Search Documents

By A. Koursaris, J. B. See

An investigation is described in which the resistivities of Mamatwan manganese ore, Delmas coal, and Iscor coke, at temperatures or up to 1400°C were determined, as well as the resistivities of mixtures of ore of a constant size range with Delmas coal or Iscor coke of three different size ranges. The resistivities of the ore and the coal were characteristic of those for semi-conducting materials, were strongly influenced by temperature, and decreased by several orders of magnitude between room temperature and IOOO°C. The resistivity of the coke changed only slightly between room temperature and 1400°C, and the resistivity of the coal approached that of the coke at I300°C. This provides support for the theory that the resistivity of carbonaceous reducing agents is primarily a function of heat treatment, and not of the rank and composition of the coal. Above 1200°C, the resistivity of mixtures of ore and coke fell steeply owing to an increase in the volume fraction of coke in the mixture and to the formation of slag. The results were similar for the three different size ranges of coke. The extremely high resistivities of ore-coke and ore-coal mixtures at Iow temperatures indicate that there is unlikely to be much conduction of current in the higher regions of a furnace. Thus, the resistance of a furnace is governed mainly by the conditions at the electrode tips and in the molten regions. To explain the very Iow resistances of furnaces, usually, about I m£?, it would be necessary for investigations to be conducted under conditions similar to those in the active zone of a furnace.

Jan 1, 1980

The May General Meeting of the Institute was held in Kelvin House, Johannesburg on 20th May, at 4.30 p.m. Mr V. C. Robinson (Vice-President) was in the Chair in the absence, overseas, of the President, Mr J. K. E. Douglas. There were also present 16 Fellows: Messrs J. A. Adamson, R. S. J. du Toit, J. A. Drummond, D. F. A. Grave, T. L. Gibbs, G. H. Grange, D. V. Howat, P. H. Kitto, Dr P. J. LIoyd, Messrs B. H. L. Leach, J. de V. Lambrechts, Dr J. T. McIntyre, Messrs C. S. MacPhail, P. W. van Rensburg, S. G. Taussig, W. S. Rapson. Six Members: Messrs E. L. Atkinson, R. Hemp, Dr J. Martinson, Messrs A. H. Munro, G. J. van Jaarsveld and J. H. Qwilliam. Two Associate Members: Messrs B. H. van Rensburg and H. Triiter. Four Visitors: Prof J. E. Kerrich, Dr G. K. Sluis-Cremer, Messrs D. Kisbey-Green and L. W. Isserow. For Secretariat: Mrs S. de Gersigny. Total present: 27. OBITUARY The Vice-President: "It is my sad duty to announce the death of Stephen Ring, a member who joined the Institute in ]961, and passed away on the 31st of December, 1969. I would ask you all to rise and observe a moment's silence. Thank you." MINUTES The Vice-President: "May we confirm the minutes of the Special General Meeting and Monthly General Meeting, held on 20th February, 1970, as published in the April issue of the Journal?" MEMBERSHIP The Vice-President: "I have much pleasure in announcing that the names of the undermentioned candidates, having been published in accordance with By-Law 5 2.2, Council has elected them to membership of the Institute in the following grades: Fellows: Denis Ian Field, Arthur Cecil Waiter Comyn, John Hall, Leon VercueiI. Members: Jan McLellan Vosloo, Jan van Velze. Graduates: Richard Darnley Beck, John Edward Andrews, Roderick Nowell Randell. Associates: Alexander Duncan Ross, Ian James Terrill. Students: Hendrik Jacobus Oostenwald Prins Smith, Graham Peter Gooding, Rudannes Raath Homan. "I welcome the newly, elected members to the Institute." GENERAL BUSINESS The Vice-President: "Are there any matters which you wish to raise under 'General'? There being no matters to raise under 'General', we will proceed to the next item on the Agenda." PAPER FOR PRESENTATION The Vice-President: "It is my pleasant duty to call on Dr du Toit to deliver his paper, entitled, 'The functional relationship between dust hazard and the rate of collecting funds to pay compensation for pneumoconiosis'." After the presentation of the paper (published in the March Journal) the Vice-President said: "This paper is a very important addition to the considerable volume of work applications on this subject of pneumoconiosis. The disease, in all its various forms, has received attention from many, many great men, both in the medical world, and engineers. The fact that there is this big volume of publications of literature on it still doesn't mean that we can get anywhere beyond the old, simple injunction, that the prevention of pneumoconiosis does not depend on compensation, levies or anything else. It simply depends on allaying dust as quickly as possible. "This paper, however, is another scientific landmark and I think, in a cold and dispassionate way, it sets out some important points in this whole subject of the relationship of the levy - the money of compensation to the dust which causes it. "I have, personally, very little to criticise in this paper but when I listened to Dr du Toit's final conclusions, I wondered whether the words, 'Within the data available', aren't the key to this whole situation. I agree that he has demonstrated a workable relationship between the current industries for levy and dustiness, but among the factors which he lists as being important, I know that there is one which is missing. This is extremely difficult to evaluate. It's a factor which has destroyed, on so many occasions, the work which has been done by so many genuine, intent, honest people working in this field, and this is this unknown factor, this hidden factor of political opportunism, which has so often played a very important part in pneumoconiosis compensation. "How many of us have seen the grubby, grasping fingers of power-mad demagogues, and I can name them for you - but I won't - and also the blatant vote-catching of certain politicians interfering in this field. How, at the end of all that, the poor scientist, the poor dedicated man in the Mines' Department, who has to write the law of compensation, can operate, I do not know. "From this picture the ordinary layman recoils in horror. Among the casualties in this particular war, which has been fought over so many years, I am perfectly certain, are some of the criteria of certification, especially in '56/,57, when that extraordinary condition, known as 'pulmonary disability' was introduced. I am sure there were casualties then, in the criteria of certification. "Nevertheless, this paper is a worthy addition to the long list of scientific work done on this so-important

