Search Documents

By O. Olajide, E. H. Cho

A laboratory study of the jigging process with Pittsburgh seam coal has been conducted. The laboratory-scale Baum jig used in this study was a McNally-Norton LO30X Right Hand Model Baum jig with an effective screen area of 0.186 m2 Feed material was prepared by selecting a size range from 6 mesh to 1.91 cm. Solid feed rates were 27.2 kg/min and 32.7 kg/min. Water flow rates were varied from 37.9 to 94.6 L/min. It has been found that smaller particles give higher values of density of separation and lower efficiency of separation. Increasing water flow rate increases the discharge rate of clean coal at a constant solid feed rate. It appears that the efficiency of separation increases by increasing water flow rate up to a certain value, and then levels off upon increasing the flow rate further.

Jan 1, 1988

By Langtry E. Lynd

Ilmenite concentrates prepared from beach and dune sands of Florida, India, Australia, and other localities deviate to varying degrees from the theoretical composition of pure ilmenite, and generally contain more Ti02 than the formula FeTiO3 would indicate, and some Fe203. This variation in composition is due to different amounts of altered ilmenite in the concentrates.(l) The alteration has been shown to take place by oxidation and leaching of the iron in ilmenite, to yield residual products consisting of amorphous or very finely crystalline titanium dioxide and ferric oxide, Other studies (2) have stressed that ilmenite may alter first to an amorphous titanium-iron oxide, or to an amorphous mixture of titanium and iron oxides, with later alteration to crystalline titanium dioxide. There has been some speculation as to whether alteration of ilmenite is usually caused by weathering or by hydrothermal processes,(3, 4, 5) Three main methods of approach were used to study the mechanism and rate of ilmenite weathering, (1) Etch tests were used to learn the relationship between crystallographic orientation and the rate of chemical attack on ilmenite. (2) Altered ilmenites in New Jersey sands were compared with ilmenite in rocks of the area from which the sands were probably derived, (3) Experiments were carried out to determine at what rate, and by what agents, originally fresh ilmenite could be altered in the laboratory under simulated weathering conditions.

Jan 1, 1959

By E. D. Gálvez, L. A. Cisternas, A. López-Valdivieso, F. Lucay

"The floatability of molybdenite fines in saline solutions was investigated through microflotation studies using a modified Hallimond tube. In addition, the effect of pH and gypsum precipitation from calcium ions (Ca2+) and sulfate ions (SO4 2-) ions in saline water on the recovery of the molybdenite was analyzed. It was found that the floatability of molybdenite fines significantly increased with the ionic strength of the saline solutions and is independent of pH above 0.5 mol/L ionic strength. The high floatability of molybdenite in saline solutions is explained as being due to the low electrostatic repulsion between bubbles and the edges of molybdenite particles, which is exceeded by interactions due to van der Waals and hydrophobic forces. The precipitation of Ca2+ and SO4 2- ions as gypsum had a detrimental effect on the natural floatability of molybdenite because of gypsum crystal attachment on the faces of the molybdenite particles. This precipitation phenomenon may be initiated in copper–molybdenite flotation circuits that use recycled saline water, like seawater containing Ca2+ and SO4 2- ions.IntroductionWater availability is a significant factor in mining projects. Water, particularly fresh water from rivers and underground water, is becoming a scarce resource for mining operations and new projects. Under these circumstances, the use of water with high concentration of salts in flotation plants is becoming increasingly important (Cisternas and Moreno, 2014). The use of seawater has been studied as a sustainable solution for many mining companies in dry areas located near the sea. Notably, using seawater in mining operations is how mining companies in Chile have coped with the problem of water resources (Cisternas and Gálvez, 2014). In 1930, small plants in Chile used seawater to float chalcopyrite from high-copper-grade ores. In 1975, the results of tests in pilot plants for the flotation of copper minerals with seawater were reported. It was found that froth formation in seawater at pH 9.5 was suitable to make the rougher circuit work properly, even without frothers. The Cenizas mining group successfully floated chalcocite, bornite and chalcopyrite in the Las Luces plant in Taltal in Chile using seawater (Moreno et al., 2011). Minera Centinela (Antofagasta Minerals S.A. Chile) is currently processing porphyry copper ores using a seawater mixture consisting of 20 percent fresh seawater and 80 percent recycled water. Lower consumption of flotation reagents was reported in both seawater and salt water. In addition, studies performed with synthetic seawater showed that certain frothers increase the froth volume, whereas others decrease it. Additionally, the froth produced with seawater carries a high amount of gangue, and low-quality concentrates are obtained, requiring more cleaning stages."

