Search Documents

By C. O. Riggs

Geotechnical exploration in North America, in particular, exploration for deep foundations analyses, is currently and generally performed following the most basic sampling and insitu testing methods and techniques. Some would surely say that the state-of-practice severely lags the state-of-the-art. Probably more than 90% of all deep foundations, both driven piles and drilled piers, installed in North America are initially analyzed and designed, i. e. geotechnically, on the basis of either the soil penetration resistance obtained by performing the "Standard Penetration Test" (SPT), or from laboratory shear tests performed on samples obtained using 76-mm (3-in.) nominal diameter, thin wall, "Shelby tube" samplers. The use of design data obtained with other exploration methods and devices, such as bore hole pressure meters, flat plate dilatometers, even cone penetrometers, occur on the fringes of practice and often in conjunction with the use of the two simpler methods of analysis. This basic approach probably represents an attempt of the profession to use, as much as possible, common, easily understood and easily communicated procedures in all geologic environments. The characteristics of drill rigs with the required drilling and samplng tools vary somewhat from region to region in North America according to the physiography of the area of use, the types of exploration data required on a day-to-day basis, the philosophy of the engineers and geologists that use the exploration data and the financial resources of the drill rig owner. The physical capability of the exploration drill rig used on a project can have a significant effect on the quality of samples or insitu tests. The physical configuration and the quality of the drill and the drilling, sampling and testing tools not only provide the mechanical capability to obtain data but affect the attitude of the field exploration crew and the quality of work. This complete presentation is taken, for the most part, from a book in preparation for publication: "Geotechnical Exploration and Site Characterization" by C. Riggs, A. Hatheway and N. Schmidt. The book is scheduled for completion during 1987.

Jan 1, 2010

By Timothy C. Siegel, Paul J. Axtell

The Missouri Department of Transportation (MoDOT) recently replaced the Hurricane Deck Bridge that carries Highway 5 traffic across the Osage Arm of the Lake of the Ozarks in Camden County, Missouri. The former bridge was constructed in the 1920's and was supported on pneumatic caissons bearing on dolostone bedrock. The replacement structure is founded on drilled shafts socketed into the bedrock. During the design phase of this bid-build project, a baseline design was developed and Alternative Technical Concepts (ATC's) were allowed from approved contractors. Those ATC's were confidential and not shared between teams. Either the baseline design or the approved ATC design could be bid by the respective contractors. The baseline design included re-use of the 90-year old caisson foundations. Accordingly, an extensive evaluation of the caissons and underlying bedrock were conducted by coring, laboratory testing, acoustic tele-viewer (ATV), and cross-hole sonic logging (CSL) methods. The results of the investigation indicated the caissons were in excellent condition and suitable for re-use. However, a more cost-effective ATC was submitted, awarded, and constructed that did not re-use the existing caisson foundations but rather reduced the span lengths, increased the number of piers in the water, and supported those piers on drilled shafts. Interestingly, the difference in low bid price between the awarded ATC and the baseline design was less than one percent of the construction cost. This paper describes the multiple foundation designs that were necessary for this interesting project. The various foundation evaluations include the existing pneumatic caissons, large-diameter open-ended pipe piles to support the baseline design, and the design of rock-socketed drilled shafts that were successfully constructed in 2012.

Jan 1, 2017

By Randy R. Huberty

Although originally designed with deep foundations consisting of all driven steel H piles and drilled caissons, a unique application of Augered Cast-in-Place (ACIP) piles as an alternate design resulted in a significant cost savings for the Midfield Terminal Project at the Pittsburgh International Airport. The project was enormous in scope covering an area two miles long by one mile wide, with changes in elevation of over 200 ft. The varying geology combined with the large amounts of fill required resulted in a complex set of geotechnical design parameters that had to be evaluated through both load testing and analyses. A total of almost 400,000 lineal feet of ACIP piles were installed for this project.