By J. R. Menasce

Mechanization in low-stope panels situated in hard rock infers roof support by tensile bolting to allow free passage of trackless mining equipment in the production areas. This is in sharp contrast to conventional mining, where compressive roof supports?such as timber and grout packs?have traditionally been used, up to 1.5 metres from the production face. Bolting is a hazardous operation because material is dislodged from the roof during the drilling activity. Even with temporary roof support installed, small pieces of rock are dislodged by the percussive action of the drifter. Operations with the man situated directly under the drill, during the drilling activity, are hazardous. The only way to remove the hazard is to move the man away from the machine for as much as possible throughout the complete cycle Costs associated with safety cannot be quantified, but need to form part of the decision-making process. Machine selections based on purchase and running costs alone do not justify the investment cost of mechanized bolters. The equipment selection process needs to take into account the total cost of mining as well as the human safety impact and loss of production costs from having to re-bolt roofs in a production panel to prevent falls of ground. Labour costs in mechanized low-stope bolting are between one-quarter and half the labour costs of non-mechanized bolting. This paper reviews the mechanized bolting option versus handheld bolting from a mining process and cost perspective in a hard rock, low-stope room-and-pillar mining operation in the platinum and chrome industries.

Jan 1, 2006

By K. Thuro, R. J. Plinninger

ABSTRACT: Determining tunnel stability is a key issue during preliminary site investigation. In contrast, problems of excavatability have been largely ignored. While the choice of an economic tunnelling method is admittedly a clear priority in the planning stage, special investigations focus-sing on rock fragmentation (e.g. drilling or cutting performance, rock mass blastability or tool wear) are rarely carried out. This paper explores possibilities to quantify key parameters for rock mass excavatability in drilling, blasting and cutting by TBMs and roadheaders. RÉSUMÉE: La détermination de la stabilité du tunnel est une question clé lors des études prélimi-naires. En revanche, les problèmes d'excavabilité sont souvent en grande partie ignorés. Tandis que le choix d'une méthode de percement économique est évidemment une priorité claire dans l'étape de planification, des investigations spéciales se concentrant sur la fragmentation de la roche (par exemple le comportement de la roche au forage, à l’excavation ou au dynamitage et l’usure des outil) sont rarement effectuées. Cet article explore les possibilités pour quantifier les paramè-tres clé de la roche lors d’excavation par forage, dynamitage, au tunnelier (TBMs) ou à l’excavatrice. ZUSAMMENFASSUNG: Beim Tunnelbau wir meist die Vorhersage der Stabilität des ausgebrochenen Hohlraums als Schlüsselfragestellung betrachtet. Im Gegensatz dazu werden Probleme der Gebirgslösung weitgehend ignoriert. Während der Wahl einer wirtschaftlichen Vortriebsmethode während der Planungsphase meist noch eine gewisse Priorität beigemessen wird, werden spezielle Untersuchungen zur Gebirgslösung (Bohr- oder Schneidbarkeit, Sprengbarkeit oder Werkzeugverbrauch) nur sehr selten durchgeführt. Diese Publikation zeigt Möglichkeiten der Quantifizierung von Schlüsselparametern für die Gebirgslösbarkeit auf, also der Bohr- und Sprengbarkeit, der Fräsbarkeit mit Teilschnittmaschinen und der Schneidbarkeit mit TBMs.

