Search Documents

By J. L. Vanderbeek

Investigations have been conducted at Chino Mines Company into the effect that SAG mill recycle material (critical size) exerts on SAG mill throughput and specific energy requirements. Tests were conducted on the laboratory, pilot, and plant scales, to evaluate the merits of alternative treatment options. Removing critical size material from the SAG mill circuit has been shown to improve new feed rates by 34% with a reduction in specific energy (kWh/ton) of 33%. Test results obtained to date are presented.

Jan 1, 1985

By H. E. Goetzman

A cooperative research project supported by the taconite industry and the Minnesota DNR was undertaken to establish quality standards for carboxymethyl cellulose (CMC) based organic binders. The objective of this study was to identify the effect of CMC quality parameters such as degree of substitution, molecular weight, and purity as well as the effect of inorganic extenders such as sodium carbonate on performance. These factors have been evaluated by green-ball testing with two taconite concentrates followed by pot-grate tests. Balling tests with bentonite and Peridur were conducted to provide baseline data. At a constant DS the molecular weight as measured by viscosity had the greatest effect on green-ball drop strength. Dry-ball compression strength was most dependent on CMC addition rate and sodium carbonate content. DS was not found to have a major effect on green-ball quality for medium molecular weight CMC.

Jan 1, 1988

By R. C. Kellner

Duval Sierrita Corporation, a wholly-owned subsidiary of Duval Corporation, operates an 86,000 STPD copper-molybdenum concentrator near Tucson, Arizona. Shortly after production commenced in February, 1970, it became apparent that the reduction crushing system represented a limitation to reaching the design capacity of 72,000 STPD. The development work performed on the reduction crushers in order to first meet design capacity, and to subsequently increase production to 86,000 STPD is described in this paper. The Sierrita plant is a conventional three stage crushing sys- tem. All crushers were supplied by the Allis-Chalmers Corporation and consist of two 58 x 89 Superior gyratories, four 138b EHD hydrocones, and ten 384 hydrocones. Screening is performed prior to and subsequent to secondary crushing and in closed circuit with the tertiary crushers. Typical throughput rates and equipment sizes are presented in Figure No. 1.

Jan 1, 1975

By M. S. Klima

A 25-mm diameter dense-medium cyclone was tested to investigate the effects of geometry and operating conditions on cyclone performance when processing -150 I'm coal. The emphasis was on examining those variables (e.g., flow rate and inlet velocity) which impact the separation kinetics (specifically the number of g's and the mean retention time) and the occurrence of apparent bypass. Apparent bypass, indicated by partition curve "tails", results from the short circuiting of the feed coal to one or both of the product streams and represents a loss and/or contamination of the clean coal. This paper presents the results for this series of tests.

Jan 1, 1993

Grouting is mainly used to improve mechanical properties or decrease the permeability of rock mass around civil and mining projects. The purpose of this paper is to present the most effective factors on grout penetration depth in rock mass. Such factors are essential for reliable estimation of the grout penetration depth and the expense for cement take of any grouting project. In this paper, about 50 different types of the relations presented so far by various researchers to estimate the depth of penetration in fractured rock were studied. The effective factors are classified to rock mass properties, grout properties, and operational factors. Results show that firstly, the discontinuities aperture and Lugeon value are respectively the most investigated factors of rock mass properties influencing on penetration depth. Secondly, the yielding stress, viscosity, and density of grout are the most effective factors of grout properties. Finally, grouting pressure has an intense effect among other operational factors. The investigations were also verified in Siah Bishe dam case study. Keyword: grout penetration depth, rock mass properties, grout properties, operational factors.

Feb 27, 2013

By Todor P. Stefanov

The thermal draught within ventilation networks of underground mines depends to a great extent on the shafts depths and degree of change of ventilating air density. When the topology and space orientation of a ventilation network are constant, the dynamics of thermal draught is determined mainly by the variations of the heat- and mass-transfer processes in the openings. This conclusion follows from the well known basic theoretical notions about the thermal draught-aerostatics and thermodynamics [1]. Quantitative evaluation about the influence of heat- and mass-transfer processes on dynamics of thermal draught could be made through: direct mine measurements, special experiments and with the aid of mathematical models. The first two methods produce sufficiently accurative results, however it is very difficult to perform such studies, particularly when these processes are evaluated within a large scope and multifactor aspects. Mathematical models of thermal draught allow to overcome easily these difficulties. The degree of accuracy of results, obtained by this method, depends to a great extent on the degree of approximation achieved by the model to the real heat- and mass-transfer processes. In this paper, with the aid of Bulgarian developed method, algorithm and computer program V WT-4 - for complex evaluation of ventilation parameters in active mine ventilation networks [2], the authors investigate some changes in the thermal draught. Basically, the method is an iterating evaluation of an open set of equations, which represents relationships between the following basic parameters of a mine ventilation network: [ ]

