Search Documents

By l. Bokányi, T. Varga

"The recycling of waste car tyres is a very important environmental task. The waste tyres usually are re-used or recycled by thermal processes like pyrolysis, gasification or incineration. The main problem associated with these processes is the sulphur content of waste tyres originated from the vulcanisation process, which pollutes the environment and the valuable products (i.e. pyrolysis oil) as well. In our research the desulphurisation of waste, mechanically prepared tyre sample was systematically investigated by the biosolubilisation with Acidithiobacillus thiooxidans, strain Karitas. Parallel, the experiments with sterile 9K nutrient medium were also carried out. It was found that the vulcanisation sulphur can be solubilised due to both the bio- and the chemical leaching, although the bioleaching is more effective. The solubilised vulcanisation sulphur then forms precipitates. The precipitates are forming in the bulk solution, as well as on the surface of rubber particles. The origin of the precipitates was investigated using XRD and scanning microscopy with micro probe. The origin of the precipitates is different: while in the process of the vulcanisation sulphur solubilisation with 9K medium the jarosite (KFe3+3(SO4)2(OH)6) forms, the course of the biosolubilisation with Acidithiobacillus ferrooxidans Karitas is accompanied by the formation of the jarosite and the halotrichite (FeAl2(SO4)4 · 22H2O) as well. The formation of the latter is the biomineralisation. The mechanisms of the bio- and chemical solubilisations are rather different as it was found and experimentally proved by several tests, and depends on the retention time of the solubilisation. Special efforts were done to elaborate the proper separation of the precipitates from rubber particles. Combination of intense dynamic stirring and recycling flotation process to remove the precipitates was applied for this purpose. The surface properties of synthetic jarosite were revealed using zeta-potential measurements at different pH and in presence of collectors. The parameters of the flotation were chosen based on the revealed surface properties of the precipitates. Finally, the sulphur recovery of the recycled rubber was achieved as low as <0.5%, sulphur content of it 0.17%, 12-times lower than that of the waste tyre sample after mechanical preparation."

Jan 1, 2018

By Xiaoxu Sun, Jianchao Yao, Jiancheng He, Shijie Lu, Hongxi Zhou

"With the trend of increasingly more mineral resources turning low-grade and refractory, more and more new ore bodies being developed worldwide are more finely grained, which drives the rapidly development and application of techniques related to tower mills (vertical spiral stirred mills). However, the lacking in fundamentals of fine grinding, as well as standard procedures for equipment selection and scale up, seriously restraint high efficient application of tower mills. Taking grinding media motion characteristic and grinding intensity as a breakthrough point, this paper studies mechanisms behind how critical parameters affect grinding efficiency of tower mill, including ratio of screw pitch and diameter, agitator rotation speed, grinding media size. Several sets of orthogonal test are conducted on the quartz ore using the grinding system of KLM-3 tower mill. All the tests are under the same character of feeding mineral and undergo the consistent sampling for at least 60min grinding time. The input power is measured by a torque measurement system and the grinding products are analyzed by the laser particle size analyzer. The test results show the influence of parameters on grinding efficiency. Among the three important parameters, the effect of grinding media diameter is the biggest, followed by the agitator tip speed, and finally the ratio of screw pitch and diameter. For the different particle size of grinding products, the best combination of grinding parameters is different, with the mineral size becoming finer, the ratio of screw pitch and diameter become smaller, the diameter of grinding media become smaller, while the agitator tip speed does not change too much. The conclusions of the study help us to improve the grinding efficiency of the tower mill, to assist in the selection and optimization of working parameters, establish new scale up method on the basis of grinding model and eventually provide theoretical basis of rational selections of structural and media physical parameters within tower mill."

Jan 1, 2018

By Polezhaev S. Yu, I. V. Ukraintsev, Boduen A. Ya, Saburbayeva L. Yu

"Comparison studies of different technologies are performed when selecting optimum option for gold ore and concentrate processing. Methods of ultrafine grinding, oxidizing roasting, bacterial leaching and pressure oxidation are used to extract gold from refractory ores and concentrates. Refractory gold flotation concentrate produced from pyrite-arsenopyrite ores of Bestobe deposit is a case study in this paper. The results of the experimental tests of the direct leaching of flotation concentrate and pre-oxidation products using different methods (oxidizing roasting cinder, pressure oxidation and bacterial leaching cakes) are the following: - cyanidation of original flotation concentrate provides recovery of Au at 46.6 %; - oxidizing roasting increases gold recovery from 46.6 % to 85 %; - BIOX increases gold recovery up to 86 %; - preliminary pressure oxidation of flotation concentrate ensures steadily high Au extraction in the follow-up cyanidation at 94.9-96.5 %. Pressure oxidation and bio-oxidation has changed dramatically the strategy of refractory gold ore processing. These solutions provided for development of ore deposits that considered earlier non-commercial. However, refractory ore processing has a complex character in terms of developing process flowsheet and requires large amount of studies to be performed for each new project. Gold extraction is the basic but not the only criteria to technology selection for gold ore and concentrate processing. Opex and capex, ore reserves, regional geography, developed infrastructure and skill personnel should be considered. Process studies and feasibility study of the developed technology shall be provided for each specific gold ore deposit. INTRODUCTION Due to changes in available feedstock and depletion of easy-to-process ores, refractory ores containing finely disseminated gold and silver in sulphides (primarily, in pyrites and arsenopyrites) are more and more involved into processing. Experts say that such ores amount above 40 % of the world’s gold reserves. Conventional technologies of gold extraction from refractory ores include flotation, roasting and cinder cyanidation (Fraser etal., 1991). However, today’s best available practice for refractory gold ore processing are bacterial (BIOX) and pressure (POX) oxidation."