Jan 1, 2003

By A. O. Filmer

An account is given of a study on the non-oxidative dissolution in aqueous acidic solutions of nickel sulphides of different stoichiometric composition, in which a rotating ring-disc electrode was used. The rate of dissolution was found to depend on the potential of the sulphide and the nickel-to-sulphur stoichiometric ratio. A maximum rate for the dissolution of nickel from nickel sulphides containing an excess of nickel was recorded at potentials around -0,2 to -O,3V. The rate decreased markedly at more anodic potentials. For nickel-deficient nickel sulphides, the nonoxidative dissolution rate increased with a cathodic shift in potential. Under open-circuit conditions, a nickel sulphide of a composition approximating Ni ,S. reacted most rapidly. The dissolution rate was controlled by either a chemical or an electrochemical reaction at the electrode surface, had an activation energy of between 50 and 65 kJ.mol-1, and was independent of stirring speed.

Jan 1, 1980

By R. Lechuti-Tlhalerwa

"Geometallurgy aims to improve mining project value by predicting the impact that ore and waste characteristics will have on mining and metallurgical processes. This requires integration of rich spatial models of orebody characteristics with validated process response models. These models have, until recently, been constrained by the spatial coverage and representativity of relevant data and the ability to validate predictions made.The revolution in the diversity and volume of data and computational power that is now becoming available for integrated geoscientific modelling of orebodies, and stochastic simulation of mining and mineral processes is accelerating. By embracing emergent integrated data analysis and simulation techniques, geoscientists and engineers can lead a transformation in the way the mining value chain, from orebody to recovery, can be conceived, evaluated, and operated by using the geometallurgical paradigm.This paper describes a methodology that is applied to an existing diamond operation. Analysis of spatial and process data is used to build an integrated geometallurgical value chain model (IGVCM). This IGVCM is used to generate geometallurgical options and evaluate their potential outcomes. The model facilitates the use of flexible, highly configurable, and potentially automated intelligent approaches to evaluate mining and mineral process configuration, and results in more robust design outcomes. The approach described here, and its successful implementation has potential to deliver step-changes in value. IntroductionGeometallurgy aims to identify treatability risks – and opportunities – that arise from the interaction of orebody characteristics with mining and treatment. Improved understanding of the rock/process relationships allows project planners and production teams to predict performance, identify potential shortfalls, and thus enable the proactive creation and evaluation of strategies to mitigate these risks. These advanced insights also create opportunities for continually improving operational performance through dynamically adapting and improving the process response to the changing properties of the ore (Figure 1)."

Apr 1, 2019

By G. A. Bezuidenhout, S. Bradshaw, W. Malan

"The purpose of the study was to investigate the feasibility of SiC reduction of low-grade concentrates from Lonmin’s Rowland and Easterns operations with respect to metal fall and PGM recovery. These concentrates are rich in SiO2 and MgO with low concentrations of chalcopyrite and Cr2O3. Pd is the most abundant of the PGMs. SiC reduction of samples was conducted at 1600? with 2.5-3.5 kg SiC per 100 kg concentrate.PGM recoveries for Easterns concentrate were better than for Rowland. More than 85% of the Ir and Pd and almost 60% of the Pt were recovered with 3.5 kg SiC per 100 kg concentrate. SEM of slag samples showed little entrainment of metallic prills compared to Rowland samples. This was attributed to the relatively higher melt viscosities of the Rowland concentrate. In order to decrease slag viscosity and to enhance PGM recovery, the FeO content of the Easterns concentrate was increased with the addition of 10 kg converter slag per 100 kg concentrate. Ir and Pd recoveries were increased to about 95%, while Pt recovery was around 70%. On the basis of these results an optimum feed ratio between Easterns and Rowland concentrates and converter slag is proposed. Carbothermic reduction of the optimum charge was also compared to SiC reduction. Carbothermic reduction yielded a marginally higher metal fall; however, the calculated gas emissions and energy requirements were higher than for SiC reduction."