Jan 1, 2001

By António A. Henriques, António Gomes Correia, Ana Teixeira

"Abstract Pile foundations are often used for important structures, and thus, reliability evaluation is an important aspect of the design. Reliability methods have become increasingly important as decision support tools in different areas. The main benefit of reliability analysis is that it provides quantitative information about the parameters (uncertainties) that most significantly influence the behaviour under study. In particular, the design of pile foundations still involves many limitations and uncertainties, particularly when there is not enough investment in soil characterisation and/or pile load tests. In addition to the uncertainties associated with soil characterisation, physical, statistical, spatial and human uncertainties exist. In this subject, the primary purpose of this paper is to demonstrate the application of reliability methods to geotechnical pile design (axial load). It also presents a simple and practical approach to performing it using Monte Carlo Simulations, intending to provide knowledge for code harmonisation and encouraging the development of such methodologies in geotechnical practice. Sensitivity analyses are shown to understand the influence of each uncertainty type coming from different sources. An application example indicates, corroborating other studies, that the model error is the most influent uncertainty. As such, when using the different models (SPT-, CPT- and PMT-based) for bearing capacity, the results emphasise the need for a well-defined and wellcharacterised resistance model, also these results allow the engineer to understand how important the load tests can be to achieve reliable results and economic designs.1 IntroductionUnlike the approach to reliability evaluation used in structural engineering, the traditional procedure used in geotechnical designs addresses uncertainties through high global or partial safety factors (SF), mostly based on past experience. However, this approach to addressing uncertainties does not provide a rational basis for understanding their influence on design.Furthermore, the new regulation codes and social concerns, such as the sustainability or the economy, are imposing geotechnical engineers to increase their ability to deal with uncertainty in a direct and more rational way. Designs should be economic, sustainable and reliable at the same time. Concerning the reliability part of design, different approaches can be done, but the most important thing to keep in mind is the simplicity and efficiency of the tools and applied methods."

Jan 1, 2014

By Jeffrey R. Hill

This paper discusses the use of micropiles for the rehabilitation of the following two structures: the Milwaukee Auditorium Theatre, in Milwaukee, Wisconsin, and the Cupples Ballpark Lofts, in St. Louis, Missouri. The paper focuses on the similarities and differences of the remediation techniques used for each structure. The discussion highlights the method of attaching the micropiles to each respective structure. Generally the paper discusses the micropile installation at each project with supporting photos, figures and data. Load testing at each project is also discussed, including the comparison of load test results for each project. The paper will focus on the load testing program at the Milwaukee Auditorium Theatre where high capacity micropiles were designed and tested as friction piles founded in stiff clays and end bearing micropiles in dolomitic limestone. The results of the test were used to determine if the micropiles on the project would be installed as end bearing or friction bearing elements. Strain gauges were used in addition to conventional deflection vs. load data for the Milwaukee Auditorium Theatre project. Other aspects of the paper will include the differences in design methodology for end bearing micropiles in massive dolomitic limestone vs. design in softer, weathered limestone.

Jan 1, 2008

By Tim Siegel, III Fondren, Billy Camp

"INTRODUCTIONThe new $650 million power block at Santee Cooper’s Cross Generating Station in Cross, South Carolina is being constructed on driven pre-stressed concrete (PSC) piles. S&ME, as geotechnical subconsultant to Parsons Energy and Chemical Group, was responsible for pile analysis and design to meet the site’s geotechnical and seismic challenges. Selection, analysis and design of the PSC piles included consideration of the following:• Column and equipment support loads ranging up to 500 to 1000 kips (2224 to 4448 kN).• Incorporation of the 2000 International Building Code seismic provisions.• A thick upper soft clay and loose, liquefiable sand.• Potential for karst-related features in the calcareous Santee Limestone.GEOTECHNICAL CHARACTERIZATIONThe near-surface site geology consists of (in order of increasing depth): (1) Pleistocene sediments, (2) the Santee Limestone (considered part of the Orangeburg Group) of Eocene age, and (3) the Black Mingo Formation of the Eocene/Paleocene age (refer to the shear-wave profile in Figure 4). Pleistocene clays and silts are generally soft and will settle significantly if subjected to loading by heavy grade-supported structures while the interbedded sands are generally loose. Where submerged below the shallow groundwater table, the sands were determined to be liquefiable during a strong earthquake.The Santee Limestone is a nearly white to yellow fossiliferous and partly glauconitic rock consisting chiefly of calcium carbonate. Observations of the rock core samples from the site indicate that it can range from hard crystalline limestone (primarily in thin layers) to a lightly cemented sand. In terms of rock strength, the Santee Limestone is generally very soft to soft, depending on the cementation and other depositional characteristics."

