate, (c) surface and diffusional effects, and (d) a particle size distribution which varies with time. Semi-theoretical, rather than purely empirical, treatment of such processes in their developmental stages will result in a better understanding of the physico-chemical mechanisms in effect. This, in turn, will allow reliable process designs to be made on reasonable time scales for reasonable development costs. Once a production unit is built, such an approach will provide straightforward methods for process control and optimization. A research and development effort to determine criteria and procedures for semi- theoretically characterizing such mineral leach recovery processes has been initiated in a joint venture by the Arizona Bureau of Mines and the College of Mines at the University of Arizona. This group has as its task the mathematical characterization of hydrometallurgical leach recovery processes using semi- theoretical mechanisms for the underlying phenomena. The resulting models are experimentally verified and parameterized on the laboratory scale in such a way that they can be utilized with similarity criteria to provide reliable scaleup to production designs. This discussion will be centered around the elements of such an approach and how they fit together.

Jan 1, 1975

By Stephen G. Hardcastle, Michel G. Grenier, Kevin C. Butler

Today there are numerous electronic rotating vane and thermal (hot-wire) anemometers, as well as vortex meters available to measure air velocity. Of these, a laboratory and field evaluation has found that certain instruments are better suited to routine airflow measurements in mine roadways and ventilation ducts. This paper concludes a study sponsored by the Atomic Energy Control Board of Canada, that was introduced at the 5th U.S. Symposium. The study investigated the suitability of currently available electronic anemometers as replacements for the traditional mechanical analog devices while maintaining standard methods such as the continuous traverse. Six electronic instruments were subjected to extensive tests under controlled conditions both in a wind-tunnel and in the field at an underground mine. The evaluation concluded that ergonomics and design were major considerations in unit preference as most of the instruments had very similar performance characteristics. Specific findings were: a) In the wind-tunnel the vane anemometers, especially the "micro" vanes, were more susceptible to misalignment or yaw effects but these were not noticeable in the field; b) Both the vortex and hot-wire anemometers were suitable for continuous traverses of mine roadways; c) Traversing ventilation ducts was more practical than a Pitot-tube multi-point assessments or discharge measurements; d) Yaw is a major concern in duct measurements; e) The continuous traversing method for roadways overestimates the average air velocity; f) Hot-wire anemometers can require significant air density corrections; and g) Hot-wire anemometers are better suited than rotating vanes to mine roadways of less than 1 m/s average air velocity. Based on research detailed in this paper, the ventilation engineer should be able to match the mine's requirements with the presented instrument performance characteristics, thereby optimizing the purchase of a new anemometer and the efficiency with which air velocities are measured.

Jan 1, 1993

By W. S. Weldon, R. M. G. Machunter

The use of spiral separators for the beneficiation of fine coal typically in the size range - 2+0.lmm is now well established process technology. Developments during the mid 1980's resulted in the production of cost effective, efficient large diameter coal spiral separators. Recent developments and research have been geared to optimise metallurgical performance, materials handling and equipment geometry of large diameter coal spiral separators.

Feb 24, 1997

By Romeo Jurani, Ralph Dresel, Fred Kissell, Charles Parker

This report describes actions taken to control silica dust at the Yucca Mountain Exploratory Studies Facility (ESF), a tunnel located in Southern Nevada that is part of a scientific program to determine site suitability for a potential nuclear waste repository. The rock is a volcanic tuff containing significant percentages of both quartz and cristobalite. Water use for dust control was limited because of scientific test requirements. A major dust reduction was achieved with an intermediate air cleaning station located on a rear deck of the TBM trailing gear.

Jan 1, 1999

By Hiroshi Soda, Atsumi Ohno, Hiroyuki Yamazaki, Alexander McLean

INTRODUCTION The method of heat removal during a casting process strongly influences the crystal morphology of the cast product and hence the metallurgical and mechanical properties of the solidified materials. In this paper, the Ohno Continuous Casting Process (OCC) is described in terms of the casting conditions and the type of structure observed in the cast product. Significant improvements are observed in workability, fatigue strength and corrosion resistance of castings produced by the OCC method, Ohno (1988). Applications of this technique to low melting point nonferrous metals and alloys are discussed. The feasibility of the application of this technology to high melting point materials is outlined. THE OCC PROCESS The OCC process involves delivering liquid metal into a heated mold, the temperature of which is held just above the solidification temperature of the metal to be cast. This is the key point which differentiates the OCC process from the conventional continuous casting method. A schematic illustration of the OCC process is shown in Figure 1. The Formation of a Single Crystal When the mold is heated above the solidification temperature of the metal to be cast, nucleation on the mold surface is prevented and solidification takes place only at the mold exit. The heat is extracted through the product being cast by a cooling device located near the mold outlet. Crystals are formed only at the tip of the dummy bar at the start of casting, and as the dummy bar travels away with a progressively increasing speed from the mold, the position of the solid liquid interface will align with the mold exit, producing a unidirectionally

