Search Documents

By N. O. Lotter

The reliability of a set of flotation results is key to minimizing project risk, either at the commissioning of a concentrator or at the point of implementing an improvement to an existing concentrator operation. High-confidence flotation testing (HCFT) was developed for this purpose and is part of the list of technologies at various scales used by Xstrata Process Support (XPS) in addressing these projects. The methodology is based on two principles: one, to ensure that the ore sample is representative and has been well-blended and subsampled; two, to perform the flotation tests in sufficient numbers of replicates with appropriate quality controls, so as to improve the reproducibility of the test data. Across ten years of research on this methodology at Xstrata Process Support, Sudbury, several improvements to the HCFT method and complementary connections between sampling and quantitative mineralogy have been developed. Two case studies are reviewed. These show the capability of this system in both optimizing an existing concentrator operation and in serving a new mine scenario. Further work to improve the efficiency of this procedure has been identified. Key words: Flotation testing, Flotation

Jan 1, 2010

By N. O. Lotter

The reliability of a set of flotation results is key to minimizing project risk either at concentrator commissioning, or at the point of implementing an improvement to an existing concentrator operation. High-Confidence Flotation Testing was developed for this purpose, and is part of the list of technologies of various scales used by Xstrata Process Support (XPS) in addressing these projects. The methodology is based on two principles: one, to ensure that the ore sample is representative and has been well-blended and subsampled; two, to perform the flotation tests in sufficient numbers of replicates with appropriate quality controls, so as to improve the reproducibility of the test data. Across ten years of practice and continuous improvement with this methodology at Xstrata Process Support, Sudbury, several improvements to this method and complementary connections into sampling and quantitative mineralogy have been developed. Two case studies are reviewed. These show the capability of this system in both optimizing an existing concentrator operation and in serving a new mine scenario. Further work to improve the efficiency of this procedure has been identified.

Jan 1, 2009

By Thomas Oberndorfer

INTRODUCTION Since several years the author is engaged in research activities in the field of mining method modelling (Oberndorfer, 1993 and 1994). The initial goal was to improve and assist the selection of the most appropriate mining method. However during investigations it became obvious that the most beneficial application of computer support is the fast calculation of numerical assessment rather than the consideration of all, i.e. also qualitative, criterions necessary for final decision. Numerical results serve - together with qualitative considerations based on the experience of the mining engineer - as a basis for decision. The emphasis is on "fast" calculation, as only this property makes it possible to calculate and compare many distinct variations. As long as no procedure exists, which optimizes all involved parameters, calculating many variations is of great important, because it is the only way to increase the chance to pick a alternative "close to optimum", but also to learn about the sensitivity the result will react on changes of input parameters, which are rarely known exactly. Generally speaking many trials give a better basis for final decision. It is no secrete that the most important obstacle towards quick calculations of a series of alternatives is not the processing time of the computer, but the time required for setting the input data in way that the computer can start processing, which is usually inter- active man work on the screen. Furthermore usually several distinct programs are required to cover the whole range of involved problems, with corresponding problems in automatic data transfer. The research work's goal was to overcome these problems. The approach developed was to describe a mining method more in a theoretical way (i.e. to give the computer some degree of "consciousness" on mining methods), which then can be applied under any specific conditions. E.g. a cut-and-fill operation will be "generally" the same in narrow or thick deposit areas, but the resulting keyfigures, e.g. total tonnage, productivity, dilution and loss, or finally costs per ton, will differ significantly. The approach (MMM = mining method modelling) presented reflects a deduction from the general case to a specific one (rather than the other way round). The developed model is general enough to be applicable to any mining method, and also to any degree of precision the mining method should be described, contrary to programs designed for specific mining method layouts which can be adjusted in a more or less wide range. PROGRAM DEVELOPMENT The principle correctness and feasibility of the approach was proved by a prototype program. However this program was more on a research level and far away from application for "real world" problems. The reason for this was, that it was regarded wasted time to re-invent certain tools, e.g. geometry intersection, deposit modelling or visualization. Hence it was tried to attract several software producers to invest in finalizing the model. Unfortunately this endeavor was not successful. Despite this defeat - and after some months of resignation - a final start on the project was decided. he reason for this decision was not at last the research activity in respect of low-cost underground mining methods for bulk- material as a substitute of typical quarry operations due to environmental restriction. This research work - which is in particular important for Austrian mining activities in beautiful and touristically used landscape - requires a lot of calculations in the way described. Both are still in state of progress, but - regarding mining method modelling - preliminary results can be presented. A complete re-programming of the program was required. Most obvious are the changes of programming language and operating system environment. Instead of Pascal under DOS C++ under MS-WindowsNT is now used. Several problems could be solved by this, in particular memory management, device drivers for input/output, and user friendlyness by up-to-date windows technology. However also more basic structures were changed. The idea was to utilize as many existing commercially available programs as possible to minimize programming efforts. WindowsNT helps already a lot by MFC technology, but also due to its multi-task facilities. This feature allows to run simultaneously several pro-

