Search Documents

By S. A. Sanderson

The last two decades have witnessed the resurgence in popularity of a century old tool for shaping laws and public policy – the ballot initiative. In recent years, anti-mining special interests have used the initiative process to secure voter approval of measures to ban modern surface mining for gold and silver. In November 1998, voters in Montana approved such a measure1 – the effects of which have been devastating to the mining industry in that state. In November 1999, anti-mining groups sought to place a nearly identical provision on the general election ballot in Colorado. They did not succeed, but the battle over mining’s future continues in the most important forum of all – the court of public opinion. The Colorado measure failed, in large part, because its proponents failed to convey a positive environmental theme. The mining industry also exercised early-on the rights available under state law for administrative and judicial review of the initiative, instead of relying upon the limited relief that would have been available had it waited until after the secretary of state approved the measure for the November election ballot. This article will summarize the ballot initiative process in Colorado and the proceedings that took place over Initiative No. 215.

Jan 1, 2001

By Ronald E. Heuer, Debra L. Virgens

INTRODUCTION Behavior of clay soils in response to tunneling is reasonably well understood by reference to the tunnel stability factor NT = Pz/su (Peck, 1969; Heuer, 1974). With this analysis tool, care must be taken to use a value of clay shear strength which represents the actual mass strength, considering such factors as slickensided fissures often found in stiff and hard clays. Behavior of clean sand and gravel soils is also reasonably well understood. Above the water table these soils must be assumed to act as running ground unless they are known to have significant cementation or have a very dense and angular interlocked grain structure. Below the water table they must be tunneled using some form of groundwater control such as dewatering, grouting, freezing, or internal fluid pressure in the tunnel such as compressed air or a slurry tunneling machine. The internal fluid pressure must approximately balance the external water head. Without such precautions these soils behave as flowing ground and may yield large volumes of water flow into the tunnel. A wide range of very fine sand, silty sand, cohesionless silt, and clayey sand soils exist in nature in a variety of geologic environments. The behavior of these soils in response to tunneling, and guidelines for anticipating their behavior, are not well described in the literature. Because of their content of fine particles, these materials may behave as if they initially have appreciable cohesion and moderate to low permeability. They may exhibit significant standup time, and require tunnel internal fluid pressure (compressed air or slurry pressure) less than the full external water head. It is important to be able to estimate the behavior of these soils when planning construction methods. For example, if the external water pressure is 140 kPa (20 psi), but soil stability at the tunnel face can be achieved as a compressed air pressure of 80 kPa (12 psi), a large cost savings may result.

Jan 1, 1987

By D. B. Desai, J. T. Waggoner, J. S. Hill, R. R. Redd, S. J. Klein

The 13 km (8 mile) long Riverside Badlands Tunnel is planned for construction starting in 1998. Extensive geotechnical investigations indicate that the 3.7 m (12 ft) finished diameter tunnel will be excavated through soft ground, weak sedimentary rocks, and heavily fractured metamorphic rocks. Nearly 80 percent of the tunnel will be excavated beneath the groundwater level. Tunneling conditions are expected to range from raveling and over-stressed in the sedimentary rocks, to blocky and seamy/crushed with some squeezing in the metamorphic rocks. Two alluvium reaches will require dewatering. The variable and interspersed ground conditions are expected to be a key factor in selection of tunneling methods, equipment, and initial support.

Jan 1, 1997

By W. H. Dickinson

The performance of seven antiscalants spanning a range of chemistries was evaluated for control of calcium carbonate (CaCO3) formation in gold processing applications. Three preferred chemistries were identified which provided up to 100 percent inhibition in static jar tests when applied at 30 ppm dosage. The three products were further evaluated using a model carbon extraction circuit developed for this application. The test circuit enabled direct measurement of calcium carbonate formed on the carbon from a supersaturated solution under dynamic conditions. The antiscalants lowered CaCO3 buildup on the columns by 15 - 26 percent compared to untreated controls. Impact of the antiscalants on the rate and extent of gold loading onto a carbon adsorbent was evaluated in laboratory carbon-in-pulp (CIP) studies. The antiscalants generated a 25 - 35% increase in gold loading at gold extraction efficiencies up to 65%. On-site testing at a gold processing facility demonstrated that 10 ppm of the preferred antiscalant was able to fully suppressCaCO3formation in thickener overflow water.

