Search Documents

By C. Guney Olgun, Charles Elks, Sherif L. Abdelaziz, James R. Martin, Christopher Fox, Pier Luigi Iovino, Fatih Catalbas, Pierre Gouvin

"Energy piles are a new innovative renewable energy technology to access and exploit the relative constant temperature of the ground for efficient heating and cooling of buildings. Examples of energy piles include drilled shafts, continuous flight auger (CFA) piles, driven piles, and micropiles. A field test setup was installed at the Virginia Tech Geotechnical Research Facility to study energy piles. The field test consists of a total of five micropiles 25 cm (10 inches) in diameter, four of which were equipped with circulation loops. The test piles extend to a depth of 30.5 meters (100 feet) and are heavily instrumented with strain gauges and temperature sensors. Several observation boreholes were formed around the test piles to monitor ground temperatures. Thermal conductivity tests and field load testing were performed to investigate the behavior of Energy Piles. This paper presents results of the thermal conductivity tests and thermo-mechanical field load test performed as part of this field investigation.IntroductionThere is a developing trend around the world to explore alternative energy sources. The main driving forces are growing global energy demand, depleting natural resources and the adverse effects of greenhouse gas emissions from fossil fuel consumption. Geothermal energy is one of the promising renewable sources that can be utilized to offset such trends. However the use of geothermal energy has been limited mainly to certain hot spot areas where it is used either for district heating and/or electricity generation. Ground temperatures below a depth of about 6 meters (20 feet) remain stable compared to outside air temperatures, typically lying between 8-23°C (46-73°F) at most U.S. regions. The constant temperature and heat storage capacity of near surface soils in any region represent a tremendous potential of stored energy that can be used for heating and cooling of structures."

Jan 1, 2017

By Heinrich Majewski, Rob Jameson

"Careful review of site conditions and constraints is essential to select the appropriate shoring system for each project. Key evaluation criteria include the geotechnical profile, groundwater and environmental conditions, adjacent buildings and utilities, schedule and any project specific access or other constraints. Typical earth retention schemes range from rock or soil nail walls, through conventional anchored pile and lagging walls to deep internally braced cut-off systems. The Owner’s design team will often develop the conceptual approach under their design studies, and this is refined with Contractor input through Design-Build or Design-Bid-Build procurement. In downtown San Francisco, underground construction must accommodate a unique combination of variable fill, soil, rock and groundwater conditions, potential for severe seismic loadings, and constrained sites within a dense urban environment. The quarter square mile of San Francisco’s Transbay and Rincon Hill districts has seen repeated cycles of development, destruction and re-building through earthquakes and the economy, and has been intensely redeveloped over the last decade. Over 50 acres of this land has been reclaimed from the Bay since the Gold Rush and within 3 city blocks the bedrock slopes from over 250 FT depth below the fills up to outcrops over 100 FT above sea level. A series of project examples from within this small area illustrate how varied shoring systems have accommodated the highly variable subsurface conditions while offering best value in terms of cost, schedule and appropriate protection of adjacent facilities.INTRODUCTIONA walk of 3 blocks from Rincon Hill on San Francisco’s Harrison Street, north through the Transbay area to Mission Street will traverse an urban zone which has been reinvented twice within its 150 year history in response to major seismic events. This small area highlights the range of subsurface conditions and urban environments which are encountered and accommodated in shoring schemes throughout the city. This route down the north side of Rincon Hill overlies a steep bedrock slope, outcropping over 100 FT above sea level at its south end and dropping to over 250 FT below sea level at Mission Street. A complex overburden soil profile, shaped by seismic activity and changing sea-levels has created layered soils ranging from soft estuary muds, dense sandy strata and deep clay layers, in turn topped with urban fill, frequently contaminated with debris from the Great 1906 earthquake. This route runs parallel to, and 350 yards inland of, the San Francisco shoreline resulting in groundwater elevation close to sea level with almost limitless recharge within granular layers. On the higher slopes of Rincon Hill, groundwater is typically observed flowing on top of and periodically within the fractured bedrock formation. The Transbay and Rincon areas were developed early in the Gold Rush era of San Francisco. After destruction in the 1906 earthquake and fire, they became a transit gateway into the city throughout the 20th Century. Demolition of the Embarcadero Freeway in response to earthquake damage and social pressure has opened this large area to redevelopment within the last 20 years, creating a new commercial and residential hub for the city. In its latest wave of building, planners are developing taller structures with deeper basements, in turn creating new construction challenges. Selection of shoring systems appropriate for these developments requires detailed evaluation. The process must address both the rapid spatial changes in subsurface conditions and the constraints surrounding, and specific to, each site in order to define shoring performance requirements. This paper presents an overview of the subsurface conditions and land use development of the Transbay and Rincon Hill areas, with examples of the shoring systems selected to meet site-specific conditions and requirements. The projects cited range from soil nail wall"

