Search Documents

By W. J. Fene

The lowest number of fatalities from coal-mine explosions in the United States in any year since records have been kept was the total of 8 in 1949 and again in 1950. Even incomplete records as far back as 1870 reveal a larger annual loss of life from explosions. From 1890 to 1948 the lowest annual loss was 32 in 1946. A smaller total of 15 fatalities was reported in 1952. Figure 1 shows the total yearly loss of life from explosions in all coal mines since 1880. Those in anthracite mines alone are shown by the shaded area. The erratic variation of the chart line shows the difficulties that have confronted the industry in the struggle to control and eliminate mine explosions. Potential hazards have existed in marry mines without realization that only a small change in conditions could initiate a disaster. Many disasters causing great loss of life occurred in mines that had been regularly operated without incident for long periods. Although the number of coal-mine explosions causing great lose of life has been kept down in recent years, the exceptions still make the record anything but satis¬factory. There have been almost no widespread explosions for several years, but in a few instances many lives were lost from afterdamp. Although the violence and spread of mine explosions may be controlled, the loss of life may be heavy if many of the men happen to be in the path of the smoke and gases. For these reasons, the strictest controls must be maintained to eliminate all factors that might combine to cause even a small ignition of gas or dust.

Jan 1, 1953

By E. P. Youngman

This paper is one of a series of digests of foreign mining legislation and court decisions that is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the mining laws of British Honduras has been prepared from the best available information in Washington and is released subject to amplification or correction, if necessary, by United States foreign-service officers. INTRODUCTION The mining law governing all mineral substances other than oil is ordinance No. 7 of 1927 (Minerals Ordinance, 1927), passed by the Legislative Council on March 25, 1927. The accompanying regulations, No. 3 of 1932 (General Minerals Regulations, 1932), made under the authority of section 66 of the minerals ordinance, were made by the Governor in Council on December 23, 1931.

Jan 1, 1934

By Donald F. Smith

This report describes the construction and calibration of two ice calorimeters and includes results of high-temperature heat-content measurements, made by the Federal Bureau of Mines, on rubidium fluoride, hafnium tetrafluoride, cesium chloride, and cesium iodide. The heats and entropies of fusion of rubidium fluoride, cesium chloride, and cesium iodide have been calculated at their respective melting points using equations derived from the experimental heat-content data. Hafnium tetrafluoride did not melt within the range of temperatures investigated. Heat and entropy of transition of cesium chloride from the alpha to the beta form were also determined. INTRODUCTION Free-energy data usually afford the cheapest and quickest means of determining the feasibility of experimentally untested reactions. For known reactions, free-energy data show the variation of the equilibrium constant with temperature and make it possible to calculate, without experiment, the maximum ratio of product to raw material for a given chemical process.

Jan 1, 1961

By Richard L. Unger

Equipment is the primary cause of injury in 11% of all mining accidents and a secondary cause in another 10%. Purchasers should select new equipment carefully to ensure that the machine incorporates good ergonomic design criteria that maximize the safety of their mine workers. One potential problem area is the workstation-the control center of the machine. Safety problems often occur when the workstation provides insufficient clearance or visibility to the operator or has controls that are difficult to reach. This is especially true for underground mines, where confined space is an issue. In reclined or stooped postures, operators will have less strength and agility and often experience reduced visibility. We have conducted and published much research in Human Factors design of mining machine workstations. This information is currently being compiled into a series of Human Factors design recommendation reports. The reposts dl cover many topics, including workstation layout, control design, seating, and visibility. Each topic has a list of basic or first principles of design. Understanding these principles is the key to designing or purchasing a workstation that is both safe and efficient. Following is a sampling of these main topics and first principles.

Aug 1, 1996

By L. B. Pankratz

Heat content measurements were conducted for GaPo.996 and InPo.986 over the temperature range from 298° to 1,100° K, and for In2S2.897 over the range from 298° to 1,200° K. Both the actual experimental data and values adjusted to conform with the stoichiometric compositions (GaP, InP, and In2S3) were reported. Entropy increments above 298.15° K were calculated for the stoichiometric compounds, and heat content and heat capacity equations were derived.

