Search Documents

By Peter Radziszewski

"Comminition process costs, which typically represent an important contribution to mining operating costs, can themselves be divided roughly between energy and liner /charge wear. As such, developing the ability of predicting mill wear will allow a more accurate estimation of wear costs and therefore their control. In this paper and based on the possibility of estimating energy dissipated in impact and abrasion by using a discrete element charge motion model for mill charge motion simulation, media wear will be investigated principally as a function of three wear mechanisms : impact, abrasion and corrosion. Experimental results will be used to identify a total media wear model. Model results will be compared with real mill data from three operating Australian mines. These preliminary results show for the cases tested that the overall average error, as compared with the observed cases, is 0 % with a standard deviation of 66.1 %. Results from the Bond abrasion index tests, for the same cases investigated, give an overall error of 73 % and a standard deviation of 192.5 %. Further work is in progress to improve test procedure, validity and confidence.INTRODUCTIONComminition process costs, which typically represent an important contribution to mining operating costs, can themselves be divided roughly between energy and line / charge wear. In Greenfield situations where the estimation of operating costs is critical in determining project feasibility, the level of confidence in such estimates becomes quite important. With regards to media wear, the Bond abrasion test currently serves as the standard media wear prediction device. However, as shown [l, 21 test results once compared with actual wear rates can vary greatly. Figure 1 shows test results as compared with 15 cases. Average error over this data is 73 % with a standard deviation of 192.5 %. As such, developing the ability of more accurately predicting mill wear will allow greater confidence in wear cost estimation and therefore their control."

Jan 1, 2001

By Graham Holmes, John Starkey

"The Kinross Kubaka Project is a gold mine located in the Russian Far East. The grinding circuit, comprised of a 6.1 m diameter x 2.74 m long SAG mill and a 4.1 m diameter x 5.5 m long secondary ball mill in closed circuit with cyclones, was built using SAG Power Index and Bond Ball Mill Work Index testing to determine the grinding energy requirements. Extremely cold climatic conditions and the need to keep heated space and capital costs to a minimum, dictated a grinding circuit with no in-circuit crusher and no conveyors external to the mill. High energy requirements for both the SAG mill and the ball mill were correctly predicted and have allowed grinding production tonnage forecasts to be met. Design test data and production results are given.INTRODUCTIONIn 1995 Davy International Canada, now Kvaerner Metals E & C, was commissioned as the Engineer and Project Manager for the Omolon Gold Mining Company, to design and construct a gold extraction plant for the Kubaka gold deposit, located in the Russian Far East. This deposit had been studied extensively in Russia during the exploration phase and a Feasibility Study was completed in 1993 by Kilborn who visited the site twice during that year to inspect facilities and to take metallurgical test samples. More samples were taken in 1995 to check ore hardness variability, as part of the final design program by Davy.The client’s objective in designing the Kubaka grinding circuit was to achieve design tonnage at all times, even when milling the hardest ore zones in the deposit. Since the samples taken in 1993 were taken as composite samples, it was necessary to take additional samples in 1995 to determine the extent of the variability. Six samples were sent to Canada for SAG Power Index (SPI) testing. Five of these were combined as a composite open pit sample, while the sixth sample was taken from the site adits as a composite sample to represent undergound ore. These two composite samples were tested to determine the MacPherson Autogenous Work Index for comparison with the SPI values."

Jan 1, 2001

By Peter C. Jones, Wanda M. Carter, David H. Watkinson

"Abstract - Pyrrhotite, chalcopyrite, and pentlandite are the dominant sulfide minerals in the 740 zone of the Kelly Lake orebody (Inco Ltd.), Copper Cliff Offset, Sudbury. Petrographic and quantitative electron microprobe analyses of minerals, from sulfide assemblages and host quartz diorite, of the 740 deposit have revealed three processes that have affected sulfide mineralization and associated sulfarsenide and platinum-group-mineral (PGM) distribution: magmatic, hydrothermal, and tectonic. Accessory, zoned cobaltite, and gersdorffite occur in sulfides as a result of these three processes, and PGM occur dominantly in hydrothermally remobilized and deformed ores. Where PGM are present in sulfarsenides they provided nuclei for sulfarsenide growth. Solitary PGM are orders of magnitude larger than those PGM found within sulfarsenide minerals. Five varieties of PGM occur, michenerite and sperrylite being the most common, with lesser froodite, hollingworthite, and ruarsite.The effect of a deformation is a localized fabric in the ore, revealed by pyrrhotite and chalcopyrite bands; pentlandite porphyroblasts also partially define the foliation. The deformed ore is also characterized by alteration of the adjacent quartz diorite, which produced an alteration assemblage including almandine garnet, Fe-rich biotite, and chlorite."

