Search Documents

By D. F. Malan

This study Investigates transient closure piles of tabular excavations. Measured closure profiles in stopes indicate that time-dependent acts f the rockmass can be very prominent but such effects have been largely neglected in past analyses and modelling. This was due to a poor understanding of the time-dependent mechanisms controlling closure rates This paper investigates the feas-ibility of representing the rockmass as a visco-elastic medium. Currently, no analytical solution for the viscoelastic convergence of a tabular stope is available in the literature. Therefore, the author derived a solution using the correspondence principle and a known elastic solution. It is assumed that the rockmass behaves elastically in hydrostatic compression and as a Kelvin substance in distortion A parametric study is Included to aid in the calibration of the model parameters, together with a discussion on the correct calibration of these parameters from experimental data.

Jan 1, 1995

By M. Wong-Kian, L. A. Cornish, A. van Bennekom

Samples of four different satellite materials were prepared by either hot isostatic pressing (HIP) of the powder or tungsten inert-gas welding of rod onto a 316 L stainless-steel substrate. The samples were subjected to a series of comparative erosion corrosion tests, and generally the Hipped samples experienced between 13 and 24 per cent less loss in mass than the equivalent welded alloys. Resistance to erosion corrosion increased with increasing carbon, chromium, and tungsten contents. Metallographic studies indicated the differences in carbide content between the different satellite materials, and the differences in morphology between the Hipped and welded samples. Finer and more homogeneous microstructures were

Jan 1, 1995

Blasting in a gold mine has to satisfy the following set of techno economic conditions: good fragmentation, minimum stopped width, minimum number of rock falls, cost effectiveness. Results of a comparative study of the performance of a Low Density Anfo (LDA) and a conventional Anfo (ANFEX) are discussed. LDA appears to be more cost effective. The same borehole volume can be charged with material of reduced specific gravity. The velocity of detonation (VOD) is increased in the case of LDA resulting in more breakage as a result of shock energy than from the energy in the gas phase. This leads to less damage to the excavation and more favourable breakage of the excavated rock. As a result the overall economics of the mining operation is improved.

Jan 1, 1995

By S. M. Spottiswoode, A. J. Jager, N. C. Gay, J. A. Ryder

The South African mining industry is at present planning to extract orebodies at depths of up to 4 km. To do this cost effectively and, at the same time, ensure safe working conditions for mining, the personnel will require both the development of new strategies and the implementation of current rock-engineering technological developments on a wide scale. This paper covers most of the technological developments likely to be required for mining at very high stresses, but it is clear that improved regional support systems will need to be developed to ensure defective stability of the rockmass during mining operations. Similarly, it is clear that improved strategies for mining in large-scale geologically disturbed areas, where slip on faults or dykes can result in wide-spread rockburst damage, will have to be addressed

Jan 1, 1995

By K. I. Afewu, L. C. Woollacott

The design of in-pulp adsorption vessels in the gold industry has, for the most part, been seen as a problem involving the suspension of fine particles o ore in a slurry. The need for the vessel to be designed as a mass-transfer contactor has received insufficient attention. The current series of papers addresses this need The previous paper considered the question of the scale dependence of the film transfer coefficient. This paper examines the mixing considerations that are relevant. A review of the literature and an examination of a limited set of data provide some insight into the mixing conditions needed for the dispersion of the particles of adsorbent. The mixing requirements for the suspension of the ore particles are also considered, and conclusions are drawn in regard to the design of mechanically agitated vessels for gold in-pulp adsorption circuits.

Jan 1, 1995

By L. A. Cornish, B. Eatwell

Austempered ductile iron (ADI) is a ductile iron which has had its matrix toughened by an austempering process. The alloy exhibits remarkable properties, which it owes to a unique microstructure comprising graphite nodules embedded in a matrix of acicular ferrite and carbon-enriched austenite. The properties include high strength combined with high toughness and ductility. Excellent wear resistance is also exhibited because, under strain, the austenite is transformed locally to martensite. Samples of ductile iron were austempered to produce grades I and IV AD!, and were tested at various strain rates. The grade IV ADI exhibited higher strengths and lower difficulties, and the strengths were found to be more dependent on strain rate. Transformation to martensite was more prevalent at the lower strain rates. A mechanism of increased flow stress and work hardening in the austenite of the matrix is proposed to explain the higher strength of the samples at high strain rates, where significantly less martensite is formed in the matrix.