Jan 1, 2018

By E. V. Koporulina, E. L. Chanturiya, M. V. Ryazantseva, E. S. Zhuravleva

"The morphology of the surface of sphalerite, galena and chalcopyrite and the adsorption of butyl xanthate under conditions of preliminary treatment of minerals by the products of water electrolysis were studied using atomic force microscopy (AFM) and Diffuse Reflection Infrared Fourier Transform Infrared Spectroscopy (FTIR). It was determined that practically all types of treatment by electrochemically modified water (a product of non-diaphragmatic treatment, anolyte and catholyte) lead to an increase of surface roughness of the studied minerals due to formation of small rounded shape particles. In contrast to that, after treatment of chalcopyrite by anolyte, its surface becomes smoother. Various effects of treatment by the water electrolysis products on the adsorption of chemical and physical forms of butyl xanthate on the studied sulfides were established. As a result, the efficiency of the complex of AFM and FTIR methods, as one of the ex-situ approaches for monitoring the surface state of sulfide minerals and direct investigation of BKx adsorption products was demonstrated.INTRODUCTION In mineral processing, copper-zinc sulfide ores are one of the most complex products in view of their mineral composition, fine dissemination, complex inter-growth and the proximity of the technological characteristics of copper, zinc and iron sulfides. For the most complete disintegration, fine grinding of ores to a size of 0.074-0.044 mm is necessary. Consequently, the main method for processing of such ores is flotation, which bases on the difference in physical and chemical properties of the mineral surfaces, in particular, degree of wettability. The separation of copper and zinc minerals and their separation from ferrous and other sulfides, sulfosalts and rock mineral is a very difficult task (Chanturiya, 2000). For the successful separation of copper and zinc minerals in the appropriate selective concentrates, it is necessary to find conditions for the most complete liberation of ore and rock-forming minerals and for increase the contrast in physical and chemical properties of their surfaces. Despite significant progress in the processing of copper-zinc sulfide ores, the problem of the selectivity of the separation of the main ore minerals has not yet been fully solved and requires innovative approaches (Chanturiya, 2015). To date, various methods of preliminary energy processing of complex ores are used: magnetic pulse treatment, impact by high-voltage nanosecond pulses, electrochemical effects (including products of water electrolysis (Chanturiya et al., 2014; Bunin et al., 2015; Chanturiya et al., 2014a; Chanturiya et al., 2016), processing with flotation reagents, etc. Electrochemical treatment of water in various modes allows to obtain products of electrolysis with different oxidation-reduction properties: acid anolyte with a high oxidation potential and dissolved oxygen content, an alkaline catholyte with high reducing properties and a product of non-diaphragmatic treatment with enhanced reduction properties."

Jan 1, 2018

By C. Dorfling, C. A. Snyders

South Africa has extensive mineral processing and extractive metallurgy capacity and infrastructure for metal production from natural resources. Decreasing ore grades, increasing labor costs, and more stringent legislation have made economic metal production from primary resources challenging. Opportunities exist for metal production from secondary resources such as mining wastes and end-of-life consumer goods. The objectives of this study were to evaluate the current status of metal production from secondary resources in South Africa and to identify potential opportunities for further development. Two main classes of secondary resources, namely mining waste and electronic waste, were considered. Primary metal producers are dominating metal production from mining wastes; several of the gold, platinum and chrome producers operate low risk and low cost tailings retreatment facilities that contribute significantly to their overall production. Further opportunities exist in, for example, the treatment of more than 450 estimated gold tailings dumps in Gauteng, as well as metal recovery from slags and furnace dust. The majority of companies involved with electronic waste recycling in South Africa focus on collecting and disassembling; only a few perform preliminary physical processing, with the recovered fractions then being sent overseas for metal recovery. Projections are that the rate of waste generation will increase significantly and that treatment will become critical to comply with more stringent environmental legislation. Projects related to process development, techno-economic evaluations and environmental impact studies for metal recovery from batteries, printed circuit boards, and fluorescent lamps are underway. South Africa is ideally positioned to further explore opportunities for synergistic relations between metal recyclers and primary metal producers. Processing of electronic waste for production of technology metals, for which limited natural resources exist in South Africa, would be a key enabler for local manufacturing industries and expansion of the value chain.

