Search Documents

By W. M. Luff

Introduction The Brunswick No. 12 mine is located about 27 km (17 miles) southwest of Bathurst, New Brunswick. The deposit is a stratiform massive sulfide deposit occurring in a series of sedimentary and volcanic rocks of the Tetagouche Group. These rocks are generally considered to be Ordovician in age. Ore reserves at Brunswick No. 12 are 104 Mt (115 million st) grading 3.72% lead (Pb), 9.01% zinc (Zn), 0.32% copper (Cu), and 97.9 g/t (2.8 oz per st) silver (Ag). Production in 1984 was 3.5 Mt (4 million st) at 3.57% Pb, 8.91% Zn, 0.32% Cu, and 100 g/t (2.9 oz per st) Ag. Total payable silver production that year was 211 t (6.8 million oz). This made Brunswick one of the largest silver producers in Canada. Bathurst-Newcastle area and Brunswick Mining Interest in the Bathurst area was aroused in 1897 when W. Hussey discovered an iron formation at Austin Brook, just south of Brunswick No. 6 deposit. This area, and the current No. 6 area, was explored from 1897 to 1907. Iron ore was mined at Austin Brook from 1907 to 1913 and from 1942 to 1943. Any occurrence of sulfides was overlooked until 1952. In 1952, M. J. Boylen Enterprises investigated the small sulfide body associated with the Austin Brook iron formation. Other electromagnetic anomalies associated with the iron formation were investigated. The No. 6 deposit was found late in 1952, when hole B12 intersected 97.5 m (320 ft) of massive sulfides. The No. 12 deposit, 10 km (6 miles) to the north, was found in 1953. More than 30 massive sulfide deposits have since been identified in the Bathrust area. In the 1950s, St. Joe Lead Co. did extensive test work on the No. 6 and No. 12 deposits, including shafts at No. 12, lateral development at No. 12, and testing at both deposits.

Jan 10, 1986

By P. D. Chamberlain, R. M. Nadkarni, D. J. Kinneberg

Introduction The relationship between precious metal miners and gold refiners has been uneasy over the years. Reasons for this uneasiness and lack of trust include technical factors, economics of scale, and cultural differences. Technical factors take two forms. First, concentrates, precipitates, and sponge produced at the mine site are notoriously difficult to sample. A nonrepresentative sample can be the cause of misunderstanding and distrust. Dote, however, is relatively homogeneous and can be correctly sampled and analyzed with greater reliability. Second, the technology and chemistry of fine gold and silver production is complex and quite different from dote production. Most mining companies are content not to be involved with additional processing steps. From the standpoint of process economies, it is easy to see why miners and refiners are separate groups. Mine location is dictated by the natural occurrence of ore bodies. Heavy capital investment requirements for infrastructure in remote locations usually limits companies to produce the first marketable product from a mine. Beyond that point, the economies of scale and large capital investments for refineries generally dictate that the outputs of several mines be combined to feed a single refinery. The refin¬ing process is so complex that refineries are generally built in larger cities with a skilled labor pool. Therefore, only the largest mines can afford to refine their own output. Lastly, there are cultural differences between the miner and the refiner. The miner, particularly the small gold miner, is by definition a risk taker in a risky business. Refineries, on the other hand, have historically been operated under legal or implied monopolies approved by the government. The government is interested in owning gold, either for currency reasons or because many national mints are major users of gold coins. It is not surprising, then, to find that miners may regard refiners as part of an unresponsive government bureaucracy or, worse, as "city slickers." It is easy for the two groups to distrust each other with these different backgrounds. The interface between miner and refiner does exist and affects nearly all precious metal mining companies and most refineries. This paper discusses the technical and economic aspects of the interface. It points out how both parties can improve the relationship. Technical interface Precious metals selectively dissolve to produce a pregnant solution. They are then recovered from solution by zinc precipitation (Merrill-Crowe process) or by absorption onto activated carbon. This is followed by stripping and electrowinning. At this point, the mining company must decide whether to ship precipitates (or sponge) to refiners or to produce a dote. Some factors the company must consider are the ability to sample precipitates, concentrates or sponge, security of storage, and production rates. An important factor is the incremental cost (capital and operating) of converting precipitates or sponge into dote at the mine. Generally, mines prefer to melt precipitates or sponge to dote to avoid prob¬lems associated with sampling them. There are three types of fur¬naces used by mining operators to melt precipitates to dote. The first and most widely used is a sil¬icon carbide crucible heated ex¬ternally with a gaseous liquid fuel. The crucible is easy to use and slag can be skimmed before pouring dote. This simple system is capable of handling 1 t/a (32,000 oz per year) gold. It could cost as little as $20,000. More complex systems could cost up to $200,000. The second type of furnace is the gas- or propane-fired rever¬beratory furnace. This is usually used only by large-scale opera¬tors in the silver business. Precip¬itates in reverberatory furnaces come in direct contact with the flame. The large volumes of flue gas can carry significant amounts of dust and fume that must be re¬moved from the gas before dis¬charging it to the atmosphere. In the days when the Rand re¬finery in South Africa used reverberatory furnaces, the silver leaving the furnace in the form of vapor and fume was estimated at 2.2% of the total silver charged to the furnace. The gold in the gases was about 0.03% of the gold charged. Most of this silver and gold was recovered in the exhaust gas scrubber system. These scrub¬ber systems can be more costly than the furnace itself.

Jan 10, 1986

By Robert A. Jankowski, J. Harrison Daniel, Fred N. Kissell

Introduction Longwall coal mining in the US has steadily increased since its introduction in 1960. There are now 108 systems operating. (Sprouls, 1986). Advantages of longwall mining include higher productivity, improved safety, and greater coal recovery. Respirable dust, however, is one of the more serious obstacles to realizing the full potential of longwall mining. Early in 1980, the US Bureau of Mines (USBM) initiated extensive in-house and contract research to identify and evaluate effective methods of controlling respirable dust exposure of longwall face personnel (Niewiadomski, Jankowski, and Kissell, 1981). It was found that several control procedures must be combined to assure compliance, using control techniques appropriate to the dust source. These techniques can typically be grouped into the following categories: reduction of dust generation; dilution of dust; capture or knockdown of dust; and dust avoidance. Control techniques can be divided into basic and effective dust control techniques; additional necessary controls; and optional supplementary controls. This information should allow longwall mine operators to select control methods applicable to their particular operations and to develop a dust control plan that meets Federal dust standards. Basic and effective dust control techniques There are three basic dust control techniques (Taylor and Jankowski, 1982) that should be implemented on all longwall mining operations. • A passive barrier or external water spray system design that confines shearer generated dust near the face and away from the operators. • Large quantities of water through the sprays, particularly the drum sprays, to aid in dust knockdown and prevent dust becoming airborne. • A cutting sequence that allows the shearer operators to work primarily on the intake-air side of the lead cutting drum. Shearer clearer There are some poorly designed shearer-mounted spray systems with nozzles directed upwind at the cutting and loading zone of the intake-side drum. These actually carry dust away from the face and upstream of the drum. Where, it mixes with the clean intake air (Fig. la,) and is carried out into the walkway over the shearer operators. The Bureau developed a novel shearer spray system, called the shearer clearer. It takes advantage of the air-moving capabili-