Jan 1, 1996

By Chris J. Conway, Bruce W. Atkinson, Graeme J. Jameson

The flotation of coal in the fie and coarse particle size ranges presents particular problems. Fine or ultra-fine coal less than 100 microns presents a challenge to conventional flotation machines because the rate of capture of the coal particles can be very low, so longer residence times are needed. Also, conventional mechanical cells are not normally designed with froth properties in mind. Froth drainage may be inadequate, leading to excessive entrainment of ash. The upper limit of flotation of coal is normally put at about 500 um (30 mesh). It appears that, in mechanical cells, coarser particles tend to be torn away from bubbles in the turbulent environment created by the impeller. In this paper, results are presented from plant trials of a high-intensity flotation column of novel design, namely the Jameson cell. Extensive trials have been conducted on coal slurries with a top size of around 1 mm. Size-by size analysis shows that it is possible to achieve high yields of low ash product over the whole particle size range.

Jan 1, 1995

By Richard Cole

The Energy Act of 1992 has many users of ac-induction motors eyeing premium-efficiency motors with mixed feelings and perhaps some confusion. When the October 1997deadline arrives for compliance with the1992 standards, the winners will be the environment due to reduced need for more power generating plants and the petroleum economy because of reduced dependency on foreign oil. But what will it mean for industrial users? The most obvious benefit is the potential for smaller electricity bills. Motors account for about 64% of the electricity consumed in the United States, at a yearly cost of $112 billion. Every 1% reduction in motor demand cuts 0.64%, or $716 million, off the industry wide bill. Higher efficiency motors also run cooler. This lightens the load on air-conditioning systems and further reduces plant demand. Lower total demand can lead to lower rates by helping to minimize peak-demand surcharges. As rates increase over time, these savings get bigger.

Jan 1, 1996

By E. E. Bauer

Oversize boulders in mines and quarries must be broken for waste disposal or further processing of ore. Early methods involved drilling and "shooting" or using a drop ball of sufficient weight to accomplish the purpose. The first "high-energy" hammers for breaking concrete or boulders were pneumatically operated. Blow energy was limited by valving and air pressure. However, smaller boulders of lower compressive strength could be broken. A hydraulic excavator-backhoe type machine was required for either a drop ball or hammer. Standard practice was to break oversize boulders in the pit before hauling to the grizzly or crusher. Generally, quarry boulders were not valuable enough for further processing. Quarry roads were lined with oversize boulders. As safety requirements were advanced, "drill and blast" for boulders was ruled out.