Feb 27, 2013

By James H. Nulty, Joseph S. Roti

INTRODUCTION During a recent panel discussion on the topic of millwater antiscalants, the question was posed: "What would you like to see in the future?" Answer: 'We need an antiscalant that: can be fed without a pump (no maintenance), functions on residual basis (no fault), can be tested for colorimetrically in sub-part-per- mi 11 ion concentrations (no guessing) and will recycle back to the mill from tailings (no cost).” Impossible? Based upon today's level of technology, such a product does not exist. However, a few of the qualifications listed above are certainly food for future thought. Meanwhile, progress is being made in upgrading three essential elements in this critical area of ore processing. They are: 1. Antiscalant reagent research and development. 2. On-line monitoring programs. 3. Reagent storage and feed systems. The objective of this paper is to out- line the current direction being taken in each of these areas and to present case histories as examples of how theory has been applied in field situations to better improve operations. LABORATORY SCREENING TESTS Recent technical papers have explained the various generic chemical raw materials which are available in the marketplace. While the merits of each chemical component are open to debate, the processes used by most major reagent suppliers to evaluate products in the laboratory are fairly standard. Common techniques incorporate both static and dynamic conditions in the search for the most cost effective product. Static Test Perhaps the most common test procedure used is based upon NACE Standard Test Method 03-74, which is "a laboratory screening test to determine the ability of scale inhibitors to prevent precipitation of calcium sulfate and calcium carbonate from solution." The objective of this test is to measure the change in calcium ion concentration in a container of saturated stock solution prepared from calcium chloride and sodium carbonate which is heated in a water bath. After 12 hours at constant temperature (160°), the mother liquor is pipetted into a beaker and a titrated for gm/l of unprecipitated calcium ion. A simultaneous test is performed on stock solution with antiscalant added. The results are then charted to determine the most effective antiscalant (with respect to preventing precipitation of calcite). It should be noted that this procedure examines only the ability of a chemical additive to retain calcite in a saturated solution where thermal stress is applied. This is commonly referred to as sequestration or stabilization. It has been documented that products which act in this manner (i.e., inorganic and organic phosphates) are good scale inhibitors. However, low molecular weight anionic polymers function in a much different manner by distorting calcite crystal size, shape and charge density, thus preventing scale formation. Because of this different mode of operation, static tests may not prove conclusive where polymers and sequestrants are being compared. The simplicity of this test makes it easily adaptable for field use, although modifications are often made.

Jan 1, 1986

By Nathaniel Arbiter

In attempting to assess the contributions of Antoine Gaudin to the profession which he illuminated for almost a half-century, we will need to examine a very broad canvas. He was active in three significant areas: as a teacher; in research, both through his own endeavors and those of his students; and as a consultant to the mining industry and to the Government. Beyond these specific contributions, there was the major personal influence he had on scores of students, friends, and colleagues in the profession. If a single measure of the man's contribution is to be found, it will be the extent and direction in which he influenced the practice of his profession. To find this we should examine the state of miner- al processing when he began his activities in the 1920's, the progress which has taken place over the past half-century, and the part his activities played in this advance. However, there is a provocative and broader examination which I have chosen to make instead. This is to examine the past century in mineral processing through the lives of three men who, by common agreement, stand on the heights, both in teaching and in their contributions to industry: Robert H. Richards, Arthur F. Taggart, and the man whose memory we honor this evening, Antoine M. Gaudin. Their careers, by coincidence, cover just a century. This is also AIME's first century, and the first century of mineral industry education in the United States. In fact, mineral processing itself on any significant scale in the country encompasses only a century and a quarter. BEGINNINGS OF PRACTICE IN THE U.S. Before the 1840qs, U.S. mining, except for coal and iron ore, was on a small scale and was confined to the eastern states, with processing practically nonexistent. The 1840's saw the beginning of Michigan native copper production, including ore dressing; the 18501s, iron ore production in Minnesota; and the 18601s, lead production and processing in Missouri. But the most explosive event was the California gold rush after 1848, which not only brought tens-of-thousands of fortune hunters to the West, but also catalyzed broad mining activities and processing within the following decades. This was not only in Calif-