Jan 1, 1980

By Bruno Bussière, Michael Aubertin, Robert P. Chapuis

Covers with capillary barrier effects (CCBE) have been used in recent years as gas barriers for the isolation of wastes, including reactive mine tailings. Capillary barrier effects help to maintain a high degree of saturation in the moisture retaining layer, which then reduces gas flux. Various factors affect the degree of saturation of the moisture retaining layer in a CCBE, such as the material water retention characteristics and layer thickness. Slope geometry can also influence the hydrogeological behaviour of a CCBE, but this factor has frequently been ignored in the past. In this paper, the authors show some results of a numerical study that illustrates the influence of slope on the behavior of capillary barriers made of different types of material. The numerical model calculations are based on an actual case of a CCBE constructed in northern Quebec. This investigation shows that the water content profile is greatly affected by the position along the slope. Thus, it is necessary to evaluate the influence of the geometry to properly establish the performance of a cover system.

Jan 1, 2000

By Gregg E. Korbin, Robin B. Dill, Corey T. Dare, Tor L. Brekke, Larry R. Myer

A study was conducted to develop a fundamental understanding of the relationship between the size of an advancing tunnel face, the rate of excavation, and stand-up time in squeezing ground. Stand-up time is defined as the time elapsed after excavation that an unsupported tunnel face will remain stable. Squeezing ground is argillaceous rock or soil that exhibits pronounced time dependence of deformation and strength properties in-situ. A case history study documented the nature, causes, and solutions of several cases of stand-up time problems observed in the field. Then, in the laboratory, a series of physical model tests were performed in which model tunnel size, face advance rate, material properties, and pressure (representing overburden pressure) were varied. Stand-up time was found to increase as advance rate was increased or tunnel size decreased. In addition, an influence of advance rate on the definition of stability ratios was established.

Jan 1, 1981

By Wen H. Su

Extensive investigation has been conducted to determine the causes of a series of roof falls occurring in a room-and-pillar working located in southern West Virginia. Underground observation, along with laboratory testings and finite element analyses were conducted to search for possible mechanisms for the roof falls. Results of the investigation have led to a better understanding of the mechanisms involved in the roof falls. Necessary modifications of mine layout and roof support plan are proposed for improving safety and profitability at the mine.

Jan 1, 1984

By Anis Farah, Khosrow Aref

Pull-out tests were conducted on cable bolts grouted with concrete, and cement paste. The influence of several parameters on the performance of these cables were studied under loading rates varying from very slow to relatively fast. These parameters include water-cement ratio, cable surface conditions, curing time and embedded length. In addition to being more economical, the results indicate that cables grouted with concrete have higher ductility and ultimate bond strength as compared to those with cement paste only.

Jan 1, 1986

By J. L. Vanderbeek

The SAG milling of ores with markedly variable grinding rates presents definite process control challenges. Decisions must be made regarding the selection of the most appropriate combination of mill volumetric load level, percent solids, and mill speed for the combination of ore types being processed at the moment. An investigation was performed concerning the effects of these parameters. General results are presented.

Jan 1, 1985

By George A. Desborough, Stephen J. Sutley, Reinhard W. Leinz, Paul H. Briggs

The mode of occurrence of metals in mine wastes is investigated using sequential extractions. Metals are extracted from some or all of seven operationally-defined phases: water-soluble, ion-exchangeable, carbonate, amorphous Fe-oxide, crystalline Fe-oxide, sulfide, and silicate. The quantity of metals extracted from each phase varies with particle size. The presence of jarosite (potassium end-member formula, KFe3[SO4]2[OH]6) influences the selection of the procedure for extracting the crystalline Fe-oxide phase. Anglesite (PbSO4) and cerussite (PbCO3) are extracted as several phases. Extraction results can be explained only in part by X-ray diffraction (XRD) mineralogy because of lack of specificity of the extraction procedures, relatively high XRD detection limits, and the presence of 40% XRD-amorphous matter in each waste. The increasing chemical strength of the sequentially applied methods provides a basis for judging metal availability, water-soluble metals being most available and silicate-bound metals being least available.

Jan 1, 2000

By E. G. Kelly, D. E. Walsh

The behavior of gold particles on a spiral was studied using radioactive gold tracers. The method allowed the effects of particle size, particle shape, pulp density, feed rate and splitter settings to be studied. Although the method has been successfully applied to other gravity concentrators, it was found that reliable results were more difficult to obtain on the spiral. However, these preliminary results show that, with suitable precautions, the technique is capable of providing valuable information, unobtainable from conventional studies, that could be used to better optimize spiral performance.

Jan 1, 1993

By D. E. Walsh

The behaviour of gold particles on a spiral was studied using radioactive gold tracers. The method allowed the effect of particle size, particle shape, pulp density, feed rate, and splitter settings to be studied. Although the method has been successfully applied to other gravity concentrators, it was found that reliable results were more difficult to obtain on the spiral. However, these preliminary results show that provided suitable precautions are taken, the technique is capable of providing valuable information that cannot be obtained by conventional studies, and could be used to better optimize spiral performance.

