Search Documents

By Zhigao Xu, Ming Wu, Jun Qu, Rong Zhang, Wenrui Nie, Ruan Chi, Zhenyue Zhang, Zhengyan He

The leaching processes and mechanisms of weathered crust elution-deposited rare earth (RE) ores with ammonium sulfate were investigated for their high efficiency and low consumption exploitation. The leaching process is a typical reversible heterogeneous ion exchange reaction in liquid–solid systems. The raw ore and leached tailings were analyzed by SEM and FTIR. Results indicated that no dissolution or structural changes of the ores occurred during the leaching process. The migrations of RE3+, Al3+, and NHþ 4 in the leaching process were studied under various liquid–solid ratios. With increasing liquid–solid ratio, the content of NHþ 4 adsorbed on clay mineral by physical effect decreased, NHþ 4 adsorbed by ion-exchange increased, and the content of exchanged RE and Al increased until reaching equilibrium. The adsorption capacity of the RE ores for NHþ 4 remained about 0.61–0.63 mg/g. It was difficult to desorb NHþ 4 from RE ores with washing water alone. The leaching mechanism of Al was the same as RE, but the leaching of Al slightly lagged behind RE. At the optimal liquid–solid ratio of 0.4:1, the leaching efficiencies of RE and Al were 95.51% and 90.99%, respectively, and 56.65% of NHþ 4 remained in the leachate. After impurity removal and RE precipitation, the leachate can be reused by replenishing fresh leaching agent. The aim of this study is to enhance the leaching process of RE, restrain the leaching of impurities, and decrease the consumption of leaching agents.

By Maurício Covcevich Bagatini, Maycon Athayde

Nowadays, the HPGR (high-pressure grinding rolls) is an intermediate step between filtering and balling in the most modern iron ore pelletizing operation. The operation debottlenecks filtering process and reduces pressure over the typical milling process to control particle size to the balling. The present study evaluated aspects of microwave application to the iron ore concentrate fed to HPGR in a bench scale unit. Iron ore concentrate was irradiated varying the microwave exposure time and grinding efficiency was evaluated. The moisture influence in the HPGR efficiency was also assessed. The pellet feed blaine surface area (BSA) improved by 300 cm2/g and % < 325# fraction by 3%. Scanning electron microscope (SEM) images show the formation of micro-cracks onto the particle surface induced by microwave; the effect observed helped improve the milling process performance, in addition to the moisture reduction observed due to the temperature increase.

By Guowen Dong, Qiyong Li, Qiang Li, Tiejun Chen, Zhihong Wu, Junying Wan

In order to search for a more economical and effective roasting additive for extracting vanadium from stone coal and solve the question of the disposal of PVC waste, PVC waste was proposed as a novel roasting additive to enhance extraction of vanadium from stone coal and realize the comprehensive utilization of resources. By adding this roasting additive, the leaching rate of vanadium reached 94.5% under the conditions that the PVC waste addition was 10 wt%, the roasting temperature was 800 °C, the roasting time was 1 h, the sulfuric acid concentration was 15 vol%, the liquid-to-solid ratio was 1.5 cm3 /g, the leaching temperature was 95 °C, and leaching time was 4 h, which increased by 8.4% compared with that of blank roasting. The thermodynamics calculation showed that the decomposition reaction of mica was performed easier with the participation of HCl produced by pyrolysis of PVC. Meanwhile, The SEM-EDS and aperture test analyses demonstrated that more cracks and voids appeared in the roasted sample by roasting with PVC waste, which could facilitate the release and extraction of vanadium. Additionally, the TG-DSC analyses indicated that PVC could provide large amounts of heat for the roasting process to promote the decarbonization and roasting efficiency of stone coal because of its high calorific value.

By William Gleason

During the past five years, mining operations have had access to press technology for piping and joint fittings that can save owners a significant amount of time when installing or replacing pipes by eliminating the need for welding or threading. Viega, with North American headquarters in Wichita, KA, entered the mining sector in 2009, adding to its already expanding industrial sector. Since then, the company?s global engineering department has paid considerable attention to its industrial division, bringing its expertise in plumbing solutions for residential and commercial buildings to the mining and mineral extraction industry. ?We have a lot of applications in the mining industry.?We have a lot of applications in the mining industry throughout the United States, Canada and Mexico and continue to expand in the mining industry,? Tom Shields, Viega?s director for industrial accounts explained. ?Since we made the decision to increase our presence in the industrial markets, we have been aggressive and more than 240 applications have been approved by our engineering department in Germany.? Getting approval from Viega?s engineering department is no small feat. During a tour of the manufacturing facilities in Ennest and Großheringen, Germany, Mining Engineering, as well as a select few other publications and clients, were shown Viega?s manufacturing process. At the Ennest facility, hundreds of millions of fittings are produced, and each one is inspected mechanically and with a laser at the end of the production line. With four production facilities in Germany and one in the United States, Viega is able to ship to anywhere in the world. The company distributes everything from fittings to stainless steel pipe.

