Search Documents

By Aixiang Wu, Minjie Zhang, Zhuen Ruan, Yiming Wang

 The paper combines theoretical and experimental analysis to improve the accuracy of predicting paste yield stress by slump flow. It derives an analytical model of slump flow for yield stress, providing a theoretical basis for quantifying the rheological properties of paste with slump flow. The study uses three different tailings-prepared pastes and constructs an empirical yield stress model, showing high accuracy and good generality.

Aug 1, 2023

By Aixiang Wu, Minjie Zhang, Zhuen Ruan, Yiming Wang

This paper combines theoretical and experimental analysis to conduct relevant research to improve the accuracy of predicting paste yield stress by slump flow. The analytical model of slump flow for yield stress is derived based on a mini-cylindrical mold with a height-to-diameter ratio of 1. It shows that the dimensionless slump flow is a monotonic decreasing function of the dimensionless yield stress and is independent of the material type (specific gravity), which provides a theoretical basis for quantifying the rheological properties of paste with slump flow. Three different tailing-prepared pastes were tested for their slump flow and implemented rheological tests simultaneously. The yield stress is obtained based on the Bingham model fit, as the measured value of the yield stress is substituted into the derived theoretical model. The studied pastes yield stresses range from 34.78 to 524.08 Pa, with corresponding dimensionless slump flow of 3.43 to 1.09. The results showed that the calculated slump flows were generally greater than the measured values. The analysis showed that this was mainly due to the thixotropy of the paste, with minor deviations ranging from − 1.5 to 5.8% for the less thixotropic pasted prepared from tailing C. An approximate analytical solution for yield stress as a function of slump flow is obtained using Taylor’s formula. However, it is unsuitable for predicting the yield stress because the yield stress calculated by this function is much higher than the measured value. The empirical yield stress model was constructed and experimentally verified. The results show that the empirical formula has high accuracy and good generality. The deviation of the studied pastes is between − 15 and 5%, which provides a practical method for rapid and accurate prediction of paste yield stress in mine sites.

Jun 1, 2023

By L. M. English

A basic model has been developed to help assess methane control needs for longwall mining of coal in gassy areas. Rather than depending upon reservoir and rock mechanic theory, it uses an empirically-determined gas emission rate as an input and operates on the assumption that, within a specific region and zone, gas emissions will be relatively equivalent for uniform incremental volumes of gob created by mining. The computer program divides longwall panels into segments, keeps track of the face advance, and generates emission rates and volumes for both the entire panel and for individual zones within the panel by summing values for all undermined segments. This model can aid the determination of the number, size, and location of vertical wells or other methane control applications that are needed for gob gas control.

Jan 1, 1998

By G. S. Dobby

High-intensity wet magnetic separators have been successfully introduced into the mineral processing field over the past ten to fifteen years, due largely to rapid advancements in magnet design. Wet magnetic separation, until recent years, was applied solely to the concentration of minerals of high magnetic susceptibility, such as magnetite, at relatively coarse sizes. Now, however, high-intensity separators are capable of treating weakly paramagnetic minerals and have extended the range of treatable particle size down to about one micrometre(1,2). . One of the more recent-high-intensity separators developed is the Kolm¬Marston Marston type high-gradient magnetic separator (HGMS) (3,4) It consists basically of an iron-clad solenoid surrounding a matrix material - a fine, ferromagnetic steel wool or expanded metal lath. A schematic diagram of the device is shown in Figure 1. Large, highly localized, pertebations of the magnetic field are created by the ferromagnetic matrix. It is these field gradients that are instrumental in developing large magnetic forces which act on the mineral particles. Operation of the separator is simple. Slurried sample is fed through the matrix and, depending upon the mineral parameters of particle size and magnetic susceptibility and. the operating parameters of flow rate, field strength and feed weight, some particles will be attracted to and adhere to the magnetized matrix, while the others will flow through the matrix. The separation is completed by later removing the background magnetic field and flushing the captured mineral particles into a separate container. The process can also be applied on a continuous basis (S).