Jan 1, 1995

By A. J. Jager, J. A. Ryder, M. U. Ozbay

This paper deals with procedures used for designing pillar systems in hard-rock tabular mines operating at shallow depths, typically less than 1000 m. A comprehensive review if current practice identifies four types if pillars, namely non-yield, yield, crush and barrier pillars, and the main principles for designing these pillars are outlined. It is shown that the current design methods for pillar systems in South Africa are mainly empirical, each mine developing its pillar-design methods based largely on practical experience. This results in varying pillar layouts, even between neighbouring mines, despite similarities in geology, and depth if mining. It is suggested that some current layouts may fall short if being the best as regards safety, the maximum safe extraction percentages, or flexibility in accommodating future mining scenarios in deeper or otherwise different geological conditions.

Jan 1, 1995

By G. J. Krige

The extent of ground movements and stress concentrations in the vicinity of the reef in the deep mine-shafts used in the South 4frican gold-mining industry have led to the requirement that special tower structures be developed to span the reef intersection zone in several new shafts. So that structural engineers are able to design these towers, it is necessary to model the dynamic behavior of conveyances traversing them in some way, to provide a means to determine the magnitude of the forces generated. This paper describes the development of two such procedures. The first is a numerical method, utilizing a step by- step integration technique to track the motion of a conveyance through a tower. This technique has been implemented in a computer program, and some results are given.

Jan 1, 1995

By W. O. Ortlepp

This note considers the most fundamental concepts of support design for deep underground openings and discusses them briefly in the context of tabular stoping and deep hard-rock tunnelling. It concludes that the conventional re-bar, mesh, and lacing methods that have been widely used in deep gold mines are quite inappropriate for the support of highly stressed tunnels. The following is suggested as the criterion for adequate dynamic support: the energy absorbed by a support unit (yielding through some acceptable limited displacement) should exceed the kinetic energy generated by the mass of rock that is intended to be retained by that unit.

Jan 1, 1995

Using the philosophy that 'change cannot be introduced through memos-you have to get people emotionallyinvolved', SRK's Environmental Group in South Africa is helping clients communicate their environmental management objectives more effectively through the powerful medium of interactive industrial theatre. Existing and pending environmental legislation, international pressures, and growing awareness of the environment have led South African industry to the point where responsible care, for both the environment and the health and safety of those affected by the activities of an industry, is now a focus of management policies.

Jan 1, 1995

By A. Koursaris, Y. Turan

The object of this study was to investigate the i1Jfluence of nitrogen on the structure and properties of AISI 310S steel. Experimental ingots of the steel with nitrogen contents of up to 0,525 per cent by weight were prepared, hot-rolled, and tested after various treatments. The rollability of the material was adequate. The yield strength, tensile strength, hardness, and fatigue properties of the new alloys improved with increasing nitrogen content. The impact properties improved slightly. Empirical equations were developed for the calculation of the yield and tensile strengths, as well as the difference between these two properties, with increasing nitrogen content.

Jan 1, 1995

By M. J. Gouws, T. P. Knoetze

The spontaneous combustion of coal and the explosion of coal dust are two phenomena that were identified by the South African mining industry as requiring investigation. Research contracts were awarded to the G.P. Badenhorst Research Facility of the CSIR and the Department of Mining Engineering of the university of the Witwatersrand by the now defunct National Energy Council. Both projects entailed tests on numerous coal samples in specially designed apparatus. Since the completion of the project, attempts have been made to predict experimental results without incurring the cost of performing experiments. This paper describes predictive indices, based on routine laboratory tests, that were developed by the different research teams for their particular projects. A comparison of the results obtained by applying the spontaneous combustion liability index and the explosibility index to common coal samples indicates that, in general, propensity to spontaneous combustion and explosibility exhibit an inverse relationship. A brief overview is given of some major South African coal-mine disasters.

Jan 1, 1995

In order to test the applicability of elastodynamic codes in the modeling of mining related problems, comparisons are made between seismic data and numerical analyses. The dynamic finite difference program WA VE is used for the modeling of a horizontal stope in a deep mine. The slip along a vertical fault situated within the positive excess shear stress lobe of the stope initiates seismic waves. The stope-fault geometry is modeled in both two and three dimensions. The three dimensional non-slip weakening WAVE analyses correlate well with Brune's analytical model. For accurate modeling of the peak particle velocities predicted by McGarr's empirical relationship, it is recommended that a three-dimensional stope -fault model is used, with the amount of slip weakening dependent on the magnitude of the event.