By Yousef Ghorbani, Abolfazl Danesh, Fatemeh Kazemi, Ataallah Bahrami, Morteza Abdollahi, Mohammad Raouf Hosseini

This study aims to investigate the effects of operational variables on concentrate grade, recovery, separation efficiency, and kinetic parameters of the copper flotation process. For this purpose, the effects of the pulp solids content, collector and frother dosage, and preparation and concentrate collection time were studied using a Taguchi experimental design. The results of statistical analyses indicated that the concentrate collection time and pulp density were the most influential parameters on concentrate grade. Considering copper recovery, concentrate collection time, collector dosage, and pulp density were the most significant variables, in decreasing order of importance. Also, the separation efficiency was mostly influenced by the concentrate collection time. Furthermore, kinetic studies showed that the second-order rectangular distribution model perfectly matched the experimental flotation data. The highest kinetic constant of 0.0756 s−1 was obtained from the test, which was performed with 35% solids content and 40 and 20 g/t collector and frother, respectively. The highest predicted copper recovery of 99.57% was obtained from the test at 30% solids content, and the collector and frother dosages of 40 and 15 g/t, respectively

By Kirsten Corin, Belinda McFadzean, Cyril O’Connor, Jenny Wiese

The Bushveld Complex of South Africa contains almost 90% of the world’s reserves of platinum group minerals (PGMs). In the flotation of PGMs, there are significant challenges arising from the need to treat ever-decreasing grades of the relevant ore deposits. The major challenge in the flotation of these ore bodies is the control and management of the gangue minerals, particularly silicates such as orthopyroxene, plagioclase feldspar, and pyroxene which are often rimmed with talc which makes them naturally floatable. It has been shown that various polysaccharide depressants such as CMC and guar have different properties in terms of depressing the gangue minerals. Since the PGMs are often associated with sulphides, copper sulphate is widely used as an activator in PGM flotation but can inadvertently activate the gangue minerals as well as reduce the recovery of PtTe2 which accounts for up to 40% of the Pt in the Platreef ore body. Depressants also reduce the mass of solids reporting to the froth and can thus destabilise the froth. This effect on the froth can be mitigated by using higher frother dosages or water of higher ionic strength. Reducing chromite recovery is of critical importance since high levels may negatively affect the downstream smelting process. Chromite recoveries can however be reduced through the application of gravity separation or reducing entrainment through reduced water recovery. In summary, due care needs to be taken to carry out site test work to develop an optimum ratio of collector, frother, activator, and depressant to ensure that the highest grades and recoveries of the PGEs are obtained while reducing depressant dosage as much as possible.

By Jacek B. Stypulkowski

This paper discusses the challenges faced by the design team of the under-river crossings of electric transmission feeders in New York City, a densely populated urban area. The under-river crossing of a 345 kV feeder was initially designed as Horizontal Directional Drilling (HDD), but was redesigned as a utility tunnel because of site con¬straints on both sides of the river. Multiple studies addressed location, available tech-nologies and costs. Multiple soil investigation phases addressed design aspects of HDD, as well as tunneling. Contractual issues varied from a design build alternative with Geotechnical Data Report (GDR) to design tender approach with GDR & Geotechnical Baseline Report (GBR).

By I. O. Otunniyi

The natural hydrophobic response flotation method for beneficiation of printed circuit board comminution fines (PCB CF) still requires many studies to further basic understanding of the process and the flotation traits that the PCB CF presents. Varying particle size distribution (PSD) and water recovery under the scheme show that higher mass pull, obtained at the finer PSD, gave lower water recovery but higher value loss. The reverse also holds: the least mass pull at the coarsest PSD used, -106 + 75 µm, gave the highest water recovery per unit mass pull with the highest reverse recovery. This is unlike what obtains in primary resources processing, where higher water recovery is often with increased fines entrainment. The reverse recovery loss here is, therefore, more due to entrapment with the heavy mass pull characteristic of the method than to the entrainment of value with water. Other peculiarities of the system observed are discussed, with the goal of improving the performance of the process, and broadening the general knowledge of flotation systems.