Jan 1, 1976

By Rush H. Spedden

Antoine M. Gaudin was a vigorously creative man and throughout his career an internationally respected leader of his chosen profession of mineral engineering. To his professional colleagues and clients and to his former students he was both "Professor Gaudin," their wise, inspiring, and enthusiastic teacher, and "Tony," their warm and beloved personal friend. Thus, his teachings and his unique inquisitive-creative approach to problems live on and grow in the accomplishments of his students. Antoine Gaudin was born at the turn of the century in Smyrna, Turkey, where his father was general manager of a French-owned railroad. It was there that he spent his earliest years, literally in the shadow of classic marbles from diggings at the site of Aphrodesias, which his father had rediscovered. From this, Tony developed an appreciation of the arts. He eventually surrounded himself with art treasures; he reveled in the beauties of nature, and he cherished his choice collection of rhododendron and azaleas. His artistic traits led him to take up painting when his daughter, Elinor, sought his help in blending her tints for a water color. In typical fashion he was not satisfied until he had become adept with pastels in capturing the muted tones of distant landscapes and the technical properties of light and color. Unfortunately not many paintings were produced. His paternal grandfather was Marc-Antoine Gaudin, for many years secretary of the Academie des Sciences in Paris, and a well known chemist and mineralogist whose primary interests included the synthesis of precious stones. In an autobiographical sketch written in 1939, Dr. Gaudin recalled: "As a child I saw many of the original synthetic sapphires and rubies which my father had inherited. This, coupled with my father's avocation of mining ventures and archaeology, early decided that I would become connected with the mineral industry." One can speculate that the archeological activities of his father, the mineral systhesis experiments of his grandfather, and his own early studies of mineralogy and geology formed a base from which his special talents as an experimentalist were to develop. Laboratory research under Professor Gaudin's personal guidance was often an intensive, fast- moving, and exciting experience--especially to a new graduate student. First of all, Professor Gaudin was a highly skilled observer with seem-

Jan 1, 1976

By C. A. F. Pinto

In the present work compared flotation kinetics of apatite with four different collectors was established. Sodium oleate and rice bra~ oil were used to represent conventional collectors. The new collectors included a sulfosuccinate and a sulfosuccinamate. It was observed that the collection ability of each reagent was very dependent upon the mineral size ranges. The results-were analyzed in terms of size-by-size recovery curves. Flotation rates were also very dependent on size ranges of the mineral particles. One of the new collectors displayed higher flotation rates for coarser particles than the other reagents tested. Synergetic effects were also apparent when a conventional collector was mixed to a new collector.

Jan 1, 1991

By Kerry Spickelmier

Editor's note: information for this feature was taken from the published APCOM proceedings. Computer trends, with special focus on the reasons for computer use, grabbed the lion's share of attention at the 23rd worldwide meeting on the Application of Computers and Operations Research in the Mineral Industry (APCOM 23). However, technical topics did not provide the meeting's sole focus. The last-minute inability of certain former communist countries to fund the travels of a few scheduled speakers was a reminder that science does not operate in a void. As with all technical progress, the APCOM presentations raised interesting questions regarding interrelated organizational dynamics and political and socioeconomic issues. Consider US Bureau of Mines (USBM) research to design an expert control systems to "duplicate" an experienced, "good" operator during automated underground roof bolting. In his presentation of the project, Takach, Jr. stressed the importance of preserving the ability to switch from automatic to manual drilling control. From a technical standpoint, this allows the expert system to "learn" from a good operator. As important, he said, is that this flexibility decreases the human operator's sense of being replaced by the machine. The question arises: Which will loom larger in union minds, increased operator safety through remote opera¬tion or the potential for total operator replacement? Like any new product, computer technology relies on marketing to aid its acceptance and use. Consider, too, a decision support system, by Schena and Gochin, for mineral resource management in a developing country. The authors said "the analysis permits the assessment of the overall socioeconomic consequences of mineral prospects and allows incorpo-

Jan 1, 1992

By Alfred Weiss

At the end of the first decade of digital computing in the minerals industry, geostatistics in North America was still in its infancy. This was in contrast with the rest of the world where the technique of kriging was already widely practiced. By the end of the 1970s, there was increasing awareness among practitioners of its potential. But it was not until the late 1980s that geostatistics was universally applied and accepted. This was due, in large measure, to contributors at Applications of Computers and Operations Research in the Minerals Industry (APCOM) symposia. Such an evolution in new computer methods could again be observed at APCOM 26.