Jan 1, 1994

By Ivor Hawkes

INTRODUCTION High energy breaking is an alternative to using ex¬plosives in underground secondary breaking operations. It also is a means of upgrading conventional hand-held breakers, manual sledge-hammer breaking, and scaling bar operations. Major areas of application are in sec¬ondary breaking over grizzlies and at drawpoints. Other applications include breaking down ripping lips in longwall seam mining, scaling in stopes and rooms, general demolition work, and roadway maintenance. There is considerable interest in high-energy impact breakers for use in primary ore breaking, but, as of 1977, all such applications have been only experimental (duToit, 1973; Joughin, 1976; Wayment and Grantmyre, 1976). EQUIPMENT Essentially, a high-energy impact hammer is a boom¬mounted pneumatically or hydraulically actuated breaker. The machine basically consists of a piston that oscillates in a housing and impacts the end of a tool or moil thrust against the rock. The force applied to the rock primarily depends upon the impact energy of the piston-the higher the impact or blow energy, the greater the force and, thus, the greater the rock break¬age. Among drill and breaker designers, a common expression for blow energy is "force of blow." Hand-held breakers are limited to blow energies of about 140 J (100 ft-lb), because the operator is unable to handle heavier machines efficiently or to absorb the recoil energy resulting from higher blow energies. How¬ever, these restrictions do not apply to boom mounted breakers; machines with blow energies on the order of 4000 J (3000 ft-lb) and higher are available commer¬cially for underground use. There is considerable evi¬dence to show that increasing the blow energy also in¬creases the efficiency of the breaking operation; i.e., more rock is broken per unit of energy expended (Grantmyre and Hawkes, 1975). Thus, there is a trend to higher blow-energy machines, particularly where high¬strength rocks are to be broken. In relation to rock breaking, the blow rate of boom¬mounted impact breakers is not as important as it is for rock drills. This is because the breaker must be moved over the work surface between blows. The blow rate is governed eventually by the power supply, and typical blow rates range between 200 and 600 blows per minute. As a general rule, light blow-energy machines have higher blow rates than heavier machines. Table 1 lists most of the boom-mounted impact breakers that were available commercially during 1977, and it gives details of the blow energies and machine weights. Restrictions are placed on the blow energy by the machine weight and size, and by the strength of the boom. Typically, boom-mounted impact hammers have a blow-energy to mass ratio of about 1.5, with lower values for lighter machines and higher values for heavier machines. In addition to supporting the hammer weight, the boom also has to absorb the recoil energy of the blow, which can be on the order of 1400 J (1000 ft-lb) for large hammers operating in a horizontal mode. Interesting exceptions to the general run of impactors are the Joy HEFTI hydraulic hammers. In these machines, the piston impacts onto a fluid cushion that is positioned between the piston and the impact tool. This approach allows very high piston velocities, over 30 m/s (100 fps), to be used without the risk of break¬ing the piston or impact tool. Steel on steel impacts must be limited to impact velocities of about 10 m/s (35 fps) due to the high impact stresses generated; thus, increased blow energies can be achieved only by increas¬ing the piston size. The Joy 514 HEFTI®, listed in Table 1, has a blow energy of 27 100 J (20,000 ft-lb), but, as of 1977, the machine has been used underground only on an experimental basis. Using a fluid cushion between the piston and the impact tool allows the use of light pistons, reducing the overall machine weight. The recoil energy, which must be absorbed by the boom for a given blow energy, is directly proportional to the piston to machine mass ratio, and operating with light pistons provides an addi¬tional benefit in reducing the requisite boom size. Both pneumatic and hydraulic hammers are avail¬able commercially. Although hydraulic hammers are a relatively recent development, they already outnumber the pneumatic machines in use. There are many reasons

Jan 1, 1982

By Marie-Josée Banwell, Cyriac Sebastian, Giacomo Falorni, Sara Del Conte

Interferometric Synthetic Aperture Radar (InSAR) is a satellite-based monitoring technique that complements other in-situ methods for detecting and measuring surface displacement. Recent advances in data processing algorithms, coupled with the use of high-resolution satellite systems, make it possible to now provide high-frequency InSAR monitoring services, with updated results delivered every time a new satellite image is acquired. The advent of large, continuously updated data sets, however, brings new challenges, including the need to rapidly sift through the data to identify only those points showing relevant ground displacement information. This has been achieved by using trend variation analysis tools, that quickly isolate and highlight only areas of anomalous behavior. The paper focuses on project case studies where continuous InSAR monitoring has proven to be key in identifying displacement trend changes near tunnel alignments.

Jun 13, 2021

By Henrique D. G. Turrer, Robert F. Winterfield, Jobe E. Wheeler, Marcello R. Cru, Baojie Zhang, Pedro P. Pinto

Efficient particle classification is essential to enhance gravity and magnetic separation stages in one iron ore beneficiation plant. This study investigates the use of high-frequency screens to process finely ground iron ore, focusing on two size cuts: 400 μm and 100 μm. Pilot-scale trials were performed on four ore blends using a full-scale screening unit. A total of 48 tests were conducted, evaluating the effects of panel aperture, solids concentration, wash water, and feed particle size distribution. Results showed that wash water improved efficiency by up to 5%, while a solids concentration near 40% w/w delivered high separation performance with minimal ultra-fines in oversize streams. Apertures slightly larger than the target cut sizes yielded better precision in particle separation. Feed particle size distribution had limited impact on efficiency. The investigation successfully identified optimal screening conditions, including aperture selection, to achieve the most effective separation performance for downstream concentration processes.