Jan 1, 2017

By A. David Miller, Chika Oya

"Field sampling and testing are part of the Quality Assurance/Quality Control (QA/QC) requirements for all Cement Deep Soil Mixing (CDSM) Projects. Field sampling and testing are also used for determining the performance and quality of soil mixing method(s) and are the primary basis for accepting or rejecting the soil mixing wall among all other QC testing. Two of the most commonly recognized and used sampling methods for CDSM walls are wet grab sampling and verification coring. Depending on the types of wall construction and project budget, one or both of these methods are normally used to help evaluate the in-situ matrix and quality of the mixed soils. Additional to ASTM strength and permeability testing from wet grab sampling and verification coring, more and more testing methods are being employed and accepted. However, these other testing methods tend to be unnecessary, lack consistency and repeatability, and are more subjective to manipulation and interpretation. In certain projects, there are also misconceptions involved with the results of wet grab sampling and verification coring, hence it is important to note how these wet grab sampling and verification coring work and represent the work in terms of quality of production.TYPES OF PROJECTSCDSM projects include (but not limited to) in-situ stabilization, liquefaction mitigation, excavation support, groundwater cutoff, and pollution containment. Although these projects use similar equipment on the jobsites, each project is treated differently in terms of catering to specification, uses of different mix designs, and emphasis on certain steps during production.Different types of projects with different specification changes the focus of quality, but soil types in jobsite also determine how to proceed with production. For example, a jobsite with predominate gravel layer must be treated differently as opposed to jobsite with clayey sand as the main soil type.WET GRAB SAMPLEWet grab sampling is one of the most used testing methods for QA/QC. The wet grab sample specimen is retrieved right after finishing the production of the desired element.Wet grab sampling equipment consist the use of 28 cubic inch (458.84 cubic cm) box attached directly to one of the auger stems. Hinges attached to the top and bottom of the box is fabricated to allow collection only during auger withdrawal. The collection box is strapped just above the mixing paddles on the auger stem and measured from the center auger head tip to confirm proper depth of collection. This box method has been used in Japan and U.S. for numerous projects."

Jan 1, 2017

By Lok M. Sharma

"Construction of a new bridge in a seismically sensitive area requires careful assessment of earthquake impact on the serviceability of the facility. Not only is the superstructure vulnerable, the foundations play a key role in the bridge’s survivability. A new bridge in eastern part of the state of Missouri in the U.S.A. is located in a seismically active area and hence subject to additional thrust on the foundations and superstructure and potential damage due to liquefaction. An eleven span bridge with foundation soils varying from shallow bedrock to over 30 m (100 feet) overburden soils were considered for the bridge support piers. Two of the bridge support bents located within the flood plain area through over 30m (100 feet) of alluvial deposits were considered most affected by an earthquake event due to the additional thrust and lateral ground spreading. This paper describes the determination of site specific seismic hazard, numerical modelling of the foundation system, and methodology of dynamic analyses, effects of lateral spreading and liquefaction potential on bridge support bents. From numerical modelling using FLAC, the increase in thrust on piers and deformations were computed to predict the behavior of the foundations.INTRODUCTIONA newly constructed bridge on route US 40 crosses the Missouri River west of St. Louis, Missouri and upstream of Mississippi River in mid-west USA. The west abutment area has near surface bedrock while the east abutment area has overburden deposits over 30m (100 feet) thick, mostly river sediments comprising of silts, lean clays and sands overlying bedrock. Softer layers of silts and sands in the east river bank area are assessed to be liquefiable during a high magnitude earthquake event. St Louis area has a potential for a high magnitude earthquake due to the New Madrid Fault some 160km (100 miles) south. The bridge foundations were designed as drilled piers, 2 m (8 feet) in diameter and socketed into the bedrock. Bents No. 10 and 11, located in the lower flood plain area of the river, are considered to be most affected by a seismic event.In order to perform dynamic analyses of the foundations, earthquake ground motion time history was developed for the specific site using a Probabilistic Seismic Hazard Analysis (PSHA) and selecting and scaling of a recorded time history. Relying on the U.S. Geological Survey (USGS) Earthquake Hazard Program for the PSHA and AASHTO Guide Specifications for LRFD Seismic Bridge Design, spectral acceleration values for the site were developed. The spectral acceleration values were for a 7 percent probability of exceedance in 75 years (1000 year return). Numerical modelling using FLAC computer program was performed. This paper presents the seismic design parameters, methodology used in the dynamic analyses, static and dynamic analyses, impact and mitigation of liquefaction on Bents 10 and 11 and the abutment fills, and effect of lateral spreading on the foundations in the lower flood plain area of the bridge. From the numerical modelling, increase in thrusts on pier foundations and estimated deformation were computed."