Jan 1, 2015

By S. Acar, P. Somasundaran

Results of selective flocculation of natural ores containing two or more minerals and of synthetic mineral mixtures do not usually agree with what is expected on the basis of the results from single mineral tests (Acar and Somasundaran, 1985). This is mainly due to the ionic species released by the minerals, which act differently under different pH values. The objective of this investigation was to study 1) the surface chemical composition of selected sulfide minerals-natural chalcopyrite and pentlandite and synthetic covellite, millerite, and pyrrhotite-and 2) the changes brought about by the dissolved mineral species. Electron Spectroscopy for Chemical Analysis (ESCA) was used to perform the surface analyses.

Jan 1, 1991

The Carlin Trend is North America's premier gold producing district. It is located in northeastern Nevada's Elko and Eureka Counties along a northwest trending belt about 65 km (40 miles) long and 8 km (5 miles) wide (Thorstad, 1989; Jones, 1989). This trend is the worldwide reference site for epithermal, sedimentary rock-hosted microscopic gold deposits. At least 19 deposits have been discovered to date, varying in size from 933 kg to 1.08 kt (30,000 to 35 million contained oz) of gold (Fig. 1). Newmont Gold Co. and its parent, Newmont Mining Corp., jointly constitute the largest mineral right holders in the district. They own or control more than 1000 km'- (386 sq miles) in and around the Carlin Trend and own all or part of 16 out of the 19 mines and prospects identified to date. Since the initiation of Newmont's exploration activities in the Carlin Trend in 1961, 2.24 kt (72 million oz) of cumulative gold resources have been identified. Cumulative production from all mines since the start-up of Newmont's Carlin mine in 1965 to the end of 1989 was about 202 t (6.5 million oz) (Jones, 1989). The incentive of sustained high gold prices and innovation in processing technology resulted in a significant acceleration of gold output over the last few years. Newmont Gold alone produced more than 43.5 t (1.4 million oz) in 1989. That is equal to 22% of the cumulative 1965 to 1988 output, and an almost 200% increase over its 1986 output.

Jan 1, 1991

By Liaqat Ali Shah, Muhammad Farooq, Zait Ullah Shah, Francisco Rolando Valenzuela-Díaz

Bentonite collected from Nowshera (Pakistan) was treated with NaCl, and the < 2-μm clay fractions were separated by sedimentation process. The textural changes in NaCl treated purified bentonite were compared with raw and physically purified sample. It was detected that the NaCl-treated purified bentonite and the sample purified by simple sedimentation, respectively, consist of sodium-montmorillonite and calcium-montmorillonite as a major clay mineral. The honeycombed-type morphology was observed for both the purified samples; however, the particles of NaCl treated purified bentonite were relatively in a compact form. The particle sizes of both the purified samples were found considerably smaller. The high volume percent of the fine particles was noticed in the NaCl-treated purified bentonite. This attributed that the sodium exchange has a valuable impact on the bentonite dispersion in aqueous media during particle size measurement. The relatively high mesopore area/volume and micropore area/volume and specific surface area (SSA) were detected in purified samples. The NaCl-treated purified sample showed relatively high mesopores area/volume than the sample obtained by simple sedimentation. These changes seem to be originated from either high montmorillonite contents and/or the smaller particle size, which might be produced after the layer rearrangement during the interlayer cation replacement by Na+ ions. The large SSA and high porosity of purified samples particularly the NaCl-treated bentonite suggest their potential use as adsorbents, catalysts, pharmaceuticals, and cosmetics.