Feb 22, 2026

By C. D. Harrison

This paper presents the results of 18 high-G centrifuge tests performed at the Electric Power Research Institute's Coal Cleaning Test Facility in January 1985. These tests, using -28 mesh (0.6mm) froth flotation product, show that the high-G, solid-bowl centrifuge can produce clean-coal moistures of less than 12 percent at solids recovery rates exceeding 98 percent. The high-G centrifuge achieved these low moistures by applying centrifugal forces up to 2,000 times gravity. Because these forces are two to three times the forces used in a screen-bowl centrifuge, the high-G centrifuge can use a solid bowl and still produce a low-moisture product. The solid bowl captures ultrafines that would pass through a screen bowl, and thus obtains higher recovery rates than a screen-bowl centrifuge.

Jan 1, 1985

By d&apos, J. A. Oliveira, A. K. L. Resende, L. F. G. Assumpção, J. D. Neto

Kaolin samples from Rio Capim Resources were treated in conventional and superconducting magnetic separators to study the main variables that influence the impurity removal process. Two coating clays and a delaminated clay were tested. The variables studied were retention time (cross-sectional velocity), magnetic-field intensity and matrix type. The feed brightness ranged, from 84.7% to 87.6% ISO, for the coating clays and ranged from 80.7% to 85.4% ISO for the delaminated clay. Using a conventional magnetic separator with an applied, field of 1.5 to 2.0 T (tesla), the brightness values were higher than 88% ISO for the unleached coating claw products and were higher than 87% ISO for the unleached delaminated product. With a maximum field intensity in the superconducting machine of 5.0T unleached brightness values higher than 88.5 % ISO were attained for both coating and delaminated clays.

Jan 1, 1997

By Arthur G. Strassburger

INTRODUCTION High in the Sierra Nevada Mountains of California, some 50 airline miles (80 km) northeast of Fresno, and near the John Muir Wilderness and Kings Canyon National Park, a large underground hydroelectric project is under construction. Pacific Gas & Electric (PG&E) Company's 1,125 MW Helms Pumped Storage Project exhibits a number of impressive statistics, unusual features, and other characteristics of interest to the tunneling or power plant designer and construction contractor. The most significant underground facilities include almost 20,000 ft (6,096 m) of 27-ft (8.2 m) diam concrete-lined pressure tunnel; 3,700 ft (1,128 m) of access tunnel; 1,600 ft (488 m) of steel-lined high-pressure conduit, 2 major underground chambers more than 1,000 ft (305 m) below ground; 3 deep vertical shafts, and one steep inclined shaft. Maximum static pressures within the conduits range from 200 ft (61 m) to 1,744 ft (532 m), with hydraulic transients that increase pressure to 2,500 ft (762 m). The purpose of these underground works is to provide 475,000 hp (354,350 KW) of water power to each of the 3 reversible pump-turbines, each connected to a 375 MW generator motor. The units, rated at 1,744 ft (532 m) maximum static head, are among the world's front-runners, considering the size-head combination. The Helms Project develops the existing power drop between two of PG&E's reservoirs, Courtright Lake and Lake Wishon. These reservoirs are retained by two concrete-faced rockfill dams completed in 1958, each storing approximately 125,000 acre ft (154 x 106 m3) of water. Although the project is intended to operate on a typical

Jan 1, 1981

By David I. Dr. Hoyer

The Hicom mill is a conical mill in which a ball or autogenous load tumbles within a high-intensity acceleration field. An autogenous Hicom mill with a power density of about 1100 kw/m3 and a volume of just 4 litres reduced a 50 m quartzite feed to 90% passing 38 microns at a feed rate of 160kg/h (in closed circuit with a hydrocyclone). Batch tests have identified fracture, chipping and abrasion breakage mechanisms at pebble sizes of 5 to 50 mm. The special behaviour of the load in Hicom mills was exploited to develop a novel technique for estimating steady state autogenous load size distributions.

