Search Documents

By M. Jacobs

Keywords: Smelting, converting, sulphide, sulphide smelting, platinum, platinum group metals, PGM, base metals, nickel, copper, matte, slag, furnace, electric furnace, Söderberg, electrode, granulation, converter, flash drier, sulphuric acid, acid plant, Ausmelt, Sirosmelt, pyrometallurgy, metallurgy, Anglo Platinum, South Africa Waterval Smelter complex is situated in Rustenburg, in South Africa?s North West Province. The smelter objective is to process wet concentrate to produce crushed, slow-cooled, sulphur-deficient nickel-copper matte rich in platinum group metals (PGMs), gold, and base metals for despatch to the Magnetic Concentration Plant at the Base Metals Refinery. Throughout its history, the smelter complex has been continuously upgraded in line with increasing production demand, changing feeds, environmental initiatives, and advances in available technology. The smelter receives filter cake and slurry from Anglo Platinum concentrators and joint ventures. Wet concentrate is fed through a flash drying process utilising coal-fired, fluidised bed hot-gas generators, to produce dry feed material for the electric furnaces and slag-cleaning furnace. For primary smelting, two electric furnaces are used, each with a rated capacity of 34MW. Furnace matte, containing the bulk of the base metal sulphides and PGMs, is tapped periodically into refractory-lined ladles and granulated using high-pressure water jets, then dried through electrically powered pneumo-driers to become the main feed to the Anglo platinum Converting Process (ACP). Slag is tapped semi-continuously, granulated, and treated through the slag mill. The ACP treats the combined matte output of Waterval, Polokwane, and Mortimer smelters. It is a top-blown furnace, with furnace matte, air, and oxygen being injected into the converter via a lance submerged in the slag. Converter matte is tapped and bottom cast into moulds, slow-cooled, crushed, and despatched to the refineries. Slag is granulated and dried for recycling to the slag-cleaning furnace. ACP slag is fed to the slag-cleaning furnace along with a reductant and a sulphur source. Slag-cleaning-furnace matte is granulated for processing by the ACP, while slag is granulated and processed in the slag mill. The slag mill and flotation circuit treats granulated slag from the electric furnaces and slag-cleaning furnace to recover entrained matte containing valuable PGMs and base metal sulphides.

Jan 1, 2006

By G. Hangone

Paper written on project work carried out in partial fulfilment of MSc thesis This paper investigates the effects of thiol collectors: xanthates, dithiophosphates, dithiocarbamates and mixtures of these on the froth flotation performance obtained with a bornite-rich copper sulphide ore from Okiep Copper Mine with a feed grade of 1.8%copper. Batch flotation tests were used to assess the performance in terms of mass-water recovery, sulphur grade-recovery and copper grade-recovery relationships and the Klimpel rate constant for copper recovery. The results showed that the di-ethyl-dithiocar-bamate (di C2-DTC) was the weakest collector of copper sulphide minerals. Highest copper recoveries were obtained with the di-ethyl-dithiophosphate (di C2-DTP), which were accompanied with more watery froths and lower copper grades demonstrating frothing properties in addition to collector action. Superior copper recoveries were obtained with the 90% ethyl xanthate (C2-X):10% di-ethyl-dithiophosphate (di C2-DTP) and 90% ethyl xanthate (C2-X):10%di-ethyl-dithiocarbamate (di C2-DTC) collector mixtures compared to that obtained with ethyl xanthate at an equivalent collector dosage of 0.139 mol/ton ore (a dosage equivalent to 20 g sodium ethyl xanthate per ton ore). A superior copper grade was obtained with the 90% ethyl xanthate: 10% di-ethyl-dithiocarbamate collector mixture at a dosage of 0.0695 mol/ton ore compared to that obtained with ethyl xanthate at the same equivalent dosage. Keywords: flotation, collector mixtures, copper sulphide ore

Jan 1, 2005

By D. Bessinger, N. Rughubir

Exxaro Sands KZN produces?among other heavy mineral products?high titania slag, which is used as feedstock to the pigment industry. The titania slag is produced from the smelting of ilmenite in two 36 MW DC furnaces. In this smelting process carbon monoxide gas is produced. This gas is cooled, scrubbed and washed to remove entrained dust. This paper provides details on the gas cleaning plant system and the chemistry, mineralogy and size distribution of the particulate material contained in the off-gas stream. Characterization of the dust shows that is consists mainly of ilmenite, but with relatively high levels of SiO2and MnO. Smelting of the dust in a 500 kW DC furnace was carried out to investigate the potential for recovering valuable elements from the dust.