Jan 1, 1965

By Christopher Mark, Robert J. Tuchman

This proceedings volume contains papers presented at technology transfer seminars sponsored by the National Institute for Occupational Safety and Health (NIOSH) on New Technology for Ground Control in Retreat Mining. The seminars were conducted at five locations: Uniontown, PA (March 26, 1997), Norton, VA (April 8, 1997), Pikeville, KY (April 10, 1997), Charleston, WV (April 17, 1997), and Evansville, IN (April 22, 1997). The papers presented here describe several new, highly practical technologies developed by the NIOSH Pittsburgh and Spokane Research Centers3 to improve safety during pillar retreat operations. Two central issues are addressed: pillar design and mobile roof supports (MRS's). Proper pillar sizing is essential for safe pillar extraction. The Analysis of Retreat Mining Pillar Stability (ARMPS) program and its large data base of actual mining case histories are presented. LAMODEL, a second computer program, can be used for analysis of multiple-seam and other complex mining situations. Other papers address pillar design to avoid massive pillar collapses and the proper role of coal strength testing. MRS's have greatly improved safety where they are used for pillar line support. We studied the application of MRS's at 20 mines throughout the Eastern United States. Conclusions regarding the most effective section layouts, cut sequences, and support placements are reported. Field and laboratory tests of MRS's are also described.

Jan 1, 1997

By James P. McGee

Preliminary calculations show an economic advantage in using nuclear energy to supply the endothermic heat required for gasifying coal. It should be noted that the various assumptions used in preparing these calculations must undergo further evaluation through additional engineering design and research. The proposed system for gasification is the indirect process cycle with helium heated in a nuclear reactor and passed through an exchanger-type gasifier for the reaction of coal and steam to form CO (carbon monoxide) and H2 (hydrogen gas).

Jan 1, 1960

By Robert F. Chaiken

A quasi-steady-burning channel model is used in this Bureau of Mines study to describe the conductive heat loss from an in situ coal combustor to the surrounding rock strata. The calculated heat losses are significantly greater than those previously estimated, but are still very acceptable from the viewpoint of energy recovery. Approximately 80% to 90% of the heat of combustion of the coal should appear as sensible heat of the gaseous exhaust, with exhaust temperatures in the range of 1,000° to 1,200° C. The effects of burning stoichiometry and channel size on the heat loss are also discussed in terms of the model. Such effects are shown to be compatible with an in situ combustion process even in thin seams. However, these results depend on gas leakage and adverse roof falls not being important factors in deter-mining the heat loss mechanism.

Jan 1, 1977

By Alan H. Goode

Glass wool meeting requirements for commercial use was made from glassy fractions of urban solid wastes by the Bureau of Mines. This research was a part of the Bureau's program to develop building products and other usable materials from reclaimed urban waste materials. Mixes of molten glass were fiberized into glass wool during laboratory studies by impingement of a jet of compressed air on a stream of the molten glass. The principal test variable studied was composition of the melt; this was varied by adding dolomite and alumina to obtain molten glass with the handling characteristics required for producing final wool products of the desired composition and physical characteristics. When no charge is made for the waste glass and approximately $75 per ton can be obtained for the wool product, an interest rate of return on investment after taxes of about 12 percent can be obtained. If a charge of $5 per ton is required for the waste glass, a selling price of about $78 per ton would be necessary to obtain a l2-percent-interest rate of return on investment after taxes.

Jan 1, 1972

By B. Dimitriades

Experimental work has been done to refine and to confirm an analytical procedure by which gas-liquid chromatographic (GLC) spectra are interpreted from retention time data alone. The rationale of this spectra interpretation technique involves whether or not a given peak invariably represents the same component or component mixture; if not, what factors influence changes in peak identifications. To answer these questions, peak-identification procedures, based mainly on the use of subtractive columns, were developed and applied to interpret GLC spectra of several exhaust (and fuel) samples.

Jan 1, 1972

By Donald P. Blasko

The Bureau of Mines investigated two areas of the Alaska Peninsula (Iniskin Peninsula and Becharof Lake) where oil and gas seeps were known to occur in an attempt to determine (1) whether the seeps are still active and (2) the amount of bitumen contained in the drainage leaving the seeps. The oil, water, oil-water, and gas were sampled and analyzed. Five oil samples were taken at four separate oil seeps. The API gravity of the oil ranged from 8.90 to 21.4° and the sulfur content was from 0.12 percent to 0.59 percent. Four of the seven gas samples obtained revealed fair high caloric values, ranging from 746 to 924 Btu/cu ft, and averaging 844 Btu/cu ft. A total of 44 water samples were obtained. Bitumen content of the water was as high as 9,773 mg/l at one seep, but averaged less than I mg/l where the seep-drainage water entered the Gulf of Alaska.

Jan 1, 1976

By L. W. Kelly

The primary purpose of this paper is to show the appreciable savings that were made by roof-bolting the main west entry of the Kings mine, which was to be the permanent, main haulage road, as compared to the cost of supporting the same roof with peg timbering as first planned. Additional items that might prove valuable to other mine operators are contained in this paper and detailed below. 1. A detailed cost of the system of roof support known locally as the peg-timbering method is given. It consists fundamentally of supporting steel cross bars on pegs inserted into holes drilled in the ribs close to the roof. 2. A method of supporting the roof in caved entries is shown, where such support must endure for an extended period in haulageways and air courses.