Jan 1, 2017

By Arpit Parikh

"Ground Water or Pore water pressure development in Sandy Soil formation is Critical situation in foundation analysis and design.Moreover it become severe while associated with higher liquefaction probability in river bank areas. It is difficult to find cost optimized solution for liquefaction mitigation under limited budget allocated for the project. Here in these research paper the attempt has been made to have clear picture of liquefaction by using various techniques and field tests. And its mitigation by suitable foundation type. In Bangladesh, On Bank of River Meghana, Power plant structures are proposed. The particular site is full of fine sand having partial silt throughout from EGL to 55 m depth. Hence in addition to Conventional Boring / Drilling operations, CPLT, SCPT, SCHT and PMT had been performed to arrive deterministic effect of liquefaction. By use of Geologismiki software and some excel based programs developed which indicates that Certainly liquefaction occurs under the event of earthquake. By Checking past records of Bangladesh we found, there are small magnitude earthquakes are inevitable and frequent. Hence fourth to overcome the bad effect of liquefaction, the deep pile foundation -Driven Pre Cast Solid Square Pile of 400 mm dia. had been suggested for various types of power plant structures. Which densify the soil and ground will improve in resisting liquefaction.1. INTRODUCTIONA Detailed Geotechnical/Foundation design Analysis had been done to arrive at optimum foundation design solution in highly probable liquefaction zone of Silty Fine Sand near Dhaka City of Bangladesh for proposed 750 MW Cyclic Power Plant. Hence about 24 no. of (Borehole) Boring and Drilling up to depth of 55 m from existing ground level has been carried out. Additionally, 09 nos. of Static Cone Penetration Test (SCPT), 02 Nos. of Dynamic Cone Penetration Test (DCPT), 02 Nos. of Pressure meter test (PMT), 02 nos. of Cyclic Plate load test (CPLT) of suitable capacity with 06 nos. of Seismic Cross Hole Test (SCHT) in boreholes had been carried out. The purpose of PMT and SCHT was to have clear idea about the Seismic behavior - knowhow of site. According to Basic principles of Soil Mechanics and foundation design, it is proved that PMT & SCHT are dynamic test. These tests stimulate field condition of occurrences of earthquake. In later stages of analysis, it is found that site have high probability of liquefaction through use of Geologismiki – Liquefaction Analysis Software. Author of these research paper also felt earthquake vibrations – strong aftershocks during site study where Epicenter of the earthquake was in Myanmar during month of august 2016."

Jan 1, 2017

By Aminul Islam, Vinay M. Kumar

"About 100 Hectares of land reclamation over the very soft to soft marine clay at Uran Creek in Maharashtra is planned. The depth of marine clay varies from 10m to 24m as observed from the geotechnical investigation. The marine clay was treated with Pre-fabricated Vertical Drains (PVD’s) installed from the elevation of +5.5mCD (chart Datum) and preload/placement of surcharge. A Settlement of soft soil mud under the reclamation was monitored using magnetic extensometer (M) and ground settlement maker (S2). These instruments are installed after constructing working platform at around +5.5m CD. Based on the field instrumentation data, the consolidation parameters were adjusted to match the theoretical and actual settlement plot. The author called this approach as “Back analysis method”. The objective of this paper is to present a case study of instrumented preloading treatment for a thick marine clay deposit. The degree of consolidation in clay strata was determined from magnetic extensometer and ground settlement marker data. Authors also determined degree of consolidation as Asaoka method, Hyperbolic method and Back analysis method and compared the results.INTRODUCTIONExpansion of Container terminal with port buildings, rail container depot, roads and utility buildings at Jawaharlal Nehru Port Trust (JNPT) is planned over a reclaimed land of 100 hectares. Uran creek predominately consists of the estuarine deposit of very soft to soft marine clay. They are characterized by low shear strength, very low bearing capacity and exhibit large settlement when subjected to loading. The additional load causes the significant magnitude of consolidation settlement over a considerable period of time. Thus for development projects on top of soft soil, the postconstruction settlement would be of primary concern.To accelerate the consolidation pre-fabricated vertical drains (PVD) were used. Pre-loading procedure was adopted to minimize the post construction total and differential settlements. PVD’s were installed at 1.0m and 1.2m c/c triangular pattern. Locally available borrow material is used as a reclamation material. The reclamation material has been placed over the existing sea bed level by land based method/end tipping method and created the working platform. The level of working platform is decided based on the tide data and it has been selected such that work should be affected during highest high water level. The PVD has been installed from the working platform and subsequently all the field instruments have been installed from the same level. Five different types of field instruments are installed to monitor ground improvement works."

Jan 1, 2017

By Shuvranshu K. Rout, Anup K. Mandal, Biswajit Das, Manos De

"To adopt new technology advancement in Steel Plant, there is a requirement of shifting of operation process from Coke Wet Quenching (CWQ) to Coke Dry Quenching (CDQ). New CDQ chamber foundation with deep basement and underground conveyor tunnel are to be constructed in an operating plant where heavy foundations and structures are located in close proximity. Furthermore, the existing CWQ system will be in operation during new underground construction and erection. Challenges to deep excavation of tunnel and chamber foundation consist of non-uniform ground condition, prevent washing out of soil from bottom of existing foundations, stability of existing nearby structures, presence of large number of underground utilities, ensuring safe underground workplace to construction resources engaged in new construction work along with project schedule and budget constraints. A combination methods involving use of soil nailing, soil grouting, contiguous bored pile and micro pile had been adopted for protection of excavation sides as well as existing structures. Each side of excavation in different stretches were analysed during design as well as construction stages. The use of combination of all techniques in a single brown field project in context of the nature of site constraints and safety issues made this a unique project.INTRODUCTIONSteel Industry is one of the backbones of industrial growth of any developing country like India. Due to increasing land prices most of the steel plants in India are expanding within their existing plant facilities. In addition to that, there is demand of adoption of new technology for future expansion projects to set new benchmarks with global standards.The property owner had earlier installed a Coke Wet Quenching (CWQ) for their Coke Plant. Now, there is a requirement from process department to proceed with Coke Dry Quenching (CDQ). To facilitate the CDQ within the existing CWQ which will be in operation is the main challenge for the property owner. The second challenge is the limited space for underground construction and subsequent equipment erection within the stipulated time frame.From a geotechnical prospective, the project team had uncertainty and reservations in their mind about the construction methodology. Therefore, the role of three “C”: ‘Consultant’-‘Client’- ‘Contractor’ and their combining brainstorming is essential to freeze a working plan for achieving the goal. In this paper, only the excavation support systems for underground foundation structures have been highlighted in the context of solving geotechnical problems."