Jan 10, 1986

By V. Rajaram

R.K. Leininger, N.R. Hasenmueller, and D.D. Carr The content of the paper by V. Rajaram does not fulfill the expectations of the title. But Rajaram submitted the article in October 1983, and he could not have foreseen the numerous developments that would occur before his paper was published more than two years later. Nevertheless, Rajaram failed to mention the interest in oil shale development in southern Indiana beginning in late 1979 and continuing through the present as a result of special financial encouragement of three oil shale projects in May and August 1984 by the Indiana Energy Development Board and the Indiana Corp. for Science and Technology. A session at the 1985 Eastern Oil Shale Symposium in Lexington, KY, Nov. 18-20, 1985, gave the current status of oil shale developments in the eastern United States. Speakers at this session reported on the three Indiana projects. First, Gary D. Aho, Cliffs Engineering Inc., spoke on a feasibility study by Cliffs Engineering and Allis Chalmers for a site-specific pilot plant using the Allis Chalmers process. The plant site is in Clark County, IN, on property of the Midwest Energy Resources Co. The project is funded by $240,908 each from the Indiana Energy Development Board/Corp. for Science and Technology (EDB/CST) and the US Department of Energy (DOE) and $120,454 from the corporate sponsors (total $602,270). Completion is scheduled for mid-1986. Next, Edwin M. Piper, Stone and Webster Engineering Corp., discussed the American Syn-Crude/Indiana Oil Shale Project. This effort followed the completion of two smaller projects funded by the Indiana EDB/ CST: "Testing of Indiana Oil Shale in a Petrosix Pilot Plant" (total funding by EDB/CST at $50,000) and "Assessment of the Petrosix Process for an Indiana Shale Oil Plant" (total funding by EDB/CST at $100,000). The status at the time of the report at the Oil Shale Symposium was that a request for an extension of time for securing nonfederal support had been submitted to the US Synfuels Corp. The proposal included building an 11-m (36-ft) diam retort in southeastern Indiana to process the New Albany Shale and to produce 366 m3 (2300 bbl) of shale oil per day by the PETROSIX process. The Indiana EDB/CST had contracted with Stone and Webster at $401,100 from EDB/CST and $245,835 from Stone and Webster for activities to advance the project in the negotiations with Synfuels Corp. At the time of the report, this project was the only eastern oil shale proposal that was still on the agenda of the Synfuels Corp. As a result of Congressional action in late December 1985, federal support from the Synfuels Corp. is no longer possible. Finally, Victor H. Carr, Eastern Shale Research Corp., described his firm's project, which is jointly supported by DOE ($227,749) and the Indiana EDB/ CST ($73,850) and is entitled "Feasibility Study to Determine Suitability of an In-Situ Process to Recover Hydrocarbons from Eastern Shale." An area in Scott County, IN, had been chosen, but not a specific 9 x 15-m (30 x 50-ft) site. One burn of a small in situ retort is contemplated as part of the project. Besides these three projects, several reports on shale research were presented. Joseph Damukaitis, American Syn-Crude Corp., reported that a pilot plant using the hydrogenation-extraction (H-E) process (described at the 1984 Eastern Oil Shale Symposium) was 94% built and would go through shakedown with oil shale but would then shift mechanical devices to process coal mine waste. Current status of research on the HYTORT process was then presented by Raymond C. Rex, Jr. Oil shale beneficiation research at the University of Alabama/Minerals Research Institute was reported by R. Bruce Tippin. Scott D. Carter discussed continued research on fluidized-bed retort¬ing of shale at the Kentucky Center for Energy Research Laboratory. Carl E. Roosmagi of DOE, Morgantown, reported on the oil shale research at the Morgantown Energy Technology Center (METC) laboratory. Henry J. Gomberg, Ann Arbor Nuclear Inc., discussed "Radiation Combined with Donor Solvents for Extraction and Up-Grading of Kerogen." Aurora M. Rubel and coauthor Eileen Davis presented results of research at the Kentucky Center for Energy Research Laboratory under the title "The Effect of Shale Particle Size on the Products from the Bench Scale Fixed Bed Steam Pyrolysis of Kentucky Sunbury Shale." Lastly, Maria Rockwell, Technical University of Nova Scotia, presented "Processing and Up-Grading of Low Grade Nova Scotia Oil Shale for Potential Use." A review of shale oil prospects by Gerald Parkinson in Chemical Engineering for Feb. 3, 1986, covers both western and eastern projects and includes a report that the US DOE is funding a few relatively small projects; most of the fiscal 1986 budget of $12 million for shale oil is for fundamental research. Projects include a $3.2 million three-year contract with Hycrude Corp. (Chicago) for development of the HYTORT process and a $1.2 million three-year contract with the University of Alabama's Mineral Resources Institute on beneficiation of eastern oil shale by froth flotation. The report incorrectly states that current projects include a total investment of $466 million in a pair of 18-month technical and economic feasibility studies for proposed projects in southern Indiana. The correct figure is $468,657 [$240,908 for the Cliffs Engineering/

Jan 10, 1986

By R. K. Singhal, H. Sahay

Introduction In terms of the world's recoverable coal reserves, Canada ranks 10th, providing 0.6% of the world's total. The US is first with 27.8% and the Soviet Union follows with 24.1%. Figure 1 shows the principal coal mines in Canada. Several provinces contain substantial coal deposits, but the largest deposits are found in the western provinces of Alberta, British Columbia, and Saskatchewan. Conservatively, 90% of the lignitic, 80% of high volatile bituminous, and nearly 100% of subbituminous, and low and medium volatile bituminous coals are located in these three provinces. During the past decade, Canadian coal production of all types increased from 18.8 Mt (2 million st) in 1972, to 25 Mt (28 million st) in 1975, to 61 Mt (66 million st) in 1984. About 38 Mt (43 million st) of this output was classified at thermal and 23 Mt (25 million st) as coking and metallurgical coal (Table 1). The three western provinces currently produce 57 Mt (62 million st) of coal - 95% of Canada's total. The remaining 3.6 Mt (4 million st) (5%) is produced in Nova Scotia and New Brunswick on the east coast. The majority of western coal (98%) is produced by surface mining methods. On the east coast, though, mining is predominantly underground and only 15% is produced on the surface. In 1985, Canada exported close to 28 Mt (30 million st) of metallurgical coal and thermal coal. During the same period, 15 Mt (16 million st) of coal were imported, mostly from western US for use in Ontario and Quebec. Almost 60% of the imported coal was used for thermal applications. The remaining 40% was metallurgical coal for the steel industry. It is generally cheaper to import coal into central and eastern Canada from the eastern US to augment local supplies rather than from western Canada. This is mainly because of high transportation costs. Mining methods The suitability of mining methods in a particular area depends largely on the geological setting. Geology, therefore, simplifies or adds complexities to mining operations, directly affecting the economics. It also influences the flexibility required from the min-