Jan 1, 2001

By Simon C. Dominy, Patrick R. Stephenson, Alwyn E. Annels

Abstract - The often complex, erratic, and localized nature of gold is a common feature of many vein-style gold deposits. This style of mineralization is often referred to as being nuggety or possessing a high-nugget effect. As a result of these complexities resource estimation is difficult and in general, only Exploration Results can be provided or an Inferred Mineral Resource estimated from surface drilling data alone. Underground development, further drilling, and probably bulk sampling will be required to delineate Indicated and Measured Resources. Tonnages can generally be estimated from diamond drill and development information with a reasonable degree of confidence. Grade is much more difficult to define with confidence because it is commonly highly erratic and discontinuous in nature. The dependency of higher confidence Resource categories on development information may create a Catch 22 situation, with funding for such development often depending on the prior definition of at least Indicated Resources. There are no easy solutions to these challenges posed by high-nugget effect deposits, and it is important when classifying and reporting not to downplay the uncertainties often associated with Mineral Resource and Ore Reserve estimates for such deposits. However, in common with all deposit types, if the principles that underpin the estimation, classification, and reporting procedures are borne in mind and common sense applied, most issues can be satisfactorily resolved. This paper discusses the classification and reporting of Mineral Resources for high-nugget effect gold vein deposits within the framework of the JORC Code (JORC, 1999).

Jan 1, 2001

By Simon C. Dominy, Ian M. Platten

"Abstract - Gold-bearing quartz reefs commonly show extremely erratic and unpredictable grade variation, although gross geological continuity may be good. This type of variation is often described as being nuggety or having a high nugget effect and can be measured quantitatively using the semivariogram. Understanding of geological features such as reef texture and structure will provide improved models for the interpretation of assay data, drill core descriptions, etc. In this paper, a case study from the quartz-hosted gold occurrences in the Gwynfynydd mine, United Kingdom, is described. The work provides a starting point for models of lateral variation and demonstrates the types of structural and textural features that may be sought to give clues to the prediction of gold distribution in similar deposits. Gold deposition at Gwynfynydd is primarily associated with the reef footwall. The host veins form a discrete group of structures that may have been emplaced early in the sequence of quartz veins forming the reef. This potentially exposes them to a maximum number of dissection events during repeat dilations of the lode. Gold was deposited in the local porosity at extreme concentrations, equivalent to kg/t grades, when the host fissure had become filled with a porous framework of crystalline quartz and sulfides. Distribution of porosity varied laterally along the vein as the result of the formation of clump-like growths of minerals from the vein walls. The growth style is relevant to the distribution of gold although it may not be relevant to the occurrence of gold in a particular vein. The preservation of pores with some connectivity late in the vein fill sequence may be important in permitting continued but slow fluid flows. This facilitates effective fluid reaction with wall rock-derived methane, thus changing the relative rates of gold and quartz deposition in favor of gold. The textural studies explain the first-order control of nugget distribution at Gwynfynydd but do not allow for prediction and optimization of the resource estimation process. This is principally because of the very low geological continuity and poor predictability of the high-grade pockets. Nonetheless, the work does provide a clear geological explanation for the erratic nature of the gold. It indicates textures and structures that can be used to determine geological continuity of the goldbearing elements within the gross reef envelope."