Jan 1, 2004

By Patrick J. Hannigan

The pile foundation designer typically performs a subsurface exploration program and static pile capacity calculations before selecting a pile foundation type, length, and capacity. During construction, a pile installation criterion must be established to meet these design requirements. This installation criterion usually consists of a minimum penetration resistance or blow count to confirm pile capacity and may also include a minimum embedment requirement. This text will focus on use of wave equation analysis and dynamic measurements to meet design requirements. BEFORE THE WAVE EQUATION Since the mid-1800s, over 450 dynamic formulas for pile driving control have proliferated. In their simplest form, these formulas relate hammer energy to the work of soil resistance, or simply: W ? h = R ? s (1) Where W = ram weight h = ram drop height or stroke R = pile capacity s = pile penetration per blow

Jan 1, 1990

By Stefan Dahlin

The laboratory tests indicated low permeability but as I said, as a rule, the permeability in the field has been found to be higher. A high permeability has also been found when doing back calculations of rates of settlements in different cases. But as I also said, there's a need for further studies in this area.

Feb 10, 2003

By Bin Zhang

Drilled shafts are a popular type of foundation for transportation applications. They feature the advantages of providing high bearing capacity and generating low construction noise. Advancements in construction technology make it possible to construct drilled shaft with large diameters. In some transportation projects, the full structural loads are carried by a single large diameter drilled shaft; therefore accurately determining the bearing capacity of drilled shafts has important practical and safety implications. The increase of drilled shaft diameter combined with the structure properties of the surrounding soil play in an important role in their bearing capacity. The conventional methods for bearing capacity determination, which mostly come from experience with small diameter drilled shafts, may not work satisfactorily. This paper studies the influence of diameter on the bearing capacity of laterally loaded drilled shafts. Numerical simulations are conducted to investigate the effects of pile diameter on the lateral bearing capacity, especially the influence of shaft diameter and its structural contributions.

Jan 1, 2007

By Shaw-Shong Liew

This paper presents the processes of investigation, analysis, design, construction and monitoring of soil nail stabilisation work to facilitate a 14.5 m deep excavation at an uncontrolled fill ground. An extensive instrumentation programme had been implemented to monitor the performance of the stabilisation solution, to provide validation for the designed nail resistance and groundwater variation. From the monitoring results, it was proved that the soil nail stabilisation technique is effective for loose saturated fill provided that substantial care is taken during implementation. Construction difficulties, solutions to overcome the problems and lessons learned will be discussed in the paper.

Jan 1, 2006

By Tony Brunger, Abid O. Adekunte, George Munteanu, David Greentree

A number of novel solutions have been proposed in recent years as alternatives to props and tie-backs in deep excavation support e.g. Adekunte (2008), Deschamps et. al. (2008), Adekunte et al. (2010) and Adekunte (2014). A number of these non-standard restraining solutions involve the construction of permanent or temporary vertical or raking buttress piles that are rigidly connected to the excavation support wall at regular intervals along the wall run. This paper chiefly focuses on the design and construction of twin-vertical buttress piles as restraining systems behind or in front of embedded retaining walls. The system essentially relies on the push-pull mechanism that develops between the twin piles, to maintain the overall stability of the excavation support. The paper’s main areas of concentration include; finite element modelling, geostructural design, construction procedure, instrumentation and monitoring that are associated with the application of twin- buttress pile systems. These are supported with project details of three recently completed high-end luxurious residential developments in Greater London, England, on which the twin-buttress pile system was used to restrain the excavation support walls for the basements on the sites. The mode of application of the system varies across the three sites. While the system was adopted as a long term solution behind the retaining wall on one of the sites, it was designed and constructed for temporary use in front of the retaining walls on the other two sites. Instrumentation and monitoring results from all the sites show the non-traditional system to be safe and effective, whilst having significant beneficial effects on construction programme, sequence of works and project cost.