Jan 7, 2021

By J. Keng, S. T. Chen, T. M. Shih

Kwanyin Tunnel is presently the longest (7.7 km) railway tunnel in Taiwan. Due to heavy railway traffic, a pass-by station will be built inside the tunnel to increase the traffic flow. Since the concentration of toxic gases released by the locomotives may reach dangerous levels, a research program was conducted for the purpose of designing a ventilation system which could dilute and/or remove the toxic gases to maintain an acceptable pollutant level. The program consisted of two parts. The first part was field measurement during which the concentrations of pollutants and wind velocities were measured at various points inside the tunnel to acquire basic data regarding ambient air quality, piston effects for the different types of trains, and existing ventilation conditions. Weather data (temperature, humidity, atmospheric pressure, wind direction and velocity) were gathered at many stations, both on the surface and inside the tunnel. The amount of pollutants released by each type of locomotive for various conditions were also measured. The second part of this study involved establishing mathematical models for predicting the air quality of the various proposed ventilation systems. Three different models were used for this work. The first one is a piston effect model which assumes that the gases and air undergo immediate mixing inside the tunnel. The second one is also a piston effect model which assumes that the diffusion ability of the gases is zero. The third one is a conventional ventilation model which was used for natural and mechanical ventilation conditions. From the result of field measurement and mathematical model studies, a ventilation system was chosen with consideration of both ventilation effects and construction costs.

Jan 1, 1987

On longwall coal faces in some Japanese coal mines more than half of the air coming from the intake gate road flows into the caved goaf and the air heated by the hot waste rocks in the goaf comes out through the latter half of the face. This still constitutes a major heat problem in spite of the introduction of gate and face air coolers. Therefore, in order to establish effective measures to improve the environ- mental conditions, it is essential to obtain information pertaining to the air flow pattern on the face as affected by the goaf conditions and the air flow regulating measures taken at the intake side of the face. Experiments for this purpose were carried out using a coal face model. The model was reduced to a scale of 1110th of the real face measuring 100 m long and 2.2 m high, equipped with self-advancing supports. The model design was also conceived to accomodate eventual modifications of the space of the caved goaf as imposed by the actual conditions.

Jan 1, 1980

By Alessandro Boscaro, Daniele Martinelli, Cristina Gabriela Oñate Salazar, Daniele Peila, Carmine Todaro

"The wear phenomenon in TBM machines is not a simple issue, as many parameters are playing an important role on the consumption of the tools during a tunnel excavation. The action of the wear due to the contact with the soil can occur on the excavation tools, on the cutterhead, in the excavating chamber and on the screw conveyor. The test developed at the Laboratory “Tunnelling and Underground Space Center” of the Politecnico di Torino is aimed to reproduce the interaction between the tools and the excavated material, simulating the excavation conditions in terms of soil conditioning and water content. The test, which is not standardized, is studied to evaluate the wear in a global point of view. The present work starts by testing the influence of the use of chemical agents during the conditioning phase on the drop of the wear phenomenon, in terms of metal weight loss. 1. INTRODUCTION The wear phenomenon of the excavation tools used in TBM tunneling machines is playing recently a major role in the design stage of full-section tunnels in both soils and rocks. Concerning EPB excavation technology, the main issue regarding productivity is the wear of its components (Peila et al.,2012), which increases the so called dead time in the whole process. The friction generated between the components and the ground causes the consumption of the tools and other metallic components in contact with the ground, described as primary and secondary wear by Nielsen et al. (2006a). This leads to downtime, with risky and complicated maintenance operations (Peila and Schulkins, 2009), as occurred in recent tunneling works in Liguria (Italy). The study of this argument in granular soils is very delicate, as it encloses not only the properties of the excavation tools, but also the characteristics of the ground to be excavated (hardness, mineralogy composition, shape and dimension of the particles and moisture content). The penetration mechanism is based on the scraping of the ground, by mean of cutting tools, with its consequent consumption. Concerning the rocks, the excavation principle is characterized by crushing the rock mass matrix by applying high compressive stresses through cutting disks. In such a way, to avoid frequent downtimes and their consequent economic losses, it is very important to study this subject and therefore understand and forecast the durability of the components, in order to try to maximize the productivity of the machine by reducing the frequency of maintenance stoppings."

