Search Documents

By Derek Caizergues, Hurman Eric

The principle of carbothermic reduction has been around for many years. In principle it is a simple process, yet with a multitude of problems. The temperature required to affect reduction is in the region of 2200ºC and results in aluminium oxy-carbide formation rather than metallic aluminium. From a thermodynamic point of view, reducing the temperatures of reaction which would suppress oxy-carbide formation would only be possible by lowering the total pressure of the system. A decrease in thermodynamic activity of product aluminium by dissolving it in another phase would also help preventing the formation of oxy-carbides and would also increase the yield of the reduction reaction. Thus experiments have been conducted at around 1700ºC to determine the possibility of carbothermic reduction of alumina under the presence of a metallic solvent. Total pressure of the system was reduced to around 30kPa and metallic nickel, iron, copper and tin were selected as the solvent. The highest recovery of aluminium was achieved with the nickel solvent followed by iron, copper and tin. This ranking for the first three was also in accord with the extent of negative deviation form ideality in the respective binary solutions of these solvents with aluminium. The tin-aluminium system displays positive deviation form ideality. The rate and extent of reduction was found to be highly dependent on temperature and pressure. The pseudo first order reaction rate was found to be applicable to the process in all the solvents used. Rate constants were calculated and it is also suggested that the reduction was controlled primarily by the chemical reaction rate.

Jan 1, 2003

By G. M. Wolfaardt, B. C. Qi

"From a lifecycle point of view, biologically digested sludge is a valuable product that should be reused if possible. In contrast to landfill and incineration, application of digested sludge comprises the recycling nutrients and organic matter and reflects the policy of resource conservation and sustainability in waste management. Sludge may be applied to agricultural land for further sludge treatment and improvement of the characteristics of the soil. The characteristics of sludge that affect its applicability for soil conditioning include moisture content, pathogens, nutrients and metals. In this paper, the use of solid anaerobic digestion sludge of the lignocellulosic residues to condition soil was investigated in regards to nutrient composition, water content/retention capacity, hygienic quality (contamination of pathogenic bacteria) and heavy metal adsorbing/releasing characteristics of the sludge.The digested sludge had approximately 44.5% free and immobilized water and 46.9% bound water. The water-holding capacity of the sludge was high. This was the first merit to apply the sludge to agriculture in dry areas. Secondly, the sludge was rich in macro-nutrients (N, P, K) and a series of micro-nutrients (Ca, Mg, Mn, Na, Fe, Cu, Zn, B). The water-soluble fractions of macro-nutrients in the sludge were found considerably low. This implied that the loss or leaching of the macro-nutrients from the anaerobic sludge to the aqueous environment be slow. The nutrients loss owing to leaching could be reduced. However, because of a lower macro-nutrient content of the anaerobic sludge, comparable to the chemical fertilizer, it is advisable that the anaerobic sludge be applied together with commercial fertilizer to the agriculture land. Thirdly, the anaerobic sludge had strong selective adsorption affinity for heavy metal ions; non-heavy metal ions such as K(I) and Ca(II) could be released easily from the sludge in a wide pH range, such as pH from 1.0 to 8.0. Since the metal toxicity to the environment mainly comes from the mobile heavy metal ions, the selectivity to adsorb heavy metal ions of the anaerobic sludge can be utilized to reduce the availability of heavy metal ions to plants and humans in aquatic environment. Fourthly, the anaerobic digestion under thermophilic conditions showed a promising disinfecting effect to the sludge, in contrast to the landfill digestion."

Jan 1, 2003

By P. Huang, D. W. Fuerstenau

Various factors that control the natural flotability of talc, including differences due to crystal face and edge effects, were delineated. For study of talc depression phenomena, dextrin was used as a model depressant. For the enhancement of talc flotation, dodecylammonium acetate (DDAA) was used as the collector. The interaction of DDAA with talc was assessed by flotation experiments and electrokinetic (zeta potential) measurements, from which the role of hydrophobic bonding can be demonstrated. The results presented in this paper provide useful information on how the crystal chemistry and surface chemistry control the electrical double layer, adsorption phenomena, wettability, and flotation behavior of talc in aqueous media.