Jan 1, 1992

By E. Yan, M. Mankosa, G. Luttrell

"During the past decade, column flotation cells have become widely accepted for upgrading ultrafine sulfide ores. However, the use of columns has been widely relegated to cleaner circuits due to their comparatively high selectivity derived from the use of wash water dispersed over a deep froth. High tonnage rates and low feed grades make using column technology in roughing and scavenger stages challenging due to the resulting size of the needed equipment. To specifically address this challenge, a new high-intensity flotation system known as the StackCell™ was developed. This technology makes use of a novel pre-aeration method coupled with froth washing to simultaneously provide improved flotation kinetics and selectivity. The novel aeration system provides efficient bubble-particle contacting thereby shortening the residence time required for particle collection. This article reviews the technical design features of this new flotation technology and presents recent data from in-plant pilot testing in a copper-sulfide application. INTRODUCTION Column flotation cells have become very popular in the minerals processing industry for cleaner circuits due to their ability to produce a high-grade froth concentrate via the use of froth washing (Luttrell et al., 1999; Kohmuench et al., 2004). The use of wash water minimizes the nonselective recovery of ultrafine impurities that are normally entrained into the froth product from conventional flotation machines. On the other hand, the unique design of a column cell typically requires a large tank volume. Column cells must be tall to ensure that the pulp residence time is long enough to offset their inherently slow flotation kinetics and to minimize internal mixing that is detrimental to overall cell performance. The tall design minimizes the total floor space required for the column installation, but substantially increases the foundation load. The large size of the column tank can also create issues during fabrication, transportation and installation. To address these concerns, the engineering team at Eriez Manufacturing developed a next-generation flotation technology called the StackCell?. This high-intensity flotation machine was designed to provide column-like separation performance within a very compact volumetric footprint. This article describes the key working features of this new technology and provides data from recent pilot-scale tests conducted in gold and copper-sulfide applications"

Jan 1, 2016

By Koehler Stout, Leroy Friel

INTRODUCTION Hydraulic sand fills have been extensively used in the United States in deep metal mines since 1940, and hydraulic fills have been placed in coal mines in Europe for many years. Numerous surface hydraulic fills exist in Appalachia for the disposal of coal mine waste and throughout the United States for the disposal of other mining, manufacturing, city, and paper company wastes. Hydraulic fills, as they are now deposited in stopes in mines, are often deposited at near minimum density and hence provide very little support to stope walls and pillars. If the support strength of fills could be increased, perhaps ground conditions in deep mines could be improved making them safer and more efficient. Surface fills deposited at higher densities could be covered with top soil upon which grass could be planted. The purpose of this paper is to describe procedures where the support strength of hydraulic fills can be considerably increased, and the focus of the paper is on applications to deep mines. In deep mines the objective of increased fill strength is to reduce heavy ground problems, improve destressing techniques, reduce or eliminate rock burst incidences, provide better working conditions, provide wall support so that more or all ore pillars can be removed, and improve mine safety, efficiency, and reduce surface environmental problems. The authors have shown that it is possible to improve fill strength used in deep mines. This paper reports the slurry filling procedure, fill testing techniques, and some recommendations for application in deep mines. Some of the reasons for low strength hydraulic fills are:

Jan 1, 1979

By L. Thompsen

High-pressure grinding rolls (HPGR) offer capacity increases, savings in operating costs and metallurgical advantages. The first installation of the Polycom HPGR in a copper ore treatment plant occurred in July 1995 at Cyprus Sierrita’s mining complex near Green Valley, AZ (Fig. 1). Until that time, the benefits this technology offers for copper and gold ore were only demonstrated on testwork. In other industries, such as diamonds, HPGR have proven to be reliable in industrial-scale plants and have set a new standard for this kind of ore treatment plant. HPGR are also successfully used for the comminution of coal, blast furnace slag and in cement and pelletizing plants. The installation at the Cyprus Sierrita Mine should prove the economical benefits in commerical-scale copper mining, confirming the results of comprehensive testwork(Fig. 2).