Jan 1, 2001

"RÉSUMÉOn discute les principales sources de dilution au cours d’une exploitation souterraine. Les différentes définitions de la dilution en usage sont analysées. Une nouvelle méthodologie de calcul simplifiée et facile à utiliser dans la pratique minière est présentée. Cette méthodologie permet de remplacer les différentes expressions analytiques en usage par les deux facteurs de dilution seulement : un «facteur de dilution planifiée» lié à la sélectivité d’abattage au niveau de la planification minière et un «facteur de dilution additionnelle » permettant de juger de l’efficacité du contrôle de terrain et de la dilution pendant l’exploitation souterraine. L’application de cette méthodologie donnerait un outil nécessaire aux niveaux de la planification, du suivi des travaux d’exploitation et d’éventuelles études comparatives des coûts entre les différentes situations minières.ABSTRACTThe principal sources of dilution during underground evaluation and mining are discussed, then definitions of ore dilution currently in use are analyzed. These definitions vary depending on the authors. A new ore dilution evaluation methodology is proposed, replacing the ten different analytical expressions by only two: the planned dilution factor related to the stoping selectivity, done at the mine planning level, and the additional dilution factor related to the efficiency of the dilution control measures during stoping operations. The conclusion shows that the use of this methodology would be a definitive asset in planning, in stoping operations follow-up, and in future costs comparison studies between mining operations."

Jan 1, 2001

By A. Paulin, J. Roth, S. Spaic

This experiment was carried out to see whether copper-iron ingots from Late Bronze Age hoards could have been produced by smelting ferruginous copper ores. Since ferruginous copper-ores are chalcopyritic, chalcopyritic concentrate from a present day copper mine was dead roasted in our experiment in lieu of a rich chalcopyritic ore. Charcoal was used as a reducing agent in the reduction of calcine (i.e., a product of dead-roasting), and quartz sand was used as a flux. Two separate metallic solutions, a copper-base and an iron-base alloy, were obtained as a result of two factors: the presence of carbon and the miscibility gap in the Cu-Fe-C system. The metallic melts appeared in a form of bigger or smaller droplets, enclosed by a molten slag which, during the cooling, solidified into metallic beads. The presence of both metals was noticed in the majority of the examined beads. It was therefore concluded that calcine consisted of an intimate mixture of oxides of both metals which were simultaneously reduced during the reduction process. Due to the miscibility gap in the Cu-Fe-C system, separate iron and copper regions were formed in the beads. In both regions, sulphide inclusions were found. The formed molten copper and molten iron solution were found to be saturated solutions. The metallographic analysis revealed the precipitation of iron out of copper and that of copper out of iron during the cooling and solidification of melts. The formed slag contained little iron and no copper oxide.

Jan 1, 2001

By Bernard Dallaire, Jean Cayouette, Sylvain Duchesne

"Louvicourt Mine's concentrator, located near Val d'Or, Quebec, treats an average of 4,300 tonnes of ore per day composed mainly of copper, zinc, gold and silver. An analysis of concentrator revenues and metallurgical losses shows a potential for additional gain, particularly in regards to precious metals (kustelite) where recovery is usually around 67 -70 %. The planning, installation and trial operational period of two Outokumpu SK-240 flash cells at the underflow of the primary cyclones took two years. The use of (( flash flotation )) technology has made it possible to exploit the favourable conditions at the underflow of the primary cyclones such as precious metal concentration and the presence of liberated coarse chalcopyrite. These conditions permit early flotation (fresh surfaces) of the kustelite and the liberated copper. Since the start-up of the flash cells, the metallurgical gains have turned out to be very positive with increases in metal recovery reflected in appreciable NSR gains. Also, significant savings in reagent consumption and a coarser copper concentrate have made it possible to reduce the drying cycle of the Larox filter presses since the cells were put into operation.BACKGROUNDLouvicourt Mine is operated by Aur Resources Inc. (30% ownership) on behalf of its partners Novicourt Inc. (45%, subsidiary of Noranda Inc.) and Teck Corp. (25%). The mine is located in northwestern Quebec about 600 km north of Montreal and about 25 km east of the mining town of Val d'Or. The mine commenced commercial production in July 1994.The massive sulphide ore deposit lies at depths varying between 450 m and 900 m. Mining reserves (2% Cu equi. cut-off) as of Jan. Is', 2000 are estimated at 7.5 million tonnes of ore averaging 3.4% Cu, 1.8% Zn, 28.0 g/t Ag and 0.9 g/t Au. Delineated ore reserves permit the use of a mechanized transverse blasthole mining method. The extraction order is a typical 1.3.5 mining sequence. Primary and secondary stopes are 15 m wide, 15 to 70 m long (25 m long average) and 30 m high. Backfilling for pillar recovery and regional stability is required."