Jan 1, 2018

By Eric Brandner

Expansive soil formations can be found throughout the United States. When subjected to wetting, many of these formations have the potential to swell and exert large uplift forces which can significantly damage lightly-loaded structures. Designing an economical foundation that can resist uplift forces is critical to prevent damage to these structures. The current solutions to control uplift due to swelling soils, such as over-excavation and replacement of the expansive material, or drilled shafts, can be costly and problematic. Piles made from recycled polymer materials may provide a solution. Due to a lower coefficient of friction along the interface than piles made from traditional materials, solid recycled plastic piles can allow expansive soils to move nearly independently from the pile when wetted. This results in a much smaller magnitude of uplift force being transferred to the structure which minimizes the risk of significant structural damage. This paper presents the preliminary results of research conducted on the use of recycled plastic piles in an expansive shale environment. The preliminary phase of the project involved the installation of six 13 in. (330 mm) diameter recycled plastic piles at a test site on the South Dakota School of Mines and Technology campus. The piles varied in length from 15 ft. to 25 ft. (4.6m to 7.6 m). Two of the piles were subjected to a full-scale compression load test in order to determine ultimate capacity, while the additional four piles are being subjected to long-term monitoring of uplift movement. A cast-in-place concrete pile, with a diameter of 6 in. (152 mm) and length of 15 ft. (4.6 m), was also installed at the test site for monitoring. The preliminary results indicate that the use of solid recycled plastic piles is a viable alternative for support of lightly-loaded structures in expansive soil environments.

Jan 1, 2009

By Rob Jameson

"The demand for commercial and residential construction has continued to evolve across the United States over the last decade. Our markets demand larger, deeper and inherently more complex structures, located within increasingly constrained urban locations and with challenging geotechnical conditions. As project demands incrementally escalate, specialty contractors are continuously challenged to extend their state of practice. Development in the size and capabilities of construction equipment, tooling, techniques, monitoring and verification systems over the last decade has consistently allowed contractors to build larger and deeper. For support of excavation (SOE), in addition to scale, selection of the most appropriate system has been a key to success in the most challenging ground conditions. This selection process is based on sound engineering and construction practice, and also prior experience, both positive and negative. Ultimately many Owners have chosen to manage their risk of SOE construction through design-build contracts, which allows specialty constructors to optimize the balance of cost, schedule, scope and associated risk based on their local expertise. Successful implementation of a design-build methodology begins long before a contractor is selected, with identification of key project requirements and risk factors during the feasibility studies and design development phases. In these early stages of the project development, advice and budgets are frequently solicited from Specialty Contractors. The Owner, Construction Manager and Consulting Team will filter this input from multiple sources to provide their specific recommendations, develop construction documents and select the appropriate form of contracting. Only in the final stages, after award of a Design-Build Subcontract, can the successful specialty contractor directly influence risk management approach on the project. A case study is presented from Block 9 in San Francisco’s Transbay District. This project demonstrates the incremental identification, assignment and mitigation of construction risk through the planning and design build process for SOE on the deepest planned excavation in San Francisco.INTRODUCTIONThe mature urban development market in United States results in high demand for complex Support of Excavation (SOE) schemes on constrained sites. The Design-Build approach can be applied to increasingly difficult SOE challenges, combining regional specialty subcontractor knowledge and experience in order to optimize solutions for cost and schedule. The most successful applications will involve early engagement of shoring subcontractors within the project teams, during feasibility and design development stages, in order to identify key scope and risk issues, and their potential solutions. Throughout the project development, it is important to reasonably assign responsibility for construction risks amongst the project stakeholders who are best able to control them.This paper presents a case history for San Francisco’s Block 9, a well-planned and successfully executed design-build SOE project in San Francisco’s Transbay Redevelopment area. Throughout the 4 year period from the Developers initial proposal to the Redevelopment agency, through completion of excavation down to subgrade, the project team developed a series of increasingly refined SOE schemes, with corresponding scope definition and cost and schedule estimates. This program relied on early identification of key challenges and risks for the project, and evolved through multiple phases of proposals as first the General Contractor (GC) and then Specialty Shoring Subcontractor were engaged for the project. The scheme, cost and schedule refinements continued throughout construction in order to accommodate unanticipated conditions and events as they unfolded."