Jan 1, 2018

By S. M. Bradshaw, V. Rocher, L Kabondo, B. Combrink, C. A. Snyders

Media losses are a significant contributor to the operational cost in a dense media separation (DMS) circuit. Of these losses, up to 80 wt% can occur on the drain and rinse vibrating screens. Although these screens are an integral part of any DMS circuit, surprisingly little work can be found in open literature regarding the effect of aperture configuration on the drain rates (draining water and medium). To establish the effect of slot aperture size, experiments were conducted on a 0.6 x 1.2 m vibrating screen with polyurethane (PU) panels at slurry densities between 1.6 – 2.8 kg/L, and volumetric flow rates of 19 – 25 m3/h for both ferrosilicon and magnetite. Results showed that an increase in the volumetric flow rate led to an increase in drainage rate, moisture content and medium carryover. Once an optimum volumetric flow rate was exceeded, a further increase in flow rate resulted in a decrease in drainage rate with a sharp increase in moisture and medium bypass to the oversize stream. An increase in ferrosilicon slurry density led to a decrease in drainage rate with an increase in moisture and medium bypass with each of these rates increasing as the slurry density increased. For magnetite, a gradual decrease in drainage rate was observed with increase in slurry density and volumetric flowrate beyond the screen optimum point. It was found that an increase in aperture size from 0.63 x 8.8 mm to 0.8 x 8.8 mm to 1.0 x 13 mm resulted in an increase in ferrosilicon drainage rate of between 1.3 - 1.8 m3/m2/h depending on the flow rate and slurry density with a reduction in moisture and medium carryover of between 1.0 – 1.2 % and 14.1 – 20.2 kg/t/m respectively. For magnetite, the drainage rate increased between 1.0 - 1.4 m3/m2/h as the slot width increased from 0.63 x 8.8 mm to 0.8 x 8.8 mm while an increase in slot length from 0.63 x 8.8 to 0.63 x 12 mm only resulted in an increase in drainage rate of 0.1 - 0.5 m3/m2/h.

Jan 1, 2018

By Xingshi Yang, Ghislain Bournival, Seher Ata

"Particle-laden interfaces are a fundamental research topic in froth flotation since the process involves particle-coated bubbles in both the pulp and the froth phase. In most experimental studies the characteristics of the particle layer in multi-bubble systems are poorly defined. An experimental setup has been developed based on a Langmuir-Blodgett (L-B) trough. The modified trough allowed introducing an air bubble beneath the particle monolayer formed at the air-water interface which made the study of the interaction between the bubble and the monolayer under various pH values possible. The monolayer characteristics of the particles were also studied and compared in terms of surface pressure (?-A) isotherms and packing factor. On compression, the particles formed branched structure at high pH whereas a uniform monolayer was formed at lower pH. Observations related to the behavior of particles during compression and expansion cycles, and the coalescence of a bare bubble with the flat particle laden interface were provided and the implication of the results for flotation process was discussed.INTRODUCTIONFroth flotation is known for its versatility and ability to concentrate low-grade, complex ores. It is considered a physico-chemical process in which particles attach to air bubbles, depending on their hydrophobicity as well as other factors, and are carried to the surface to form a froth layer. Reagents are used to stabilize bubbles and the froth layer (Pugh, 1996). However, particles, which are carried by the bubbles or entrained, significantly contribute to the stability of the froth phase (Ata et al., 2003; Zanin et al., 2009; Bournival et al., 2015a). Their relevance in mineral processing has led to a number of fundamental studies on the effect of particles and their properties on the process of froth flotation.Flotation systems are particularly difficult to characterize due to the broad range of properties of particles (e.g. size, liberation, hydrophobicity, etc.) and inconsistent operational conditions (e.g. changes in water quality, reagent addition, etc.). Several studies have made the use of well characterized particles in laboratory conditions. Such studies allowed the finding of an optimal contact angle for the stabilization of the froth phase (Johansson and Pugh, 1992; Ata et al., 2002). Froths have a large number of bubbles so that individual interactions are not observed. The study of two bubbles allows to determine the stability of the bubbles, with particles, and to some extend the stability of the bubble-particle aggregate (Gourram-Badri et al., 1997; Bournival et al., 2015b). The removing of particles between two bubbles may also be studied from a Scheludko cell (Johansson and Pugh, 1992) or by observing a bubble with a flat interface (Sethumadhavan et al., 2002). However, these systems provide limited information on the arrangement of the particles."

Jan 1, 2018

By A. Pirson, J. Souza, A. Araujo, M. Barbosa, F. Guimarães, J. Lima

"Although a large number of processes have been developed and applied to the separation of barite from other minerals, there is a lack of information in the literature about the separation of barite from iron ores. Nowadays, there are millions of tonnes of iron ore disposed as a waste or tailings given its high content of sulphur in the form of barite. In order to effectively separate barite from iron ore and ensure that mining business is truly creating economic and sustainable values, this paper provides a greater understanding of barite properties, the origin and occurrence of this barium-bearing mineral, and the employed beneficiation processes. A test work is conducted in a barite bearing iron ore from a deposit located in the Republika Srpska (Bosnia and Herzegovina) in order to separate the barite and check if a marketable by-product can be produced by drawing upon rich barite tailings. INTRODUCTION The exploration of iron ore containing barite results in a large amount of unrecovered material. The main difficulty in processing and using barite bearing iron ores is given by their high content of sulphur, silica and barium, which are unwanted chemical compounds in the subsequent processes in iron industry. As a result, millions of tonnes of iron ore are discarded every year into tailings or as a waste, which results in production losses, higher operation costs and environmental impacts (Praes et al. 2013). Therefore, the separation of barite from iron ores not only means reducing the environmental impact, but also an opportunity to generate income and beneficiate society. The beneficiation of barite bearing iron ores is a subject which requires a deeper investigation to solve the challenges faced by the iron industry. There are only a few studies that describe flowsheets proposed for the production of barite concentrate of iron ores. The most likely reason for this gap is that barite is frequently exploited commercially as a primary product rather than a by-product. In order to effectively separate barite from iron ore and ensure that mining business is truly creating economic and sustainable values, this paper provides a greater understanding of barite properties, the origin and occurrence of this barium-bearing mineral, and the employed beneficiation processes. A test work is conducted in a barite bearing iron ore from a deposit located in the Republika Srpska (Bosnia and Herzegovina) in order to separate the barite and verify if a marketable by-product can be produced by drawing upon rich barite tailings."