Jan 1, 2016

By K. Biswas, S. S. Peng

The stability of pillars in old mined-out districts is greatly dependent on the weathering action caused by moisture penetration into the pillar structure. Field observations in old mining districts indicated that this weathering action becomes critical in terms of the stability of the pillar if the coal seam contains parting or binder (layers of claystone or mudstone). The weathering action caused by moisture penetration over a long period of time degrades both parting and coal. However, it has been observed that the structural deterioration is more severe in parting. Moisture-penetration rates in parting and coal are different. The extent of the weathered zone in various layers of the pillar is primarily time dependent. This paper investigates, both in the laboratory and in the field, the effects of weathering action on coal and parting. In the laboratory, slake durability indices and uniaxial compressive strength tests for dry and saturated specimens are compared for coal. In the field, the in situ strength profiles for coal and parting layers are obtained, and the effect of time (in terms of the pillar age) on the strength profiles is studied An attempt was also made to establish formulae for time-dependent strengths of coal and parting.

Jan 1, 2000

By K. Biswas

For the pillars, which have been standing long after mining, the stability depends much on the weathering action in the presence of mine moisture. From the field observations, it has been found that this weathering action becomes critical in terms of pillar stability if the coal seam contains partings or binders in it. The weathering action degrades both the partings and coal in terms of their load bearing capacity as the mine moisture penetrates into them. This paper investigates the effect of weathering action on coal and partings in the laboratory. In the field, the strength profile in the coal and the partings and the effect of time (in terms of the pillar age) on them have been studied by using borehole penetrometer. In this paper, an attempt has also been made to establish formulae for time dependent strength of coal and partings.

Jan 1, 1997

By S. D. Thompson, J. C. Dzurino

This investigation mainly focused on designing a bunker system for a large underground coal mine. The primary purpose of this bunker system was to keep high- and low-sulfur coal segregated on the underground belt system. These bunkers were also required for protecting the mine faces from out by belt delays. Methodologies used in developing this plan are briefly discussed. The final design and the procedures formulated for implementing it are also presented.

Jan 1, 1987

By Liang Ruilu, Guo Lihua

In light of the properties on process mineralogy of the old tailings in a certain copper mine in the People&apos;s Republic of China, a new process of combined reagent and stepwise flotation is applied in which the flotation of copper sulfides is followed by the flotation of copper oxides. Recoveries of copper and associated gold and silver have been greatly increased. The tailings obtained were subjected to the gravitational separation-magnetic separation process to recover iron minerals. Tailings from iron separation are taken as fillers and sent to the pit underground. Thus, the secondary resources are comprehensively utilized.