Jan 1, 2017

By James C. Scott

Compression and tension load testing were performed on bored concrete piles installed to depths of 18 to 34 meters below excavation levels for a large mixed-use development in Kuala Lumpur, Malaysia. The 900 mm diameter piles were installed in weathered graphitic schist bedrock. Load testing confirmed the side shear and end bearing capacities of the piles. The work formed part of the investigations for the 56,000 m2 site which includes a 79-story office tower, hotel tower, apartment tower, retail complex, and plaza area underlain by 4 to 6 basement levels. The paper provides the results of the site investigations, pile-load testing procedures, pile-load settlement behavior, and shaft load distribution.

Jan 1, 2007

By Robert Fernie

Demographics and Infrastructure demands have led to a significant increase in construction of: deep basements for buildings and, trough structures for Highway and Rail/Metro. Concrete embedded walls used for temporary works can be incorporated into permanent works and because of this (and geological conditions) tend to be favoured in UK. This paper considers British practice in the provision of diaphragm (slurry) walls secant (true and pseudo) piled walls contiguous piled walls Plant utilisation, construction techniques, reinforcement placement, connections, propping, water tightness, tolerances, general UK practices and their relation to design practices are discussed. [ ]

Jan 1, 2000

By Chandrasegaran, Tamilmani

"This paper describes a case study of a retaining wall structure using a diaphragm wall to construct a stilling basin at Tanjung Bin T4 power plant in Johor Bahru, Malaysia. The stilling basin is part of the Phase IV (T4) 1x1000MW power plant’s offshore cooling water discharge culverts. The site is located close to the sea with 5m of fill on top of very soft sediments of marine origin up to 20m thick underlain by fluvial clay and metasedimentary rock. Stringent wall deflection criteria and construction program dictated adopting an efficient solution with 800mm thick diaphragm wall supported by permanent top support as the temporary prop and improved horizontal restraint provided by deep mix piles acting as a slab (ground improvement layer) below the final excavation level. The depth of excavation is about 10.12m from the existing ground level. The proposed solution kept the wall deflection below the limit of 0.7% of the depth of bulk excavation and avoided additional props leading to faster completion of the structure. With unsymmetrical loading behind the retaining walls, 2D finite element analysis was carried out to assess the wall deflection and stresses in the wall and the grout layer below. The diaphragm wall is instrumented to monitor the behavior and the findings are discussed in the paper.INTRODUCTIONConstruction in soft marine clay has always been a challenge to the engineer because of its very low shear strength and its sensitivity to disturbance. In the case of excavation projects the problem becomes even more complicated with development of excess pore pressure during excavation. Marine clay with its low shear strength and lesser passive resistance, generally leads to large wall movements and settlement behind the wall. Increased passive resistance coming from increased number of props is useful but has its limits and it is no longer the most effective way in containing or reducing the wall movements or forces in the wall. One of the solutions to these problems is to improve the soil shear strength by means of ground improvement infront of the wall at an elevation most appropriate to maximize wall performance. There are several methods adopted in improving a soil layer including mixing additives to the ground to improve the shear strength to partially replacing the weak soil while others are fully replacing the weak soil. This paper discusses the case study of approximately 10m of excavation in soft marine clay using 800mm thick diaphragm wall supported by Deep Mix Piles (DMP) being used to improve soft marine deposit to form a slab just below the formation level and thus improving passive resistance significantly. The ground improvement layer helped to reduce the wall forces and deflections making it possible to remove the need for additional temporary props leading to significant savings is time and productivity. The paper presents the various options explored before this method is adopted, the design approach, instrumentation data and the monitored results."