Jan 1, 1996

The 26th international APCOM symposium, hosted by The Pennsylvania State University, was held Sept. 16 to 20, 1996 in University Park, PA. Conducted about every 18 months throughout the world, APCOM symposia focus on the Application of Computers and Operations Research in the Mineral Industry. The APCOM International Council is the governing body of the symposia and determines the symposium’s locations and sponsorships. This group is composed of the nine permanent (voting) members. They include the University of Arizona, Colorado School of Mines, Pennsylvania State University, Society for Mining, Metallurgy and Exploration, Inc., Canadian Institute of Mining, Metallurgy and Petroleum, South African Institute of Mining and Metallurgy, Technical University of Berlin, Institution of Mining and Metallurgy and Australasian Institute of Mining and Metallurgy. The three nonvoting members are Moscow Mining Institute, China Institute of Mining and Rudarski Mining Institute of Slovenia.

Jan 1, 1996

By Raymond E. Riethmann

El clasificador de espiral fue diseñado originalmente para circuitos cerrados de molienda. Desde entonces se ha aplicado con éxito a otros trabajos de clasificaci6n donde se necesita realizar un corte de dos productos. Inherentemente a las cualidades especiales de este cla- sificador está especialmente preparado para: clasificar, lavar, o agotar materiales tales como minerales, roca fosfática, arenas, carbbn, conchas de ostra y sales fosfáticas. Presentamos ahora las características de operation, flexibilidad de diseiio y líneas maestras para una apropiada aplicación.

Jan 1, 1982

By David M. Jurich, Randy J. Essex, Alex de Aboitiz

An Automated People Mover (APM) transit system is planned for the growing Phoenix Sky Harbor International Airport. The APM will improve passenger movements between the terminals, and provide a link to parking facilities, a new rental car facility, and the planned metro Light Rail. The underground works will include shallow twin bored tunnels, taxiway crossings, and underground stations constructed beneath critical airport facilities. Challenging soft ground conditions will require extensive underpinning and ground improvements. Design is underway, and construction is scheduled to begin in 2007 with project completion in 2015. The owner’s planned delivery method for the APM Project will be Construction Manager at Risk (CMAR) with a Guaranteed Maximum Price.

Jan 1, 2005

By Jim Truman

Appalachian coal mines include operations in eastern Kentucky, Maryland, Pennsylvania, Virginia and West Virginia. During 1994, they produced a total of about 342.5 Mt (377.6 million st) of bituminous coal. This figure represents 37% of the total production from the United States. This region contains nearly all of the nation's coking coal reserves and high-quality compliance steam coal that will be in demand after the turn of the century as utilities comply with phase two of the 1990 Clean Air Act Amendment. Figure 1 shows the location of the study area and the general regions that supply various coal types. Data for the study reviewed here were compiled and interpreted from Mine Safety and Health Administration (MSHA) production reports, Federal Energy Regulatory Commission 423 reports, King's Export database and additional data from the US Department of Energy's (DOE) Energy Information Administration (EIA). Table I is an overview of the total production from Appalachia and the delivered tonnage to various sales categories.

Jan 1, 1995

By Barbara Fotta

This article examines health and safety trends during the past 10 years at Appalachian surface and underground bituminous coal mines. Data for Appalachia include Pennsylvania, West Virginia, Virginia and eastern Kentucky. These states account for more than 90% of the coal production in the Appalachian region. (Production, accidents and fatalities in Ohio, Maryland, Tennessee and Alabama are not included in computing Appalachian trends.) Trends for Appalachian underground mines are differentiated by size and mining method into three categories: - Small mines with fewer than 50 employees. - Large nonlongwall mines with 50 or more employees. - Longwall mines (mines with at least one longwall production face).

Jan 1, 1995

By Suresh K. Bhatt

Appalachian coalfields have been the predominant source of quality coals since the inception of commercial mining in the United States. In a broad sense, Appalachian coalfields can be considered those east of the Mississippi River, representing about 55% of total US coal production. In this special feature on Appalachia in MINING ENGINEERING, emphasis is given to the four coal-producing states of Pennsylvania, West Virginia, Virginia and (eastern) Kentucky. These four states produce more than 90% of the coal from the total Appalachian region, or about 40% of the total US coal production. Historically, Appalachia has been the principal source of coal for domestic industries and for export. There have been numerous fluctuations in the Appalachian coal industry during the past 20 years. Appalachia was affected by cyclical and structural changes in various industries, particularly the US steel industry, and changing world coal markets. It was also the region of more mine worker labor stoppages than other parts of the country. In general, the factors that affected Appalachian coal production over time are identical to those that determined changes in coal production nationally.