Jan 1, 2007

By S. Lubbe

South Africa and Australia are the biggest suppliers of zircon sand to the international zirconium industry. However neither South Africa nor Australia is well known for zircon beneficiation. Geratech Zirconium Beneficiation Ltd (GZB) continued with additional research on sodium hydroxide (NaOH) cracking of zircon sand during 2002-2003. In 2003 GZB started extracting zirconium from zircon sand by means of NaOH cracking on a commercial scale. Experience has shown that temperature profile and atmospheric control inside the furnace is crucial for the beneficiation of zircon sand. Silica carryover to zirconium chemicals could result if a high temperature is used. Once the sodium silicate is extracted from the sodium zirconate and dissolved in hydrochloric acid, two distinct routes can be followed to precipitate various zirconium chemicals. The most common route is to precipitate zirconium oxychloride crystals (ZOC), with subsequent purification from all contaminants (crystal route). Less known is the process (liquid route) that involves the direct precipitation of zirconium basic sulphate (ZBS). This route will yield a less pure product, with contaminants such as silica and titanium. An important factor in this route is the prevention of silica gel formation, which could hamper final product filtration. For applications like paint drying (zirconium octoate) or antiperspirants (zirconium hydroxychloride) low levels of contaminants have no effect on the final product. The advantage of the liquid route is fewer production stages compared to the crystal route. The disadvantage of the liquid route is that the market for the products will be significantly smaller. The optimum solution could be a plant design that could cater for both routes. Another example of an application of zirconium chemicals is the use of ammonium zirconium carbonate (AZC) in the paper industry. Zirconium basic carbonate (ZBC) is dissolved in ammonium carbonate to produce AZC solution. AZC is used mainly in European countries in the paper industry. For example, carton boxes were initially produced with formaldehyde as the binder, however, it has now been replaced with AZC since formaldehyde is considered toxic. AZC reacts with the cellulose fibres in the paper to act as the binder. The resulting product is not toxic, and printing ink dries very quickly due to the porous paper structure. Other applications of zirconium chemicals involve the use of acid zirconium sulphate tetrahydrate (AZST), zirconium orthosulphate (ZOS), potassium zirconium carbonate (KZC), and zirconium hydrous oxide (ZHO). Fluoride-based zirconium chemicals like zirconium tetra-fluoride (ZrF4) and hexafluoro-zirconic acid (H2ZrF6) are used in the aluminium industry. Zirconium oxide (Zr02) can be produced from any of the abovementioned precipitated chemicals via a high-temperature decomposition process. The physical properties of such oxides can differ tremendously, depending on the final application. The fired density of sanitaryware is typically 5.8 g/cm3, compared to milling media at >6.1 g/cm3. The required fired density is achieved by controlling the precipitation and decomposition conditions for these two oxides. The same applies to stabilized and mixed oxides, for example where zirconium oxide acts as an oxygen carrier in fuel cells.

Jan 1, 2012

By M. Kirsten, W. H. Botha, M. H. Fox, J. A. Moolman, A. J. Lathwood

Water is a valuable and in many areas a scarce resource. Governmental legislation regulates the environmental impact of water usage and wastewater disposal through the issue of licenses. These requirements mean that hydrometallurgical refineries must ensure that water consumption and water disposal is managed on a continuous basis in order to prevent the repeal of their operating license. Water balances are often overlooked during the design of a hydrometallurgical refinery. Recent changes in environmental legislation have forced both design engineers and operational management to review water use and disposal within these processes. Unlike concentrators where water can easily be recovered by recycling from tailing dams, water introduced into hydrometallurgical refineries becomes contaminated with soluble metals and thus requires pre-treatment prior to disposal. This paper discusses the various concerns that need to be considered during design and operation of hydrometallurgical refineries with respect to the water balance.