Jan 1, 2018

By S. L. Gubin, T. V. Ignatova, A. V. Levshin, D. O. Sharkovsky

"Flotation process applied for concentration of unoxidized ferruginous quartzites by PJSC Mikhailovsky GOK (MGOK) is based on wet magnetic separation of strong magnetic minerals. However quality of the resulting concentrate (Fe65-66%) is insufficient for production of metallics. Quality upgrade of magnetite concentrate via flotation has been implemented by MGOK to produce premium quality magnetite concentrate.Flotation is a challenging process due to sensitivity to varied amounts of reagents, fine and coarse mineral ratio, particle contact (retention) time and temperature of feed. Tomah’s PA-14 reagent (USA) has proven efficient for application in flotation of MGOK’s magnetite concentrate.Objective of this work is to select and prove applicability of selective agents for flotation upgrade of magnetite iron ore concentrate.Series of flotation tests has been carried out with application of new highly selective collecting agents produced by Akzo Nobel (Sweden), Clariant (Germany) as well as Akzo Nobel’s and Tomah’s cationic collector mix to improve performance efficiency of flotation process. Tomah’s flotation agents and Akzo Nobel’s Lilaflotproved to be the most effective for purposes of concentrate quality upgrade to Fe69.0% via flotation.Testing Method: Following scientific research methods were applied for testwork: system analysis, mathematical statistics, observation, comparison, trial (experiment).To determine key process factors a series of pilot tests was carried out. Most of the testwork was performed by PJSC Mikhailovsky GOK’s Central Process Laboratory.Work Results:-optimized flotation performance modes were defined to ensure production of three types of low-silica concentrate, i.e. containing SiO25%, SiO24% and below SiO23% by weight. Most efficient selective agents applicable for flotation have been defined. Mixture of higher aliphatic amines has proven to intensify selective flotation of quartz. It enables higher yield of chamber product maintaining desired quality of concentrate.Achieved process operation and performance factors have been revaluated.Value for Advancement and Expansion of Mineral Processing:Flotation of concentrate has enabled expansion of PJSC Mikhailovsky GOK’s production capacity, improved production quality, helped to maintain sustainability and competitive advantage of the company."

Jan 1, 2018

By S. Mitra1

"This study aims to investigate coarse particle detachment mechanisms (particle diameter > 150 ?m) utilising both experimental and numerical technique. Two mechanisms were studied – (i) interactions of bubbleparticle (BP) aggregate with vortices and (ii) coalescence of bubble-particle aggregates. On the first mechanism, interaction behaviour of coherent vortex structures with a BP aggregate (bubble diameter db = 3 mm, particle diameter dp = 0.3 mm) was studied using a CFD model in the Reynolds number range of 100 to 1000. Effect of surface hydrophobicity on the BP stability was examined using a range of contact angle boundary conditions. To address the second mechanism, interactions of bubble-particle aggregate (db ~ 4 mm, dp ~ 0.4 mm) with both free gas-liquid interface and individual bubbles were investigated using high speed imaging. Both rebound and coalescence outcomes were observed to be responsible for BP instability leading to particle detachment.INTRODUCTIONIt is widely known that flotation process performs excellent mineral recovery for base metal ore particles that are typically in the range of ~ 20 to 150 µm in diameter (Jameson, 2010). More specifically, higher recoveries are usually reported for particles in the size range of ~20 to 70 µm while outside this spectrum, generally the recovery diminishes significantly. It would be highly desirable to improve the recovery of particles at the coarse end of the flotation size range spectrum which has significant economic benefit (Jameson, 2010). However, it is essential that insights to particle detachment phenomenon, the primary impediment in coarse particle flotation caused by the underlying hydrodynamic factors are first obtained at a greater depth.In an ideal quiescent liquid medium, due to inertia, coarse particles deviate substantially from the fluid streamlines and collision efficiency with bubbles decreases which can only be augmented by increasing turbulence level in the medium sufficiently to make random physical contacts with bubbles. Nonetheless, even if successful contacts are made, it is difficult for these large particles to remain attached to bubbles in a turbulent shear flow environment. There are two major mechanisms postulated for particle detachment – interaction of turbulent flow structures (eddies) with BP aggregate and coalescence among surrounding aggregates. Earlier work of Schulze (1982) theorised a vortex acceleration component to characterise turbulence effect on BP aggregate instability in flotation machines. Wang et al. (2015) investigated bubble detachment behaviour from a stationary particle in a nearly homogeneous and isotropic flow field. Using PIV (particle image velocimetry), it was shown that the local maximum energy dissipation rate for the case of bubble detachment was significantly higher than the no detachment case, and was also higher than the critical value for bubble detachment calculated using Schulze’ theory (Schulze, 1982). Later, Wang et al. (2017) also visualised the BP aggregate instability in a cavity flow leading to particle detachment which was attributed to bubble coalescence, bubble surface oscillation and particle deceleration phenomena."