Jan 1, 2017

By Swaminathan Srinivasan, Jess A. Schroeder

"Landslide activity along U.S. 50 in Cincinnati, Ohio (USA) has caused roadway damage for decades. After a necessary closure of three lanes due to slope movements, emergency stabilization measures were undertaken to protect the roadway by providing a short-term solution necessitated by The Ohio Department of Transportation budget constraints. The landslide shear plane occurred on a sloping bedrock surface as much as 50 feet below grade. Drilled shafts were installed 40 feet downslope of the roadway shoulder and were heavily reinforced across the shear plane but steel reinforcing did not extend the full length of the shafts and was stopped well short of the ground surface. Instrumentation data has been collected for 11 years after construction has shown these “Stub Piers” have provided much more than a short-term solution and have provided an attractive alternate to conventional deep shafts or tieback drilled shaft options.INTRODUCTIONLandslide activity has occurred along U.S. Route 50 in western Cincinnati, Ohio for many decades. The site is located between North Bend and Addyston, Ohio on the right descending (cutting) bank of the Ohio River. Road distress caused by slope movements required periodic repairs over recent decades. Railroad tracks downslope of the roadway also showed signs of horizontal displacement and periodic repair. Visual evidence in 2005 suggested the shear plane extended below the US 50 roadway and extended out into the Ohio River.A weed and brush-covered slope extended down slope from the roadway at about 3H:1V for a vertical distance of about 20 feet. Above US 50, the hillside continued to rise more than 100 feet. There is a railroad right-of-way at the toe of the slope with the Ohio River bank just downslope of the railroad.In 2005, Terracon Consultants was retained by the Ohio Department of Transportation (ODOT) to perform a geotechnical study that included 17 test borings and inclinometer monitoring at 4 locations. Roadway damage was occurring (see Figure 1). After only a few weeks of monitoring, the inclinometer casings sheared off about 50 feet below grade, near the soil / bedrock interface (see Figure 2). Soon after, the roadway distress worsened, causing ODOT to close 3 of the 4 lanes to traffic and reroute traffic onto the remaining single lane and shoulder. Terracon was asked to develop a stabilization design under emergency repair conditions. However, both limited budget and time-related constraints necessitated a direction by ODOT that the solution be at least “pseudo” short-term (3 to 5 years)."

Jan 1, 2017

By B. Soundara, A. Suganya, S. Selvakumar

"Expansive soils have a potential for shrinkage or swelling under changing moisture content. Attempts were made to reduce the swelling potential of expansive soils with conventional additives such as lime, cement, etc. and non-conventional additives such as industrial wastes. In this research an attempt is made to study the feasibility of using granulated waste expanded polystyrene (EPS) as an additive to expansive soil to control swelling. To investigate the effect of mixing waste EPS granules with expansive clays, three expansive soils with different plasticity index were manufactured in the laboratory by mixing sand with sodium bentonite of various proportions. A series of standard proctor test, California bearing ratio (CBR) test, one dimensional free swell and swell pressure tests were performed on these soils. Test results show that the inclusion of EPS granules significantly reduces the percent swell and swelling pressure when subjected to one-dimensional free swell conditions. The dry density and CBR values decrease with increase in EPS content and increased plasticity of the soil.INTRODUCTIONExpansive soils cover an area of about 257 Million hectares on the earth’s surface (Dudal et al. 1965). In India, the area covered by expansive soils is nearly 20 percent of the total area (Mohan et al. 1961). Movement is usually in an uneven pattern and of such a magnitude as to cause extensive damage to various structures, especially lightly loaded structures or pavements (Chen 1975). Stabilization is one of the methods of treating the expansive soils to make them fit for civil engineering purposes. The variety of stabilizers may be broadly divided into three groups (Petry et al. 2002): (a) traditional stabilizers (lime, cement etc.), (b) by-product stabilizers (fly ash, quarry dust, phosphor-gypsum, slag etc.) and (c) non-traditional stabilizers (sulfonated oils, potassium compounds, polymer, enzymes, ammonium chlorides etc.). Apart from these, a number of other ground improvement techniques such as sand cushion technique (Satyanarayana 1966); cohesive nonswelling (CNS) layer technique (Katti 1978) were adopted for the stabilization of expansive soils. Expanded polystyrene (EPS) is a polymeric foam normally available in white colour and is a wellknown packaging material. The geotechnical specialists recognize EPS as the most commonly used geofoam material, a type of cellular geosynthetic which has been in consistent use in geotechnical applications since the early 1960s (Horvath 1995). EPS has very low thermal conductivity and nearly 98% of the volume is air (Lye et al. 2002). EPS has many exceptional properties such as being lightweight, thermal insulating, shock-absorbing and having low-water pick-up, etc. EPS find its applications in geotechnical engineering as light weight fills in the form of blocks (Refsdal 1985, Karpurapu et al. 1992, Zou 2001, Ikizler et al. 2008). EPS can be used as compressible inclusion and as a vibration damper (Horvath, 1994&1995). EPS is also used in lightweight concrete owing to its lightweight, excellent heat preservation and sound insulation properties (Ravindrarajah et al. 1994; Miledet al. 2004 and Babu et al. 2005). Waste EPS granules have been used in with horticultural soils to improve a number of soil characteristics like improving drainage, lightening heavy soils and improving water uptake capacity of soils (Scheirs 1998). Furthermore, it was also used as sub-base materials for pavements and railway track beds (Hanna 1978; Duskov1996), construction materials for floating marine structures and fenders in offshore oil platforms (Bagon et al. 1976), sea beds and sea fences; as an energy absorbing material for buried military structures, (Perry et al. 1991)."