By Michael Day, Paul Kos, Scott Brinton

A hydrogeologic characterization and impact analysis was performed for a proposed quarry at the Hitch Rack Ranch located in the Little Turkey Creek watershed southwest of Colorado Springs, Colorado. Continuous multiple channel tubing, nested piezometers, stream flow measurements, and mapping of known seeps were used to define the three-dimensional potentiometric distribution and areas of groundwater recharge and discharge. Water balance considerations, mass balance calculations, and potentiometric response to earth tides and barometric fluctuations confirmed that the granite fracture system in the ridge area of the proposed quarry has an extremely low bulk hydraulic conductivity resulting in minimal groundwater discharge to sustain the baseflow of Little Turkey Creek. The Little Turkey Creek valley forms the major conduit for groundwater flow exiting from the upper part of watershed underlain by granite. This conclusion has significant implications with respect to mine planning to minimize projected impacts to the hydrologic system and preserve this recharge component to downgradient Denver Basin sedimentary deposits.

By D. Berberick

Hecla?s Lucky Friday Mine is a deep, underground producer of silver, lead and zinc in the Coeur d?Alene mining district of northern Idaho. Main access into, and production from, the mine is via the Silver Shaft, a 5.5-m (18-ft) diameter, concrete lined shaft sunk by J.S. Redpath to an original depth of 1,890 m (6,200 ft) in the early 1980s. The shaft is divided into four compartments (Fig. 1), with sets made of 225 mm x 175 mm (9 in. x 7 in.) hollow structural section (HSS) steel buntons and 150-mm x 150-mm (6-in. x 6-in.) HSS dividers spaced every 4.5 m (15 ft) down the length of the shaft. Two skip compartments on the east side of the shaft are equipped with 125-mm x 150-mm (5-in. x 6-in.) HSS steel guides and 9-t (10-st) skips with three deck trailer cages for men and materials. The west side of the shaft is divided into a manway, and a fourth compartment that was originally designed for a service cage. Shaft services consist of a 250-mm (10-in.) a compressed air line and 150-mm (6-in.) sandfill line along the south side of the shaft, and 250-mm (10-in.) discharge (gray) water and 150 mm (6 in.) fresh water lines on the north wall. The mine?s primary 13.8 kV power lines, as well as communication lines are located on the west wall of the shaft. The production hoist is a 3.7-m (12-ft) diameter, double drum, double clutch, 2,238 kW (3,000 hp), direct current unit equipped, at the time, with thyristor drives. The 30-year-old drives would prove to be problematic during the rehabilitation project, leading to an upgrade to modern ABB drives later in the project, after the shaft rehabilitation was complete. The shaft had been subjected to the typical wear and tear of 30 years of operation, including intermittent sandfill and muck spills, and, in the lower areas, some corrosion. During those 30 years, the west compartment, originally designed for the service cage, could only be accessed from a work deck on top of the skips or from the manway.

By Tyler Acorn, Brandon Wilson, Jeff Boisvert

Scenario-level uncertainty is a representation of large-scale differences encountered when considering ultimate mining pits optimized over various subsets of stochastic realizations. Accounting for scenario-level uncertainty allows mine plans to be assessed against several probabilistic subsurface interpretations. Scenario-level uncertainty is found through clustering stochastic geostatistical realizations and optimizing final pits across the realizations in each cluster. Where these pits are geometrically different, plans for each scenario differ. Knowing these differences allows the value of each planning alternative to be assessed based on the value and relative probability of each scenario. These results also facilitate the use of formal decision-making frameworks for planning, leading to optimization that better represents the full statistical characterization of the deposit. An example utilizing this approach evaluates both infrastructure placement and drilling program requirements. In both cases, scenario-level uncertainty improves initial plans by limiting opportunity costs and identifying additional potential.

By Kritika Baxla, M. Mustafa Kahraman, Frank A. Drews, Yaxue Wang, Joel M. Haight, Kody Powell, Mohit Sobalkar, W. Pratt Rogers

In the opinion of these authors, technology alone can never give an organization an edge over competitors or provide an industry step change. However, history has shown that technology applied with correct logistics and strategy makes a significant difference. Never has the minerals industry faced such daunting challenges and been in such need of a step change. Application of autonomous systems has been steadily increasing in the minerals industry. Automation technology has changed the mining value chain from exploration to mineral processing and refining. The future state will only see additional in-roads of automation into more processes and the whole system design. To better understand the near-future potential of automation, it is useful to explore and review the current state of automation in minerals development. A review of the state of automation research is given. The review will consider three critical areas: automation technology, system’s engineering and management processes around automation, and the role of human factors engineering in automated and semi-automated systems. The review ends with a discussion on the social and political risks of automation in terms of shared value and sustainable development.