Jan 1, 2018

By M. Surracco, M. C. Tilocca

"Mineral comminution is often a costly process which also requires high level of energy. In the course of the studies carried out by the researchers of the Department of Civil-Environmental Engineering and Architecture at the University of Cagliari, aiming at the optimization of the reduction processes, it has been experimented, among of others, the effects of high-speed water jets on minerals grinding. As far as coal is concerned, some of the solutions initially adopted are presented in this paper, which essentially relied on the water jet power only, with secondary use of mechanical actions, to reach the most modern solutions that envisage the use of mechanical energy, normally used in traditional grinding machines, in synergy with hydraulic energy transferred by water jet.INTRODUCTION Mineral comminution can be rather expensive and demand a high-energy consumption, especially for fine sizes (Austin, 1979). Further interesting perspectives in this area may be offered by comminution means aided by high pressure water jets (Ciccu 2007), whose crushing potential is currently used for several operations such as cutting different materials, rock digging and industrial cleaning. The crushing action of water jets may induce a traction stress in materials where substances of a mineral nature, especially if characterised by permeable porosity, oppose a minor resistance (Griffith, 1920). The first solutions to this purpose essentially relied on the sole energy of water jets, with a secondary use of mechanical actions (Ciccu, 1993). Results were encouraging, despite the high values of specific energy for the low capacity of treatment. However, due to the difficulty in making the techniques mainly based on hydraulic energy practically applicable to solids comminution a solution was experimented, with some interesting results, consisting in the combination of mechanical energy, normally used in traditional grinding devices, with hydraulic energy transferred through water jets, in a synergic relationship (Ciccu, 1998; Tilocca, 2016)."

Jan 1, 2018

By Kym Runge, Wei Huang, Fengnian Shi, Christian Antonio

"This paper presents an emerging High Voltage Pulse (HVP) technology for ore pre-treatment. Unlike previous studies where HVP was utilized as a crusher to pulverize ore particles to micron size ranges for downstream processing, the researchers at the Julius Kruttschnitt Mineral Research Centre (JKMRC) use HVP to enhance ore processability. Application of relatively low levels of HVP energy to selectively break mineralized particles from barren rocks, followed by size-based screening separation enables the feed ore to be split into high grade and low grade products. During HVP treatment, cracks/micro-cracks are generated which results in pre-weakening of the treated ore particles, which ultimately results in energy savings in the downstream comminution processes. HVP treatment followed by conventional grinding also results in improved liberation of the valuable minerals in comparison to that achieved with traditional conventional comminution, subsequently improving downstream separation efficiencies. The three major improvements in ore processability through HVP pre-treatment have the potential to facilitate rejection of low grade ore prior to processing, increase production rates, reduce the energy required for comminution and improve flotation separation recoveries. This paper summarizes the major research outcomes of HVP pre-treatment demonstrated using ores from various mining operations conducted by the JKMRC. It also discusses the barriers that must be overcome before it can be adopted by industry with confidence in a continuous high tonnage rate application.INTRODUCTIONThe challenges of declining ore grades and increased plant throughput rates, resulting in higher energy consumption and operational costs, require the mining industry to adopt new technologies to make future ore treatment economically viable. Over the past 50 years, many researchers have engaged in investigating novel comminution techniques. Since Yutkin (1955) first demonstrated the potential to generate shock waves with pressures exceeding 103 MPa via electrical breakdown of water, several applications of electrohydraulic crushing by shock waves have been reported (Curley-Macauly, 1968). Interest in this technique was bolstered when Andres (1977) demonstrated that electrodynamic fragmentation results in superior liberation of mineral grains as compared with conventional grinding techniques. Despite mounting laboratory-scale evidence of the efficacy of electrodynamic fragmentation for mineral liberation, development of the technology for full-scale operation has stalled, primarily because the energy required to achieve desirable mineral liberation is approximately two to three times that of mechanical comminution, amounting to approximately 100 kWh/t for typical mineral ores (Andres et al., 2002)."

Jan 1, 2018

By U. A. Peuker

"Steam Pressure Filtration (SPF) is a modified cake filtration process and is characterized by both washing and excellent de-watering of the filter cake. Compared to conventional gas differential pressure filtration, the filter cake is treated with saturated or superheated steam replacing pressurized air. Invented in the early last century, Steam Pressure Filtration has reached technical maturity in the 1990ies for inorganic particle systems, fine chemicals and coal. Especially the de-watering performance for fine particles systems below 50 µm make Steam Pressure Filtration an excellent option for the processing of fine tailings streams, to produce a stable material, which can be described by the methods of solids mechanics instead of paste rheology. The washing, which is due to the condensing steam, is able to reduce the ion load of the solid. This additional effect is able to generate a dry tailings material, which shows a reduced leaching potential of mobile ions, which originally derive from the process water. INTRODUCTION Steam Pressure Filtration is a process concept especially of hyperbaric filtration, which started its market entry in the 1990ies (Bott 1996, Bott 2002). Even though there have been many attempts to apply steam on filters before, the success story began with the combination of hyperbaric filtration and steam application and the technical solution to limit the steam treatment to a defined zone on the filter. This resulted from the scientific findings that steam mainly enhances the de-watering during the mechanical filtration (Gerl 1999). There are no or minor positive effects of steam application to a filtration process during cake filtration and after the steam breakthrough has occurred. Furthermore that time a sufficient control technology to regulate the steam consumption as well as suitable filter cloths became available. There is a growing need for de-watering technology in the mining industry, not only for the concentrate but also for the tailings streams. Several reasons argue against the established solution of damping the tails as suspension or paste into tailings ponds. There are ecological, political, societal and economic reasons, which question the tailings ponds more and more. Due to the increasing costs in the building and monitoring of tailings dams, which contain the tailing ponds, the concept of dry stocking using filtration technology comes into the game (Jansson 2016). Dry stocking converts the tailings stream form the suspension or paste state, into a material, which can be stockpiled. The latter typically is a moist flowable disperse particle system. The conversion involves a de-watering step, in which different types of filter equipment can be used, e.g. filter presses, membrane filter presses, automatic press filters or hyperbaric filters. For coarse products also vacuum filter can be applied. Due to its excellent de-watering performance and the easy scale-up properties Steam Pressure Filtration is further option for dry tailings stacking."