Jan 1, 2017

By Hayel M. El-Naggar, Marawan M. Shahien

"Large capacity piles are important type of foundation elements that are needed in case of high column loads such as in tall buildings with large span between columns. In many projects, especially if the designer uses the concept of one pile supporting one column (Hamza, 2003a & b). The axial capacity of the large bored deep foundations can be further increased by grouting the shaft skin and the base of the pile. The increase in the capacity of the piles due to grouting can be tremendous. Thus grouting appears as an ideal solution for achieving more reliable foundation and greater savings (Littlechild et al., 2000). A data base of pile load tests of instrumented grouted piles is under development in a major study aiming to propose a simple method to estimate the axial capacity of large bored grouted piles. The data base include pile load tests from projects constructed in Egypt and abroad. The main goal of this paper is to analyze pile load test(s) from one project. The tested deep foundations included 1.2 m diameter and 1.5 m diameter piles and a barrette of size 1.0mx2.8m. The instrumentation of the tested piles and barrette allowed for the separation of skin friction and base contributions to the axial load. Further, the contribution of the skin friction of every layer along the pile shaft could be identified. The results of the analysis clarified how base and shaft grouting increased the axial capacity of the pile and decreased the settlements for certain load level compared to conventional un-grouted piles installed under similar conditions.INTRODUCTIONIn recent years, significant research has been carried out to develop new techniques which are suitable to withstand problems in major projects such as high applied loads in high rise building, large spans structures projects and structures designed using the concept one pile supporting one column (Hamza, 2003a & b). Base and shaft grouting of piles are one of these new techniques which aim at decreasing the settlements and increasing the capacity of the pile under axial load that became major requirements in large projects (Stocker, 1983; Mullins et al., 2001; and Hamza, 2015).Base grouting consists of injection grout under pressure at the base of the pile after the concrete is sufficiently hard. Field evidences showed that the ultimate end bearing of base-grouted piles could be as high as 1.5 that of non-base-grouted bored piles (Suckling and Eager, 2001). Further, field evidences was provided by Shahien and El-Naggar (2015) that showed an increase in end bearing resistance due to base grouting reached to 2 to 3 times that of non-base-grouted bored pile. On the other hand, shaft-grouting causes increase in the soil density in the zone which had been disturbed by the pile construction and thereby improves the shaft resistance of the pile. Field measurements by Gouvenot and Gabaix (1975), Stocker (1983), Robson and Wahby (1994), Troughton and Stocker (1996), Byrne et al. (1998), Joer and Randolph (1998), Hamza and Leoni (1998), Littlechild et al. (2000), Hamza and Ibrahim (2002), Hamza (2003 a&b), Hamza (2015) and Shahien and El-Naggar (2015) showed that the shaft resistance of grouted piles could be nearly 1.5 to 5 times that of non-grouted piles."

Jan 1, 2017

By Phil Wilkinson, Sam Whitaker

"The installation of large (XL) diameter monopiles offshore typically requires expensive and specialist plant, equipment and vessels. Due to the increasing size (weight, diameter and length) of the foundations, in order to mitigate installation risk, the use of large diameter drills is becoming an increasing requirement.Project developers often try to avoid drilling operations due to the time associated with the drilling process. This restricts projects in terms of location and it also overlooks the additional engineering benefits drilling can bring to monopile foundation design e.g. reduced foundation material and better fatigue design life.By comparing the lessons learned of three milestone overwater drilling projects; methods of maximising drill speed and decreasing drilling process time is established. Particular emphasis is put on pile internal relief drilling in a process known as Drive-Drill-Drive (DDD).The milestone overwater drilling projects are North Hoyle Offshore Wind Farm (OWF) (2003); Flamanville EPR cooling water outlet shaft (2008); and Gwynt-y-Mor OWF (2014).By evaluating the effect of foundation pile diameter on drilling process times, example foundation installation costs are derived and used to show that incorporating drilling as part of a process may not be cost prohibitive to projectsContinued advances in drill technology, and drilling rates of penetration, combined with an integrated approach to foundation design, challenge whether hammering only is always the optimal solution for XL monopile installation."