Jan 1, 2015

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By G. van der Westhuizen, F. E. du Plessis

Ticor South Africa operates a dry mill at the town of Empangeni in the province of KwaZulu-Natal on the east coast of South Africa. The dry mill processes a non-magnetic mineral stream constituting rutile, leucoxene and zircon as major minerals, and minor quantities of ilmenite and other non-valuable minerals. For plant control and optimization, continuous ‘real time’ information about the mineral and chemical compositions in various plant streams is required. The current practice is to take samples at regular intervals and submit them for mineralogical(grain counting) and chemical analyses. However, these methods are time consuming, and in the case of manual grain counting, tedious and operator dependent. Until now an on-line or real-time instant mineral quantification system, which will be of great value in a plant operations environment, has not been available. Blue Cube Systems has developed a mineral quantification system using spectral mineral analysis. It measures and quantifies the composition of mineral samples instantly, providing consistent data in real time. A series of process stream samples from the dry mill mentioned above were used to evaluate the Blue Cube Systems instant mineral quantifier. This article will •describe the procedure of setting up and evaluating the Blue Cube Instant MineralQuantifier equipment •present its results, and •discuss the intended applications.

Jan 1, 2003

By D. Grgic, A. Giraud, F. Homand

RESUME : Le comportement mécanique partiellement saturé du minerai de fer a été étudié à partir d’essais de compression simple sur des éprouvettes à pression capillaire imposée par les solutions salines. Les échantillons restent peu saturés (32 %) même pour une humidité relative de 94 %, du fait de la présence de mésopores. Jusqu’à 90 % d’humidité relative la résistance diminue régulièrement. De 90 % à 94 % une forte chute est observée et pourrait être liée à la fois aux effets capillaires et à l’hydratation de certains minéraux. Le cycle hydrique subit par la roche dans la mine a été modélisé en 1D à l’aide d’un code de calcul entièrement couplé pour les milieux poreux partiellement saturés. Les calculs ont montré notamment une diminution importante en paroi des contraintes totales au cours de la phase de désaturation et une augmentation importante au cours de la phase de resaturation. Ces variations pourraient induire un endommagement du massif et être à l’origine d’instabilités, et soulignent l’intérêt d’une modélisation avec une géométrie plus adaptée. MOTS-CLEFS : mines de fer, partiellement saturé, pression capillaire, résistance, modélisation. ABSTRACT : The partially saturated mechanical behavior of iron ore has been studied from uniaxial compression tests on samples in which the suction is imposed with aqueous solutions. Samples are little saturated (32 %) even for a 94 % relative humidity because pores are too large. Up to 90 % relative humidity the strength decreases regularly. From 90 % to 94 % a great decrease is observed ; it could be explained by the capillary effects and the moisturizing of some minerals. The hydrous cycle imposed to the rocks in the mine has been modeled with an 1D fully coupled code for partially saturated porous media. The computations have shown an important decrease in the total stresses at the wall during the desaturation stage and an important increase during the re-saturation stage. These variations could induce a rock mass damage and instabilities, and highlight the necessity of a modeling with a well-adapted geometry. KEY-WORDS : iron mines, partially saturated, suction, strength, modeling. ZUSAMMENFASSUNG : Das mechanische Verhalten von teilweise gesättigten Eisenerz wird durch einachsige Druckversuche untergesucht. Die Prüfkörper haben einen durch Salzlösungen gestimmten kapillarischen Druck. Sie bleiben kaum gesättigt (32 %), sogar bei einer relativen Feuchtigkeit von 94 %, aufgrund der Anwesenheit von Mesoporen. Bis eine relative Feuchtigkeit von 90 % verringert sich gleichmässig die Druckfestigkeit und zwischen 90 % und 94 % merkt man eine starke Abnahme in Verbindung, möglicherweise, mit kapillarischen Effekten und Hydratation von bestimmten Mineralen. Die nümerische 1D Modellisierung des gezwungenen Wasserzyklus im Stein der Mine ist mit einem für porösen Medien ganz vernetzten Rechnungcode geführt. Sie zeigt besonders ein bedeutendes Sinken der Gesamtspannung während der Entwässerung und eine bedeutende Steigerung während der Sättigung. Diese Veränderungen könnten die Beschädigung des Gesteines herbeiführen und die Grundlage von Unstabilität sein. Sie unterstreichen die Wichtigkeit eine Modellisierung mit einer gut geeigneten Geometrie. STICHWÖRTER : Eisenminen, teilweise gesättigt, kapillarischer Druck, Druckfestigkeit, Modellisierung.