Jan 1, 1995

By D. A. J. Ross-Watt

Right now the South African mining industry is a high-profile, vital contributor to the nation just as it has been for the past one hundred and twenty-six years since the discovery of diamonds-perhaps even further back if the mining of copper, iron ore, tin, and other minerals in earlier centuries is included. The media in 1995, as has been the case over the years, bear testimony to the complex interactions between the industry and its stakeholders: shareholders, government, employees and their unions, training and educational institutions, researchers, markets, the public, and suppliers of goods, services, and infrastructure. The pressures and challenges that the industry continues to face can be summarized as safety and health, competitiveness, and social and environmental responsibility. There are no surprises here. The motivation for the industry to perform well in these areas is clear; the focus I intend to bring is on the most important tool required for success-that of good mining engineering. This Address sets out - to review the mining aspects that have been discussed in South Africa during the first five years of the decade, a discussion that shows the return of the country as an important mining forum, confirms the role of professional institutes and associations in the development of mining engineering, and brings current relevant issues into focus - to highlight the vital role of mining engineering in the industry, and to identify priorities for the remainder of the decade - to provide the prospective mining engineer, the mining-engineering student and trainee, and the practising mining engineer and mine manager with a better appreciation of the mining-engineering discipline. institutes and ssociations

Jan 1, 1995

By M. R. Grant, G. S. Kruger, H. D. van der Merwe, T. N. Huffman

Sixteenth to seventeenth century Kalanga miners dug a series of sub-vertical shafts into a 10 to 30 m wide zone of copper ore at the Thakadu Mine near Matsitama, Botswana. They went down at least 6 m in search of thick malachite veins. The host rock was hand 'cobbed' to remove the veins, which were then smelted nearby in small bowl furnaces. Evidently, the furnaces lacked clay superstructures, since a simple pit was sufficient to smelt the almost pure malachite. The copper bloom was probably refined in villages further away.

Jan 1, 1995

By H. A. D. Kirsten

The paper reports on loading tests conducted on shotcrete reinforced with mesh and various types of steel fibre, and compares the results with the energy absorbing capabilities of 16 mm rebar shepherd's crooks. It is concluded that mesh-reit1forced shotcrete has sufficient energy-absorbing capabilities to contain rockbursts of significant magnitude, having greater energy absorbing capabilities, even at a thickness of 50 mm, than 16 mm rebar shepherd's crooks. Fibre-reinforced shotcrete has energy absorbing capabilities of the same order as, or better than, those of 16 mm rebar shepherd's crooks, but its performance is erratic.

Jan 1, 1995

The quality of life in many countries of both the developed and the developing world is strongly affected by the products and processes of mining industries. The first Issue in this new series brings together a set of review articles by leading authorities in the field which, taken together, provide a thorough and detailed survey of many of the key topics of current concern relating to the environmental impact of mining. The level of treatment of most topics is at first introductory but evolves through to the advanced level of current research, backed up by extensive citations of relevant primary literature and other sources. Thus the Issue as a whole will be found equally valuable by students of environmental science and those actively engaged in research related to this theme.

Jan 1, 1995

By A. K. Biswas

Reviewer: R. H. Eric This edition is organized in twenty-three chapters, and contains exactly 500 pages including three appendices and an index. The first and second editions were published in 1976 and 1980 respectively, and both contained nineteen chapters. The second edition brought the operating data and process descriptions up to date. The third edition covers comprehensively the changes that have taken place in the primary copper industry over the past two decades. For example, reverberatory furnaces now make up only a third of the major primary smelting furnaces, compared with about three-quarters in the 1970s. Control of air and water pollution and recycling are given much more emphasis, along with novel and emerging technologies.

Jan 1, 1995

By G. V. R. Landman

Changes in the explosion behaviour of mixtures of coal dust, methane, and air when exposed to different energy sources are discussed. Changes to the lower explosive limits, minimum ignition energies, and rates of pressure rise when the same hybrid mixture of coal dust, methane, and air is exposed to ignition sources which are either spatially extended or spatially concentrated, are examined. A diagram is presented from which coal-dust loadings and methane presence can be determined which are below the lower explosible limits, and stated as a safety factor.

Jan 1, 1995

By P. R. Levey, A. van Bennekom

The effects of nitrogen alloying on the corrosion properties of austenitic stainless steels were investigated by a combination of potentio-dynamic and surface analysis techniques. The results indicate that nitrogen undergoes the phenomenon of anodic segregation, affecting both general and localized corrosion resistance. Nitrogen alloying is found to be beneficial to general corrosion resistance in a de-aerated sulphuric acid solution, but to be detrimental in an aerated solution of sulphuric acid This phenomenon is explained in terms of an ammonium-ion polarization effect. Localized corrosion resistance is found to improve dramatically as a result of nitrogen alloying, the nitrogen improving the formation, maintenance, and stability of the passive film in environments that promote pitting various theories that have been proposed to account for these phenomena are discussed.

Jan 1, 1995