Jan 1, 2018

By P. K. Fedotov

Annually at least 5% percent of world power consumption is involved in the process of ore dressing while ore processing technology. Such rate of energy consumption demonstrates the importance of a given process study in the human life-sustaining activity. Examining of interparticle destruction being under external stress pressure in ore responses this problem solution at the greatest degree. The technology of destruction in the roll press is of great interest. The use of the given equipment allows to save a significant amount of energy by means of the built-in ore destruction mechanism. Examination of stress-strain fields which determine the level of interparticle destruction between the rolls in the ore layer enables to specify both level of ore destruction and power consumption. The mathematical computer modeling for the deformable environment use based on the finite-element method (FEM) allows to carry out the given research. We use FEM solution for elastic contact problem for the most complete study of power consumption employed in ore and interparticle destruction. This problem solution allows also to examine energy consumption expenses spent for ore crushing in the roll press. Also we have identified the mechanism of ore in a layer of the particles under pressure roller press. It is established that high level of performance and reduction of energy consumption in interparticle destruction of ore in the layer due to the appearance of the gradient of normal stresses in contact of particles of mineral raw materials. The algorithm has been developed determining crushing product particle size distribution of fractured particles in the layer, using the Bond’s theory of crushing. The use of our FEM model reduces the time of equipment selection for new plant and at the design stage to reduce the risks of errors in the choice of roller presses.

Jan 1, 2018

By H. Matsuoka, M. Kawata, K. Haga, K. Mitsuhashi, C. Tokoro, A. Shibayama, R. Kawarabuki

"The mineral surface characteristic is important for the flotation because it affects the flotation behavior of the mineral. Conventionally, in the flotation process for Cu sulphide ores, the degree of ore floatabilities varies depending on the mineral phase such as chalcopyrite, bornite, or chalcocite. Therefore, mineral surfaces are treated with activators and depressants to control the floatability of target minerals and obtain high recovery performance. There are lots of flotation reagents which have many effects on ores depending on ore characteristics and conditioning methods. For example, sodium hydrosulphide (NaHS) as activator is known to have the effect of resulfurizing and activating oxidized surface of chalcocite and bornite. On the other hand, NaHS is reported to depress chalcopyrite floatability. In this study, the evaluation of mineral surfaces was conducted to predict flotation behavior. Activation of Cu minerals (chalcocite, bornite, and chalcopyrite) by NaHS was experimented. The three Cu minerals were treated in two steps. Firstly, they were oxidized in the drying oven. Secondly, they were treated with NaHS solution. After each treatment step, each mineral was measured by contact angle apparatus then analyzed by X-ray photoelectron spectroscopy (XPS). The results of surface characteristics after oxidation and NaHS treatment were utilized to accomplish the study’s objective. INTRODUCTIONCopper sulfide minerals such as chalcocite (Cu2S), bornite (Cu5FeS4), chalcopyrite (CuFeS2) are well-known abundant copper-containing minerals. Generally, these minerals are recovered and concentrated via collector flotation. In flotation, the wettability of the mineral surface is an important factor in its recovery. When the surface is hydrophobic, the mineral has high floatability and when the surface is hydrophilic, it has low floatability. Usually, Cu sulfide minerals have high floatability. However when their surfaces are oxidized, their floatability becomes lower in flotation. In this case of surface oxidation occurrence, activators are added before flotation to modify the surface property of the Cu sulfide minerals so that they can be floated at a certain flotation condition. Sodium hydrosulfide, NaHS, is known as one of the activators. Zhao et al. (2018) reported that NaHS is often used as sulfurizer for oxidized sulfide minerals (Becker et al., 2014, Clark et al., 2000, Newell et al., 2006, 2007, Newell and Bradshaw, 2007). Although the floatability of Cu sulfide minerals was raised by adding NaHS generally, the results of this flotation study showed that the flotation behaviors of mixed chalcocite, bornite, and chalcopyrite were different. Therefore, it was considered that NaHS works differently for each mineral."