Jan 1, 2003

By R. T. Muller

Contribution to the above paper by R. T. Muller (Visitor) Demands are being made and pressure is being brought to bear on employers in South Africa to narrow or eliminate the wage gap between their White and Black employees. Few thinking people will dispute the fact that a constant improvement in the wages of Black personnel is essential, but this cannot be done merely by a redistribution of income in South Africa.

Jan 7, 1974

By A. F. Spinks, S. P. Nicholls

"The Lower Orebody at Chingola Division of Nchanga Consolidated Copper Mines, Limited, is a stratified orebody that is mined by a continuous caving system. The accurate determination of the developed and semi-developed ore reserves has always been difficult. The new system proposed in 1971 is designed to update and, as new informa¬tion becomes available, to account for the depletion of, the reserves.There are three main inputs to the system. These are borehole data, survey data and extractions data. The borehole data are input to a geological borehole master file system, which holds every recorded detail of a borehole in an easily extractable form. These data can be extracted for ore reserve calculations or for contour mapping of orebodies and rock types. The grades for use in the ore reserve calculations are extracted from the relevant boreholes.The survey data are information on the position of the blocks and drifts, taken from plans, and information on the scraper drift and trough drive positions taken from sections. The information is extracted from the plans and sections using a D Mac pencil follower. The ore reserve is calculated from the survey data and the borehole data.Data on extractions are taken from scraper operators' logs, tramming records, skips hoisted records and accepted mill tonnages and grades. Using these data, the mill tonnages are reconciled back to the drifts, to deplete the current ore reserves.As new workings are brought into operation and further evaluation holes are drilled, the relevant data are input and the new developed ore reserve is calculated."

Jan 1, 2014

By W. P. Nel

A fuel cell is an electrochemical engine that converts the chemical energy of a fuel, such as hydrogen, and an oxidant, such as oxygen, directly into electricity. The emerging fuel cell industry may represent a major opportunity for the global platinum mining industry. This is because low temperature fuel cell systems use platinum group metals as catalysts. Fuel cell vehicles may become the most important driver of future platinum demand within years of their commercialization. A great number of factors impact on and drive the diffusion of fuel cell vehicle innovation. Such drivers range from energy security to environmental concerns and the technological development of fuel cells and systems. Such factors and drivers of fuel cell vehicle diffusion are combined with the generic ?body of knowledge? on ?technology forecasting? and ?diffusion of innovation? to design a framework that provides a holistic approach to the analysis of this complex enterprise. An attempt is made in this paper to address the following questions: Which types of fuel cells require platinum group metals? Which types of fuel cells will achieve dominant design status? Will fuel cell vehicles diffuse successfully? How big will the impact of successful fuel cell vehicle diffusion be on future platinum demand? How well do fuel cell vehicles compete with incumbent technologies such as spark-ignited and compression-ignited internal combustion engine-driven vehicles? How soon will oil depletion start to drive the diffusion of fuel cell vehicles? How important is hydrogen as a fuel? What impact does the inadequate hydrogen fuelling infrastructure have on fuel cell vehicle diffusion? The paper contains some initial results of a research project that has the aim of producing a schedule of future platinum demand generated from fuel cell vehicles. Keywords: diffusion of fuel cell vehicles, technology forecasting, platinum demand forecasting.

Jan 1, 2004

By F. L. D. Cloete, A. K. Haines, T. D. Sampson, T. H. Tunley, W. A. M. te Riele

The recovery of zinc from pickle liquors by ion exchange A. K. HAINES. Ph.D. (Visitor) T. H. TUNLEY. B.Sc;.(Chem.Eng.)(Visitor), W. A. M. TE RIELE. pr, Eng.. Ph. D. (Visitor), F. L. D. CLOETE. M.Sc. (Chem..Eng.)(Visitor), and T. P. SAMPSON. Pr. Eng.. BSc, (Chem.Eng,). B. Econ. (Visitor) Picklers and galvanizers in and around Johannesburg are encountering an ever-increasing problem in disposing of spent liquors from their hydrochloric acid pickling baths. Particularly troublesome is the zinc-contaminated liquor that is produced as a result of the clean-up of rejects from the galvanizing operation. Because of the volatility of zinc chloride. this liquor presents difficulties when processed in a conventional pyrohydrolysis acid-recovery unit. The paper describes the Metsep Process. developed by the National Institute for Metallurgy and Woodall-Duckham S.A. (Pty) Ltd. which involves the use of continuous ion exchange for the separation of the zinc from the pickle liquor. and the use of liquid-liquid extraction for the conversion of zinc chloride eluate to salable zinc sulphate. A description of laboratory and pilot-plant tests is given. and the approach used in the design of a full-scale continuous- ionexchange plant is outlined.