Jan 9, 1986

By K. Hanumantha Rao, A. Nayak, K. S. Narasimhan, S. N. Mahapatra

B.A. Hancock It is not at all surprising that causticized potato and potato derived amylopectin starch solutions performed much better than their parent starches. Some preparation is required to rupture the starch granules to effect the polymeric adsorption and interparticle bridging necessary for selective flocculation. In laboratory work comparing the deslime performance of causticized and autoclave cooked laboratory corn starch solution preparations, it was found that higher deslime weight rejections, with attendant proportionally greater iron unit losses, occurred with the causticized starch. These results may be specific to the ore involved but they do suggest that cooking and causticizing cause different starch granule rupture and/or starch breakdown, which have an effect on desliming response. I calculated from the data in the article that the slimes product grades were high - 24.3% and 20.3% Fe when 53.7% and 54.5% Fe concentrate products were obtained, respectively, in Table 4, and 21% Fe with a 62.6% Fe concentrate in Table 5 - using the natural tailings sample, which had a head of 34.3% Fe. It may be advisable for the authors to consider different starch preparations in future investigations. The combination of upgrading and selectivity results presented in Table 4 are not as good as the authors suggest. The authors' claim that a system has been developed to produce saleable concentrates from the Kudremukh tailings is quite disconcerting. There are many hurdles yet to be crossed before commercial application of selective flocculation becomes possible because differences between the very small-scale laboratory tests conducted and commercial application are rather large. Among the many differences are varying circuit feed grades that will occur from use of tailings, the apparent face that much lower tailings grades will be encountered in practice (it is much easier to achieve a high concentrate grade with reasonable recoveries using 34.3% Fe tailings as in the study rather than 25.3% Fe tailings grades that the plant apparently averages), the hydraulic nature of the thickeners used in operations compared to the static system used in laboratory tests, the different size distributions that will be obtained from a plant closed grinding-classification circuit, and differences in water used in a plant operation and the laboratory. The authors wrote that it was necessary to overgrind to be sure that the coarse gangue would not settle with the iron oxide floccules. This situation is likely to be exaggerated in commercial operations where it is assumed cyclones would be used for classification. Because cyclone classification is greatly influenced by particle densities, there will probably be an even greater difference in size between the iron and gangue particles in the plant, which would make the gangue slightly coarser still in relation to the iron. This would make the selective flocculation-desliming separations using the procedure employed by the authors even more difficult and, using the dispersant system the authors employed, greater overgrinding would be required. To grind finer to minimize the coarse gangue in the flocculated iron oxides is quite inefficient and appears not to broach the problem. The actual problem appears to be insufficient dispersion of the ground pulp. In this situation, addition of a dispersant would likely be required to attain a sufficiently high pulp dispersion level to efficiently effect a selective flocculation-desliming separation. Although the very coarse particles would still have a tendency to settle with the floccules, it probably would be found unnecessary to overgrind as much as indicated. Use of an optimum combination of dispersant and pH modifying reagents may also significantly improve the selectivity of desliming. Additionally, although it is possible that sufficient dispersion may be obtained by pH control alone in some situations, it is quite probable that added dispersity was obtained in the reported work from using distilled water. It is research experience that distilled water enhances dispersion. In commercial operations it may not be expected that sufficient dispersion will be obtained by pH control alone, unless the water used in the process is by nature quite dispersive. Overall, a change in the Kudremukh tailings dispersant scheme appears necessary where a dispersant is used in conjunction with a pH modifying reagent. With this change, different dispersion-flocculation responses will result that would have to be further evaluated. Therefore, it is still an open question whether an efficient and effective selective flocculation separation using Kudremukh tailings may be obtained that will produce saleable concentrates.

Jan 9, 1986

By A. L. Crandell

History The Cortez Mining District has a long history of mining activity dating back to 1862. More recently, Cortez Gold Mines had operated a cyanide leach, counter current decantation (CCD) recovery gold mill from January 1969 to February 1976. This type of plant has been standard in the US for treating higher grade, finely disseminated gold in Carlin type ores. The mill was initially operated from 1969 to 1973 at 1.5 kt/d (1650 stpd) on oxidized ore from the Cortez ore body. In 1973, the mill was operated at 2 kt/d (2200 stpd) on softer, less oxidized, high clay ore from Gold Acres, located 13 km (8 miles) west of Cortez, NV. In February 1976, the oxidized portion of the ore body at Gold Acres was depleted and the mill ceased operations. Successful heap leaching of the lower grade portion of the ores was practiced at both Cortez and Gold Acres to supplement the milling operations. Valuable experience was gained in the operation of these two heap leaching programs (Duncan and Smolik, 1977). The ore heaps at Gold Acres and Cortez were releached with a limited crew from 1976 to 1979. The surge in the price of gold in late 1979 sparked an interest to incorporate new techniques into treating lower grade and less oxidized carbonaceous ores at Cortez. In early 1980, heap leaching was started on low grade oxidized dump material left from the earlier Cortez mining operation. By June of 1980, testwork was completed on the London Extension Dump, a low grade, mildly carbonaceous dump at Gold Acres. It was decided to convert the mill at Cortez from the conventional cyanide leach CCD recovery plant to a carbon-in-leach (CIL) recovery system. In May 1983, ore processing from the Horse Canyon deposit began. The Horse Canyon ore body contains both oxide and carbonaceous ores and is located 22.5 km (14 miles) from the Cortez mill. The Cortez CIL circuit was expanded to handle a blend of oxide and carbonaceous ores from Horse Canyon. Ore selection In the last quarter 1979, gold prices were increasing to a point where restarting the Cortez mill, idled since 1976, appeared imminent. Several previously explored geologic reserves at various stages of development were available as possible sources of feed for the mill. Initial metallurgical testing of dumps and tailings from earlier operations was completed, and previously uneconomic deposits were explored. It was decided to pursue sources of ore with the least lead time to production and those with the least capital cost requirements. A master plan was developed to bring the four profitable ore resources into production. The plan called for: • Heap leaching of waste dumps from the Cortez mining operation; • Restarting the mill to handle the waste dumps from the London

Jan 9, 1986

By D. R. Nagaraj

Editor&apos;s note: Minerals concentration is a disparate area, one involving many disciplines. Flotation, flocculation, reagents, microbial processes, gravity and magnetic separation, and the areas of coal and oil shale - concentration is relevant to all of these. In his article, Nagaraj reviews the latest developments and findings in concentration that have ocurred during the past year. Flotation The Monograph Series "Development in Mineral Processing," (Elsevier, 1985) was devoted to "Flotation of Sulfide Minerals." This volume has 26 articles covering the aspects of flotation chemistry, process development, plant design and equipment, and modeling and process control. The numerous articles on sulfide flotation had one recurring theme - the role of electrochemical processes and redox potentials in flotation and depression. Significant advances have been made in this area. A differential desorption-reflotation process was developed for the beneficiation of calcitic phosphate pebble (Hsieh and Lehr, Industrial Engineering and Chemistry, 1985). The carbonate and phosphate minerals were first separated from silica using fatty acid and the modifiers diphosphonic acid and HF. The collector on phosphate was then desorbed using sulfuric acid, and calcite was selectively floated without additional collector. A two-stage conditioning - initially at pH 10, followed by that at pH < 4.5 - with sodium oleate was developed to improve the separation between apatite and dolomite (Moudgil and Chanchani, Minerals and Metallurgical Processing, MMP, 1985). Separation of Mussorie rock phosphate in India from gangue calcite, dolomite, silicates, pyrite, and carbonaceous impurities was achieved with a three-stage flotation only on -75 µm (-200 mesh) fraction (Vaman Rao et al., International Journal of Mineral Processing, IJMP, 1985). The separation of fine SiC whiskers from other products of coked rice hulls by immiscible liquid and froth flotation was achieved using M1BC, pine oil, and mineral spirits (Parekh and Goldberger, MMP, 1985). Flotation was more economical. The carrier flotation separation of hematite fines from quartz fines was effected using coarse hematite as a carrier and oleic acid and ferric chloride (Cristoveanu and Meech, CIM Bulletin, 1985). Potash recovery from brines by laboratory-pan solar evaporation and amine flotation was discussed by Foot and Juiatt (Salts and Brines &apos;85, Proceedings, 1985). Flotation in a 45-kg/h (99-lb per hour) unit recovered more than 95% of the potash in schoenite and sylvite concentrates containing 28% and 62% K2O, respectively. The effects of fresh concrete into cement and aggregate by a single-step flotation process in aqueous suspension was described (Naegle, Chemical Engineering Science, 1985). The physico-chemical principles for the selective separation of proteins from mixtures using flotation were discussed by Ostermaier and Dobias (Colloids & Surfactants, 1985). Selective flocculation of hematite from silica was studied by Bagster and Mcllvenny (IJMP, 1985). Selective flocculation was more favorable with more highly charged anionic polyacrylamides and with high molecular weight. The cationic and non-ionic polymers flocculated both minerals. In minerals mixtures, there appeared to be very little selectivity unless a combination of dispersant and electrolyte was used. The effect of dissolved minerals species, such as Cu, Fe, and Ni on flocculation of chalcopyrite, pentlandite, millerite, pyrrhotite, and covellite was studied by Acar and Somasundaran (SME-AIME, 1985). Reagents There were some major advances made in reagent development for the minerals processing industry. Cyanamid introduced several classes of collectors, one of which - the diaryl monothiophosphates as acid circuit col¬lectors of sulfides and oxidesulfide ores - was commercialized in 1985. The monothiophosphates are more stable and powerful collectors than the xanthates and dithiophosphates. Hydrolyzed dithiophosphate containing 80% monothio and 20% dithiophosphate was found to give optimum recovery of copper from crude cementation precipitate and separation of Cu and Ni sulfides from matte (Akimova et al., Obogashch, Tonkov, Rud, OTR, 1985). A new class of O-alkyl-Nallyl