Jan 1, 2018

By L. Filippov

"Nickel is an important metal with the total global consumption of about 2 million tons per year. It is sourced from both sulfide and laterite ore, but currently laterites are becoming more attractive for nickel production due to the depletion of high grade nickel sulfide ores. Laterites are generally processed by hydro or pyro-metallurgy and therefore, pre-concentration of nickel before such processes is very important. In this paper the effect different physical methods (including flotation) on the pre-concentration of nickel in laterite ores will be discussed. The ore used in this study was a laterite from South East Asia. Nickel was upgraded using different methods such as magnetic separation, flotation and sizing. The effect of ore mineralogy on choosing the best strategy to upgrade nickel will be discussed. The findings of this project will help to unlock a substantial volume of nickel with significant value from laterite ores.INTRODUCTION Nickel is an important metal with the total global consumption of about million tons per year which has grown rapidly during last decades (Mackey, 2011). Nickel is sourced from two different types of ores, sulfide and laterite. The majority (about 70%) of the world’s nickel resources occur as laterite ores which are often complex, and low grade, and therefore expensive to treat using conventional methods (Xu et al., 2013). Today, nickel laterites are more attractive for production of nickel as the amount of high grade nickel sulfide ores has diminished (Janwong, 2012). Therefore more economic processes to recover nickel from these resources should be developed.It should be noted that nickel laterite mineralogy is complex, and nickel often presents as ultrafine inclusions in a number of mineral phases. Because of the low nickel concentration and variable distribution in these phases, effective upgrading by physical separation processes would be challenging. Researchers have tried to improve nickel laterite flotation recovery by using a number of feed preparation techniques. A summary of the nickel grades obtained using flotation and magnetic separation as reported in the literature is presented in Table 1. It can be seen that only minor nickel upgrades have been reported. Quast et al. (2015) have concluded that the complex mineralogy of nickel laterite ores makes it difficult to achieve any significant nickel upgrading by physical techniques, including flotation. They achieved 40% increase in the nickel content (from 1.0% to 1.4%) at a nickel recovery of 43% (Quast et al., 2015). Various attempts in USA, New Caledonia, India and Australia, to upgrade nickel in laterite using magnetic separation have not been successful (Quast et al., 2015). A recent comprehensive review on topics influencing nickel laterite flotation has shown that further investigations in the flotation of laterite ores are undoubtedly warranted (Farrokhpay & Filippov, 2016)."

Jan 1, 2018

By A. A. Novoselov, U. Kelm

"Large volumes of mine tailings accumulated in surroundings of porphyry copper deposits represent a growing threat to environment. They contain significant concentrations of toxic metal and metalloids which can contaminate river runoff, ground waters or can be transported by wind. Both extreme pH of fluids in tailings impoundments and high surface areas of processed mineral grains provide their increased reactivity. As a result, during only a few decades, As, Cu, and Mo can be mobilized, redistributed through the tailing column and accumulated through post-deposition leaching, evaporation and contamination with natural fluids. Those processes are reflected in the forming of secondary minerals. Gypsum, Fe oxides/hydroxides, efflorescent salts and clay minerals are typical alteration products in tailings. Here we present the results of reactive transport simulations implemented on the base of PHREEQC and SUTRA codes. The one-dimension model emulates the mass balance between rainfall, evaporation and subsurface runoff, the kinetically- and thermodynamically-driven dissolution of tailing minerals, advective and diffusive transport of tailing fluids, and precipitation of secondary phases. A typical tailing column is composed of four unequal layers with predominance of (i) evaporation, (ii) secondary mineralization above, (iii) below water table, and (iv) near the bottom of dump. Those horizons are characterized by contrasting pH, chemical composition and bulk mineralization of pore fluids, distinct accessibility of atmospheric oxygen and, as a consequence, distinct intensity of sulfide oxidation. The modeling and its verification on Chilean tailings impoundments reveal the complexity and high rates of secondary mineralization. The accumulation of toxic alteration products is controlled by fluid transport through the tailing column induced by both rainfall/evaporation and exchange with subsurface runoff. The geochemical modeling is a powerful approach which allows comparing the processes in tailing deposits produced by distinct flotation regimes and providing the long-term predictions of their environmental impact as well as identifying sectors of tailings for possible re-processing."