Jan 1, 2017

By Amy B. Cerato, Shawn Allred, Tatiana Vargas

"Helical piles are deep foundation elements that resemble, and are installed like, a large steel soil screw — they have a slender steel shaft with one or more round helix bearing plates welded to the shaft to provide support to the structure they hold. Helical piles are rotated into the ground with a large torque motor and provide support through soil bearing on the helix bearing plates and along the shaft. The piles are available in many lengths and, due to their small footprint along with their ability to create minimal disturbance to surrounding structures, they are often used in urban settings for foundation repair, retrofitting existing buildings and for new construction projects. Helical piles are routinely installed as foundation elements in seismically active areas, such as New Zealand, Japan and the U.S.Anecdotal observations (e.g., from New Zealand, Japan and the U.S.) have shown that piles with a comparatively small cross-section and high anchoring capacity, such as helical piles, are beneficial for seismic resistance. This is presumably due to the pile’s slenderness, higher damping ratios, ductility and resistance to tipping uplift. In New Zealand, it was observed that helical pile foundations fared much better than driven and drilled concrete piles after the 2011 Christchurch earthquake. In a personal communication, Woods (2016) described that, out of the 300 structures in center city Christchurch that were supported by helical piles, fewer than 10 structures suffered significant structural damage. However, many structures supported by driven and drilled concrete piles were damaged to such an extent that they were condemned and subsequently demolished."

Jan 1, 2017

By M. Melih Demirkan, Juan J. Gutierrez, Raghav Ramanathan

"As the capital of the United Arab Emirates (UAE), Abu Dhabi is one of the world’s fastest-developing cities. To sustain its significant growth rate, Abu Dhabi must surmount challenging engineering problems in the most efficient manner. One of the challenges facing Abu Dhabi is ground settlement caused by poor groundwater control practices in inherently difficult subsurface conditions. For construction projects in Abu Dhabi located near the Arabian Gulf, groundwater is frequently encountered and must be accounted for and addressed during design and construction. Abu Dhabi City CenterRecently, the Abu Dhabi government developed a geodatabase by digitizing, processing and qualifying an extensive amount of existing information (i.e., more than 26,000 borehole logs). Because of the evaluation and processing of the geodatabase, detailed maps of geotechnical and hydrogeological surface features were generated using 3D modeling. Ultimately, the geodatabase was used to develop risk maps indicating geohazards, such as sabhka (or salt flats), uncontrolled fill and cavities. This information identifies the location and extent of the areas vulnerable to surface subsidence. Dewatering can change pore water pressure, which, in turn, alters the effective vertical stress in a soil mass and can affect groundwater chemistry. Changes in pore water pressure and groundwater chemistry can significantly affect soil and rock. The potential effects of dewatering include:• Change in effective stresses and shear strengths in soils• Increase in seepage velocities and pressures• Erosion or transport of soil particles and piping• Settlement• Collapse of subsurface cavities or voids• Transport of groundwater containing contaminants• Dissolution of soluble materials, such as rock salt or gypsum"

Jan 1, 2017

By SungJe Chi

Intrinsic remediation is the effect of natural attenuation mechanisms - dilution, dispersion, sorption/precipitation and biodegradation - reducing contaminant concentrations in ground water to specified levels at predetermined compliance points in the aquifer. Current monitoring and modeling for post closure was used to assess the current and long-term potential of intrinsic remediation of contaminated seepage originating from a large reactive (sulfidic) tailings impoundment near Questa, New Mexico. It is concluded that the natural attenuation mechanisms of precipitation within the tailings (as a result of buffering) and dilution/dispersion within the aquifer are currently active and likely sufficient to reduce contaminant concentrations to below state standards in the long-term. Other natural attenuation mechanisms such as sorption and biodegradation within the receiving aquife4s) were not assessed here, but are likely further reducing contaminant concentrations. Active interception and recovery of the seepage water is being maintained until monitoring demonstrates that intrinsic remediation has successfully achieved the level of water quality control required.

Jan 1, 2017

"Every year during the Transportation Research Board (TRB) Annual Meeting in Washington D.C., the Federal Highway Administration (FHWA) National Geotechnical Team (NGT) takes time to talk about what we are doing in research, training development and policy support. At times, I have jokingly referred to it as the State of the Program Address, but we do see it as an important opportunity to update our transportation partners on priorities and needs for the program.This update is really a snapshot of the program during the previous year, with a look at projects that are currently active. Activities undertaken by the NGT are funded from multiyear roadmaps maintained by the FHWA program and research offices, and reflect trends and opportunities affecting and influencing transportation geotechnics now and in the future. The roadmaps identify activities in research, development, guidance, technology transfer and training that will be accomplished by the NGT through and beyond FY 2020 in eight broadly-defined focus areas: • Extreme events, geohazards and sustainable geotechnics• Performance management• Reliability-based design and construction• Advanced geotechnical modeling• Alternative delivery methods• Design and construction optimization• Site characterization• Quality assuranceThe process to identify focus areas and to develop activities that will be addressed by the NGT is guided and informed through input from the FHWA NGT members, and considers feedback and input from State Departments of Transportation (DOTs), FHWA Division offices, industry and academia. This process is revisited annually to review not only the activities that are currently funded, or will be funded, but also to review the relevance of the focus areas with respect to the future needs of the FHWA, State DOTs and the transportation community.In 2016, the NGT was successful in delivering several products that will advance the state of the practice and that better support policy. Products developed included research reports, design and construction guidance, and training courses. In 2017, the research and program offices will continue to work on projects that fit within our prioritized plan and that positively impact the geotechnical community as a whole. A listing of recently completed and currently active projects is provided below."