By Diler Katircioglu-Bayel

This study aims to investigate the effect of combined mechanical and ultrasonic milling on the size reduction of talc. Firstly, the talc sample was wet ground in a stirred media mill for five different times (30, 60, 90, 120, and 150 min), and the optimum result was subsequently achieved with treatment by ultrasonication. The effects of amplitude (20, 35, and 50 μm), solid content (2.5, 5, 7.5, and 10%), and sonication time (60, 120, and 240 min) on the sizes of the final product were investigated. The pre-milling by wet grinding caused a decrease in the grinding resistance of talc. Sequential ultrasonic treatment, which was applied to the talc sample, generated smaller particles in comparison to those acquired by stirred media milling alone. Experimental results were assessed based on the product particle size (d10, d50), reduction ratio, and specific energy consumption. Submicron particles prepared by ultrasonic treatment were perfectly stable compared to stirred media milling alone as investigated in terms of particle size. In addition, the effects of mechanical and ultrasonic milling on structural properties of talc particles were characterized by XRD analysis.

By Zhigao Xu, Ming Wu, Jun Qu, Rong Zhang, Wenrui Nie, Ruan Chi, Zhenyue Zhang, Zhengyan He

The leaching processes and mechanisms of weathered crust elution-deposited rare earth (RE) ores with ammonium sulfate were investigated for their high efficiency and low consumption exploitation. The leaching process is a typical reversible heterogeneous ion exchange reaction in liquid–solid systems. The raw ore and leached tailings were analyzed by SEM and FTIR. Results indicated that no dissolution or structural changes of the ores occurred during the leaching process. The migrations of RE3+, Al3+, and NHþ 4 in the leaching process were studied under various liquid–solid ratios. With increasing liquid–solid ratio, the content of NHþ 4 adsorbed on clay mineral by physical effect decreased, NHþ 4 adsorbed by ion-exchange increased, and the content of exchanged RE and Al increased until reaching equilibrium. The adsorption capacity of the RE ores for NHþ 4 remained about 0.61–0.63 mg/g. It was difficult to desorb NHþ 4 from RE ores with washing water alone. The leaching mechanism of Al was the same as RE, but the leaching of Al slightly lagged behind RE. At the optimal liquid–solid ratio of 0.4:1, the leaching efficiencies of RE and Al were 95.51% and 90.99%, respectively, and 56.65% of NHþ 4 remained in the leachate. After impurity removal and RE precipitation, the leachate can be reused by replenishing fresh leaching agent. The aim of this study is to enhance the leaching process of RE, restrain the leaching of impurities, and decrease the consumption of leaching agents.

By S. K. Sahoo, S. K. Sharma, A. Yadav, B. Behera, G. S. P. Singh

A field representative modeling of the gob behavior is critical for the understanding of the associated mechanics of strata behavior in longwall workings. The findings of theoretical models and laboratory tests on the simulated gob material have shown the strain hardening behavior of the gob material. The double-yield material model, which is a built-in constitutive model in FLAC3D, has significant potential to simulate the gob compaction process as it represents materials which undergo irreversible compaction in addition to shear yielding. Apart from this, several researchers have attempted using modified elastic model or applied nodal force in reaction to the strain in the gob area as per the well-known theoretical relations to meet this requirement. Although these models can simulate the mechanical response of the gob for subcritical and critical extraction widths, they do not apply to supercritical extraction width as the gob stress may exceed the in situ stress level in such cases. For overcoming these limitations, a standard approach has been developed and validated in this paper, which can be used for simulating the gob behavior in supercritical longwall workings as well. The complete study is divided into two stages wherein the laboratory scale compression test on the simulated gob material has been numerically replicated to develop preliminary confidence followed by a parametric study of the double-yield constitutive parameters for a rational estimation of their values in different conditions. The calibrated model has been used for verifying its results by plane strain modeling of two different longwall workings, using well-established empirical and analytical findings and field observations. The approach suggested in this study can be used for the efficient modeling of the gob behavior of longwall panels under varying geo-mining conditions without compromising the accuracy of the numerical model. The meticulously validated model can be helpful in rational estimation of stress redistributions around the gob area apart from load transfer on the barrier pillar.