Jan 1, 1996

By Michael von Seebach

High-pressure grinding rolls subject the feed material to pressures of 200 N/mm? During this process considerable size reduction and the Formation of flakes occur. This paper describes the basic consideration For design and operating of this type of mill. It is also shown that the particle size distribution resulting from this process is typical for grinding processes but untypical for crushing processes. High pressure grinding rolls are designed in size of up to 2.8 m roll diameter allowing feed material top sizes of 250 mm. The rigid frame, bearing and drive - train design allows a broad application of the high-pressure grinding rolls operating the machine in open or semi-closed and closed circuit for dry and moist feed materials. Operating results show that capacity increases of up to 100 % can be accomplished with this technology. The high-pressure grinding roll also, allows for lower operating and maintenance costs due to energy savings of up to 20 L and reduction of wear to less than 1 76 for dry and less than 0.1 5 for wet grinding. Other advantages of the high-pressure grinding rolls are smaller equipment sizes than a ball or SAG-mill for a given capacity resulting in lower building sizes with reduced capital in- vestment costs.

Jan 1, 1987

By Oliver Gutsche

High-pressure roll mill comminution of heterogeneous multicomponent feeds was simulated with artificial limestone-quartzite mixtures using a piston-die press. The influence of heterogeneous interactions between components of the mixture on grinding path, energy utilization and energy split have been examined. Primary fractures are governed by differential fracture strength and attrition resistance of the components at heterogeneous contacts; subsequent secondary and tertiary fracture events are governed by coarse-fine interactions in the particle-bed. The weaker component is preferentially ground out of the feed size fraction and concentrates in the fines. Energy split among the components in the mixture is a function of their relative fracture strengths. It doubles for limestone and decreases by a factor of 5 for quartzite over the entire range of the mixing ratio.

Jan 1, 1995

By Tim Lundquist

Disa Technologies Inc. provides innovative, sustainable solutions for mineral processing and remediation through its patented High-Pressure Slurry Ablation (HPSA) technology. HPSA processes solid feed material in slurry form, propelled by high pressure pumps through opposing nozzles that generate impinging jets within a collision housing. This process induces particle-to-particle collisions in a high energy zone, creating intergranular fractures along grain boundaries. In our batch scale and continuous operating testing, we have found that controlling key processing variables such as nozzle velocity, slurry solids percentage, and the number of passes can allow for controlled size reduction and maximum mineral liberation. Since 2018, Disa Technologies has demonstrated the versatility of HPSA by testing it on diverse materials, including phosphate, copper, uranium, vanadium, zinc, rare earth elements, lithium, nickel, mineral sands, gold tailings, and more. The intent of this paper is to present an overview of our test results describing in detail impacts on size reduction, recovery, and grade with a focus on HPSA's adaptability across ore types. Looking forward, it explores the potential to process materials such as DR-grade iron, clay, PGMs, bauxite, and various tailings. Additionally, it examines planned advancements in HPSA technology, including optimized nozzle spacing, higher capacity models, improved tonnage-to-footprint ratios, enhanced maintenance features, and expanded nozzle configurations.

Jan 1, 2025

By Isobel Yeo, Luca Cocchi, Sven Petersen, Nico Augustin, Sean Plunkett, Ingo Klaucke

Exploration for seafloor massive sulfides is currently mainly focused on investigation for active hydrothermal vent fields. However, most of the resource potential is thought to be related to inactive, large deposits that had enough time to accumulate sufficient tonnage. At the same time, ageing of these deposits will ultimately result also in burial acted by either sediments and/or volcanic deposits. We currently lack the technologies to explore for these deposits in a time- and cost-efficient manner. In the fall of 2012 we used a number of AUV-based technologies to explore and image a sulfide occurrence at the Palinuro Volcanic Complex in the Tyrrhenian Sea (Mediterranean Sea; Fig. 1) where sampling and drilling have documented a buried polymetallic barite-pyrite dominated site (Petersen et al., 2014). Sulfide mineralization is here covered by volcaniclastic and pelagic sediments and only red sediment staining and the presence of few tubeworm bushes indicated recent hydrothermal activity - black smoker venting is absent. We used AUVbased high-resolution bathymetry, sidescan sonar imaging, subbottom profiling, as well as magnetics to describe, in a quantitative way, the previously known sulfide-bearing areas as well as to successfully explore for new hydrothermal sites including large chimney structures (Figs. 2). Additionally chemical sensors (CTD, Eh, turbidity) investigated the water column for signs of hydrothermal activity in areas not previously investigated, but at the end, only weak anomalies were found in the southern part of the summit.

Sep 1, 2014