Jan 1, 1952

As part of the overall development of a borehole mining system -develop backfilling techniques to reduce possible damage to the environment caused by either the cavities or the piles of sand tailings that result from in-borehole hydraulic mining. (Borehole mining is described in technology News No. 56.) Approach Water filled cavities at the bottom of boreholes are rapidly and economically backfilled by jetting a sand-tailings slurry underwater. How It Works The Bureau of Mines borehole mining system creates a cavity having a horizontal diameter of more than 50 feet. (See photograph). This cavity can be backfilled with much of the sand previously mined. The sand tailings or similar backfill material is dumped by a front end loader into a slurry mixing tank at the rate of about one ton every three minutes. Enough water is added to give a thick, but pumpable slurry. The slurry is pumped down the borehole through a string of 4-inch pipe to the cavity. After passing through a right elbow at the end of the pipe, the slurry is ejected through a nozzle. The resulting slurry jet emplaces the backfill at the outer wall of the cavity. To obtain an even distribution of fill in the cavity, the nozzle is slowly rotated. The nozzle and pipe assembly is supported from a turntable on the surface. See diagram.

Jan 1, 1981

By John N. Murphy

INTRODUCTION It's a pleasure to be with you and to share in this opening session for the 27th Annual Institute on Mining Health, Safety, and Research. As we come together today, I would like to reflect for just a moment on the past Institutes. Much of the progress in Mine Health and Safety has been the subject of presentations and discussions at the previous Institutes, either by identifying the issues, proposing techniques to overcome the problems, or presenting new findings to address important issues for the mining industry. May I extend our thanks and congratulations to VPI and to the planners and organizers of all of these Institutes for their important contributions to our mutual goals of improving mine health and safety. In the time available today, I would like to accomplish two objectives: 1. Provide my assessment of the current status of the Mining Health and Safety Research Program; and 2. Share with you the continuing need and direction for the Mining Health and Safety Research. MINE HEALTH AND SAFETY RESEARCH TODAY Mine Health and Safety Research was conducted formerly at four geographical locations within the USBM, specifically: Pittsburgh, Spokane, Twin Cities, and Denver. Although the Twin Cities and Denver Centers were closed, we have been successful in relocatingfmaintaining much of the core competencies to conduct a responsive, multidisciplinary Mine Health and Safety Research Program. The current staff at Pittsburgh and Spokane directed toward Health and Safety Research totals 397. This includes Lake Lynn Laboratory, about 60 miles southeast of Pittsburgh, where large-scale mine fire and explosion research is conducted. With the closures and transition we have worked to maintain the core competencies necessary to address Health and Safety issues. In some cases we have made arrangements to provide the requisite core competencies through external organizations. An example is the reassignment of the diesel particulate instrumentation capability from Twin Cities to Pittsburgh. In the case of diesel emission control, due to the cost of relocating laboratories and the lack of the appropriate skills at Pittsburgh or Spokane, the emission control laboratory is now being operated in Minneapolis through a contractual arrangement with the University of Minnesota.

By N. Kumar Kittusamy

By Walter Kawa

The hydrogenation of phenyl ether, benzyl ether, and phenyl sulfide in the presence of iron catalysts was studied by the Bureau of Mines to gain a better understanding of the role of iron catalysts in the hydrogenation of coal. The carbon-oxygen and carbon-sulfur bonds in these compounds may be similar to some of the carbon-oxygen and carbon-sulfur bonds in coal which react during the early stages of liquefaction by hydrogenation. Experiments were made in batch autoclaves for 4 hours; hydrogen was at a pressure of about 540 atmospheres. In the hydrogenation of phenyl ether at 400° C, metallic iron catalyzed both hydrogenolysis (splitting-hydrogenation) and nuclear hydrogenation (addition of hydrogen to aromatic rings) reactions, Products were principally benzene and cyclohexane. The activity of metallic iron was decreased by adding carbon monoxide or a reactive sulfur-containing organic compound. Ferrous sulfide catalyzed the conversion of phenyl ether to benzene, phenol, and small amounts of cyclohexane. Hydrogenolysis of benzyl ether was catalyzed by metallic iron and to a lesser extent, by ferrous sulfide at 250° C. No nuclear hydrogenation was observed with either catalyst. Conversion of phenyl sulfide to benzene was nearly quantitative in experiments made at 250° C with equimolar quantities of phenyl sulfide and metallic iron or iron as ferric oxide. Conversions of metallic iron and ferric oxide to ferrous sulfide were nearly stoichiometric. No reaction of phenyl sulfide occurred in the presence of ferric oxide and water, and very little occurred in the presence of metallic iron and water. Ferrous sulfide also catalyzed the hydrogenolysis of phenyl sulfide to benzene, but conversion was lower than in experiments with metallic iron or ferric oxide. The activity of ferrous sulfide was increased by adding water and decreased by adding hydrogen sulfide. The results of this study suggest that ferrous sulfide is an active form of iron when iron is used as a catalyst for the hydrogenation of coal.