Jan 11, 1973

Mill relining is a major contributor to overall plant downtime. Reducing the number of mill liner pieces removed from and replaced in the mill has a direct impact on the overall reline time and in turn, mill availability. To improve the mill availability of Ridgeway Operations' 32 foot SAG mill, a number of initiatives were implemented in terms of liner design. These included the conversion of the shell from 40 to 30 rows, reducing the number of pieces from 80 to 60 each shell reline and reducing the number of pieces from 48 to 32 per feed end reline. In addition, modifications were made to the discharge end of the mill to extend the life of the outer pulp lifter and discharge cone, thereby reducing the frequency of change out. The standard radial outer pulp lifter was converted to an angled design. The discharge cone was converted to the BullnoseTM design supplied by Bradken. This paper discusses the design changes made and the expected benefits to the Ridgeway Operations in terms of mill availability improvements.

Jan 1, 2007

By J. O. Claassen

"Homogeneous populations are required to perform descriptive, probabilistic, and inference statistics and to support stable, predictable mining operations. The geological and downstream processing environments are, however, highly heterogeneous. The complex nature of mining environments requires means to identify and define multipopulation environments that could affect the performance of mining value chains. A study performed at several operating mines suggests that the impact of heterogeneous or variable geological, mining, and plant processing environments on overall mining value chain performance may not be a key focus area at these operations. This was illustrated through the use of basic and spatial statistics, which included the log-probability plot, a modified range equation, and chronovariography. The findings reflect high relative variability in the geological and processing environments studied and mining operators’ inability to effectively deal with the sources and consequences of variability. The study suggests that a focus on heterogeneity in complex mining operations may significantly enhance overall mining performance. IntroductionHeterogeneity and why it mattersHeterogeneity refers to a state or quality of being variable/diverse and comprising different non-compatible elements or parts. In statistical terms a heterogeneous population can refer to a population comprising different non-compatible sub-populations or a multipopulation environment. The latter is commonly found in natural environments such as geological environments (Bardossy and Fodor, 2001). The inherent heterogeneity of complex geological environments is also referred to as spatial heterogeneity. Heterogeneity or variability, however, also occurs over time at mining operations. A case in point is variable ore composition on a conveyance system feeding a processing plant or product stockpile.Heterogeneity associated with the mining environment can significantly influence key aspects of day-to-day mining operations such as sampling, the use of descriptive, probabilistic, and inference calculations, and an operation’s ability to manage and control the mining value chain as a whole."