Jan 9, 1986

By V. Rajaram

R.C. Rex, Jr. V. Rajaram&apos;s paper does not accurately reflect the status of Eastern oil shale development as it stands today. Today, there are numerous firms and research organizations pursuing development of the Eastern oil shale resource. Details of the current projects can be found in the symposium proceedings for the 1985 Eastern Oil Shale Symposium held in Lexington, KY, in November 1985. Additionally, the comparison of the Paraho and HYTORT processes is invalid because the HYTORT process design used it not an accurate representation of the HYTORT process. I will briefly address this point. It is disconcerting to see the author reference hydroretorting work conducted at the Institute of Gas Technology (IGT) (circa 1978) in the introduction, which indicates hydroretorting (the HYTORT process concept) yields of up to 250% of the Fischer Assay oil yield, and then turn around and base the remainder of the paper on the 1981 "Synthetic Fuels From Eastern Oil Shale Report," which depicts the HYTORT process as yielding only 115% of Fischer Assay. Indeed, work conducted at IGT to 1981 indicates commercial oil yields for the HYTORT process would be in the range of 200% to 210% of Fischer Assay. A more thorough literature search by the author would have yielded a 1981 publication by Schora et al., entitled "Update on the HYTORT Process" presented at the Symposium on Synthetic Fuels From Oil Shale in Nashville, TN, October 1981. This paper thoroughly discusses the shortcomings of the referenced study with respect to the HYTORT process. For the interested reader, I can also recommend a June 1984 report entitled "An Economic Comparison of Five Process Concepts for Using Eastern Oil Shale," published by Los Alomos National Laboratory (LA-10106-MS, Parkinson et al., NTIS No. DE84-015981). This study applies a realistic HYTORT design (circa 1982) and indicates that HYTORT is the most econom¬ical method of processing Eastern oil shales (about $20/bbl less than Paraho). Additionally, completion of the HYTORT feasibility study in June 1983 by Phillips Petroleum Co., Bechtel Group Inc., HYCRUDE Corp., and IGT has resulted in development of designs that will make the use of HYTORT on Eastern oil shales even more economic. HYCRUDE Corp., a second-tier subsidiary of IGT, is involved in commercialization and licensing of the HYTORT process and is active in efforts to develop the Eastern oil shale resource. As such, I am disappointed to see outdated material that has the potential for adversely affecting development of Eastern oil shale resources published in MINING ENGINEERING. I can only hope that this response will serve to mitigate any negative opinions that may have been formed. Today, activity in commercializing Eastern oil shales dominates the oil shale scene in the US and indicates a realization of the potential for these shales. Reply by V. Rajaram I appreciate the updates on the HYTORT process provided by R.C. Rex, Jr. I hope that Hycrude&apos;s work will lead to the funding of a pilot plant to demonstrate that yields of greater than 200% of Fischer Assay can be achieved in a commercial plant using eastern US oil shales.

Jan 9, 1986

By C. D. Elifrits, N. B. Aughenbaugh

Introduction Federal and state laws enacted to regulate coal mining and the accompanying public concern about the adverse effects that mining might have on land use have focused much attention on the subsidence of the land surfaces over underground mines. Some questions asked are: • Will abandoned mines subside in the future even though they have exhibited no surface adjustment to date? • If so, when will subsidence take place? • Can a specific surface area be affected by subsidence more than once? • What surface form will the subsidence feature take? • Is there any way to predict when subsidence will occur and end? An attempt is made here to address these questions insofar as it is possible with available data and experience of evaluation of subcritical extraction conditions. Mining that results in subsidence features can be classified as supercritical, subcritical, and critical with respect to the minimum span lengths of the worked-out rooms (Fig. 1). A complete basin will not develop fully immediately over subcritical conditions because the span lengths of the entries are less than the critical dimension (Wardell, 1983). Passageways, entries, and room-and-pillar panels are all included in the subcritical category. Because of the short span lengths, subcritical mining conditions tend to be stable over the life of the mine unless adverse geologic conditions exist (Gray et al., 1974; Dunrud, 1976). Various roof control and support procedures are employed to maintain entry stability during mining. Little information exists concerning the time factor of subsidence over areas of subcritical extraction. Data that have been collected relate to longwall mines, whereby the cavity sizes are designed large enough to induce caving behind the working faces so that complete subsidence at the surface occurs within a short period of time. The UK&apos;s National Coal Board (1975) has reduced the enormous amount of data it has collected to empirical correlations and has published these correlations in its Subsidence Engineers Handbook. The handbook states that "None of the foregoing remarks applies to pillar and stall working," with respect to the section discussing the time factor of subsidence caused by longwall mining (National Coal Board, 1975, p. 40). To understand and evaluate how time relates to subsidence above room-and-pillar mines, one must first recognize how mine cavities deteriorate and fail. The propagation of failure to the surface must then be studied, and, finally, the failures that are manifest at the surface in the form of depressions accompanied by both compressional and tensional movements must be investigated. Failure of mine cavities Any cavity beneath the earth&apos;s surface represents a condition of nonequilibrium and tends to close with time. Failure of cavities in a subcritical mine can be classified as failure of the roof, failure of the floor, failure of the supports (pillars, cribs), and elastic rebound of the rock. One mode of failure may dominate, but generally combinations of the four will occur. Also, initial instability of geologic materials and structural features and in situ stress may be unknown factors that can contribute to cavity failure. Roof failure is the most obvious opening stability problem in most operating mines. The bridging capabilities of the roof rock are dependent on the rock&apos;s material strength, geologic discontinuities, and reaction to humidity changes in the air of the mine. This type of failure may vary in magnitude from gradual flaking to massive roof falls. Mine floor instability can be manifest in the form of a general heave over a broad area or of individual pillar punching. The weaker and thicker the immediate floor material, the more prone a mine is to experience floor problems. Water seeping into an area can soften the underclay, reduce its bearing capacity, and precipitate failure of support for the overburden.