Jan 1, 1963

By W. W. Adams

[The quantity of explosives sold in the United States in January, 1931, for domestic consumption, amounted to 368,100 kegs (9,202,510 pounds) of black blasting powder, 4,810;000 pounds of permissible explosives, and 16,533,000 pounds of high explosives other than permissible. These figures are based on reports received by the United States Bureau of Mines, Department of Commerce, from nearly all manufacturing companies, and include an estimate of sues by several companies that do not furnish monthly reports. Reports actually received from manufacturers shored sales of 365,977 kegs of black blasting powder (consisting of 220,892 kegs of granular powder and 145,085 kegs of pellet powder), 4,687,900 pounds of permissible explosives, and 15,498,152 pounds of high explosives other than permissible. Sales in January, 1931, were smaller than in January last year, the decreases being 14 per cent for black blasting powder, 19 per cent for permissible, and 17 per cent for high explosives other than permissible. Sales in January 1931 when compared with soles in December 1930, show increases for all three classes of explosives as follows: 2 per cent for block blasting powder, 16 per cent for permissible explosives, and 7 per cent for other high explosives. PERMISSIBLE EXPLOSIVES: Of the 4,687,900 hounds of permissible reported sold during January, 97 per cent was used for coal-mining operations, Including 32 per cent for anthracite mines and 65 per cent for bituminous mines. The following Staten were the largest users of permissible explosives daring January: Pennsylvania, West Virginia, Illinois, Alabama, Kentucky, Indiana, and Utah. Their combined sales represented 89 per cent of the entire sales reported for this class of explosives.]

Jan 1, 1931

By William Porter

Hand scaling is a physically demanding job and is responsible for numerous overexertion injuries in mining. This experiment studied rib scaling from an elevated bucket to examine force generation capabilities and electromyographic responses to a prying subtask. Subjects exerted force using two bars (steel and fiberglass) at five target heights. Work height significantly affected peak prying force during scaling activities with highest force capacity at the lowest level (p = 0.0188). Bar type did not affect force generation (p = 0.7843): However, use of the fiberglass bar required significantly more muscle activity to achieve the same force (p < 0.05). It was concluded that miners should scale points on the rock face that are below their knees, and reposition the bucket as often as necessary to do so. Additional research is needed to fully understand the impact of bar type on the physical demands of an entire scaling task.

Jan 1, 2006

By John D. Warne

"INTRODUCTION Initiated as a part of the Bureau of Mines program for development of strategic minerals for national defense, Investigation of the fluorspar deposits of the Northgate area was begun in June 1944 and completed in March l946. Mining Operations were active in the district during most of the period of investigation.The Fluorspar, Fluorine, and Camp Creek mines develop the two more promising vein systems known in the area, the Fluorspar group of claims covering one vein system and the Fluorine and Camp Creek groups the other. Figure 1 shows the location of the properties. The Fluorspar and Fluorine properties were operated (except during the winter months) by the Western Fluorspar Corp. The Camp Creek mine was operated during 1943 and 1944 by Kramer Mines, Inc.The properties were examined April 20 and again November 4 to 12, 1943, by C. R. Wilfley, a Bureau of Mines engineer, who recommended work to determine ore reserves and to serve as a guide for development. Investigations by the Bureau of Mines covered all three properties."

Aug 1, 1947

By W. R. Crane

Recent papers on support of roof and top rock in mines representing present practice in so far as it hits been described by engineers in all of the principal mining countries, cover a relatively aide range of topics. The papers abstracted herein include such subjects as the testing of materials of support, failure and movement of rock above workings, effect of excessive pressures on rock masses, axed the application in mines of timber, metal, concrete, packing, and filling support. It is not within the scope of this paper to present a logical and orderly discussion of the elements of support and their application to conditions influenced by the material worked or the method of mining. Only the essential facts of a paper appear in the abstracts, the idea being to give a fairly clear picture of the behavior of various types of support under brows conditions and to put into concise form important information concerning present practice, modifications of practice, and the trend toward new practice. With such valuable facts from others experience made readily available, it Is hoped that the engineer with particular and often trying problems may obtain suggestions that will be immediately helpful.

Jan 1, 1932