Jan 1, 2007

By G. Broadbent

It is an honour to be invited as a speaker to this ICCR conference and a pleasure to be with you here in South Africa. I have been asked to talk about the competitiveness of coal versus other energy alternatives. Coal supplies nearly one-quarter of the global primary energy. Its most direct competitors are gas, nuclear and renewables. Oil is predominantly for transport fuels. Fuel oil is competitive with coal when crude is below its long-run average price and has some niche opportunities. But I will confine my comments to nuclear, renewables and particularly natural gas as the most potent current competitive threat to coal. Competitiveness is more than just cost and price; there is environmental acceptability, security or reliability and increasingly image. These factors are more of a spectrum than discrete issues. Dollars and cents remain the key issue for competitiveness but one must recognize the impact of politics in sustainable development and energy security.

Jan 1, 2001

Stope support systems, typically consisting of props and packs, are used extensively in the gold and platinum mining industry to stabilize the rock mass in the excavation vicinity and to reduce the hazard associated with rockfalls and rockbursts. The design of stope support systems was historically based predominantly on past experience and practices, and cost considerations. The recent development of a new and improved support design methodology, has led to the potential for significant increases in worker safety and support cost savings. This paper reviews some of the fundamental rock mass and support criteria that form the basis of the improved support design methodology. The considered design criteria are the height of potential fall; quasi-static stope closure rates; dynamic stope closure rates; compressive hangingwall stresses; discontinuity spacing, orientation and interface properties; effect of support length (stoping width); effect of compression rate; consistency of support performance; a real coverage; support spacing; and zone of support influence. The proposed support design methodology combines both the zone of influence and key block stability theories, resulting in optimized support systems for rockfall and rockburst conditions. The site-specific methodology consists of two stages: (i) a tributary area analysis, and (ii) a zone of support influence and a stability analysis, considering hangingwall failure due to buckling, shear and block rotation, which gives maximum safe spacing of individual support units. The methodology is suitable for designing support systems for both blocky hangingwalls and hangingwalls fragmented by face-parallel extension and shear fractures.

Jan 1, 2001

By P. Altounyan

Techniques used to safely control the roof in UK coal mines for some 10 years have been applied to a South African coal mine. This new approach known in the UK as advanced rockbolting technology, is based on applying four fundamental principles: ?Understanding the roof failure mechanisms ?Using an effective roof support system ?Designing this support using measurement ?Monitoring the performance of the system. The paper summarizes the approach in detail and describes how it is being applied by Anglo Coal, giving results obtained to date. Investigations at a number of South African coal mines, including stress measurements at two Anglo Coal mines, have confirmed that the mode of roof failure (lateral shearing due to horizontal stress) is the same as in other coalfields worldwide, and aspects of current world best practice, including the use of advanced technology rockbolting, are therefore relevant in South Africa. The stress measurements indicated a high level of stress field anisotropy and further investigation of stress conditions in South African coal mines is recommended. The most effective bolting system to resist shear failure is one with high bond strength and stiffness. Short encapsulation pull testing of existing South African systems confirmed that they have low bond strength and stiffness. An improved rockbolt system with the required performance, and features allowing rapid installation and installation quality and performance audit, has been developed and is currently under full-scale trial. Design by measurement and routine monitoring procedures including the use of a rotary telltale device are also under trial. It is anticipated that South African coal mines will be able to obtain significant safety and productivity benefits from the application of this technology.