Jan 8, 1986

L.R. Bower In regard to the paper by J.B. Gwiazda, it makes a highly technical approach to show that the µ factor used by designers of lemniscate-guided roof supports has never really been confirmed as a maximum and assumes that convergence is vertical. Also, the paper does not appear to take into account deflection of structures, which occurs when the lemniscate and base members are fully loaded to their maximum stress level, nor the front to back line of the support in relation to differential roof to floor movements caused by strata movements under pressure. It is not unusual for differential movements to be slightly diagonal to the line of the support, particularly in faulted areas and on gradient faces. The paper also does not take into account consolidation of fines immediately above and below the support. Generally speaking, any differential movement is from face to waste and under these conditions the µ of 0.3, which appears to be an international standard, has worked in practice. However, if the face end of the support is lower than the waste end, then the µ of 0.3 can be considerably increased, giving rise to the damage mentioned in the paper. The ideal design should aim for a slightly forward bias in the lemniscate guide so that the last increment of setting is toward the face, tending to close any fissures that may have developed during the support advance cycle. The support should also be fitted with positive set valves to ensure that a high setting load density is attained to minimize bed separation. As far as powered supports are concerned, convergence is irresistible and all powered supports converge at their rated yield load. A similar principle can be applied to the differential roof to floor movements to drastically reduce the very high forces that would otherwise be applied to the lemniscate structures and pins and that, in turn, are transferred to the base arrangement and floor loading. Any differential movements are usually catered for by the 0.3 µ factor or deflection of structures in the lemniscate guide arrangement and consolidation of the floor. The floor loading, due to differential movement, is in addition to the support convergence load and requires additional bearing area to avoid possible floor penetration. Some seven years ago, Fletcher Sutcliffe Wild Ltd. (FSW) introduced a lemniscate-guided shield support where the lemniscate linkage is connected to the roof bar through two horizontally converging rams to allow differential movement to take place above a given rated figure. This is a known force and can be guarded against, whereas with rigid connections the forces, as yet, are unconfirmed. By careful design, a horizontal force in excess of 6 MN (60 tons) opposes differential movements for a total ram loading of only 2.5 MN (25 tons), or 1.25 MN (12% tons) each. This principle can considerably reduce the length and weight of the support in comparison with a rigid pin-type structure ; also, the yield load rating can be increased without affecting the lemniscate forces. The graph shows the tensile and compressive forces in a lemniscate linkage of a support with and without hydrostore. These forces react into both the roof beam and base members and, as can be seen from the support height to linkage load graph, a considerable reduction in these reactions is gained by the use of the FSW patented hydrostore system. Floor loading is considerably reduced under maximum µ conditions, and by allowing the roof bar to move with the strata, some degree of improvement to strata control is achieved in line with the assumptions in the paper. In practice, these movements have only been in the region of a few millimeters, which, in turn, reflects on the improvements to strata control by the addition of positive set valves. Supports to this design of both 450- and 280-t (496-and 309-st) rating have been successfully used in the United Kingdom for several years, negotiating many faulted areas without one single reported need for repair or maintenance. This includes supports left unattended during the year-long strike, proving the reliability of the system.

Jan 8, 1986

By Eileen Ashworth

Introduction A study was completed that investigated the enrollment in mining engineering programs in 24 universities and colleges. All programs considered in the study award four-year bachelor of science degrees in mining engineering. They also provide all the engineers for the mining industry and a large portion of the geotechnical engineers working on environmental problems, storage of hazardous waste, civic, and Federal government underground projects. The numbers used as the base for the study are those reported by each program to SME-AIME and published yearly (SME, 1986). Data for the study came from the period 1975-1985. Also, since some programs include students in related disciplines and special categories, such as cooperative students, a few inaccuracies were unavoidable. A 23-page document has been prepared that reports on the overall picture of current enrollment, the trends, and discusses the results, perceived effects, and what can, or should, be done. There has been an obvious, and dramatic decrease in total undergraduate enrollment since the late 1970s. In 1978, 3117 students were enrolled. In the 1985 fall semester, enrollment was 1022, less than one-third. There were 485 seniors, 265 juniors, 147 sophomores, and 125 freshmen. The downward trend in total enrollment is likely to continue for at least another two years. Class size The catastrophic drop in enrollment is shared by all programs across the country. It does not discriminate between types of programs, coal or hard rock mining, or location. In general, 1985&apos;s enrollment is about 30% of whatever the maximum enrollment was in any program, though this varies from the teens to 50%. The latter percentage occurs only for some programs with special circumstances, particularly new programs not well established in the late 1970s. The beginning of the decline in enrollment has occurred at slightly different times as affected by the demise of each program&apos;s local industry. The numbers in each class produced from a specific freshmen year (Fig. 1) are worthy of comment. The dramatic drop in enrollment for all classes after 1982 is clearly demonstrated. The timing coincides with the general downturn in the mining industry, when many employed engineers were laid off and new graduates could not find jobs. Also, significantly fewer students are being attracted to mining programs as freshmen. The number of seniors shown seems inappropriate. Where did so many seniors come from and why are so few graduates produced? There is an increasing trend for students to take four-and-a-half or five years to graduate. Therefore, they are counted twice, once when they are first classed as seniors and again the following year. Some students purposely delay graduation to obtain more summer work experience and take additional courses. They believe that this gives them a better

Jan 8, 1986

By Gerald M. Ellis

ntroduction As the gold mining industry continues to develop in the Dominican Republic and Haiti, more deposits will undoubtedly be discovered that will be amenable to development. The Pueblo Viejo gold mine is currently in operation in the Dominican Republic. It has become an important component of that country&apos;s economy. Pueblo Viejo output is important to the government as a foreign currency earner. It is also said to be among the world&apos;s more successful gold mines. But, while Pueblo Viejo is successful, no other major gold discoveries have been made in recent years. Therefore, alluvial deposits of gold have caught the attention of geologists on the Island of Hispaniola. In the past four years, exploration and investigation of alluvial deposits have been initiated in both the Dominican Republic and Haiti. This type of activity is expected to continue over the next few years. Alluvial gold mining is rudimentary gold washing, done mostly by farmers. It is an old tradition, dating back at least 100 years, and is done by small, independent, or community farming villages in the mountains and plains of the Dominican Republic. Investigations in the DR Recently, alluvial gold investigations have been undertaken in well known locations of the Dominican Republic. One is in the Villa Altagracia area. Here, the terraces and gravels of the Haina River basin were examined, test-pitted, and assayed by Minera Altagracia, a local Dominican mining group. Results led to a new investigation by the state-owned Rosario Dominicana (RD), the company that mines the gold at Pueblo Viejo. Rosario tested areas previously investigated by Minera Altagracia. RD could not define the type of concentration that could justify an industrial-scale type of exploitation. The Haina River placers are located in the flats and valleys of Central Dominican Republic. They are classified as small-scale type of operations where local cooperatives can do the traditional gold washing. It is not now considered a dredgable project for a mining company. The next alluvial gold investigation was undertaken by the Dominican Department of Mines and others in an area of some 700 km2 (270 sq miles) in the northeast near Miches. Farmers have been washing gold in streams and excavating pits in various areas, particularly La Mina and have made a living. Government geologists panned several hundred streams and river tributaries. They also washed material from deep excavations. The results, however, were negative insofar as locating alluvial gold concentrations suitable for large-scale or industrial-scale exploitation. The most favorable locations were the terraces along the Jayán and Cuarón Rivers in the area of Miches. But the grade od concentration is poor. Actually, only traces of gold were found in these