Jan 1, 2001

By P. R. Jones

"The paper describes the CDN$400 million expansion at Hudson Bay Mining and Smelting Co., Limited’s operations. The company has continuously produced copper and zinc at the Flin Flon metallurgical plant since 1930. The paper details the company’s operational turnaround since 1995 and “The 777 Project” which includes two new mines, expansion and modification of the concentrators, expansion of the zinc pressure leach plant, a new zinc electrolytic cellhouse and modifications to the copper smelter gas handling system to reduce ground level gas emissions. IntroductionHudson Bay Mining and Smelting Co., Limited (HBMS) was incorporated in 1927 to mine and process the world-class Flin Flon copper and zinc orebody. Ore concentration and metallurgical facilities were constructed in Flin Flon. The metallurgical complex capability is currently 89 000 tonnes of copper metal and 98 000 tonnes of zinc metal from both HBMS and purchased concentrates.Flin Flon, with a population of 7000, is in Manitoba and partly in the province of Saskatchewan. The location is isolated with Winnipeg 800 km to the south and Saskatoon 500 km southwest.Today, three underground mines feed the Flin Flon concentrator, one feeds the Ruttan concentrator at Leaf Rapids, 200 km to the north of Flin Flon, and Chisel North mine feeds the Snow Lake concentrator (Fig. 1).The Flin Flon volcanic massive sulphide proximal and distal orebodies are within the Flin Flon greenstone belt which stretches from the west of Flin Flon to the east of Snow Lake, a distance of 250 km. The belt is approximately 100 km wide before disappearing below the paleozoic cover to the south."

Jan 1, 2001

By J. L. Jambor, M. J. Baker, M. J. Logsdon

"Abstract - Prior to the development of the Diavik Diamonds Project, baseline studies were conducted to determine the geochemical characteristics of four kimberlite orebodies as an aid in the design of both the water-management system and the facilities for containment of processed kimberlite and ore stockpiles. Materials tested included field samples of volcaniclastic and pyroclastic kimberlite, processed kimberlite (i.e., kimberlite ore which had been screened and washed as part of the processing procedure), and sedimentary mudstone (a minor xenolithic unit which was assimilated during kimberlite emplacement). Approximately 200 samples of kimberlite materials were collected as part of the geochemistry program. Test-work included whole-rock chemical analyses, acidbase accounting, kinetic leach tests using columns, and mineralogical analyses. Diavik kimberlite has major oxide and trace-element concentrations consistent with global averages for kimberlite. The mean total-sulfur content of the kimberlite material is 0.22 wt% S, but with a significant range. The kimberlite has an excess of carbonate minerals over sulfide minerals (average CO2 = 4 wt%, present mainly as calcite), and has a mean neutralization potential of 311 kg CaCO3 equivalent/tonne. A reactive form of framboidal pyrite associated specifically with the mudstone xenoliths is the primary source of sulfide-sulfur. Long-term kinetic tests confirmed the preliminary interpretations that were made from the static-test results. Kimberlite and processed kimberlite are net acid-consuming materials that produce alkaline drainages and have low but detectable leaching rates for SO4 and specific trace metals such as Al, Co, Cu, Ni, and Zn. If segregated from the kimberlite, mudstone xenoliths are acid-generating (pH = 3) and produce an effluent with elevated concentrations of SO4, Fe, Al, Cu, Ni, and Zn. The study demonstrates that xenolithic units in Diavik kimberlites have an important effect on the environmental geochemistry of the ore rock. The mineralogy and aqueous geochemistry of the kimberlite materials are such that they may not be suitable for general earthworks or as an alkaline agent and should report to an engineered facility to protect site water quality."