Jan 1, 1995

By N. Dashbold, E. Rudnik

"Waste electric and electronic equipment currently comprises the fastest-growing waste stream in the world, but at the same time it is seen as an important source of metals for the recycling industry. E-waste is usually treated pyrometallurgically, with hydrometallurgical methods used to a lesser extent. This paper reports the results of research on the selective recovery of copper from smelted low-value electronic waste. Pyrometallurgical pretreatment of the scrap allowed the removal of plastics and the increase of metal content in the material. The obtained alloy of copper, zinc, tin and silver was a multiphase solid consisting of two brass phases and inclusions rich in iron, lead and silver. Copper alloy was further anodically dissolved in ammoniacal chloride solution. It resulted in high degradation of the material and accumulation of the metals mainly in the slime. The slime was then leached in acid or ammoniacal chloride and sulfate solutions followed by selective copper electrowinning. Hydrochloric acid was the most efficient solvent for the slime, but ammoniacal solutions were more selective for copper. Copper could be leached with 96 to 100 percent and 87 percent efficiency from the slime by the chloride and sulfate solutions, respectively. Copper with 90 to 99 percent purity at current efficiency of 42 to 76 percent was obtained from the acid solutions, while copper with 98 to 99 percent purity at current efficiency of 60 to 86 percent was deposited from the ammoniacal baths. IntroductionObsolete electrical and electronic equipment makes up the fastest-growing waste stream in the world (Baldé et al., 2015), due not only to the introduction of wider ranges of new types and models of a variety of electronic products but also to the shortening of their life-spans, sometimes referred to as planned obsolescence by producers (Keeble, 2013). About 42 million tons of electronic waste, or e-waste, are estimated to have been generated globally in 2014 (Baldé et al., 2015), and it is expected that in the European Union alone the waste electrical and electronic equipment (WEEE) stream will reach more than 12 million tons by 2020 (European Commission, 2015). Accurate evaluation of e-waste generation (Wang et al., 2013) and its global transport (Breivik et al., 2014) is difficult, mainly due to a lack of high-quality data related to its market and socio-economic dynamics.Many countries introduced legislation to control e-waste flow, collection and recycling. For example, Directive 2012/19/EU on waste electrical and electronic equipment (European Parliament and the Council of the European Union, 2012) obliges all E.U. members from 2016 to maintain a minimum collection rate of 45 percent of the total weight of WEEE collected. From 2019, the minimum collection rate to be achieved annually shall be 65 percent of the average weight of electronics placed on the domestic market in the three preceding years, or alternatively 85 percent of WEEE generated in the territory of the particular member."

Jan 1, 2017

By Y. Luo

"It is generally known that spontaneous combustion potential is a function of coal rank, with low-rank coals having high susceptibility to self-ignition and high-rank coals having low potential. To establish this functional relationship and use it as an engineering tool to identify the propensity of coal to self-heat, both rank and spontaneous combustion potential should be quantified. ASTM D388 is normally used to classify coals by rank, but this classification system can only serve a qualitative analysis. To classify coals by their potential for spontaneous combustion, the self-heating temperature (SHT) method originally developed by the U.S. Bureau of Mines (USBM) was used by Litton and Page (1994) to correlate coal rank with spontaneous combustion potential. In that method, the SHTs of coal determined by an adiabatic experiment are linked with proximate analysis results through a proposed concept known as the “moist fuel ratio.” This ratio is a function of moisture, volatile matter and fixed carbon, all of which have widely different content percentages in different ranks of coal and have strong relationships with coal rank. However, the method is highly empirical, and there is large standard deviation between experimental data and calculated results. The equation correlating the coal quality parameters to determine SHT should be improved with more experimental data.This paper reports on the development of a new system for predicting the spontaneous combustion potential of U.S. coals, based on coal composition data from the U.S. Geological Survey’s coal quality database. First, the user is provided with a quantified classification of coal rank. Second, based on experimental SHT data covering a wide range of ranks from lignite to low-volatile bituminous coal, the original USBM correlation for predicting SHT is improved for the respective rank of coal. The relationship between the rank and SHT of U.S. coals was developed and plotted. The plot diagram can be used for a quick estimate of the SHT of a U.S. coal and as a cost-effective tool for the initial risk assessment of a new mine development."