Jan 1, 2015

By Salim Mezazigh

Usually different methods for designing a single pile submitted to a lateral loading are available. They are based on theory of elasticity with the parameters E,v or subgrade reaction method using the p-y curves. The subgrade reaction methods are commonly used. They allow determining the efforts exerted along the piles and their corresponding displacements. Before any design the reaction curves P-y must be well defined for each foundation soil layer. These curves link the pile horizontal displacement y to the subgrade reaction of soil P. Different in situ tests such as the static penetrometer or the pressuremeter give a possibility to get the P-y curves in the case of a single pile installed in sand with an horizontal surface and statically laterally loaded. These ideal conditions are not always respected on the site around the pile if appear slopes, embankments, or buildings... The behaviour of such configurations of piles is more sophisticated due to the proximity ( slope, embankment, earthworks, buildings,..). A research program has been conducted to determine the influence of a slope on the P-y curves by centrifuge modelling. The centrifuge tests constitutes an experimental approach allowing parametric studies in respect with similitude laws in geotechnique. Before all, repeatable tests have demonstrated that the test conditions, the instrumentation equipment and the installation method for piles are well controlled. By this way, the obtained results from centrifuge tests can be transferred to the prototype i.e. the in situ piles. Many tests have been performed on piles in sand to determine the influence of a pile on the p-y curves. The main objective is to give for practice some coefficients to apply to p-y single pile curve to take into account the proximity slope effect. Here the experimental set up is described and in particular the proximity slope effect is discussed. Deduced subgrade reaction reduction factors are proposed for piles in sand under lateral loading.

Jan 1, 2002

By Richard Short

Shallow rainfall-induced landslides in residual and colluvial hillslopes and steep embankments are a common occurrence in many settings [1, 2, 3]. While occasionally posing a threat to property and life-safety, they more often present an ongoing maintenance problem and can lead to the initiation of larger failures. Typically, these slides consist of 2 to 4-foot thick translational movements of silty and clayey soils down slope through the reduction of strength from increases in pore water pressures. Direct surficial infiltration and indirect groundwater seepage are the normative triggers for failure. In the residential community of Blackhawk, California, located east of the San Francisco Bay, these types of landslides are a common occurrence (Figure 1). However, shallow landslides have also been a repetitive and constant problem along many state highways where steep embankments have been constructed in close proximity to busy thoroughfares. Given the real threat to property values in residential and commercial settings and the constant maintenance problem posed to lifeline structures such as utilities, roadways, and pipelines, new methods to deal with these landslides are needed.

Jan 1, 2007

By Shachar Magali

This article describes two new concepts regarding the CFA (Auger Cast) piles. The first one, MALI Effect, is an approach to control the casting phase, while the second one, NETA Shear, is a technique which converts the drilling rig into a geo-mechanical tool. We look upon the system of the auger and the ground as a piston inside a cylinder. When concrete (grout) is pumped into that system, an up lift force is generated (We call that force MALI Effect). That up lift force reduces the needed tension in the pull up cable. By analyzing the tension force in the cable we detect the up lift force of the concrete. That pushup force is the product of the real concrete pressure at the bottom of the auger by the area of that bottom. As the area is known, the real pressure is accurately calculated. A control loop which is based on MALI Effect is very sensitive, precise, objective, reliable and easy to be used. All the process is based on pure real physical measurements. The system has no assumptions, no comparisons, no parameters, no zeroing and no adjustments. When we penetrate into the ground like a theoretical screw, for about a meter in depth, and then brake the main cable while rotating the auger, a set of forces generates. As the auger tends to keep penetration, but the cable holds it - a tension force develops (We call that force NETA Shear). Analysis of that tension force shows that it relates to the ultimate shearing capacity of the ground.

Jan 1, 2000

By Safwan Labanieh

An experimental set-up is specially designed to study the behavior of a friction pile of 3 cm diameter in contact with the soft clay of Mexico City in a small calibration chamber (CC) of 30 cm diameter and 50 cm height. The consolidation of this compressible clay is accomplished using a special system adapted to the CC itself to insure a good knowledge of the initial state. Loading results of the pile under a consolidation pressure of 50 kPa indicate an elastic mobilization of shear stresses at the shaft of the pile (?3 kPa for 1mm displacement) followed by a hardening plastic type behavior. Unloading-reloading results indicate a mobilization of shear stresses of the same type and of the same order of values obtained from the virgin loading stress path. Cyclic loading (?40 cycles) between 0 and 1 kPa (1/3 of the failure value) give similar results to those obtained from virgin loading.

Jan 1, 2002