Jan 1, 2001

By Andre Vien, Jean-François Dupont

"Over the past several years, Svedala has developed a continuous charge monitor (CCM) for tumbling mills. It consists of a strain gauge embedded into a rubber lifter and associated electronics. This paper describes the installation and use of such a device on a SAG mill at the Holt-McDermott Mine. Comparison to measured static volumetric load and bearing pressure and inclusion of the measurement into a control strategy and its potential for condition monitoring is discussed. INTRODUCTIONWhile the measurement of load is very important in all kinds of grinding applications, the biggest benefits are expected from AG and SAG milling. This is what motivated Holt-McDermott to take a closer look at this problem, with a view to optimizing SAG mill performance.In many cases, the SAG mill control problem can be stated as maximizing throughput while avoiding a volumetric overload, with the other constraints (e.g. power, grind size, upstream/downstream equipment constraints, etc.) playing a less important role. This is certainly true at Holt-McDermott where the SAG mill is the production bottleneck about 90% of the time, and anything that can be done to increase SAG mill throughput will have a significant impact on operating profit.Although the goal of maximizing throughput while avoiding volumetric overload is simple to state, it has proven to be much more difficult to achieve. The mineral processing industry has expended a great deal of time and effort to devise control strategies in the pursuit of this objective. While much progress has been made, there is still room for considerable improvement. Across the industry it is probably fair to say that overloads occur relatively infrequently, but the real losses accrue as a result of the tendency to run rather conservatively."

Jan 1, 2001

By Mike Ounpuu

"Locked cycle testing has become more common practice in the last 10 years. Reasons vary from a desire to avoid pilot plant testing, demand for more variability testing within deposits, and perhaps most importantly, a request from the financial institutions who invariably finance many of the projects. Surprisingly, many people don’t understand locked cycle testing, analysis and balancing. This paper provides a brief overview of locked cycle testing, and then progresses into a more detailed discussion on the analysis and balancing of locked cycle test data. The paper endeavors to educate CMP personnel on how to determine if the test was good and if a reasonable metallurgical projection was made. The paper uses case studies to illustrate the key points.INTRODUCTIONA locked cycle test is a repetitive batch used to simulate a continuous circuit. The basic procedure has a complete batch test performed in the first cycle which is then followed by similar batch tests which have “intermediate” material from the previous cycle added to the appropriate location in the current cycle. These batch tests, or cycles, are continued in this iterative manner for an arbitrary number of cycles. The final products from each cycle, i.e. final concentrate and final tailings, are filtered and thus removed from further processing. At the end of the test, all the products, final and intermediate, are dried, weighed and subjected to chemical analysis. The test is balanced and a metallurgical projection is made.This description can be found in many of our classical textbooks for the mineral engineer 1, 2, 3,4. Unfortunately, none of these textbooks provide any discussion beyond the basic procedure. Often, they provide comments such as in Taggart’ where he states; “It is questionable whether in any case it approximates mill results any more closely than the standard batch test”. It is truly surprising that our classic textbooks promote that locked cycle tests are more art than science, and suggest that they can be of dubious value. None of the textbooks provide meaningful insight or discussion in how to assess:"

Jan 1, 2001

By Z. Xiao, A. R. Laplante

"The recovery of gold by gravity from grinding circuits differs from virtually all other gravity recovery approaches in that stage (or unit) recoveries are low, typically 1 to 5%, but overall recoveries are generally in the 25 to 60% range, because individual gold particles are presented many times to the primary recovery unit. Full-scale recovery is difficult to predict from benchscale tests. Further, maximizing metallurgical recovery is generally not the primary objective, because of the more efficient downstream recovery circuit (flotation or cyanidation). In this paper, a new concept, the gravity recovery effort, is presented to assist in the design and optimization of gold gravity circuits. It is defined as the product of the circulating load treated by the primary gravity unit, the recovery of this unit, and the gold room recovery. Predicted gold recovery is linked to the recovery effort, the size distribution of gravity recoverable gold (GRG), the dimensionless retention time in the mill and the partition curve of GRG. A case study of economic optimization of the gravity recovery effort is presented. INTRODUCTIONPredicting gold gravity recovery from grinding circuits has always been a hit-and-miss exercise. The problem can be traced to the highly variable gravity recoverable gold (GRG) content of ores, high GRG circulating load, fraction of the circulating load treated, and performance of primary gravity recovery and gold room. Typical values, highs and lows are shown in Table 1."