Jan 1, 2003

By P. A. Harvey

Previous studies have reported that inorganic electrolytes can enhance floatability of coal. The research has shown that the enhancement, if any, is highly dependent on changes in solution pH, type of electrolyte, and electrolyte concentration. The reasons for this are still not clear. In this study the floatability of coal particles in mono and divalent salt solutions was investigated. The zeta potential and hydrophobicity of the coal was measured experimentally, and a modified Hallimond tube was used to determine the floatability of coal particles by single bubbles, where the collision efficiency was equal to unity. The experimental information was used in conjunction with the Hogg-Healy-Fuerstenau equation to quantify the electrical double layer interaction. It was found that for low electrolyte concentration (less than 0.1 M) solutions the flotation recovery of coal particles was less than that for distilled water, and decreased with increase in concentration. Conversely, at electrolyte concentrations above 0.1 M, flotation recovery increased with increasing concentration (Figure 1). Both of these results are consistent with previous observations, but are inconsistent with expectations when considering the possible influence of electrical double layer interaction. Modelling of the system indicates that the electrical double layer is compressed with increasing electrolyte concentration, resulting in an increase in flotation recovery due to a diminishing of the (electrical double layer) repulsion between the bubble and the coal particles. Moreover, for electrolyte concentrations above about 0.1 M the electrical double layer is completely depressed and would have little further influence, if any, on the flotation process. Therefore, the electrical double layer interaction is not the principal determining factor for the flotation of coal in electrolyte solutions.

Jan 1, 2003

By de Vaux. D.

Synthetic water with a calcium concentration of 80 ppm and 500 ppm was prepared and the flotation results obtained compared to a simple electrolyte in order to determine the effect water quality has on pentlandite and pyroxene surface alteration and, ultimately, floatability. During the study, the possible effect of interactions between the minerals investigated and Ca2+ ions in the presence of sodium isobutyl xanthate was studied at pH 6 and pH 9 by means of zeta potential determinations, microflotation tests and ToF-SIMS analysis. The results obtained have demonstrated that water quality does play a significant role in flotation recovery at the experimental conditions used.

Jan 1, 2003

By S. K. Kawatra, T. C. Eisele

"Coal-fired electrical power generation plants produce 56% of all the electricity in the U.S., burning approximately 860 million tons of coal annually. This results in the production of 58 million tons of fly-ash; 19 million tons of bottom ash and boiler slag, and 23 million tons of desulfurization sludge.s annually. These are a considerable disposal problem, and it would therefore be very valuable to be able to sell these residues and by-products as useful materials, rather than paying to dispose of them in landfills. However, utilization rates are currently very low, below 32% even for the most thoroughly commercialized combustion byproduct (fly-ash). This poor utilization rate is a result of the high impurity content of combustion byproducts, which makes them unsuitable for existing markets.Mineral processing techniques are useful for upgrading and utilizing combustion by-products. Fly-ash can be processed to remove unburned carbon, or utilized as a binder component in ore pelletization and agglomeration processes; bottom ash can be processed to produce certain aggregate grades; CO2 emissions can be sequestered using modified leaching techniques; and many scrubber sludge’s require processing before they can be used for producing gypsum products.The experiments described in this paper were carried out to study the application of mineral processing techniques to upgrading combustion by-products, particularly flue-gas scrubber sludge. A process was developed for upgrading unoxidized Flue-Gas Desulfurization (FGD) sludge’s by removing the primary impurity (unreacted limestone). A combination of hydrocycloning followed by froth flotation reduced the limestone concentration to as little as 1.7%, while recovering 66% of the sludge weight as a clean product. The recovered limestone was sufficiently concentrated that it could be recycled to the scrubber for more complete utilization."

Jan 1, 2003

By James Y. Oldshue

"Very seldom is it possible when contacting a gas with a slurry to measure the dissolved gas concentration in the slurry, and even were it possible, seldom are equilibrium data available with a suitable Henry’s law constant.In general, by assuming a reasonable value for the dissolved gas concentration in the slurry and a corresponding equilibrium gas partial pressure P*, Kga values can be calculated for the pilot plant and scaled up. Then, with the same P* value at various reaction conditions, a mixer can be designed which is quite satisfactory, having a reasonable design factor for full-scale performance.We will take as an example a slurry of a known solids composition and use a continuous 4 tank system. By assuming a percentage saturation of the dissolved gas in the first tank, the dissolved gas concentration can be obtained in the other three tanks. It usually is possible to measure the off-gas composition in each of the 4 tanks. If the top of the tanks is connected in the form of a multi-compartmented horizontal autoclave, then a modified top off-gas composition in each compartment must be used."