Jan 8, 1986

By M. A. Trevits, G. L. Finfinger

Various methods have been developed through US Bureau of Mines research to remove gas in advance of, during, and subsequent to mining. These include drilling horizontal or cross-measure boreholes from a mine opening, and vertical boreholes stimulated for drainage in advance of mining or for gob gas drainage. Techniques and equipment now exist that allow drilling a borehole at any angle to the vertical, and even along an arc. Stimulation treatments have also been developed that provide for increased gas production capability. This paper describes the long-term production history of five select gas drainage installations. The Bureau of Mines conducted or participated in four studies. The remaining study was conducted by the Equitable Gas Co. Principles of storage, release, and migration of coal bed gases The amount of gas contained within any given area of a coalbed depends on the coal&apos;s inherent storage capacity and the physical conditions of the coalbed. The gas storage capacity of coal is primarily a function of rank. As such, it cannot be affected by the presence of drainage holes (Kim, 1977). Certain physical conditions of the coalbed can, however, be changed that will affect the release and migration of gas. By pumping water out of the coalbed through the vertical boreholes, two important changes occur - pressure is reduced and water saturation is lowered. Reducing reservoir pressure releases gas as the coalbed adjusts and equilibrates gas to the change. Increasingly large amounts of gas are released for each incremental decrease in pressure. Lowering the water saturation level raises the permeability of the coalbed to gas and allows the gas to more readily migrate to the wellbore (Kisse and Edwards, 1975). For horizontal boreholes completed near mine openings, the coalbed has already undergone a pressure or water saturation reduction phase. This condition thus allows such boreholes to be highly productive with minimal water production. Case studies of coalbed gas production Pittsburgh Coalbed - Marianna mine 58 A methane drainage study was begun in July 1978 at Bethlehem Mines Corp.&apos;s Marianna mine 58, Marianna, PA (Fig. 1). The work was conducted in a section of the mine that was advanced 1.5 km

Jan 8, 1986

By Ian Hutchison, Ted Sluder, Jack Caldwell, Don Moore

Introduction The Cannon mine at Wenatchee, WA has recently been brought into operation to recover gold from the sandstones of the Swauk formation. The mine is a joint venture between Asamera Minerals (US) Inc. and Breakwater Resources. A tailings impoundment was constructed to impound 2.7 to 3.6 Mt (3 to 4 million st) of tailings at 1.8 kt/a (2000 stpd) over about five years. This paper describes the design and construction of the impoundment. In particular, it describes the 100 m (300 ft) high earthfill embankment that is the main feature of the facility. Project environment The project is located on the outskirts of Wenatchee, a town of about 40,000 people. The town is situated on the flat alluvial terraces beside the Columbia River. The Cascade Mountains rise from the terraces in a series of ridges and valleys. The mine is at the foot of the Cascades. The tailings impoundment is in one of the steep valleys. The climate is mild and dry (Table 1). Site selection Twelve alternative sites within a 16-km (10-mile) radius of the mine were examined. Decision making theory was used to select the most suitable site. Advantages of the chosen site include its proximity to the mine and its low visibility from points of common public access. Also, the area was already heavily impacted by an existing silica quarry. The major disadvantage of the site is the need to pump tailings over a distance of 1.5 km (1 mile) and against a static head of 200 m (655 ft). Also, it is located in a gulch just upstream from the town of Wenatchee. Site geology The impoundment is generally underlain by interbedded sandstones and siltstones. The siltstones are often shattered. The sandstones are often friable. Both rock types are extensively jointed. Some isolated faulting of the sediments occurred before the area was covered with basalt flows. About 10,000 years ago, at the end of the ice age, the basalts were covered by 3 to 10 m (10 to 33 ft) of wind blown loess - a fine sandy clay and silt. River deposits filled the base of the valley to depths between 5 and 25 m (16 and 82 ft). Under the main part of the embankment, these materials were removed to expose bedrock. Ground water flow is generally through the more permeable layers. The permanent water table is about 5 m (16 ft) beneath the ground surface. Project and impoundment layout Figure 1 shows the layout of the mine, the mill, and the tailings impoundment. The tailings deliv-

Jan 8, 1986

By H. Lyn Bourne

This is the fourth annual tabulation that gives mineral royalty information. The table presents previous information plus about two dozen new entries. In addition to the royalty information, some entries show the cost of purchased reserves. Last year&apos;s tabulation appeared in two issues, to accommodate all of the information. This year the format has been changed slightly so the table can be printed in one issue. This year&apos;s table presents the commodities in the same sequence as last year. Sand and gravel information appears first, followed by: crushed stone for aggregate; other stone; industrial sand; other industrial minerals; energy minerals (coal, oil shale, uranium); and finally metals. As always, a caveat relates to factors that influence the reserve values. The data should serve only as a general reference. The table is not intended to present an absolute scale of reserve costs. Several factors influence the value of mineral commodities. These factors include: • location and transportation costs (especially significant for most industrial minerals); • market conditions for both the commodity and the company acquiring the right to mine it; • quality or grade of the deposit as it reflects the amount of processing and beneficiation necessary to produce the finished product; • and legislative restrictions and conditions for mining a given material at a given site. These and other factors will influence reserve costs of reserves. The table shows the range of royalties and the variations in the basis of computing the fees. In a few instances, it gives the cost of acquired reserves based on purchase price and quantitative estimates of the material in place. The table lists the commodity; the location (either by state, US geographic area, or Canadian province); the cost (R for royalty and P for purchased cost); and the year in which the lease or purchase agreement occurred. The last column offers either comments or gives a footnote number for more information. The cost column requires more explanation. The units may refer to cubic yards (/yd), cubic feet (/cuft), tons (/T) (2000 lbs) or acres (/A). 1 cu yd = 0.76m3 1 cu ft =0.28m3 1st = 0.9 t7 1 acre = 0.40 ha or m2 In several cases the royalty is a percentage of the finished products, sale price and is levied against either the amount produced or the amount sold. We thank those who contributed information for the table: J. Dunn, T. Eyde, K. Loda, L. Morgan, F. Nix, H. Sorenson, and L. Williams. Several people have said they would like this to be an annual tabulation. That can happen if new information comes to the writer. What appears in the table is only a very small fraction of the cost information relative to the various commodities and the geographic areas for which there is royalty information. If you find this column of interest and possess information write or call: H. L. Bourne, c/o Neyer, Tiseo & Hindo, Ltd., 38955 Hills Tech Dr., Farmington Hills, MI 48018, (313) 553-6300. Only with new information can this become an annual and current source of reserves costs.