Jan 1, 2017

By Nadir Ansari, Brian W. Wilson, Marina S. W. Li

"A hybrid shoring system consisting of cast-in-place soldier piles with Cutter Soil Mixing (CSM) infill panels was constructed for temporary support of a 19.8 m (65 ft) deep excavation in Vancouver, British Columbia, Canada. Deep Mixing (DM) was completed up to 9.7 m (32 ft) in fill, peat, wood waste and clayey silt with embedment in dense till, and soldier piles constructed through the dense till extending to below final excavation level. Two trial CSM panels were installed ahead of production to assist with developing the termination criteria of the CSM panels in the dense till. The constructed depth of the CSM panels was based on interpretation of real-time monitoring data obtained through the Bauer B-tronic system. Inclinometer monitoring data from two CSM panels and two soldier piles, as well as soldier pile survey target data was used to assess and monitor the performance of the hybrid shoring system throughout bulk excavation. The objectives of this paper are to provide an overview of the design and construction aspects of the hybrid DM shoring system and to present inclinometer and pile target data to demonstrate the lateral performance of the CSM infill panels and soldier piles. This paper also discusses the merits of using real-time monitoring data as part of the engineering decision-making process for validating CSM panel construction. BACKGROUND A hybrid DM shoring design was recently completed for a high-rise development in downtown Vancouver, British Columbia for temporary support of a five level basement excavation. Deep mixing was proposed by the excavation and shoring design-build team as the preferred method to construct infill panels between soldier piles because of the speed at which the shoring system could be constructed in variable fill, peat, wood waste and overburden compared with traditional secant piling methods. The development site is generally a truncated triangle in plan, with the longest side of the triangle being approximately 115.7 m (380 ft) long and the two shorter sides being approximately 71.6 m (235 ft) (Hybrid Shoring Wall 1) to 75.0 m (246 ft) (Hybrid Shoring Wall 2) long. The site is bounded by an existing bridge off-ramp structure along its longest side, and by city streets on the other two sides, as shown in Figure 1. The truncated section is approximately 16.8 m (55 ft) (Hybrid Shoring Wall 3) long. Due to project constraints, the hybrid DM and soldier pile shoring system was only proposed for the two shorter sides of the triangle and the truncated section. Traditional secant piles were installed for the longest side. This paper focusses on the hybrid shoring system. A typical detail showing the CSM infill panel with the soldier piles is presented in Figure 2."

Jan 1, 2017

By Janaka J. Kumara, Takashi Kurashina, Yoshiaki Kikuchi, Takahiro Yajima

"The inner frictional resistance of open-ended piles depend heavily on the degree of soil plugging. Many factors including pile diameter, relative density and end conditions of the piles influence the degree of soil plugging. In this paper, the effects of inner sleeves attached at the pile base on the inner frictional resistance are discussed. The experiments were conducted on a medium-dense sandy ground using smallscale model piles. The results suggest that the inner frictional resistance is influenced by sleeve height for 50 mm diameter piles although it is independent for 30 mm diameter piles. The results also indicate that soil plug height is influenced by the sleeve height. The results of the incremental filling ratio (IFR) showed that penetration of non-sleeved piles is closer to unplugged state than the sleeved piles. The results of the IFR also reveal that the degree of soil plugging is affected by the sleeve height for 50 mm diameter piles although the variation is very limited in 30 mm diameter piles. The results on the coefficient of lateral earth pressure suggested that it increases from 1.08 – 1.75 when the sleeve height is increased from 10 – 100 mm for 50 mm diameter piles.INTRODUCTIONPrevious studies have shown that the behaviour of open-ended piles is different from closed-ended piles (Szechy, 1961; Randolph et al., 1979; Paikowsky and Whitman, 1990). Open-ended driven piles are widely used for deep foundations, in particular in offshore deep foundations. Generally, it is accepted that a short open-ended pile produces a smaller bearing capacity than a similar closed-ended pile (Nauroy and Tirant, 1983). However, a long open-ended pile can produce a similar bearing capacity as a closed-ended pile due to a large inner frictional resistance mobilised between the inner pile shaft and inner soil (Lehane and Randolph, 2002). The ultimate bearing capacity of an open-ended pile, Qu consists of three components as given in Eq. 1."

Jan 1, 2017

By Daniel Stevenson, Richard Guenther

"The preservation of historic buildings is not only essential to the understanding of our national heritage, but it is also environmentally responsible to adapt existing buildings to compatible new uses. With this perspective, the American Enterprise Institute began exploring options to expand the newly acquired Andrew Mellon Building, located at 1785 Massachusetts Ave. NW in Washington, D.C., without causing any harm to the Beaux Arts style limestone façade and its plaster interiors. The building is a National Historical Landmark, but its 72,000 sq ft (6,690 sq m) of usable floor space did not meet the needs of its new owner. The building perimeter is very near the property line, so horizontal expansion was not possible. Adding height to the building was not an option, as this would have altered the historic nature of the building exterior. The only feasible option that could provide the desired floor space was to add a new floor underneath the existing structure. By adding a level beneath the existing building, an additional 28,000 sq ft (2,601 sq m) of floor space could be produced.Berkel & Company Contractors was chosen as the deep foundation/shoring contractor tasked with ensuring that the existing structure was stable and remained undamaged during the excavation and construction of the new lower level. To accomplish this, Berkel provided a shoring system that would act as both excavation support and permanent deep foundation elements for the final structure.Preservation of the existing limestone façade and plaster interiors was critical to the success of the project, as additional foundation settlements could damage these irreplaceable building components. Project specifications, therefore, included very stringent limits for foundation settlements. The maximum allowable total settlement for all existing building walls and columns was ¼ in (6 mm) for the duration of the project."