Jan 1, 2003

By Jiang Wenli, Zhang Yimin

In order to enhance the quality of iron concentrate from magnetic separation, reverse-flotation technology is often applied in an iron ore dressing plant.However, this technology has disadvantages in terms of operating cost,energy consumptionand environmental protection(Zhao, Wu& Wang,2005).Developing innovative equipment to process magnetite ore more-effectively is a way to get rid of these disadvantages of reverse flotation and improve the quality of iron concentrate.This paper describes the development of Complex Flashing-Field Magnetic Cleaner,a new kind of equipment based on the principle of combination of separation in magnetic field and separation in gravity field(Hao & Jiang, 2002).This innovative equipment possesses a tailor-made magnetic system and has the characteristics of a magneticfieldwhich can strengthen the formation of magnetic agglomerations and the dispersion of gangue mineralsto improvethe quality of separation.The automatic control system developed specifically for this equipment can further increase the accuracy of separation and stabilize the process.

Jan 1, 2014

By Yimin Zhu, Dezhou Wei, Haijun Liang, Zhifu Zhou

It has been fairly well established by many experiments that Thiobacillus ferrooxidans (T. ferrooxidans), also named Acidithiobacillus ferrooxidans(Kelly and Wood, 2000),can depress the floatability of pyrite. However, the mechanisms governing the process have not been known completely. In the present investigation, wettability and electrokinetic studies were carried out to examine the surface chemical changes on pyrite before and after interaction with T. ferrooxidans or its secretions. Attachment of T. ferrooxidans to pyrite was observed using a scanning electron microscope. The results of experiments showed that, under certain conditions, T. ferrooxidans and its secretions would obviously change the surface electricity of pyrite and result in the iso-electric point of pyrite shifting notably. However, the surface wettability of pyrite hardly changed and its hydrophobicity increased little after interaction with T. ferrooxidans and its secretions. Based on the results of the present investigation it can be reasoned that the depression of floatability of pyrite is due to the reduction of surface free energy, rather than the increase of surface hydrophilicity of pyrite. The decrease of surface free energy weakens the attachment of collector to pyrite; during the process bacterial protein plays the most important role and the bacterial chemotaxis strengthens the effect.

Jan 1, 2003

By P. M. Solozhenkin

On the territory Sakha (Yakutia) are located largest in Russian Federation reserves of antimony ores, Sarylakhsk and Sentochansk deposits, amaunt 10% of world stocks of antimony. A processing gold antimony ores Sarylakhsk deposit is carried out on gravitation-flotation circuit to receive gold gravitation concentrate and gold-antimony flotation concentrate with the contents of antimony over 60%. The gold-bearing concentrate is treated on place hydrometallurgicaly to a high-standard product, accepted by gold bank cash department. At the ore dressing plant reached the highest recovery in world in a concentrate of antimony 90%~91.6%, and gold 85.7%~86.0% as a result of scientific research works. Studied the mechanism of interaction cations of metals Pb2+, Cu2+, Cd2+, Hg2+, Ag+ with a surface antimonite presented on the basis of modern physical-chemical methods: nuclear quadrupol resonance, x-ray electron spectroscopy, electron spin resonance. The industrial tests of sodium dimethyldithiocarbate were carried out which confirmed high recovery of Sb and As. The leaching Sb2S3 by bacteria Desulfovibro desulfuricans and transformation antimonite in antimony trioxide by Tiobacillus Ferrooxidans improved following cyanidation . The extraction of antimony in a solution 96.0%~98.0% under optimal conditions. The common total extraction in the appropriate commodity products for gold reached 98%, for Sb 96.5%. At a combination of bioprocessing and cyanidation 85.5% of extraction Au was achieved. The new solvents for antimonite were found. Now by the Close Joint-Stock Co ?Sarylach-Antimony? industrial plant is constructed for processing Au-Sb concentrates to receive antimony trioxide and gold from various antimony deposits of Sakha (Yakutia).