Jan 1, 1977

By Aliakbar Golshani, Behnam Eslami

"Surface settlement adjacent to sensitive structures is a challenging issue in the tunnel engineering. In this study, 3D simulation of TBM excavation has been performed with the FLAC3D code and then the results compared with real monitoring data. Sensitivity analysis was carried out for all parameters affecting the surface settlement, such as the tail void grouting pressure (Pt), the face pressure (Pf), the tunnel diameter (D), overburden (q), shield thickness (t) and the length of the shield (L). The results show that the face pressure, tail void grouting and tunnel diameter have a considerable effect on the maximum ground displacement.In this paper, the monitoring data from Mashhad Metro was used to verify the numerical simulation. Data monitoring for about 47 sections between A2 and D2 stations was selected and a multiple regression analysis was performed. Based on this analysis, an empirical relationship was obtained for the coefficient of regression relationship which confirmed the sensitivity analysis.INTRODUCTIONThe surface settlement due to tunnel excavation is a complex issue, since the surface displacement is a function of several parameters that they are related to the excavation method, soil characteristics and TBM elements. Prediction of deformation is a very important issue, especially in urban areas, since these displacements may be affected the superficial structures. In recent studies, one of the most popular empirical relationships that is used to predict the surface displacement has gussian curve that it was suggested by Peck [1, 2]. An analytical relationship was proposed by Chow that its base assume was isotropic of soil, that surface settlement can be estimated based on the tunnel geometry and the shear modulus(G) [3]. Besides these methods numerical approaches such as the Finite Element Method (FEM) and the Finite Difference Method (FDM) have been used over the last twenty years, since numerical modeling has a high capability to simulation a complex soil conditions and irregular geometry [4]. In this study, all aspects of the EPB-TBM on Mashad Metro Line 2 were modeled and the most important influences on surface displacement in urban areas were determined [1, 3]."

Jan 1, 2016

By William G. Fischer

This paper attempts to close the gap between extensive rock testing with field measurements and the mine operator's need for safe mine layouts and alternatives. It was found that many of the variables that influence mine geometry and worker safety are relatively unimportant while others are critical. The development of empirical relationships which tie the critical variables to the "safe useful life" of a trona mine layout and observations made in 140 production areas where the variables were researched over a fifteen year period are discussed. The concepts presented may have applicability in mine design for other bedded deposits.

Jan 1, 1984

By J. H. Kim

Since the Hardy Cross numerical algorithm was applied to the solution of mine ventilation networks, there have been numerous developments in ventilation network analysis procedures. The Newton-Raphson method, the linear theory method, and the second-order approximation method are three of the additional approaches that have been applied. The efficiency of a ventilation network analysis procedure depends not only on the method of solving the system of equations derived from ventilation networks, but also on the method of deriving the equations through selection of the meshes. This paper investigates the impacts of three mesh selection methods on the efficiencies of four ventilation network procedures. The minimum-resistance spanning tree method is the most popular procedure for selecting meshes. The shortest-path method was suggested by Epp and Fowler (1970) for improvement of the Newton-Raphson method. The minimum-resistance-path method is suggested here as the third method of selecting meshes. The effects of these three methods on the Hardy Cross method, the Newton-Raphson method, the linear theory method, and the second-order approximation method are analyzed in this paper. These network analysis methods have been summarized in the paper by Kim and Mutmansky (1991).