Jan 1, 1995

By James R. Craig

The Central and Southern Appalachians were the major sources of gold in the United States throughout the first half of the 19th century and have continued to yield gold to the present day. Small amounts of gold were probably extracted by the Indians and the Spaniards but the first documented report of gold in the region was made by Thomas Jefferson who found a four pound lump of gold ore, which yielded 0.85 troy oz., in the Rappahannock River of Virginia in 1782. Gold was subsequently discovered in North Carolina between 1793 and 1799, in Virginia in 1806, in South Carolina in 1827, in Georgia in 1829 and in Alabama about 1830 (Becker, 1894-5; Pardee and Park, 1948). The gold belts of the Central and Southern Appalachian Piedmont and Blue Ridge Provinces are shown in Figure 1. The superimposed circles indicate the mount of production from some of the more productive and well known areas. Although North Carolina produced far more gold than the other states, the most significant concentrated area of production is the Dahlonega District in Georgia which yielded more than 500,000 troy ounces. After discovery, gold production increased rapidly as shown in Figure 2. Production was at its maximum between 1830 and 1852 with combined totals generally exceeding 30,000 troy ounces per year. Production dropped sharply after the California gold rush in 1849 as experienced miners moved westward in search of bigger and easier stakes. After the Civil War briefly halted gold mining in the Appalachians, production rose to an average of about 8,000 ounces per year from 1865 until 1878 and to an average of about 13,000 ounces per year from 1881 until 1915 when it again fell to near nil (Pardee and Park, 1948). Minor resurgences occurred in the 1930's and 1940's. Although there has been no reported production in recent years, it is likely that "weekend panners" still remove hundreds of ounces from streams annually. The total reported production for the area through 1959 is in excess of 2.5 million troy ounces.

Jan 1, 1981

By Henry A. Signore

The Appalachian coalfield, located in eastern Kentucky, Pennsylvania, Virginia and West Virginia, has been one of the most productive in the United States. Total production from the Appalachian coalfield during 1994 was 340.8 Mt (375.4 million st), or 37% of the 929 Mt (1 billion st) produced in the United States that year. This region contains various coal types from high- to mid-sulfur coal in Pennsylvania and northern West Virginia to low-sulfur, compliance steam coal and premium-grade metallurgical coal in eastern Kentucky, Virginia and southern West Virginia. The region's product is in high demand in domestic and export markets. Productivity continues to improve, resulting in the primary coal operators solidifying their market positions.

Jan 1, 1995

By Lit-Mian Chan, David H. Carlson, John H. Johnson

This paper presents an apparatus and procedures to implement a methodology for controlling ambient air quality in a confined working environment, such as an underground mine, an underground storage area, or a tunnel. The air quality control methodology is directed at limiting the quantities of exhaust pollutants emitted by diesel-powered vehicles into the confined space by identifying vehicles that are excessive polluters. The methodology is based on tailpipe and ambient air measurements in the confined space, and the ambient air threshold limit values (TLVs) for the various diesel exhaust pollutants. The methodology consists of two computational methods; a deterioration criteria computational method to identify excessive polluting vehicles, and an engine performance computational method to determine engine performance and to provide information needed to diagnose engine faults. The methodology is designed for implementation in conjunction with a preventive maintenance program. The first part of the paper describes the mine air and tailpipe emissions measurement apparatus and techniques used to obtain data. This is followed by sections discussing the deterioration criteria and the engine performance computational methods. A section discussing some common engine emissions-related faults is also presented. Lastly, a proposed procedure to implement the methodology including a possible hierarchical structure for mine personnel involved to implement the procedures is presented.

Jan 1, 1993

By J. B. Gwiazda

In designing mine workings and adequate roof supports, it is indispensable to determine properties of the strata surrounding the workings. The proper selection of roof supports is based, before everything else, on a thorough knowledge of the roof rock strength, especially tensile strength. This parameter is a vital factor in the delamination of roof rocks and eventual cave-in. It is also important to know the properties of the floor on which the roof supports are set. While driving galleries, it is essential to know beforehand the strength of rocks that will be encountered in the near future during the work. The devices described will help to obtain this information.

Jan 1, 1987