Jan 1, 2014

By P. Saha, D. M. Chakrabarti, National Metallurgical Laboratory, P. Bhattacharyya, B. R. Sarkhel

The estimated reserve of the phosphatic soils at the Sukulu hills region of Uganda upto a depth of 60 meters is of the order of 200 million tonnes and analyses 10-12% P2O5. A 5-tonne sample of the phosphatic soil was received at the National Metallurgical Laboratory (NML), India for beneficiation studies. The ore occurred as a naturally degraded soil deposit and the slime contained earthy lateritic minerals which made it extremely sticky. Microscopic examination revealed the presence of limonite, magnetite (martitised), hematite and goethite as major minerals along with apatite and quartz. Presence of clay was indicated by earthy smell on moistening the sample. It was observed that getting rid of the slime was as important for adequate beneficiation of the ore, as it was difficult. Earlier studies on samples of the same ore at the NML and abroad established that it was necessary to pass the ore through a series of three stages of desliming, each consisting of a step of rigorous attrition scrubbing followed by hydrocycloning, for effective elimination of the sticky slimy coating which stubbornly adhered to mineral grains. Studies were carried out at the NML in two phases to develop a flowsheet for beneficiation of the phosphatic soil. In the first phase, reproducibility of the results obtained by employing a flowsheet developed abroad was confirmed along with suggesting some modifications of the flowsheet. Then 200 kg. of concentrate was produced following the recommended flowsheet for evaluation of its suitability for production of fertilisers. To remove the limonitic slimy coating, which stubbornly adheres to the other mineral grains, it was necessary to subject the ROM ore, after screening out the +840 micron size fraction which contained only 1.75% P2O5 , to three stages of hydrocycloning each preceded by attrition scrubbing. Then only conventional beneficiation techniques could be effectively employed to upgrade the ore.

Jan 1, 2003

By J. D. Miller, C. L. Lin

In general, x-ray computed tomographic (CT) techniques are able to provide 3D images of the internal structure of opaque materials in a nondestructive manner. The unique cone beam geometry allows acquisition of all 2D projections with only one rotation of the sample thus providing for fast data acquisition and better x-ray utilization, as a complete 2-D detector array receives the cone-shaped flux of rays. Thus, an isotropic 3D volume can be reconstructed without the mechanical translation and the stacking of sequential slices as is the case for more conventional CT scanners. In this regard, a state-of-theart, custom designed x-ray microtomography facility to provide very detailed 3D spatial analysis of multiphase particles has been installed and is in operation at the University of Utah. The reconstructed 3D tomographic volume allows for an adjustable spatial resolution from 5 to 20 microns for sample dimensions from 10 to 40 mm in diameter, respectively. For example, a packed bed of coal particles is shown below in which different crystalline froms of pyrite are distinguished in 3D.

Jan 1, 2003

By W. Pawlos

"The paper will present the methods of visual observation and recording of movement paths of coal grains of different physical properties in the paramagnetic liquid. The paths were recorded with a video camera in the working chamber by means of a specially constructed device, acting as a periscope, which were then transformed into digital images.Experimental movement paths were confronted to the paths obtained in a theoretical way by means of solving differential equations of movement. The outlet level of a grain of the same physical properties from the separator is a random variable with normal distribution which modal value is equal to the outlet level of a spherical grain, calculated from the solution of grain movement equations. At these assumptions it is possible to calculate the height of the passage from the separator working chamber to separate a given product with a given separation accuracy, measured by a probable error and to determine separation conditions."

Jan 1, 2003

By Sashnee Raja, Mehdi Nemati, Ashley Sissing, Susan T. L. Harrison

"Extreme thermophiles, operating at 65 - 90°C, are finding increasing application in biohydrometallurgy. These micro-organisms have the advantage of exhibiting better oxidation kinetics in terms of reaction rate and extent of mineral solubilisation (Duarte et al., 1993; Norris and Barr, 1988; Konishi et al., 1995). These extreme thermophilic Archae, characterised by a different cell envelope structure (König and Stetter 1986, König 1988, Michel et al. 1980) perceived to provide reduced structural strength in comparison to bacterial envelopes, and customised metabolic pathwaysThe active tank bioleaching process, used for high rate leaching, is conducted in a slurry bioreactor. Here sufficient energy dissipation is required to ensure suspension of the mineral phase as well as to sustain high rates of gas liquid mass transfer. It is well known that subjection to hydrodynamic stress of sufficient magnitude may alter the physiological state of a range of micro-organisms through changed viability (ability of the microbes to grow), metabolic activity and integrity. While limited study on the influence of the solids phase on thermophilic leaching performance is reported, initial reports suggest that the thermophiles used for bio-oxidation appear to be sensitive to hydrodynamic conditions (Jordan et al 1993, Clark and Norris, 1996) and the presence of solids (Norris and Bar 1988, Le Roux and Wakerley, 1988, Escobar et al. 1993, Torres et al. 1995, Nemati and Harrison, 2000)."