Jan 1, 1992

By J. M. Mutmansky

Introduction Since the Hardy Cross numerical algorithm was applied to the solution of mine ventilation networks, numerous developments have taken place in ventilation network analysis procedures. The Newton-Raphson method, the linear theory method and the second-order approximation method are three of the additional approaches that have been applied. The efficiency of a ventilation network analysis procedure depends not only on the method of solving the system of equations derived from ventilation networks but also on the method of deriving the equations through selection of the meshes. This paper investigates the impacts of three mesh selection methods on the efficiencies of four ventilation network procedures. The minimum-resistance spanning tree method is the most popular procedure for selecting meshes. The shortest-path method was suggested by Epp and Fowler (1970) for improvement of the Newton-Raphson method. The minimum-resistance-path method is suggested here as the third method of selecting meshes. The effects of these three methods on the Hardy Cross method, the Newton-Raphson method, the linear theory method and the second-order approximation method are analyzed in this paper. These network analysis methods have been summarized in the paper by Kim and Mutmansky (1991). Mesh selection methods A procedure for mine ventilation network solution based on mesh equations typically consists of two steps: • the mesh selection step and • the network solution step. The mesh selection step establishes a set of independent equations to solve the network. The resulting equations are nonlinear. One method of solving nonlinear equations is to linearize the equations and iteratively solve these linear equations. The four analysis methods previously discussed in this paper use this approach. The linear equations required for solution can be written in matrix form as: P•dQ = dF (1) where P is the pseudo-resistance matrix, Q is the quantity matrix, and F is the Jacobian matrix (Kim and Mutmansky, 1991). The efficiency of the solution method depends on the characteristics of the P matrix, which in turn depend on the method of selecting meshes. To understand the impacts of the mesh selection methods on the efficiency of the ventilation network analysis procedures, the characteristics of the P matrix must be understood first. The diagonal elements of the P matrix, m in number, are the sums of the pseudo-resistances of the branches contained in the m meshes necessary for solution. The off-diagonal elements are the sums of the pseudo-resistances of the branches shared by two meshes. For example, P12 (first row, second column element of the P matrix) is the sum of the pseudo-resistances of the branches common to mesh 1 and mesh 2. When solving the system of equations expressed in Eq. (1), three of the iterative procedures (the Newton-Raphson, the linear theory and the second-order approximation methods) use the direct factorization method (Burden and Faires, 1985) on the P matrix. When the direct factorization method is used, the computational efficiency is enhanced by larger diagonal elements and a sparser P matrix. Generally, the sparsity of the P matrix is more important than the size of the diagonal elements. There is no known mathematical method of predicting the efficiency of these procedures, but heuristic methods can be used to study the efficiency. The Hardy Cross algorithm applies the Gauss-Seidel method of splitting the P matrix and applies the Newton-Raphson procedure. The efficiency of the Hardy Cross method depends on the spectral radius of the matrix[[D-L]-1U], where D is the diagonal, L is the lower triangle and U is the upper triangle of the P matrix for the Newton-Raphson method (Ortega, 1972). The smaller the value of the spectral radius, the faster the convergence. As with the other three methods, larger diagonal elements and a sparser matrix aid in faster convergence. With the Hardy Cross method, however, the size of the diagonal elements is more important than the sparsity of the matrix. Remembering that each of the diagonal elements of the P matrix is the sum of the pseudo-resistances of the branches in a mesh and that each off-diagonal element is the sum of the pseudo-resistances of the branches shared by two different meshes, the following strategies can be used: • Avoid having branches with larger resistance values shared by multiple meshes. This increases the size of the diagonal elements and reduces the chance of off-diagonal elements being large.

Jan 1, 1993

By Joseph B. Alberts, David D. DiPonio, Francis B. Manning

From 1996 to 2001, Wayne County and 13 suburban Detroit communities constructed the Downriver Regional Storage and Transport System (DRSTS) to improve area water quality, protect public health and alleviate basement flooding. The project consisted of a 10-mile long storage and transport tunnel, a pump station at the existing wastewater treatment plant, 9 miles of relief sewers (6 in tunnel and 3 in open cut). The work was separated into 10 contracts. Due to hydraulic design requirements and other constraints, the tunnel profile was located generally 65 feet below ground surface within a soft to medium clay strata which skimmed along the top of a very dense glacial till “hardpan” overlaying bedrock. Boulders within the tunnel bore were recognized as a significant, but indeterminate risk. This paper presents a case history of the owner’s contracting strategy for risk assumption and management of the boulder impacts on the project. Actual conditions encountered during construction and contractual adjustments made to address problems are reviewed, and recommendations for future contracts are included.

Jan 1, 2003

By Ted H. Eyde

Improving the mineral industry's tarnished image describes in a nut- shell the reason why the Speakers Bureau of the Tucson Subsection of the AIME was formed. Let's go back in time about 3 years to the fall of 1971. Literally thousands of bills detrimental to the mineral industry were being introduced into Congress and State Legislatures. Unfortunately, many were being passed and signed into law. Clean air and water, zero pollution, preserve the environment, ecology, biodegradeable, wilderness were the words that the self- styled ecologists and environmentalists were preaching. The mineral industry either sat mute or in place of acting, reacted in a way certain to attract a maximum amount of bad publicity with a minimum amount of rhetoric. A mining company president, for example, commenting on the primary air standards in Arizona was reported by the press as having said, "we'll shut all the smelters down and put thousands of Arizonans out of work if we have to meet the Arizona standards." Or another defending a poorly planned highly visible open pit nonmetallics operation, "we'll take the whole mountain down if we want to, and nobody can stop us" and still another manager of Operations, "the bottom line is all that counts, to hell with all of this environmental nonsense."

Jan 1, 1975

By Dennis D. Fischer

The second underground coal gasification experiment conducted by ERDA's Laramie Energy Research Center at a site near Hanna, Wyoming, was completed on July 30, 1976. During the experiment production reached 0.32 Mm 3/d (12 Mft3/d) of 6.9 MJ/m3 gas (175 Btu/ft 3 ). Approximately 6100 tonne (6700 ton) of coal were gasified during the experiment. Energy return ratios of 4.5 to 5.3, cold gas - thermal efficiencies of 76 to 89 percent, and overall process efficiencies of 65 to 74 percent were achieved during the second Hanna experiment. This paper describes the experiment and the results obtained with emphasis given to the determination of the energy recovered relative to energy consumed in conducting the test. Data from this determination are compared with previously published data from the first test conducted at Hanna during 1973-1974.