Jan 1, 2001

By R. J. Davidson, M. V. Nkosi, V. Veronsee

When activated carbon is used for the recovery of gold and silver from Witwatersrand gold-plant solutions, severe fouling of the carbon by calcium carbonate is experienced. Also, difficulty is encountered in the retention of the adsorbed silver on the carbon because it is displaced by gold. The acidification of plant pregnant solutions before they are contacted with carbon was therefore investigated as a means of overcoming these shortcomings. The results from batch laboratory experiments on the effect of pH on gold adsorption from plant solutions and from synthetic solutions of high ionic strength indicated reaction rate optima in the region of pH 5 and below pH I. The effect of pH on the equilibrium capacity constant for gold adsorption onto activated carbon was also studied, using both a plant solution and a synthetic solution of high ionic strength. In the case of the plant solution, the results suggested only a marginal change in carbon capacity for gold in the pH range 12 to 6, with significant increases in capacity at lower pH values. In the case of the synthetic solution of high ionic strength, the capacity constant was found to increase steadily as the pH was lowered from 12 to I. It was also found that the gold adsorption capacity of the carbon was significantly better for the synthetic solution. No precipitation of gold from the pregnant solution (gold content approximately 6 g/t) was noted as the pH was decreased to values as low as ,. However, about 25 per cent of the 0,6 g/t silver content was found to have precipitated when a pH value of 3,0 was attained. Further substantial precipitation of silver took place as the pH was lowered further. The investigation was extended by the passing of suitably acidified gold-plant solutions through one or more columns containing activated carbon. Preliminary results showed that the particle size of the carbon had a significant effect on the rate of gold adsorption. No displacement of adsorbed silver by gold was observed to take place at an influent pH of 5. In a typical continuous 'merry-go-round' operation involving three columns in which gold was eluted from the lead column every 48 hours, effluent values averaging 0,001 g/t gold could be consistently achieved under simulated plant-operating conditions. The results were obtained at relatively high velocities of influent solution, resulting in very little hold-up of gold in the carbon-recovery circuit. More than 99,9 per cent of the gold and more than 99,8 per cent of the silver was recovered in the adsorption circuit, while the elution data indicated an average elution recovery of 99,8 per cent of the adsorbed gold and 98,2 per cent of the adsorbed silver. Elution of the carbon was carried out at 91 QC. This involved pretreatment of the carbon with a sodium cyanide solution, followed by elution with deionized water. At a loading flowrate of 66 bed volumes per hour, the indicated take-up of metals on the carbon in the lead column was as follows; 53 k g/t gold, 6 k g/t silver, 57 k g/t copper, 14 k g/t nickel, and I k g/t zinc. Only a trace of cobalt was adsorbed. At an elution rate of 1,7 bed volumes per hour, the lead column was found to be completely stripped in under 5 hours, with concentrations of gold in the eluate reaching 6 to 7 g/l. Besides the excellent adsorption and elution results obtained when acidified pregnant solution was used, no fouling of the carbon was indicated, and the pressure drop across the three columns was considered to be well within practical limits. When compared with conventional zinc precipitation, the carbon process would appear to have considerable economic merit, with strong indications that significant savings would be possible both in capital and operating costs. Further pilot-plant experiments, preferably on a gold plant, would be required before a meaningful cost comparison could be made with the existing process.

Jan 1, 1979

By C Katongo

Ground condition at No1. Shaft varies across the mine. The different ground conditions arise as a result of the differences in the rock strength and structure, seismicity and induced stresses in abutments areas. Apart from being a major cause of Fall of Ground incidents/accidents, adverse ground conditions where encountered has affected the rate of development advance as well as production. This implies that for support to be cost effective Geotechnical section has to ensure that support is designed to prevailing ground demand to ensure the safety of personnel and minimize loss of production. We have also seen changes in mining methods as a result of change in ground conditions. To avoid incurring unnecessary costs through remedial works resulting from ground deterioration and collapses of development openings due to inadequate support, the principle in engineering design is ?Do it right the First Time?, and this can only be achieved through good understanding of Geotechnical environment. The paper discusses the different ground conditions encountered in various development ends at No.1 Shaft. It also discusses the principles of ground support, failure mechanisms, types of ground support systems employed, and the different techniques used to select support systems, and quality control techniques in underground support installation.

Jan 1, 2005

By F. C. Harvey

The Annual General Meeting of the Orange Free State Branch was held on Wednesday evening, 30th July, 1986, in the VIP Lounge of the Freegold North Region Canteen. The meeting was well attended, a total of 73 members, guests, and visitors being present. It was extremely pleasing to have such a large number of lady visitors present.

Jan 1, 1986

By Pentti Niskanen

"The ventilation system of the Pyhasalmi Mine is described. The mine is located in an area where the annual atmospheric temperature may vary from +30°C to -30°C. Natural ventilation causes serious difficulties because the underground mine is connected by drifts and finger raises to the bottom of the 120 m-deep open pit.The natural ventilation tends to make the ventilation net unstable. The paper describes how the instability characteristics of the ventilation net can be studied and how they have been taken into account when automating the control of the ventilation. In addition, the software, hardware and costs of the system are described. The system consists of 12 automated ventilation doors, two mine fans, 8 elements for sensing the air flow and temperatures, a control panel and a process computer."