Jan 1, 2015

By J. Chai, Y. Qiang, D. D. Zhang

"In order to control Quaternary loose layer settlement in East China, there are monitoring results based on the 3 water level observation holes and 7 sand layer of fiber Bragg grating (FBG) strain sensor. Un-der the conditions of upper group water injecting to lower group of loose layer, the deformation characteristics of upper, middle and lower group of loose sandy soil layer changing with time and relationship with the water level are studied. The constitutive relation of stress-strain is also studied at different sand layers. Research results show that using water injecting from upper group into lower group of loose layer can ease the loose layer compression deformation. With the water level dropped, in East China soil creep deformation occurred, which accord with viscoelasto plastic model. The deformation of lower sand group has clear later effect and no direct relationship with water level. The results provide an important basis for the study East China stratum settlement model and water management. INTRODUCTION Ground-surface subsidence is a common geological disaster, which has the features of continuous, changing slowly, concealment (Y.P. Yin et al. 2005). Today, due to underground mining and constructions in formation compression, surface subsidence is wide-spread in the world, which is the environmental geological problems in the worldwide that cannot be ignored (Y.Q. Xu et al. 2006, D.L Gallo-way et al. 2000, Qiu, B. et al. 2011). The eastern region of China has generally geological disasters in coal mine geological caused by the thick loose layer settlement like as mine shaft failure. Stratum dehydration consolidation is a major cause of loose layer settlement (H.Y .Liu et al. 2007). A method of water injection using ground water to stable water level is proposed, which can effectively control the loose layer caused by compression settlement(J. Chai et al. 2012&.2013). Accurately knowledge the characteristics of strata deformation is the premise of settlement management (Q.C. He et al. 2006). Previous re-search (J.F. Miu et al. 1996, X.Y. Gu et al.1998, Y. Zhang et al. 2006), mainly studies are focused condition of the city pumping irrigation, de-formation characteristics of middle and up loose layers. On a group of aquifer in East China, the loose layer losing water is caused by coal mining, bottom water drainage and overlying strata water flowing fractured zone hydrophobic induced by mining, which the dehydration conditions have great difference from one to another. The Position of water loss is centralized in bottom aquifer, and the formers of ground subsidence geological environment and settlement mechanism are different. According to the study of stratum settlement, usually the de-formation of sand layer is ignored(C.H. Liu et al. 2004), but few studies show that the sand layer have the plastic deformation, and contains the creep deformation, water content of sand soil may become the main settlement layer (Z.X. Wei, 2002, C.H. Liu et al. 2004)."

Jan 1, 2015

By C. L. Peng, F. F. Min, S. X. Song

"Using a parameter representing the degree of hydration of particles in a liquid called hydration index I, which we derived based on Einstein’s viscosity equation, we evaluated the degree of hydration of fine montmorillonite particles in different aqueous solutions by measuring the viscosities of the montmorillonite dispersions and plotting relative viscosity against volume fraction of dry montmorillonite particles in the dispersions. We investigated the effects on the hydration of montmorillonite in aqueous solutions of (1) the type and (2) the concentration of electrolytes in the solutions and (3) pH. For the same concentration of electrolytes, the hydration index I of montmorillonite was found to increase in the order of Na+ > K+ for monovalent cations and Mg2+ > Ca2+ for divalent cations, and to decrease with increasing valence of cations in the order of Na+ > Ca2+ > Al3+. For both Na+ and Ca2+, the hydration index I first increased with increasing concentration of electrolytes and then decreased after a certain concentration. The hydration index I increased with increasing pH. IntroductionClay minerals have the distinctive ability to adsorb water molecules and hydrated cations in aqueous solutions, resulting in hydration on their outer surfaces and in their interlayer spaces. Many investigators (Jurinak, 1963; Anderson and Tice, 1971; Costanzo et al., 1982; Israelachvili, 1992) had found evidence of ice-like structures of water on clay minerals.This phenomenon of hydration plays an important role in the dispersion and sedimentation of clay minerals in aqueous solutions. To understand clay hydration, numerous experimental and simulation studies have been carried out since 1933, including the recent ones of Hawkins and Egelstaff (1980), Skipper et al. (1995), Karaborni et al. (1996), Salles et al. (2013) and Morrow et al. (2013). Among the factors that can influence a clay mineral’s hydration characteristics are chemical composition, type and degree of isomorphous replacement in its structure, and number and nature of associated exchangeable cations."