Jan 8, 1986

By R. G. Benson, P. R. Wotruba, K. W. Schmidt

Introduction The Fortitude deposit is located in Nevada&apos;s Battle Mountain mining district in the central Great Basin region of the Basin and Range province of the western US. The deposit is at Copper Canyon in the southernmost portion of the district, about 19 km (12 miles) southwest of Battle Mountain (Fig. 1). Mining activity in the district began in 1866 (Roberts and Arnold, 1965). Base and precious metals were mined by underground methods intermittently until 1955. Placer gold was first discovered at Copper Canyon in 1912. Moderate scale dredging of alluvial gravel at the mouth of Copper Canyon was conducted by the Natomas Co. from 1944 to 1955 (Johnson, 1973). In 1967, Duval Corp. began large scale open-pit copper mining. (Sayers, Tippett, and Fields, 1968). Copper prices decreased and precious metals prices increased in the mid-1970s so Duval&apos;s exploration efforts at Copper Canyon shifted to precious metals. These exploration efforts resulted in the discovery of the Tomboy-Minnie deposits and shortly afterward, the Northeast Extension deposit at Copper Canyon (Blake, Wotruba, and Theodore, 1984; Fig. 2). The Fortitude deposit was discovered in late 1980, after Duval had proceeded with precious metals production at Copper Canyon. Converting the existing plant facilities at Copper Canyon to a precious metals recovery system was completed in 1978 (Jackson, 1982). Production from the Tomboy-Minnie deposits began in early 1979. Precious metals production moved to the Northeast Extension deposit in 1982. In late 1984, after three years of preproduction stripping and mining of the Upper Fortitude ore zone, production from the higher grade Lower Fortitude ore zone began. Currently, Battle Mountain Gold Co. operates the Fortitude deposit. Production from the Battle Mountain mining district before 1967 included 4.6 t (150,000 oz) of gold, 65.3 t (2.1 million oz) of silver, 13.6 kt (15,000 st) of copper, 4.5 kt (5,000 st) of lead, and 13.6 kt (15,000 st) of zinc (Roberts and Arnold, 1965). At the time of Duval&apos;s 1967 start-up, ore reserves at Copper Canyon included 12.6 Mt (14 million st) in the East ore body and another 3.6 Mt (4 million st) in the West ore body. Both had average grades of 0.79% copper, 16.1 g/t (0.47 oz per st) silver and 0.86 g/t (0.025 oz per st) gold (Blake et al., 1984). The Tomboy-Minnie deposits collectively contained 3.5 Mt (3.9 million st) of ore grading 3.09 g/t (0.09 oz per st) gold and 9.6 g/t (0.28 oz per st) silver. The Northeast Extension reserves were identified as 1.4 Mt (1.5 million st) of ore with an average grade of 2.9 g/t (0.085 oz per st) gold and 5.1 g/t (0.15 oz per st) silver. Initial total reserve estimates for the Fortitude deposit were 14.5 Mt (16 million st) grading 5.14 g/t (0.15 oz per st) gold and 29.8 g/t (0.87 oz per st) silver (Jackson, 1982). Therefore, before large scale mining, the Copper Canyon area contained a minimum of 102.6 t (3.3 million oz) of gold and 541 t (17.4 million oz) of silver as mineable reserves. The Fortitude deposit reserves as of Jan. 1, 1985 were 10.6 Mt (11 million st) grading at 5.28 g/t (0.154 oz per st) gold and 28.5 g/t (0.83 oz per st) silver. Currently, the company is producing 6.8 t (220,000 oz) of gold and significant amounts of

Jan 7, 1986

By G. E. McClelland

Introduction Many discoveries have been made during the-past decade of low grade gold-silver deposits in the western US. This has stimulated development of low cost cyanidation procedures for precious metal extraction. Heap leach cyanidation techniques possess considerable potential for application to these low grade ores, small ore bodies, mine strip waste, and tailing materials where fine grinding is not necessary for good extraction. For heap leaching to be successful, these resources must have good permeability to achieve uniform distribution of the cyanide solution throughout the heaps. Some of the most difficult of the gold and silver ores to treat successfully by heap leaching are those containing excessive amounts of clays, or fines generated by crushing. Presence of excessive amounts of slimes, -50 µm (-270 mesh), in the heap leach feed will slow percolation, cause channeling, or produce dormant or unleached areas within the heap. This may result in unreasonably long leaching periods and poor extractions. In extreme cases, the clays or slimes can completely seal the ore heap. This causes the leach solution to run off the sides of the heap rather than penetrate the ore bed. The problem of heap leaching ores with fines can be aggravated while preparing ore heaps because of the natural sorting of coarse and fine material that occurs. This phenomenon results in concentration or ore fines in the center of individual ore piles and concentration of larger rock fragments of the lower slopes and base of the pile. When the individual piles within the heap are leveled off for the installation of the sprinkling system, additional segregation occurs as the fines sift through the coarser ore particles. This results in localized areas or zones with marked differences in permeability. Consequently, the leach solutions follow the course of least resistance. They percolate down through the coarse ore regions and bypass or barely wet areas that contain large amounts of fines or slimes. Effective use of marginal gold and silver resources by heap leaching required development of new methods to achieve more uniform size distribution when preparing ore heaps and better slime control during leaching. Early methods Agglomeration and balling of crushed ore to produce a porous and more uniform feed material for heap leaching is a viable method for treating clayey ores. Researchers from the US Bureau of Mines in Reno, NV began agglomeration pretreatment research in the mid-1970s for applications to and exploitation of these poor percolating feed materials. Little attention had been given to such methods before the Bureau&apos;s research. In 1905, T. C. Scrutton developed a unique technique for obtaining rapid vat leaching of a clayey ore where the gold was finely disseminated. His technique consisted of rolling the ore down a chute inclined at 60° to form agglomerates or balls readily permeable by the cyanide solution. However, these agglomerates lacked rigidity. And, to ensure good percolation leaching and washing, they could not be bedded in layers more than 1 m (3 ft) deep. If this depth was exceeded, it is difficult to obtain uniform leaching and washing. This results in reduced gold recovery. Shepard and others in 1937 studied the addition of lime and carbon dioxide or calcium carbonate to gold-bearing tailings to form agglomerates suitable for vat leaching. Satisfactory percolation flow rates were achieved in 90 g (3 oz) scale experiments, but the reagent requirements were cost prohibitive. Agglomeration and pelletizing has been used in other segments of the mineral industry. This technique was first used successfully around 1911 for pelletizing iron ores. Since then, agglomeration