Jan 1, 2014

By H. P. Kritzinger, T. C. Kingsley

Rotary kilns are used for a variety of mineral processing operations. Hatch makes use of a kiln model developed from first principles to evaluate designs for its clients. This tool has been applied to a variety of pyrometallurgical applications. This paper illustrates the application of numerical optimization techniques in combination with the kiln model in the interrogation of a generic iron-ore reduction process. The fundamental modelling concepts are explained, followed by a description of the optimization approach. The results show how the combination of the two methods, with modern computing power, can generate a large number of viable design and operating candidates.

Jan 1, 2014

By J. A. L. Napier

An analytical solution to the best choice of cutoff grade for a mine is deduced for an assumed model of selective mining. It is found that this choice is determined by the constancy of a special function, the Hamiltonian, over the life of the mine. It is suggested that the appropriate constant value for this function should be determined by the expected long-term average of the paylimit. In that case, the optimum profile can be calculated at each point in time according to the prevailing working cost and product price. In particular, a decision can be made between operation at the true paylimit or at the subsidized paylimit implied by either the lease and tax formulas or the assistance formula for gold mines. It is also shown how the basic formulation can be extended for 'use in the determination of the optimum joint paylimit for two products over the life of the mine.

Jan 1, 1983

1. OPLEIDING IN INGENIEURSWERK VIR IN G ENIEURS- IN -OPLEID IN G 1.1 llegistrasie as Ingenieur-in-opleiding 'n Gegradueerde ingenieur wat in 'n eksamen geslaag het wat die Raad erkenl, is registreerpaar as 'n ingenieur-in-opleiding kragtens die Wet op Professionele Ingenieurs2. Aansoekvorms kan van die Registrateur verkry word. Mineral processing congress The XIIIth International Mineral Processing Congress is to be held in Warsaw from 4th to 9th June, 1979. Seeing that by products and co-products are becoming of increasing importance in mineral processing operations, the theme of the Congress is to be the 'Treatment of Raw Materials with Total Utilization of All Constituents'.

Jan 1, 1979

By M. D. Budeba

Determining the efficiency of a surface coal mine operation is an essential activity, which can help in deciding on the optimal use of input resources, including effective capital allocation, in generating a desired quantity of coal of a specific quality. Mines operate today in challenging conditions, with diminishing reserves of high-quality coal, remote location of new coal deposits, infrastructure problems, environmental legislation, and the effects of climate. All these have an impact on the performance of a mine. Given such challenges, a company has to be technically efficient compared to other existing coal producers in order to generate profits. It can use the measurement of its efficiency to evaluate its productivity, benchmarking this against the best-performing mines and determining optimal variables in order to minimize slack and achieve the desired outputs. This paper discusses the use of Data Envelopment Analysis (DEA) in evaluating the efficiency of a surface coal mine supply chain for the coal export market. The supply chain is considered to be composed of subprocesses that are modelled as a multistage system. Numeric examples will be used to illustrate the application of DEA.