Jan 1, 2017

By Alessandro Bertero, Dylan Pearson, Wesley Schmutzler, Matteo Bertoni

"The SR 83/US 331 highway is located in the Florida panhandle, where it connects the Walton County beaches to the I-10 corridor. The roadway is of vital importance to the economy of the area as well as its safety since it represents the primary hurricane evacuation route from southern Walton County. The Florida Department of Transportation (FDOT) decided to increase the number of traffic lanes from two to four and improve the geotechnical properties of the moderately deep, very loose foundation soils, that had affected the highway rideability for years. The soil mixing was selected as the method to meet the unique deep ground improvement challenges of the project. The design required that Shallow Mixing Method (SMM) be used to build a 10-foot thick platform that transferred axial load to the bottom soil layers through a series of Deep Mixing Method (DMM) columns. Upon completion over 8,300 SMM columns and 1,500 DMM columns had been installed, with no remedial work required. Also, only 1% of the almost 1,500 specimens tested did not meet the specification requirements. This paper will describe the challenges encountered and provide valuable information that may be useful for other future projects, including details not previously published.INTRODUCTIONThe counties of Walton and Okaloosa have been a very popular vacation destination for many ears. The 50-mile long coastline boasts beautiful, sugar-white beaches and waters the color of emeralds. The popularity of the area has been growing even further, over the last few years. A consequence of this phenomenon is a fast-paced increase of the traffic flow on the SR83/US331 highway, especially at the bridge that connects the Walton County beaches across Choctawhatchee Bay (Fig. 1) to the heavily traveled I-10 corridor. The highway plays a very important role for the area also as a commercial link and as the primary hurricane evacuation route from southern Walton County. The increase in traffic has produced higher travel time, when not a complete traffic paralysis, and exacerbated the issue of ground settlement where accelerated wearing of road foundation occurred due to the presence of very loose, moderately deep, soils, that had afflicted the highway for several years. The Florida Department of Transportation (FDOT) decided to put an end to these issues by increasing the number of traffic lanes from two to four and improving the geotechnical properties of the foundation soils. The Design-Build Maximum Price Request for Proposal (RFP) issued for the expansion of the Choctawhatchee Bay Bridge saw the participation of numerous D/B teams which produced various technical solutions. Among them, the FDOT selected the Skanska/Parsons Brinckerhoff (General Contractor) proposal which provided for the use of soil mixing as the ground improvement technology. The design/build team assigned Foundation & Geotechnical Engineering (Designer of Record) the ground improvement design which Treviicos South (Specialty Contractor) would execute."

Jan 1, 2017

By Yeruva Ramanareddy, Sohail Wajid, Ahmed Shaz, K. Bhavani

"CP-06 is an NATM cross passage which connects up-line and down-line metro tunnels near Kilpauk Medical College, Chennai. It lies completely in loose silty sand to dense sand with water table almost touching the ground surface after Chennai floods. Pre-grouting was done before excavation to seal the area and to ensure no-loose pockets. The heading was excavated successfully but while benching excavation huge water ingress started seeping out. Sand also permeated along with water which became unstoppable due to cavity formation and caused the up-line tunnel to sink considerably. A large grouting exercise was carried out with different grout materials and techniques both from the ground surface and inside of tunnel to stop the water ingress and stabilize the tunnel. This paper describes the chronology of events that occurred in the tunnel during CP-06 issue. It elaborates all the different grouting techniques involved in the whole process of the tunnel stabilization. It includes a finite element analysis using Rocscience RS2 9.0 software showing the possible cause of sand incursion with water from the CP invert which lead to the tunnel settlement. This paper also describes the after effects and the lesson learnt from the whole incident.INTRODUCTIONConstruction of Metro Rails has become the latest alternative to cope up with the transportation demand of the growing urban cities population. L&T SUCG JV constructed Chennai Rail Metro Phase II Contract UAA-04 which included design and construction of approximately 4 km of route length of underground mass transit railway including 3 underground stations. This package also includes 12 cross passages which are NATM tunnels connecting upline and down-line side of TBM tunnel for safe evacuation of passengers in case of emergency. As per NFPA guidelines, this is a mandatory structure and there should be atleast one cross passage in 244m tunnel length.CP-06 is a cross passage connecting upline and downline tunnel between Pachiyappa College Station and KMC Station, in Chennai Metro. During the construction of CP-06, heavy water seepage of around 450 liters per minute was encountered during second round of benching excavation after full heading was excavated. An inflow of around 12-15 cum of sand and silt was also observed inside the tunnel along with the seepage water, which created piping inside the TBM tunnel causing it to settle continuously with time. A huge effort was made to stop the water ingress along with loose sand which was causing the running tunnel to settle, involving all possible grouting methods and temporary support installation."

Jan 1, 2017