By A. E. Sears

The intent of geomorphic landform design is to mimic the function of the natural landscape. In a surface mine reclamation application, geomorphic landform design has the potential to mitigate stream loss. This research quantified features of reference landforms and performed computer modeling of a conceptual valley-fill design using geomorphic landform principles. A design was created using published design parameters with a software design tool (Carlson Natural Regrade with GeoFluv). Three additional designs, incorporating field-obtained regional geomorphic landform parameters, were completed and resulted in a geomorphic landform design specific to southern West Virginia. This work illustrates the importance of field determination of the ridge to head-of-channel input and drainage density parameters. Values of ridge to head-of-channel distance measured in this study were consistently an order of magnitude greater than software recommended values (SRV); SRV = 24 m (80 ft) versus field= 220 m (720 ft). Similarly, for the drainage density parameter, the software recommended range is 6 to 9 km-1 (80-120 ft/ac). The field measurements for central Appalachia quantified the drainage density to range from 5 to 5.3 km-1 (67-70 ft/ac). This affects Appalachian valley-fill stream construction by making the stream lengths shorter and the land slopes steeper with straighter headwater channels compared with areas in the southwestern United States. While the application of geomorphic landform design to surface mine sites presents challenges, this work provides support for future applications.

By Eti Purwaningsih, Widi Astuti, Erik Prasetyo

Selective-reductive leaching of manganese from low-grade manganese ore using tannic acid as a reductant in acidic media was demonstrated by XRD, SEM-EDX characterization, and batch leaching studies at room temperature. The pH change in the liquid phase before and after leaching revealed that selectivity of manganese over iron was due to the hydrolysis of iron. The acidity in the liquid phase during leaching was dictated by two mechanisms: proton-consuming reaction (manganese oxide reduction by tannic acid) and proton-producing reaction (ferric ion reduction by tannic acid to produce ferrous ion). Based on the leaching studies, the more prevalent reaction between these two was determined by initial leaching conditions: tannic acid concentration, sulfuric acid concentration, liquid-solid ratio, temperatures, and agitation time. Kinetic studies revealed that maximum recovery was attained within 6-h agitation, which indicated a product layer diffusion process.

By Yousef Ghorbani, Abolfazl Danesh, Fatemeh Kazemi, Ataallah Bahrami, Morteza Abdollahi, Mohammad Raouf Hosseini

This study aims to investigate the effects of the operational variables on the concentrate grade, recovery, separation efficiency and kinetic parameters of the copper flotation process. The results indicate that concentrate collecting time and pulp density were the parameters with the greatest effects on the concentrate grade. Considering copper recovery, the concentrate collecting time, collector dosage and pulp density were the most significant variables, in decreasing order of importance. The separation efficiency was found to be mainly influenced by the concentrate collecting time. This study can be helpful in identifying the parameters with the most effects on flotation performance and, consequently, the overall process efficiency, including recovery and separation efficiency. Such an outcome can be used as a decision-based tool to apply the necessary changes in a real-life industrial operation in a more effective way to improve the quality and quantity of the flotation concentration.

By Steve Kral

The Underground Construction Association?s (UCA) 2014 North American Tunneling (NAT) conference is expected to attract about 1,000 tunneling and underground construction professionals. With the theme ?Mission Possible,? attendees from around the world will hear the latest in tunneling and underground construction technology in the two-and-a-half days of technical sessions. The meeting is scheduled for June 24-27 at the JW Marriott Los Angeles Live in Los Angeles, CA. In addition to the technical programming, the accompanying exhibit has attracted 143 exhibitors in 162 booths. And the conference will offer short courses and plenty of social activities that will provide attendees the opportunity to catch up with each other. In addition, a proceedings volume containing all of the 128 papers will be available. An impressive lineup of sponsors will help attendees enjoy the conference. They include Brierley Associates, Kiewit Infrastructure Group, Parsons, Skanska, Traylor Bros., MWH and HNTB.

By D. Parks, A. Miller, M. McNinch, R. Jacksha

Each year, hundreds of mine workers are involved in machinery-related accidents. Many of these accidents involve inadequate or improper use of lockout/tagout (LOTO) procedures. To mitigate the occurrence of these accidents, new safety methods are needed to monitor access to hazardous areas around operating machinery, improve documentation/monitoring of maintenance that requires shutdown of the machinery, and prevent unexpected startup or movement during machine maintenance activities. The National Institute for Occupational Safety and Health (NIOSH) is currently researching the application of Internet of Things (IoT) technologies to provide intelligent machine monitoring as part of a comprehensive LOTO program. This paper introduces NIOSH’s two phase implementation of an IoT-based intelligent machine monitoring system. Phase one is the installation of a proof-of-concept system at a concrete batch plant, while phase two involves scaling up the system to include additional sensors, more detailed safety/performance metrics, proximity detection, and predictive failure analysis.