Jan 7, 1986

Despite limited discussion, Chemistry of Flotation is a good text and reference 1985 by M. C. Fuerstenau, J. D. Miller, and M. C. Kuhn Society of Mining Engineers Caller No. D Littleton, CO 80127 Softcover, $23.50 (member), $18.50 (student member), $28.50 (list) Review by Richard R. Klimpel Chemistry in Flotation, as stated by the authors, is intended as a textbook for students as well as a reference book for practicing flotation engineers. It covers subject matter related to surface phenomena; collectors and collector salts; natural floatability; the flotation of sulfide minerals, insoluble oxide and silicate minerals, semisoluble salts, and soluble salts; and slime coatings. There are no discussions in the book on practical plant implications of flotation chemistry, such as the influence of rate, particle size effects, dosage, flotation equipment, and methods of chemical addition. The book itself is small (only 177 pages), and, as published, is in an easy-to-handle soft cover. Once one accepts the intent of the authors, this book really does represent a very concise and convenient summary of the chemistry of flotation. It is, however, far from complete in its discussion of concepts and implications of data. Very often in the presentation, key prior knowledge (or at least subject matter awareness) not given in the book, is assumed. Thus, depending on one&apos;s familiarity with the specific subject matter, some sections can be easily followed while others could be tough going. Some of the discussion is so brief and terse on important subjects that unless the reader already realizes the meaning of the presentation, the conclusions to be drawn are not always clear. Therefore, if one is not expecting a self-contained primer on flotation chemistry, this book is very useful. To this end, the book is recommended to practitioners of flotation chemistry. The presentation of data in figures and tables is good. It helps considerably in the book achieving its conciseness. The authors certainly are qualified and knowledgeable in the subject matter - apparent in the style of presentation. In summary, this reviewer thoroughly enjoyed this book and will use it as a concise review of flotation chemistry. Richard R. Klimpel, member SME, is a scientist with Dow Chemical Co., Discovery Development, 1776 Building, M. E. Pruitt Research Center, Midland, MI 48640. International Symposium on Blast Furnace Ironmaking, 1985, The Indian Institute of Metals, The Tata Iron and Steel Co., Ltd., Jamshedpur 831007, India, 282 pp., papercover, no price given - Papers from this symposium held in Jamshedpur, India, include the following: determination of coal and coke quality; feed to blast furnaces; burden quality and blast furnace performance; operation of blast furnaces on charcoal; review of cast house slag granulation systems; developments in blast furnace engineering and control; process improvements in blast furnace ironmaking; coal injection into the blast furnace; and coke from stamp charged coal. Advances in Materials Technology for the Process Industries, 1985, edited by H.A. Huskins, National Association of Corrosion Engineers, P.O. Box 218340, Houston, TX 77218, 273 pp., softcover, $20-This book is the proceedings of a meeting held in Atlanta, GA in October 1984. It describes innovations in metallurgy, ceramics, glass, composites, and polymeric materials that impact the integrity and economics of operating systems. It covers biotechnical developments, improvements in membrane systems, or beneficiation processes, as well as developments in electrochemical controls, testing procedures, and surveillance techniques. A Reference Guide to Mining Legislation in Canada, 1985, by B. Barton, B. Roulston, and N. Strantz, The Canadian Institute of Resources Law, Room 430, Bio Sciences Building, The University of Calgary, Calgary, Alberta, Canada T2N 1N4, 120 pp., bound, $US28- This guide provides a ready means of finding how the different jurisdictions in Canada regulate mineral activity. It covers the rights required for exploration, development, and production of mineral metallics and industrial minerals. It does not cover placer mining, petroleum and natural gas, bituminuous sands, coal, or structural materials. Dictionary of Geological Terms, 1985, edited by Robert L. Bates and Julia A. Jackson, The American Geological Institute, 4220 King St., Alexandria, VA 22302, papercover, $7.95 plus $1 for postage - This third edition is for geoscience students, teachers, and rockhounds. It defines the core vocabulary of earth sciences, contains 8000 revised definitions, and includes 1000 new terms. It adds recent terms in plate tectonics, hydrology, and permafrost studies. Accurate definitions are given without technical jargon, cross-references are included, and commonly used abbreviations are provided. Processing and Utilization of High Sulfur Coals, 1985, edited by Yosry A. Attia, Elsevier Science Publishing Co. Inc., 52 Vanderbilt Ave., New York, NY 10017, 787 pp., bound, $142.50-These proceedings comprise the majority of the papers presented at the First International conference. Investigators there reported the latest discoveries, developments in commercial practice, and state-of-the-art reviews of scientific principles and applications of various technologies for handling, processing, and use of high sulfur coals. Sessions were held on: characterization of sulfur in coals; environmental problems and impact of high sulfur on coal use; selective mining and blending; coal desulfurization by physical and chemical cleaning techniques; handling of coal fines; sulfur capture during coal combustion; biological desulfurization of coal; and new applications for high sulfur coal. The Economics of Magnesium Metal, 1985, Roskill Information Services Ltd., 2 Clapham Road, London SW9 OJA England, 129 pp., 71 tables, appendices, bound, $750-Despite setbacks in some major magnesium markets in 1985, Roskill&apos;s latest forecast for the last half of this decade is for a 4% to 6% annual growth rate in demand. Growth for magnesium metal is expected in the motor industry for use as a possible substitute for aluminum. Some magnesium producers are altering their marketing strategies to cultivate this market. This study also includes a review of the worldwide magnesium industry, its end uses and consumption, and international trade and price trends.

Jan 7, 1986

By Tim Neil, O&apos

Acid rain legislation, the new tax package, excess coal capacity, the effects of low oil prices, how to increase coal exports: These were among the items discussed at the May 4-7, American Mining Congress coal convention in Pittsburgh. Some 2000 people attended the convention, which also offered 15 technical sessions. As always, the state of the domestic coal industry might be characterized as "long-term promise, short-term problems." And one of these problems is acid rain. Acid rain The proposed acid rain legislation in Congress could be the most costly piece of environmental legislation ever written. In its present form, the measure could cost the nation up to $110 billion over the next 15 years. Rep. Henry Waxman&apos;s (D-CA) bill, HR 4567, would mandate large reductions in sulfur dioxide emissions from coal-fired power plants. The bill has more than 150 Republican and Democratic cosponsors. Ed Addison is president of the Southern Co., one of the nation&apos;s largest utilities and users of domestic coal. Addison noted that America&apos;s electric utility industry buys and uses nearly 85% of the coal consumed in this country. He said Waxman&apos;s bill would drive up prices of low-sulfur coal, raise electric rates, and force miners out of work in high-sulfur coal regions. In repeating a standard coal industry response, Addison said the Clean Air Act is doing the job. In recent years, while coal use has gone up, S02 emissions have gone down. Current air pollution standards are producing cleaner air, he said. Despite concern over HR 4567, the bill&apos;s future is uncertain. Several coal industry executives and analysts predict the bill will die under weight of opposition from coal, utility, and steel interests. But the acid rain issue is gaining momentum. Future legislation of some kind is likely. Meanwhile, research continues to develop clean coal technology to deal with the S02 problem. Commercialization of these front-end technologies currently lags public sentiment for acid rain legislation. Ground water runoff and contamination is another area where future legislation would seem likely. Already, one bill has been introduced in Congress. A second is being drafted. The impact of such legislation may be significant according to Bruce Leavitt, a hydrogeologist with Consolidation Coal Co. He said if current proposals are adopted, there will be more federal, state, and local government involvement in ground water regulation. In any event, the coal industry can expect to see more emphasis on preventing acid mine drainage and on water replacement, according to Leavitt. He urged those in the coal industry to present information about mining and ground water. That is needed to prevent misdirected state and federal programs, he said. Another coal industry concern is excess capacity. The industry has the mines, equipment, and employees to produce 15% more coal than at present. Problem is, the markets are not there. Slower-than-predicted growth in electric utility coal use has kept sales sluggish. There are also tax uncertainties. Congress is considering repeal of the investment tax credit and elimination of black lung payments and excise taxes as deductible expenses. One analyst estimates the coal industry would lose $1.1 billion in five years, if the changes are approved. In addition, there are the usual concerns about excessive governmental regulations involving safety and environmental matters. Bill Kegel, for example, said these regulations mean extra costs and delays in developing mines. Kegel is president and chief executive officer of the Rochester & Pittsburgh Coal Co. More than half the electrical power in the US is generated by coal-fired plants. That percentage could slip by a couple of points as nuclear generators come on-line the next few years. About 1990, though, we will see the end of US nuclear plant construction. No new nuclear plants have been scheduled since 1978. So any growth in electric power use should benefit the coal industry. BethEnergy - High Power Mountain During 1985, BethEnergy - a Bethlehem Steel Corp. - subsidiary developed High Power Mountain, a 1.8-Mt/a (2-million-stpy) surface mine in West Virginia. Construction saw movement of more than 3 hm3 (4 million cu yds) of earth. A computerized 544 t/h (600 stph) heavy media cyclone prep plant and a 3.6-kt/h (4000-stph) railroad loadout facility were built in six months. And a 5.6-km (3.5-mile) railroad spur and loop bridging a major highway were constructed. Larry Willison of BethEnergy noted the project&apos;s ambitious construction schedule. It was forced by the need for the project to be market driven and - lacking available capital - externally financed. BethEnergy did several things before obtaining with Detroit Edison a market for 0.9 Mt/a (1 million stpy) of coal. Willison said his company prospected and proved the eastern half of its 8-km2

Jan 7, 1986