Jan 1, 1990

By Alan Zeni

Blind shaft drilling equipment has not changed substantially since the 1970s. Since it resides in a niche market between conventional shaft sinking and raise boring, the relatively small demand has resulted in some stagnation of development. In the 1990s the technology found a larger foothold in foundation and deep piling work for civil construction. WIRTH GmbH from Erkelenz, Germany has been servicing this market for many years with pile top drilling rigs and tools. Frontier-Kemper Constructors, Inc. recently entered into an agreement with WIRTH to develop a new generation of large diameter blind drilling equipment more specifically aimed at mining needs. The, recently completed, DHI-240 is the first rig to apply the most recent technology. This machine made its commercial debut in the fall of 2008. A description of the technology and a short case study of the first project will be described

By Xinyang Xu, Jirun Xu, Changlie Deng, Kang Yan, Luo Qian

Cake filtration is a complex process and the cake constructure is very difficult to describe in theory. Cake constructure parameters, such as the cake prosity, pore size shape and even its distribution, are main factors influencing the filtration results but have not been thoroughly understood yet. In this paper the fractal theory, an effective mathematical method in describing the self-similar phenomenon is used to investigate the filter cake constructure, and the scanning electron microscope and automatic image analyzer are used to measure the cake constructure. Cakes which formed in different condition are examined and the fractal dimension of the cake are calculated. The study shows that the constructure of the filter cake can be approximated by Sierpinski fractal geometry and that the fractal dimension of filter cake, related to the particle characteristics, slurry concentration and filtration pressure is a good parameter to describe the pore size distribution and the cake penetrability.