Jan 1, 2001

"The McArthur River uranium deposit is the single richest uranium ore body developed in the world to date. The ore body’s average grade is 15% U3O8. Proven reserves are in excess of 450 million pounds. The grinding circuit is located underground. The ground ore is pumped to a surface facility where the slurry is thickened and loaded into containers for shipping to the Key Lake mill 78 kilometers to the south.The paper will briefly describe the mining method employed. The underground ore handling and grinding circuit, and surface facilities including slurry load out, wastewater treatment and the freeze plant will be described in detail. The paper will emphasize radiation and safety procedures that are followed to minimize operator exposure to radiation risks.LOCATIONThe McArthur River mine is located 78 kilometres north of the Key Lake mill. It is located at latitude 57’ N in northern Saskatchewan, within the southern boundary of the Athabasca formation. The nearest town is Pinehouse, located 320 kilometres to the south. Access to the mine is by an all weather road and by a private airstrip.HISTORYThe McArthur River Operation is jointly owned by Cameco Corporation (69.805%) and Cogema Resources Inc. (30.195%). Exploration for uranium in the McArthur River area started in 1980 by the Saskatchewan Mining Development Corporation, a predecessor company of Cameco.In 1984, a 12-kilometre long basement conductor was identified at a depth exceeding 500 metres. Systematic exploration drilling of this conductor resulted in the discovery of the P2 North deposit. Subsequent surface drilling programs from 1989 to 1992 delineated a narrow ore zone over a strike length of 1700 meters at a depth of 500 to 600 metres. At this time, geological reserves for the deposit were estimated to be 2.4 million tonnes at a grade of 5.0% U3O8 for a uranium content of 260 million pounds U308"

Jan 1, 2001

By K. Prajapati, P. Hes

Transmission of vibration to the operator from percussive vibrating tools is increasingly of concern in industrial and mining applications. Prolonged exposure to high levels of vibration transmitted via the hand causes disorders known as hand-arm vibration syndrome (HAVS). The vascular component of HAVS is called vibration white finger (VWF) and has a debilitating effect on the hand. Vibration at frequencies below 1250 Hz, a tight hand-grip force and cold environments are reported to increase the likelihood of developing VWF. A vibration damping handle design with patents pending that addresses some of the causes of VWF has been developed and retrofits onto jackleg pneumatic rock drills. The handle is decoupled from the drill while maintaining jackleg twist-grip controls on the hand-grip using a combination of sealed self adjusting hydraulic pistons and compliant materials in series, and a new air control valve. The ergonomics of the hand-grip was also modified by the addition of a polyurethane sleeve with a diameter of 50 mm. The new hand-grip reduces direct cold metal contact and minimizes grip force. Measurement of vibration as the quantity acceleration was made in accordance with international standard ISO 5349. Overall vibration damping in all axes of 50% to 63% was attained at frequencies below 1250 Hz. The dimensions of the damping handle are comparable and its weight is only 100 g heavier than a standard handle.

Jan 1, 2001

By N. Wang, A. I. A. Salama

"An index to evaluate the amenability for processing of different coals is implemented. The index is based on the well-known Mayer-curve or M-curve. The index is superior to other existing indices and is implemented using Microsoft-Excel™. Several coals are used to demonstrate the implementation of the index proposed.IntroductionIn 1950, Mayer introduced a curve that carries the information embedded in the fir s t three curves or ash curves of the conventional washability tables and curves (Peng et al., 1979; Osborne, 1988). The curve was labeled the Mcurve (abbreviation for Mittlewertkurve in German or the Mayer- curve). The main idea behind the curve is to use the ordinate for the cumulative mass and the abscissa for the ash (attribute) mass. Specific slopes on the resulting curve represent the cumulative float, cumulative sink, and elementary ash (attribute) contents (Mayer, 1950, 1953, 1957; Venkatesan, 1975; Osborne, 1988; Salama, 1989). Beyond the ash values, the curve carries graphical information that can be used in evaluating coal processing characteristics. Consequently, it becomes possible to present several raw coals on a single diagram, thus making it easier to compare their processing characteristics. This is particularly useful in comparing various size ranges of raw coal or the same size range from different seams. Therefore, the M-curve is adopted as a vehicle for developing the “processing (washing) characteristics index” implemented in this paper."