Jan 1, 2003

By M. Brozek, W. Pawlos

"The separation of raw materials in the separator with ferromagnetic liquid occurs due to differences in magnetic and gravitational properties of respective components in relation to each other and to the liquid. In the separator with wedge-shaped pole shoes and the working space axis inclined at a certain angle to the horizontal direction, the paths of grain movement at fixed separation conditions depend on its physical properties. Due to this, the levels of grains outlet from the separator working space are differentiated according to differences in their physical properties. The distance between the levels of outlets from the separator working chamber depends on magnetization of the liquid which is proportional to the liquid density, on the magnetic field intensity and the inclination angle of the separator working passage to the horizontal axis. The separation accuracy is higher the larger is the distance between the outlet levels.The paper will present the methods of visual observation and recording of movement paths of coal grains of different physical properties in the paramagnetic liquid which was the water solution of manganese chloride. The paths were recorded with a video camera in the working chamber by means of a specially constructed device, acting as a periscope, which were then transformed into digital images. Experimental movement paths were confronted to the paths obtained in a theoretical way by means of solving differential equations of movement by a numerical method, achieving good compatibility of experimental and theoretical results. The equations of movement were solved with taking into consideration the drag force, expressed by formula for laminar and dynamic conditions of motion.The course of the path of grain movement depends on grain and liquid physical properties, magnetic field intensity and inclination angle of the working space to the horizontal direction. The two latter parameters can continuously control the process of separation."

Jan 1, 2003

By Fu Ping-Hao, Sergio Mauricio Vianna, Ewen Silvester, Emmy V. Manlapig

"Over the last 5 years, an ambitious project has been undertaken at the Julius Kruttschnitt Mineral Research Centre (JKMRC) aiming to isolate, study and, if possible, model the effect of particle size, liberation and collector adsorption density on the floatability of mineral particles. As part of this project, we have conducted highly controlled flotation test-work, combined with state-of-the-art solution and surface analytical techniques such as High Performance Liquid Chromatography (HPLC), Time of Flight Secondary Ion Mass Spectroscopy (TOF-SIMS) and detailed mineralogical analysis to fully characterize the flotation behavior of a natural ore.The flotation tests were undertaken using a high-grade lead-zinc ore from BHP-Billiton’s Cannington mine (Australia) in a specially designed continuously operated laboratory scale flotation rig. Solution and adsorbed collector concentrations were measured independently during the course of the flotation tests using HPLC based ex-situ techniques. Liberation studies were performed using the JKMRC Mineral Liberation Analyser (MLA) on selected size intervals of different streams to estimate the specific surface area of galena. These results were used to calculate the collector adsorption density (collector coverage) on galena particles, with the eventual aim of developing a mathematical model describing the relationship between pulp chemistry, feed mineralogy, and floatability of galena particles."

Jan 1, 2003

By K. W. Stöckelhuber, A. Wenger, H. J. Schulze

"An important elementary step of the flotation process is the forming, drainage and rupture of a thin intervening liquid film between bubble and mineral particle.After the encounter of the bubble with the solid surface a wetting film is formed. The initial thinning of this film is driven by the capillary pressure inside the bubble. When the film has reached a certain thickness rupture can take place.There are two possible mechanisms describing this process:-, Growing fluctuation waves (spinodal dewetting) on fluid interfaces under the influence of any kind of attractive forces (electrostatic, van der Waals). -, Nucleation inside the film.Metastable wetting films on negatively charged, hydrophobic glass surfaces (gaseous phase methylated), or on hydrophilic, positively charged glass surfaces (with Al3+ ions), have been analysed by means of the kinetics of film thinning according to the Reynolds law. These experiments demonstrate that both mechanisms can be responsible for the rupture of a thin wetting film. In the case of hydrophobic surfaces the nucleation mechanism is preferred; in the case of opposite charged silica surface the capillary waves mechanism due to an attractive electrostatic double layer force between silica and air bubble takes place.Hereby the existence of a long range hydrophobic force. on a hydrophobic surface can be excluded. The apparent interaction can be explained by the presence of gas nuclei formed on heterogeneous surface sites. The results provide deeper insight into the mechanisms of wetting film stability, adhesion process in flotation and droplet coalescence."