Jan 1, 2015

By D. He

In China, the total reserves of vanadium, reported as V2O5, in stone coal is 118 Mt (130 million st). Recovering vanadium from such a large resource is very important to China?s vanadium industry. The technology now being used to recover vanadium from stone coal has the following two problems in the leaching process: a low recovery of vanadium and high acid consumption. To resolve these problems, a new leaching technology is proposed. The effects of factors such as H2SO4 concentration, liquid-solid ratio, temperature and time, and the types and additions of additives were studied. By adding 1.5% (by weight) CaF2 and leaching the roasted residue of stone coal with 5.4% (by weight) sulfuric acid at 90°C for 12 hours at a liquid-solid ratio of 2 mL/g, the leaching degree of vanadium reached 83.10%. This proposed leaching technology gives a feasible alternative for the processing of roasting residue of stone coal and can be applied in the comprehensive utilization of stone coal ores in China.

Jan 1, 2008

By Xinming Chen, Huazhe Jiao, Qi Zhang, Yunfei Wang, Liuhua Yang

The effect of initial damage generated by weakly cemented interlayer surfaces on the physico-mechanical properties of layered cemented tailings backfill (LCTB) is considered for the interlayer inclination structure generated by multiple layered backfills in large-scale mining voids. Utilizing the theory of damage mechanics, the damage evolution and constitutive model of LCTB with interlayer inclination is constructed by considering the coupling of interlayer inclination effect and loading. Based on Mitchell’s mechanical model, we analyze the damage mechanism of the inclined cementation surface of LCTB, and derive the expression for the strength of LCTB considering interlayer inclination. The mechanical properties test of LCTB with different inclinations was carried out, and the results showed that the damage model of LCTB established was highly consistent with the experimental curves, which verified the correctness of the model. The initial inclination damage leads to the decrease of adhesive cohesion of cemented surface, and with the increase of inclination, the separation of layered surface, aggravation of misalignment, layered cemented surface is more prone to shear damage, and the mechanical properties of cemented tailings backfill in the lower part of layered surface are not effectively played, which reduces the overall performance of the material.

Nov 23, 2023

By K. Getsos

Western Greece is a favorable site for exploration and discovery of oil fields. The most important potential source rocks seem to be all the rocks deposited before middle Jurassic under special circumstances, such as reducing conditions, which allowed preservation and maturation of the organic material. In general all the rocks of middle Jurassic to Paleogene are not favorite source rocks. The porosity type was studied on fifty samples using scanning electron microscopy (SEM). Potential reservoir rocks are the porous Paleogene wackestones-packstones with boring, channel and vuggy porosity type. Finally seal rocks are the impermeable mud-stones and wackestones of Jurassic, Cretaceous and Paleogene age. These rocks consist of micrite and whole sells of foraminiferas and the porosity type is mainly intercrystal/interparticle. A Total Organic Carbon (TOC) analysis, conducted on seventy samples using a wet oxidation method, has revealed an extremely low TOC content (less than 0.05 %). This amount is by far less than the minimum organic content amount, required for source rock characterization and characterizes all the rocks of middle Jurassic to Paleogene age. Additionally, 18O and 13C stable isotope analysis was contacted and the results are given in d values. All the rocks within the studied time interval have much lower d values than petroleum source rocks. Clay mineral content was studied in almost seventy samples. As is indicated by the clay mineral content the studied rocks have reached up to the Middle Diagenesis and the temperature during diagenesis was rather low.

Jan 1, 2006