Jan 1, 1995

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

8.1 INTRODUCTION Under room and pillar mining if the extraction ratio is low, (i.e., < 50%) a pillar can support the overburden without collapse and there will be no surface subsidence whatsoever. In other words, if the pillar sizes are properly determined to support the overburden weight, the roof strata cannot cave and there will be no surface subsidence, provided the entry width is small and properly reinforced so that a continuous roof fall leading to piping or the total collapse of the roof does not occur. Under the prevailing mining conditions in the US if only development mining is em¬ployed in room and pillar mining (i.e., no pillar extraction), the extraction ratio is usually less than 50% and generally no surface subsidence will occur. If pillar mining is employed, surface subsidence may occur, depending on the extraction ratio and the size of the remnant pillars (or stumps) left in the gob. The higher the extraction ratio, the smaller the stump pillars left behind in the gob. As the size of the stump pillars becomes smaller, the possibility of their support¬ing the roof without collapse is smaller. If all stumps are crushed completely, the roof will collapse and surface subsidence will occur. Again, whether surface subsidence occurs, it depends on whether the remaining stumps can support the overburden or not. Therefore, since the weight of the overburden which the stump pillars have to support is proportional to the mining depth, a fixed¬size stump pillar can support the overburden at a shallow depth, but will collapse under greater depths. In this context extraction ratio is not the only parameter for determining whether surface subsidence will occur. Furthermore, during pillar mining a pillar can be cut away in many ways to finally reach the same extraction ratio. Therefore, the safest way to determine whether or not sur¬face subsidence will occur in room and pillar mining is to compare the strength of all stump pillars in the panel of interest with the weight of the overburden that the pillars have to support. If they are too small to support the overburden, surface subsidence will occur. Under normal mining practices the characteristics of surface subsidence profiles vary with methods of mining. In the US there are two types of coal mining methods, i.e., longwall and room and pillar mining. Longwall mining is indisputably a total extraction method, but different percentages of coal recovery are achieved in room and pillar mining. Recovery is much higher for sections with pillar extraction than those without pillar extraction. For those without pillar extraction, coal recovery increases with increasing entry width or decreasing pillar size. For those with pillar extrac¬tion, the total coal recovery depends on the amount of coal ex¬tracted from each pillar which is in turn dependent on the roof conditions and methods of pillar extraction. Bauer and Hunt (1981) analyzed the characteristics of the subsidence profiles due to the three types of mining methods in Illinois. Fig. 8.1 shows the range of locations associated with the following profile features: profile edge, maximum tensile curvature, maximum slope, maxi¬mum compressive curvature, and maximum subsidence. The scat¬ter of the data increases with decreasing percentages of extraction. The profile is much sharper for longwall mining and becomes milder as percentage of extraction decreases; for longwall mining the profile edge is always beyond the opening, while in room and pillar mining it may fall within. The location of maximum tensile strain moves outward, while that of the maximum compressive strain moves inward as the percentage of extraction decreases and the maximum subsidence decreases with decreasing extraction ra¬tio. The general concepts discussed in this chapter may not apply to the entry development sections between two longwall panels where roof caving in both panels are very severe and overlap each other. Consequently, it must be treated differently. 8.2 CASE STUDIES Kohli et al. (1982) described several case studies on surface subsidence due to room and pillar mining with pillar extraction. In one case, the seam was 6 ft thick and ranged from 650 to 800 ft deep. The panel was 720 ft wide (Fig. 8.2) and was developed with seven entries. Each entry was 18 ft wide and the pillars were driven at 88 ft center-to-center between entries and crosscuts. Dur¬ing retreating, two additional pillars (pillars J and K) were devel¬oped, two blocks ahead of the pillar line, to take the barrier pillar, 160 ft wide, between panel No. I and No. 2. Pillar extraction began by taking a central slice across the whole panel, beginning from pillar 0 through J. After that, each pillar was sliced by 6 wing-slices, 3 on each side, leaving 4 stumps, 2 on each side. One of each pair was triangular shaped approximately 6 ft wide by 26 ft long. The other was trapezoidal, 26 ft long by 16 ft and 10 ft wide at the upper and lower bases, respectively. This resulted in a total extraction ratio of 85% within the panel. Obviously the stump pillars were not large enough to support the overburden and col¬lapsed completely. The final subsidence profiles were rather smooth, just like those under total extraction (Fig. 8.3). The max¬imum subsidence on Lines A and B was about 3 ft for an average mining height of 6 ft, but the locations of the maximum subsidence were skewed toward panel No. 1. Along Line D, the central por¬tion was flat-bottomed, but the maximum subsidence was only 2 ft, mainly because Line D was only two blocks from the right-side edge. Notice in every profile there was heaving of as much as 0.3 ft, beyond the edges above the solid coal. In another case (Fig. 8.4), the seam was 6 ft thick under 650 to 850 ft cover. Three panels, 710, 400, and 350 ft wide, respec¬tively, were extracted side by side. The entries were 18 ft wide and the pillars at 88 ft center-to-center between entries and crosscuts. Pillar extraction was practiced the same way as described previ¬ously. According to the mine maps, there was no barrier pillar left between the adjacent panels. Thus after extraction the three panels formed a common gob of more than 1460 ft wide. This was re¬flected in the development of the subsidence profile along the county road. After Panel No. I was mined, the maximum subsi¬dence of 1.2 ft occurred at Monument No. 1. This was increased to 1.6 ft after the extraction of Panel No. 2 and went to a further 1.8 ft after the extraction of Panel No. 3. The final maximum subsidence of 4.3 ft occurred at Monuments No. 6 through No. 8, while the remaining portion of the county road showed rebound. However it must be noted that the subsidence profiles were rather bumpy and fluctuated, perhaps an indication of the irregular stump pillars that were left and crushed at various time after mining. Moebs (1982) surveyed the subsidence profiles of four room

Jan 1, 1992

By Steve Kral

In 2002, many in the mining industry — companies, academia and government — realized that the industry would soon be facing a serious shortfall in salaried and hourly employees. Depending on whose numbers are to be believed, 20 percent to 50 percent of current mining professionals are expected to retire within five to 10 years. And there are not enough students currently enrolled in mineral-related programs to the fill the need. Part of the impending shortage in professionals was brought on by the industry’s negative image, which discouraged students from enrolling in mining engineering programs. Another part was that the industry was in the doldrums and was seen by the public as a dying industry.

Jan 1, 2006