Jan 1, 1977

By Caibin Wu, Chengfang Yuan, Jiaqi Tong, Zhilong Cheng, Ningning Liao, Chong Zeng

In a series of Julius Kruttschnitt size-dependent breakage models, the cumulative percentage passing 1/10 of the initial size is used as a fineness indicator for scientific research and the selection of grinding equipment. However, in industrial practice, it is quite customary to use the mass percentage passing 75 μm as the indicator. In this paper, based on the energy-particle size model, quartz and calcite, two materials with distinctly different hardness, were used as test samples in a conical ball mill. At the same specific energy, the value of the cumulative percentage passing 1/10 of the initial size decreased while that of the mass percentage passing 75 μm increased with finer feed size. The experimental test values of the mass percentage passing 75 μm have a good linear relationship with the model predictions, which suggests that the particle size energy relationship of the mass percentage passing 75 μm and Ecs can be used instead of the cumulative percentage passing 1/10 of the initial size and Ecs. By building family curves, when particle size x < 300 μm, the family curve can be well fitted, and the fine particle size distribution of the whole product can be reconstructed.

Dec 22, 2022

By Eugene L. Foster

The engineering profession has traditionally devoted its efforts to understanding and modifying the Earth&apos;s environment in order to adapt it to man&apos;s needs. In appraising our overall performance, I would have to say it has been a mixed bag. In many areas, notably communications taken in the broadest sense, and development of creature comforts, we have done a good job. In others, we have failed, particularly in our assessment of the effect of our work on the environment. Our failures have been due in part to a lack of understanding or foresight, and in part to a disproportionate emphasis on lowest first cost. Now, with an increasingly large number of people living in a finite environment, there is an urgent need for reassessment. It is no longer possible to pursue a single objective without regard to its side effects. Our projects are too large, and there are too many of them. Environmental impacts must be taken into account in all important engineering decisions of the future. There are forces at work which will help to bring this about. Thinking people everywhere have realized that adverse alteration of our environment eventually affects every one of us. The majority of our citizens, who now live in cities, are beginning to appreciate the advantages of a good natural environment in a way which others who have been closer to the soil have appreciated for years. Our people have flocked to the cities because they wanted to be "where the action is." At the same time, there is a strong desire for what we have come to call the quality of life. Today, we all want the standard creature comforts. We want to be able to move freely

Jan 1, 1974

By David R. Klug, Chris Gause, Troy L. Page

The Inter-Island Tunnel is one of two undersea tunnels which are part of the Boston Harbor Clean-Up Program. The tunnel is 7.7 km (25,160 ft) long, bored to a 4.3 m (14 ft) diameter in the Cambridge Argillite Formation and was finished to a 3.5 m (11.5 ft) diameter final concrete lining. The owner is the Massachusetts Water Resources Authority (MWRA) who is a regional authority responsible for overall design and construction. The tunnel&apos;s primary purpose is the transport of untreated effluent from Nut Island facility in Quincy, MA to the new treatment plant at Deer Island. Two sludge lines are installed for the transport of sludge from Deer Island to Nut Island. During construction the contractor encountered fault zones, fractured strata, and soft ground tunnel sections which liberated more ground water than was originally anticipated by the project designer. Ground water was controlled during mining and the placing of the final lining. The final lining of cast-in-place concrete had to be backfill grouted to cut off water inflows and provide contact for equal tunnel loading which is critical in long-term design. This paper deals with an engineered backfill grouting system which was the first of its type to be used in North America. It discusses the geological conditions encountered, the design criteria used in the evaluation process, and an indepth review of the various system components. It demonstrates how contractors can use knowledgeable and professional industry suppliers to solve difficult construction problems.

Jan 1, 1999

By Lawrence Adler

The design of an underground opening involves the coincidence of two highly complex and poorly specified components. First, the structural or mechanical characteristics of a geologic rock mass are not only extremely variable but are also very difficult to evaluate. Second, the general lay¬out of mine workings contains a large degree of indeterminancy as to the structure itself as a result of the indefiniteness of the mining process, and also because of the inherent redundancies associated with bulky and weighty structures. Even for the relatively simple problem of tunneling this complexity is well recognized to be "without question that to which the study of geo¬logy (for the Engineer) can most fitly and usefully be applied".1 It can, therefore, be appreciated that the comprehensive opening design problem involves a complicated assemblage of component structures made up of a sketchily defined, or sometimes even an undefined material and acted upon by largely unknown tectonic forces.