Jan 1, 2018

By D. Steele, B. Ndlovu

"Adequate characterisation of clays is becoming increasingly important as operating mines move into areas of more complex ores. The processing therefore needs better mineralogical characterisation to identify problematic ores for better planning before issues arise. While a number of instrumental mineral characterisation methods are available, X-ray Diffraction (XRD) is widely recognised as perhaps the best technique for the identification and quantification of minerals, particularly clays. When an appropriate sequential and systematic sample preparation and treatment protocol is employed with instrumental XRD analysis individual clays can be uniquely identified, and the proportions of interstratified clays can also be quantified. The effect of sample preparation on the XRD analysis and identification of clays was investigated in this study. The results showed that sample preparation protocol is indeed critical to accurately analysis and characterisation of clays. For example, both dry grinding and micronizing affected the degree of crystallinity of kaolinite leading to the formation of reactive surfaces or changes in the physicochemical behavior. It was also found that the apparent degree of preferred orientation in platy minerals correlates directly with the amount of force/pressure applied during the preparation of backfilled powder samples. This work showed that manual preparation can produce highly variable peak intensities especially with minerals that show any preferred orientation. KEYWORDS Clay; XRD; kaolinite INTRODUCTION Clays are important in our life and they have numerous applications in modern world from cosmetics to environmental remediation. Therefore, clays have been extensively investigated for many years. Adequate characterisation of clays is becoming increasingly important as the mineral processing industry faces more complex mineralogy with the need for better mineralogical characterisation to identify problematic ores and plan accordingly. In most studies, X-ray diffraction (XRD) method has shown the unique capability to characterise mineralogy, especially for the fine grained size materials. The XRD technique is particularly diagnostic for clays. It is known that under ideal conditions, the peak intensities of an XRD diffractogram are proportional to the concentrations of individual minerals present in the sample. Hence, the qualitative mineralogical data obtained from XRD can be quantified, using either the internal or external standard methods. However, it is also known that clays are particularly sensitive to the influences of sample preparation method due to their physical characteristics (e.g. fine grain size, morphology, relative physical softness, crystallinity, thermal sensitivity) that could be destroyed by inappropriate preparation prior to the analysis. Thermal and mechanical treatment and grinding of clays can change their crystalline structure, and consequently, their characterisation results by XRD analysis. The behaviour of clays in grinding has been widely studied, especially for kaolinite (Miller and Oulton, 1970, Milocevic et al., 1992, Tomasevic-Canovic et al., 1992). With prolonged grinding time, the crystallinity of the clays can decrease (Filipovic-Petrovic et al., 2002). It has been shown that grinding may gradually cause the loss of hydroxyl ions of kaolinite (Gonzalez Garcia et al., 1991)."

Jan 1, 2018

By B. McFadzean, J. Taguta

The enthalpy of immersion is the heat change arising from the replacement of the solid-gas interface with the solid-liquid interface when a solid surface is immersed in a liquid. Although immersion calorimetry has been established as a valuable and reliable means of determining solid surface properties such as wettability, it has seldom been applied in mineral processing research. In this study, precision solution calorimetry was employed to measure the enthalpies of immersion of different minerals in water. The enthalpies of immersion were then related to the first-order flotation rate constant as determined by the microflotation technique. The same measurements were also made on sulphide minerals whose surfaces were modified to different degrees of hydrophobicity using different percentage coverages of amyl xanthate collector. The enthalpy of immersion technique was capable of distinguishing and ranking minerals according to their wettability. All mineral types and collector-treated minerals conformed to the same relationship that was found between the enthalpy of immersion and the flotation rate constant. This conformed, empirically, to a power law equation. As the enthalpy of immersion decreased, there were large increases in flotation response for very small changes in hydrophobicity. In addition, a critical enthalpy of immersion (CEI) was found, above which no flotation could occur. The scatter in the data points could be corrected for by adjusting the rate constant using the density of the minerals to produce a robust relationship between the rate constant and enthalpy of immersion. These results have shown that the enthalpy of immersion is able to indicate both the natural mineral hydrophobicity and the extent to which collectors can render a mineral hydrophobic. This technique has considerable potential to be used as a sensitive and accurate measure of mineral surface wettability in order to predict flotation performance.

Jan 1, 2018

By E. Ashirbaeva

"Ores of ferrous metals traditionally make up the bulk of recoverable reserves of solid minerals, and iron ore concentrates - in the processing and consumption. To obtain concentrates, three main methods are used: dry and wet magnetic separation, gravity and flotation. But even their integration into complex developed schemes with finishing operations often do not solve the problem of obtaining high-quality concentrates, which are necessary for powder metallurgy and electric steelmaking. Increasing the iron content in the concentrate by removing harmful impurities is the goal of this work. The possibility of reducing the operations of wet magnetic separation twice and completely eliminating concentrating operations in ball mills from the scheme of operations has been established. Selective leaching agents for each type of iron ores have been created, allowing to obtain concentrates with an iron content of not less than 68-69% and negligible concentrations of harmful impurities. Methodical recommendations for long-term storage of bioreagents in the active state, their immobilization and preparation in industrial conditions at the enterprise Nedropolzovatelja are developed. The proposed biotechnology, which allows to obtain high quality iron and conditional concentrates for harmful impurities, is protected by patents (RU 2537684 ""Method for fine-tuning of high-sulfur magnetite concentrate"" for magnetite ores and Pat. RU 2599068. For the industrial implementation of the new technology, organizational and technological measures have been developed in the system with Road maps for types of ores. The developed technology makes it possible to condition noble metal, tin, tungsten, nickel and other concentrates in harmful impurities such as arsenic, antimony, mercury, sulfur, copper, zinc, iron, phosphorus, manganese, in total 30 components that pass into solution under the influence of bioreagents.INTRODUCTION Consumption of various metals is steadily increasing every year, the volume of mining is constantly increasing. Ores of ferrous metals traditionally make up the bulk of the recoverable reserves of solid minerals. Enrichment technologies for iron-containing ores are reduced to the combination of three main methods: wet and dry magnetic separation, gravity and flotation. But even the use of complex advanced technological schemes often does not lead to the production of high-quality concentrates suitable for metallurgical processing. In this case, either lapping operations or effective technical and technological solutions are used in the main enrichment cycle. Widely used in practice methods for improving the quality of iron ore concentrates include the use of finishing operations (fine screening, reverse cation flotation), staging of concentrates, the use of more sophisticated equipment (separators with running magnetic field, magnetic gravity classifiers, column flotation machines)."

Jan 1, 2018