Jan 1, 2016

By J. P. Josien, J. F. Noirel, F. Lahaie, P. Bigarre, M. Al Heib

ABSTRACT: In June 2001, a fatal rockburst affected a longwall face in the Houillères du Bassin de Lorraine (HBL), France. Subsequently, a large operation of in situ stress measurements by overcoring was carried out with two main objectives: providing input data for the back analysis of the dynamic event and characterising the stress field in the next panels to be mined for identifying other potential high-risk zones. This paper makes a synthesis of the results of the overcoring tests performed and discusses those results in connection with the mining context, numerical model predictions, laboratory rock test results and microseismic activity. KEY WORDS: Mine, rockburst, stress, overcoring, measurement. ZUSAMMENFASSUNG: Im Juni 2001 hat ein Bergschlag eine Kohlengrube des Houillères du Bassin de Lorraine (HBL, Lothringen, Frankreich) schwer beschädigt. Nach diesem Unfall sind Spannungsmessugen durch Überborung durchegeführt worden, mit zwei Hauptziele : 1/ Daten zu liefern für die Retro-analyse des dynamischen Gebirgsschlag und 2/ die Spannungen in den zukünftigen Ausbauen so gut wie möglich zu charakterisieren, um eventuele andere Risikozonen festzustellen. Dieser Artikel stellt eine Synthese der erzielten Ergebnisse vor. Er diskutiert diese Ergebnisse in Verbindung mit dem gesamten Kohlengruben Zusammenhang, mit den Ergebnissen von numerischen Modellierungen, mit der Labor-Charakterisierung und mit der microsismische Überwachung. SCHLÜSSEL-WÖRTER: Kohlengruben, Bergschlag, Spannung, Überborung, Messung. RESUME: En Juin 2001, un coup de terrain a gravement affecté une longue taille aux Houillères du Bassin de Lorraine (HBL) en France. A la suite de cet accident, une importante campagne de mesures de contraintes par surcarottage a été réalisée, avec deux objectifs majeurs : fournir des données d’entrée permettant la rétroanalyse du phénomène dynamique et caractériser au mieux le champ de contraintes dans les futurs panneaux exploités afin de détecter d’éventuelles autres zones à risque. Cet article présente une synthèse des résultats obtenus, et discute ces résultats en liaison avec le contexte d’exploitation, les résultats de modélisation numérique, de caractérisation en laboratoire et de surveillance microsismique. MOTS CLES: Mine, coup de terrain, contrainte, surcarottage, mesure.

Jan 1, 2003

By G. S. Littlejohn

Following study of historical South African practice and a review of recent experience gained during the design, construction and testing of the high pressure plugs at the South Deep Water Barrier Project, this paper makes recommendations to improve practice. Initially, site investigation requirements are described with reference to geological, hydrogeological and seismic considerations, including site preparation and pre-grouting of the surrounding rock mass, if permeable. Structural and hydraulic aspects of plug design address topics such as residual permeability, aggressive mine water, plug materials, mortar strength and bleed. In situ thermocouples and piezometers are recommended to optimize the timing of plug tightening and monitor plug performance during service. Plug construction covers aggregate preparation, mortar quality control, plug tightening grouts, injection pressures, records and the overriding need for a method statement specification to control all aspects of plug construction. On completion of the plug, tests to establish surrounding rock stress regime, plug strength, and residual permeability are described to enable a comparison with original design assumptions. Monitoring and maintenance procedures are proposed to ensure satisfactory long-term performance of the plugs.

Jan 1, 2006

By I. A. Mwamba

Plain and alloyed titanium aluminides of composition Ti-47.5 at.% Al were prepared by melting commercial-purity titanium and aluminium with additions of 1 at.% precious metal. The as-cast alloys were subjected to potentiodynamic scans in 5, 15, and 25 wt% HCl aqueous solutions at room temperature and compared for their abilities to spontaneously passivate. Addition of precious metals resulted in a general improvement of corrosion resistance by increasing the open circuit potential to more noble values. Addition of 1 at.% gold or silver to titanium aluminide did not significantly increase the corrosion potential (Ecorr) above that of the plain titanium aluminide alloy, indicating that gold and silver are not sufficient cathodic modifiers to improve the corrosion resistance of titanium aluminide in all the solutions tested. However, platinum, palladium, and iridium additions shifted the corrosion potentials to the position of the passive region of plain TiAl for all solution concentrations. This indicated that TiAl alloyed with these platinum group metals would passivate spontaneously by cathodic modification. TiAl alloyed with palladium performed the best in 5 wt% HCl solution with the most positive corrosion potential. In 15 wt% HCl solution, alloys with platinum exhibited the most positive corrosion potentials, while alloying with iridium or palladium revealed more negative corrosion potentials. Thus, palladium alloying led to the best cathodic modification of titanium aluminide in low-concentration HCl solution, whereas platinum and iridium alloying additions resulted in the best cathodic modification of titanium aluminide in high-concentration HCl solutions.

Jan 1, 2013

By K. M. Godiwalla, S. Ranganathan

The thermal state in submerged-arc furnaces (S.A.F.) producing ferro alloys is important for the conditions of both the grade of alloy produced as well as specific energy consumption. The temperature profile in the S.A.F. is affected by the endothermic chemical reactions and the rate of gas evolution. The gas evolution commences at about 900 C due to the reduction of iron in the ore. A first-principle-based 2-D model has been developed to predict the temperature profile in the furnace. In this study, four ores of different grades have been considered in order to simulate the thermal profile in the S.A.F. The influence of the composition of the ore on the thermal profile and its significance in rationalisation of charge distribution to optimise the process are discussed.

Jan 1, 2007