Jan 1, 2001

By S. P. Singh

"The geological features of a rock mass have a direct influence on its blasting characteristics. It has been observed that perimeter control techniques provide excellent results in massive crystalline formations but may give poor results in weak and or highly jointed formations.A field study was conducted with the objective of understanding the role played by the geological features of a rock mass in producing and controlling blast damage. The field work involved the assessment of blast damage at several operating mines and the blasting of drift rounds in a geologically dominant rock mass.The effect of rock strength, rock quality designation (RQD), joint parameters and hydrogeological conditions on blast damage is described below. The influence of number and thickness of weak layers on blast damage is also discussed below on the basis of quantitative data. In addition, critical particle velocity ranges for damage to different rock types have also been outlined in this paper."

Jan 1, 2001

By Emmanuel John M. Carranza, Martin Hale

Abstract- An application of logistic regression to mapping of gold potential in the Baguio district of the Philippines is described. Categorical map data such as lithologic units and proximity classes of curvi-linear features, based on spatial association analyses, are quantified systematically and used as independent variables in logistic regression to predict the probability for presence or absence of gold mineralization. Regression experiments to compare between using all independent variables that are associated spatially with the response variable and using only statistically significant independent variables are performed. The results of the regression experiments are similar; however, the use of all independent variables produces slightly optimistic results but better prediction rates for the known gold deposits in the test district. At least 68% of the ‘model’ large-scale gold deposits and at least 76% of the ‘validation’ small-scale gold deposits were predicted correctly. The predicted geologically favorable zones are also similar to delineated geochemically anomalous zones. The technique presented using logistic regression as a data integration tool is effective for geologically constrained technique of mapping mineral potential.

Jan 1, 2001

By Michel Dagbert

"In their paper, Marcotte and Boucher (2001) cast some new light on the old problem of 2D estimation of vein-type deposits with thickness and grade of intercepts. Using a theoretical approach, some extensive simulation experiments and the Walker Lake data, they show that the direct approach (interpolation of grade at points on a regular grid) gives better estimates of the true grade at those points than the indirect approach (interpolation of grade x thickness or accumulation and interpolation of thickness) when there is some positive correlation between grade and thickness and that this better performance increases with the correlation of grade and thickness as well as the variability of both variables.We would like to bring some reservations to that conclusion by showing that even if direct point grade estimates are better than indirect ones, it is not necessarily true for block estimates and in particular for the estimated grade of the whole orebody itself."

Jan 1, 2001

By Karla Kaboth, Brad Garraway

"The surface of many concentrate thickeners has traditionally looked like that of a flotation cell. Over the last three years Normandy Golden Grove Concentrator, in partnership with Outokumpu Technology have developed and implemented an innovative breakthrough deaeration technology to address this problem.When installed in the thickener feedline, the system successfully detached air bubbles adhering to the solid particles and removed air bubbles from the feed stream, subsequently presenting a fully deaerated feed to the thickener feedwell.Tests to date have shown an 80% reduction in overflow solids. As a result, costs associated with concentrate loss and measures to recover concentrate that settles in process tanks and ponds have been minimized.MOTIVATIONIt is recognised in mineral processing operations that the entrainment of finely divided air in thickener feeds can cause significant problems in the operation of a thickener. This is particularly the case with thickening of flotation concentrates, in which air bubbles are strongly attached to the mineral particles and are difficult to remove. Such particles attached to fine air bubbles rise to the thickener surface, and hence over the weir and into the thickener overflow. High solids carryover can lead to a direct loss of mineral product, and if the product settles in process water tanks and ponds, the recovery of this product by means of intermittent dredging operations is usually expensive and inconvenient.Many concentrate thickeners are fitted with devices which attempt to alleviate this problem. Froth rings or baffles, skimmers and froth sprays, all play a part in reducing the amount of solids carried over into the overflow. However, many froths are very stable and persist despite these measures. In the worst cases, a thick froth layer forms which builds up to a depth greater than the froth ring, and hence may overflow or pass beneath the ring . Any concentrate that finds its way past the froth ring can also cause blockage of the overflow weir and launder, and has the potential to upset clarification performance by cutting off sections of the overflow handling system. The formation of a froth layer on the thickener also makes it more difficult for the operator to monitor the clarification performance."

Jan 1, 2001