Jan 1, 1968

By C. John Dunnicliff, Birger Schmidt

INTRODUCTION To be effective and useful, monitoring of tunnel construction must be carefully planned throughout all steps. A vital and frequently overlooked step is a clear definition of the specific purposes of the instrumentation. Most tunnel construction monitoring has in the past been of benefit to research, the advancement of tunneling practice, wittingly or not. The development of monitoring instrumentation for the benefit of the project from which the data are recovered has very significant potential for risk and cost reduction of soft ground tunneling. A systematic approach to tunnel construction monitoring, from conception to full implementation, includes at least the following nine tasks or steps: Definition of benefits and purposes; design and project specification to draw full benefits; selection of monitoring parameters; selection of instruments and writing of specifications for procurement and installation; procurement and installation; reading and maintenance; data storage and retrieval; interpretation; implementation. Some of these steps are fairly easy and resolved through the use of established theories and technologies. The difficult ones are those that require the bending of minds, those that involve changes in the ways engineers design soft ground tunnels, the way owners pay for tunnels, and the construction is managed, inspected and controlled. Performance monitoring can be of benefit to the owner, design

Jan 1, 1974

By Qing-Wang Hao

In this paper, the authors attempt to develop engineering based approaches for estimating safety factors against pillar and floor failures and predicting likelihood of subsidence events over abandoned coal mines in Illinois. There are two critical problems involved in the analysis: determination of geotechnical properties, and consideration of time effect. The authors attempt to solve the problems by generating hypotheses, which are used to modify existing engineering models for estimating pillar and floor safety factors. The modified models are validated using data from two well established databases of subsidence events over active and abandoned mines in Illinois. The data analysis suggests that most of the trough type subsidence events in Illinois were caused by floor failures rather than pillar failures. The subsidence incubation period seems to be directly related to initial floor safety factors at the time of mining. This correlation can be used to predict the likelihood of subsidence and to assess subsidence risks within both spatial and temporal contexts where detailed mine maps are available.

Jan 1, 1986

By A. W. Khair

This paper presents an engineering approach to solve a complex ground control problem at reduced cost, allowing the mine to be operated safely and economically. The mine has experienced serious and complicated cutter roof problem in the entries. This cutler roof problem has delayed the advance of the entry development considerably and cost of these entries is very high due to the requirement of very heavy artificial supports. The analysis includes assessment of the cause of cutter roof and step by step action taken to improve the entry condition through appropriate longwall panel entry design and roof support system. The approach for solving the problem was two-fold: 1) to apply yield pillar concept in order to reduce the effects of in-situ horizontal stress in the roof strata and 2) to find an effective way to reinforce the roof strata and to support the fractured roof and avoid caving.

Jan 1, 1990

By Michael J. Virnig, Murdoch W. MacKenzie, Michael R. Davis

The objective of this paper is to present preliminary capital and operating cost estimates (±25%) comparing conventional carbon-in-solution (CIS) with resin-in­solution (RIS) using AuRIX® 100 for the recovery of gold and silver from typical heap leach solutions. Preliminary testwork was carried out with AuRIX® 100 using real and synthetic leach solutions to determine the technical viability of the resin for gold/silver recovery and to provide process design parameters for the preliminary RIS circuit. The scope of the resin testwork was sufficient to support the level of accuracy applied in the capital and operating cost estimates. No parallel testwork was carried out with activated carbon. Industry standard design data and operating data from existing CIS operations were used as a basis for the comparison. Both the capital and operating cost comparisons indicate a substantial savings for a RIS circuit using AuRIX® 100 (- 14 to 18% in terms of capital and 25 to 35% in terms of operating costs) over a conventional CIS circuit depending upon solution flows and grade.

Jan 1, 1999

By Alex G. Sciulli

According to recent estimates, nearly 30 percent of the material from underground coal mining in the United States is rejected on the surface as waste. This accumulation of almost three billion tons of coarse and fine coal refuse is primarily from coal cleaning operations. The marketable coal is intermixed with sandstone, clays, shales, and carbonaceous rocks, which must be removed and disposed of in an acceptable manner. The disposal of mineral wastes is a major environmental concern. The most common types of environmental problems associated with coal refuse disposal are acid formation, erosion, and sediment control. Other areas of concern include air and water quality, combustion control, mine sealing, and reclamation. This paper focuses on these topics and attempts to outline special environmental features which can be incorporated into the design and construction of a coal refuse facility. Often these measures can minimize and possibly eliminate the potential environ- mental hazards. It is imperative, however, that these measures be adopted prior to and during construction, because of the relative ease and cost savings compared to post-construction implementation.

Jan 1, 1983