Jan 1, 2014

By More-O&apos, R. C. Ferrall, J. W. Wilson

Discussion: M. D. G. Salamon* (Fellow): The theoretical principles behind the techniques of calculation used by the authors was formulated and published during the period 1962- 65. These principles, together with their practical implications, were summarized in a review paper in 1966.1 Now, in February, 1970, we have this long and comprehensive paper discussing the practical application of the theory. I think this is good progress. The large number of practical examples treated in the paper clearly demonstrates not only the skill and knowledge of the authors, but also the versatility of the techniques of analysis. I feel that the techniques described by the authors, and their improved versions, will revolutionize mine planning. I suggest that no shaft system or stoping layout should be planned in future without an adequate rock mechanics analysis. It seems that it will be progressively more difficult to white wash mistakes in rock mechanics and attribute their costly outcome to normal mining risk. We should not, however, become complacent. There is still a lot to learn and do in the future. I do not want to discuss tonight the question of further research but instead, I will raise two other problems which may hinder the future progress of practical rock mechanics. To carry out work similar to that described in the paper, mine managements require men who are capable of doing the work and who have the most efficient techniques of analysis at their disposal. As a research engineer I have been associated with the development of techniques of analysis. I can assure you that these have undergone an amazingly rapid development during the last six years. We have seen the change from the use of the electrolytic tank analogue and manual integration to the method described by the authors, that is, to the employment of the automatic network analogue and computer integration. But this is not the end. In a recent paper Prof R. P. Plewman2 and his co-authors described a completely digital technique. Here the process of calculating on- and off-reef quantities is integrated into one computer run. But these sophisticated methods of computation are useless without men to make intelligent use of them. During the last few years a new breed of mining engineers has appeared on the scene - the Rock Mechanics Engineer. I feel it is timely to call the attention of the senior members of this Institute to the fact that this new breed will succeed in carrying out its duties in a valuable manner only if we manage to attract to its ranks young engineers of the right quality. The requirements are high. The top rock mechanics engineers have to be good mine planners and they have to understand the essence of sophisticated theories. Without these attributes they will not succeed in the long term and the industry will not gain the benefit of available knowledge. To attract this quality of engineers the industry will have to ensure that rock mechanics is accepted by all concerned as a career which could lead to the top echelons of our profession. Finally, I would like to make one or two remarks concerning Part I of the paper. In Sections 3.1 and 3.2 the authors describe methods of determining the normal stress on the reef plane and the convergence distribution in the excavations. The description as given applies only to a horizontal reef. When the reef is inclined the situation is more complex since a shear component of stress on the intact reef and a ride component in the excavations must then also be determined. These can be calculated by methods similar to that described in the paper.3 The practical application of the method of calculating the released energy (Section 3.4) is in the comparison of various stoping layouts to establish an order of preference in terms of decreasing rates of energy release. To carry out these comparisons effectively, the calculations must be carried out in a manner by which the values of energy per unit area obtained are comparable. I would like to note in this respect that the method of calculation given in the paper is valid without reservation only if there is no elastic contact between the hanging and foot walls in the mined-out area. If there is contact then the calculated energy values are correct only if the mined out area is increased in small steps during the analysis. My second point in this regard is concerned with the practical method of calculation as described in Sections 3.4 (ii)-(iii). Firstly, I would like to suggest that the energy calculation should be carried out, as far as possible, by using always the same scale on the analogue. Secondly, the reading of current on a pin should be followed by the removal of that pin to obtain the corresponding reading of potential. The product of these two values will be proportional to the energy released during the mining of the small area corresponding to that pin. The method suggested by the authors tends to mask possible danger points in the layouts, since they obtain an average value for a time period, say, for six months.

By J. Preussner, U. Glatzel, R. Völkl, S. Prins, M. Wenderoth

Platinum base alloys are very corrosion resistant and have got a high melting point. Similar to Ni-base superalloys, which are used for jet turbines, the hardening effect of the intermetallic L12Pt3Al phase is used to receive a material that is creep resistant at high temperatures. Chromium is added to the alloy system to stabilize the L12phase down to room temperature. With the right amount of nickel the misfit and shape of the precipitates can be controlled. Various alloy compositions have been melted and analysed. With scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) a microstructure can be observed, which is very similar to the one in Ni-base superalloys. To support alloy development with simulations, a thermodynamic database of the Pt-Al-Cr-Ni system is about to be established. The SEM and EDS measurements provide useful input to the thermodynamic optimization. Also many data from the literature have been used to receive the best approximation. The Cr-Pt binary phase diagram has been reassessed and the latest results of thermodynamic modelling are presented.

Jan 1, 2006

By R. E. Wilmot

This paper is based on the experiences, over many years, of numerous authors in the South African mining industry and of the hot dip galvanizing process and its application as a corrosion protection system. The paper sets out the extensive development, financial resources and stringent operating requirements of the South African mining industry. After many years of research and operational experiences, hot dip galvanizing and, when necessary, duplex systems, have been found to meet the demanding requirements of this particular industry. The paper sets out the requirements from the standpoint of corrosion criteria and is followed with a case where the corrosion protection properties of hot dip galvanizing are demonstrated. This case history traces the early investigation of the expected corrosive conditions in a new mining operation and concludes with two follow-up visits to the mine in order to examine actual performance of the corrosion protection system after ten years in service.

Jan 1, 2007

By M. J. Nicol

On page 51, the equation numbered.... On page 52, the equation numbered .... On page 53, the arrangement of the equation.... Canadian reports Asbestos by G.O. Vagt.l0 pp. Chromium by D. G. Law-West. 6 pp. Iron and Steel by T. R. Mclnnis. 15 pp. Titanium and Titanium Dioxide by M. A. Boucher. 7 pp. Vanadium by D. Shaw. 7 pp.

Jan 1, 1984