Jan 1, 1992

By G. Davis

Mineral properties and mineral firms often trade at a market value that is significantly greater than the value indicated by discounted cash flow (DCF) techniques. A possible explanation is that DCF analysis does not consider the value derived from managerial flexibility. Presumably, then, at least some of the difference between DCF value and market value is due to managerial flexibility. This paper surveys the recent attempts to empirically quantify the value of managerial flexibility using option pricing theory. The results indicate that managerial flexibility, at least as measured by the option pricing methodology, falls well short of explaining the gap between DCF value and market value.

Jan 1, 1995

By L. G. Austin, R. C. Klimpel

Batch breakage kinetic tests were performed in a mill of 0.3 m diameter for a range of mill conditions. Accurate simulation required the measurement and use of factors which accelerated the specific rates of breakage of the top sizes as finer material accumulated in the slurry. These factors depended on the size distribution expressed relative to the top size, not the absolute size, suggesting that they are due to a packing effect not a rheological effect. The data simulated correctly a series of steady-state continuous tests in a mill of the same diameter providing values were corrected to the hold-up, ball load, slurry density, and size distribution measured in the continuous mill tests.

Jan 1, 1990

By Chen Bingchen, Zhang Jian, Liu Jiaxiang

The influence of various installation angles of hydrocyclone on its operation indexes was investigated, and the correspondent mathematical models were established in this paper. The models developed in this paper can be used to the optimizing control of hydrocyclone and make the hydrocyclone as a particle size sensor.

Jan 1, 1995

By E. Stiakakis

The paper presents a geotechnical simulation of the "Mavropigi" open pit mine (Western Macedonia Lignite Center, Greece), using the finite element method. The simulation was based on the initial planning of the pit using Mohr-Coulomb and Soil Hardening models. Results indicate high stability factors as well as the magnitude of the expected horizontal displacements and floor heaving. However, these deformations do not influence decisively the overall stability unless locally adverse tectonics are encountered. Results can be used in the ongoing update of mine planning and stability evaluation.

Jan 1, 2006

By S. C. Chelgani

The Thor lake deposit is a world class resource of rare earth (REE) metals and minerals in Canada. Development work to optimize a REE mineral recovery process flow sheet is underway, however, given the ore mineralogy; the developed reagent scheme is relatively complex. As part of a research project, micro flotation tests were conducted on a feed sample in order to examine factors affecting stream partitioning. SEM-EDX was performed to evaluate variability in grain composition between streams (concentrate and tails) and TOF-SIMS surface analysis was used to determine statistically significant differences in surface species particularly related to potential activation (or depression) of the examined mineral phases. SEM-EDX analysis reveal that the concentrate has a significantly higher proportion of REE bearing grains (carbonates and phosphates) relative to the tail (almost none were identified). Spectral fingerprinting by TOF-SIMS has allowed for the identification of all reagent species investigated. Reagent signal intensity discrimination on test stream mineral surfaces was observed by the TOF-SIMS analysis using reagents at plant concentration levels. TOF-SIMS analysis confirmed that REE bearing grains reporting to the concentrate are doing so in response to collector attachment whereas grains reporting to the tail are doing so in response to a lack of collector and/or in combination with the presence of the depressant. The surface analysis of gangue phases reveal a similar reagent discrimination; the signal intensity of collector species was significantly higher on the concentrate samples relative to the tails while depressant species were significantly enriched on the surface of the gangue phases in the tail samples. A detailed evaluation of the surface species representing the various reagents used in flotation scheme revealed a distinct competitive relationship between two of the reagents. The surface analysis identified that when used in concurrently, there appears to be a negative feedback resulting in a significant reduction in loading for several of the collectors on grains reporting to the concentrate. An evaluation of the effect of reagents on REE mineral in pilot plant is currently under way. Key words: Rare earth minerals, Flotation, Surface chemistry, TOF-SIMS, SEM-EDX

Feb 27, 2013

By P. Hadzeriga

Ion exchange techniques have been growing fast and spectacularly in all phases of Science for the last two decades, but still its acceptance as a unit operation in Metallurgy is resisted. Mainly this is because ion exchange procedures are thought of as glamorous techniques by which only relatively expensive metals are to be recovered. Perhaps this concept comes from the early and basic marriage of uranium and other high price metals and ion exchange procedures. The general trend is that ion exchange technique requires equipment and materials which are too expensive to economically perform a chemical step whenever "cheap" commodities are produced. However, we are here presenting a means of utilization of waste hydrochloric acid by an ion exchange technique. We have studied this from the engineering and economic standpoint in a number of variations of the main procedure discussed here and we-conclude that under proper economic circumstances, the cost of the ion exchange material as well as the equipment and labor involved in the ion exchange section, is by no means unreasonable.

Jan 1, 1964