Jan 1, 2003

By E. Emelyanenko, P. Solozhenkin, J. Yagudina, O. Ibragimova

To recover tetrahedrite-tennantite series minerals from porphyry copper-pyrite ores by the froth flotation method, further research on thiol collectors is launched to promote the utilization efficiency of copper ores. In the present paper the adsorption mechanism of the collectors on tennantite surface has been investigated by computational modeling and FTIR-spectroscopic analysis, which have revealed that the decrease in prognosis of collector activity evaluation (PCAE) for tennantite is in the following order: BX (-0.34318), AEROPHINE 3418A (- 0.61756), AERO 5100 (-14.18857). The lower PCAE the stronger the ability of the collector to interact with the mineral surface of tennantite and form the stable complex. More kinetic reliable conditions to form suitable adsorption layer and rupture of the liquid interlayer with AERO 5100 have been observed by FTIR spectra due to decrease of the intensity and stretching and bending vibrations of water (less than 20 and 65%, respectively). In order to verify the feasibility of AERO 5100 as a collector the industrial flotation tests have been conducted. Flotation performance has improved significantly with the stadially grinding and preflotation of tennantite in intercycle copper flotation that allows to avoid desliming of the fragile mineral and minimize loss of Cu and As in tailings. The recovery of copper in copper concentrate increases by 3.9% with the grade maintained.

Jan 1, 2018

By M. Ghiani, R. Peretti, S. di Giovanni, G. Zonnedda, A. Serci

"An interesting occurrence of gold bearing ores of economic interest has recently been discovered in the Serrenti- Furtei district, central-southern Sardinia (Italy). The upper part of the orebodies are leaner and fairly porous, and are undergoing intense oxidation processes. In the lower parts sulphide ores predominate, chiefly enargite-luzonite and pyrite and these have a more compact structure. The passage from the oxidized to the sulphide zones, is rather irregular and difficult to delineate. The gold, generally occurring in its native form, is found in small grains. Mineral reserves in the area concerned were originally estimated to total 2.77 Mt: 0.63 Mt of oxide minerals with average gold content of 2.75 g/t and 2.14 Mt of sulphide ores with average gold grade of 3.18 g/t.Recovery of the valuable metals is a complex problem.The effectiveness of a variety of gold extraction techniques has been evaluated conducting tests on batches of ore representative of the different orebody depths obtained from core samples.The techniques investigated were: heap and vat leaching; flotation and flotation followed by leaching of the flotation tailings. The findings indicate that:• the gold contained in the ores in the upper oxidized zones of the deposit can be efficiently recovered by direct cyanidation via heap or vat leaching;• the sulphide ores in the deeper portions, that are not amenable to direct cyanidation but contain enargite concentrations of potential economic interest can be processed by means of flotation to produce a gold/copper bulk concentrate;• beneficiation of the difficult-to-treat minerals contained in the transition zone requires some knowledge of their intrinsic properties. A distinction should be made between the ores containing minor amounts of enargite which appear to be amenable to vat leaching and those with relatively higher enargite content which are processed using bulk flotation of the gold and copper minerals followed by vat leaching of the resultant tailings."

Jan 1, 2003

By P. Harris, D Bradshaw

"Comparison of the two most commonly used classes of depressant in the South African platinum industry is complicated by the fact that these polymers induce different effects on the surfaces onto which they adsorb. The use of carboxymethyl cellulose (CMC), which is ionically charged in solution, can lead to increased particle dispersion in addition to the effect of reduced surface hydrophobicity (depression). Guar is typically only slightly charged in solution. Comparison of these two depressants is complicated since it is uncertain whether differences in their action is a result of either depression of dispersion effects.This work investigates the role of dispersion independently to that of depression in the batch flotation of a platinum bearing ore. An inorganic dispersant, sodium hexametaphosphate (NaHMP) was added in parallel to the uncharged guar depressant to simulate the action of depressants with varying degrees of dispersion. By distinguishing between the material recovered by entrainment and the floatable gangue and by including the effects of froth stability it was possible to decouple the effects of dispersion and depression.The results show that both dispersion and depression led to increased grade of the sulphide minerals. Depression leads to a decreased recovery of floatable gangue minerals. Dispersion leads to an increased recovery rate of these minerals and an accompanying decrease in froth stability."

Jan 1, 2003