Search Documents

By Z. Zhang

Aluminum boron carbide particulate reinforced composites have found new applications in nuclear industry due to their special capability to capture neutrons, Recently, Alcan successfully developed a liquid metal mixing process to fabricate Al¬B4C metal matrix composite instead of powder metallurgical technology. In the process, titanium is added into the composites to control interactions between boron carbide particulates and aluminum matrix, To understand the effects of titanium on the composites, the solidification microstructure of Al-16%B4C without or with titanium was examined by optical and electron microscopes. The results show that titanium can improve the uniformity of the particulate distribution within aluminum matrix if the titanium content in the composites is more than 0,5%, Furthermore, it is found that the layer with rich titanium on the surface of the particulates can limit the formation of AlB2 type compounds, which may greatly deteriorate the fluidity of the composites, In addition, it is also found that the amount of the reaction products in the composites increases with the increase of holding time. However, the rate of the increase is mitigated by the increase of the content of titanium in the composites. Besides, a procedure was proposed and implemented for the evaluation of uniformity of particulate distribution within aluminum matrix.

Jan 1, 2005

By Y. Qi

A cell-level nonlinear dynamic model of solid oxide fuel cell (SOFC) based on physical diffusion principles is built in this note. It demonstrates that reactant diffusion processes from gas flow bulks to triple phase boundaries (tpbs) play an important role in the dynamic behaviors of SOFC. The simulation shows that under certain condition, the effect of the double layer capacitance may be neglected. The phenomenon of slow rise of voltage in current interrupt experiment may be explained by the dynamic behaviors of partial pressures in the vicinity immediately above tpbs.

Jan 1, 2005

By A. Lam

The use of a liquid fed direct methanol fuel cell (DMFC) as a power source for micro and small portable applications is attractive due to its system simplicity, low temperature, etc. The aqueous methanol is directly oxidized and does not require additional fuel processing steps as in reformate based PEM fuel cells. In addition, the use of a liquid fuel is advantageous with respect to humidification, stack cooling and system energy density. The DMFC however, has technological issues that must be addressed before it can be widely adopted, particularly in larger applications such as small utility and transportation. At present, the crossover of methanol from the anode to the cathode is a major limitation on DMFC performance and fuel utilization efficiency. In this paper we discuss the influence of fuel modification on the control of crossover. This involves the use of different fuel additives and concentrations to minimize crossover. This appears to be the first reported case of the use of fuel modification (additives) to reduce methanol crossover. The rate of methanol permeation under passive conditions is discussed with respect to the different conditions.

Jan 1, 2005

By B. A. Peppley

The current most common method of hydrogen production for fuel cell systems, including SOFC systems, is autothermal reforming. Autothermal reformers have a number of advantages including fast start up and load following and ease of control. However, there are a number of problems inherent with the addition of air into a system connected to the anode feed such as dilution of the fuel with nitrogen and the potential for oxygen to reach the anode chamber directly. Pure steam reforming, which does not involve air addition, provides a richer fuel mixture to the SOFC anode and is inherently safer than autothermal reforming. Although in theory pure steam reforming can be shown to provide these advantages, a number of technical problems need to be overcome before such a system can be practical. In particular, issues such as catalyst degradation due to poisoning and thermal sintering, coking, as well as fuel-steam mixing need to be addressed. Experimental results from a prototype reformer will be presented to illustrate a number of these points. This paper will compare differences in system efficiency, safety and complexity between autothermal/SOFC systems versus a steam reformer/SOFC system. A system simulation will be utilized that is able to account for material and energy balances for a SOFC power generator operating on diesel fuel. The requirements for improved catalysts will be discussed and an analysis of the potential benefits of sulfur tolerance and lower temperature activity will be considered.

Jan 1, 2005

By E. Asselin

Electrochemical polarization experiments were conducted on alloy 625 in ammonia solution between 25 and 225°C and the results were compared with those of an oxygen solubility model. Results confirm that corrosion is under oxygen control, Normalized corrosion rates are determined based on the rate of oxygen diffusion to the corroding surface, and the corrosion rate at 200°C (-9.7 µA.cm-2) is roughly 24 times higher than the corrosion rate at 25°C (0.4 nA,cm-2), An oxygen-solubility model for Supercritical Water Oxidation (SCWO) conditions was generated using the Redlich¬Kwong-Soave (RKS) equation of state, Results of the model confirm many of the experimental observations from SCWO reactors which suggest that corrosion is at a maximum at temperatures just short of the critical point, The RKS/oxygen diffusion model predicts that the corrosion rate at 365° C is ?85 times higher than the corrosion rate at 25' C. Given that a normalized corrosion rate is obtained, this type of model could be useful for selection of SCWO reactor materials.

Jan 1, 2005

By AN. Kumar

Two fabrication stages in the manufacture of pipelines are identified as causing significant deterioration of the steel plates, namely cold bending and welding. The objectives of this work include quantitative assessment of the degradation of the quality of the steel plate by the loss of fracture toughness, and an estimation of the safe working pressure. The study was conducted on three API grade steels: X42, X46 and X60. After cold bending by the UO technique, various welding technique were employed for joining of the bend plates along the pipe length. A crack-tip opening displacement parameter (CTOD) was used at the onset of initiation and at the first load maxima as the criterion for assessing the toughness degradation under various fabrication stages and regime (such as WZ, HAZ and parent body). In addition, strength, hardness and impact energy values were determined to check the degree of degradation. Microstructural and microfractographic investigation of the fractured samples were also carried out in the scanning electron microscope (SEM). X60 grade steel plate suffers from CTOD toughness loss by around 38 and 55% after welding and cold bending, respectively, for the conditions studied. A combined effect of the two stages results in a loss in toughness by around 70% for the same steel. In X42 grade, the loss in impact energy ranges from 78 to 35 J due to electrical-resistance welding study (ERW). Crack resistance curves are also obtained for the steels to study the crack growth resistance behaviour and to supplement the information on crack initiation behaviour. The orientation of the pearlite banding, as observed on the fracture plane with respect to notch front and applied loading direction appears to have a strong influence on the microvoid-coalescence mechanism of fracture as well as the toughness values. An integrated analysis of the performance of pipelines, considering all these key factors, is discussed.

Jan 1, 2005

By R. Krentz, P. D. Cordingley

The nickel-cobalt sulphides produced from limonitic laterite ores by Moa Nickel S.A. in Cuba are refined at the Corefco nickel-cobalt refinery in Canada. Major changes to the refining process were required when the Moa sulphide feed, with its unusually high cobalt content, was introduced in the early 1990's. In the period 1994 to 2005 the production capacity of the refinery has increased dramatically to match increases at Moa, and significant process improvements incorporated. The process flowsheet consists of the original ammonia leach process, optimized for cobalt chemistry and overall leaching capacity. Extraction of metal values is followed by the unique nickel-cobalt separation technology, in which most of the cobalt is separated from the ammoniacal nickel sulphate leach solution by precipitation as a nickel-cobalt hexammine salt. This salt is refined from a Co:Ni ratio of 1:1 to over 10,000:1 by selectively leaching nickel, redissolution and recrystallization in ammonium sulphate solution. Nickel and cobalt are recovered using the well-known Sherritt hydrogen reduction technology. This paper reviews the chemistry described above, examines some of the changes in operating conditions made over the years and highlights some of the recent physical changes made to the refinery.

Jan 1, 2005

Strips of AA6111 automotive alloy were cast on a horizontal single belt strip casting simulator, Pure copper and carbon steels substrates plasma sprayed with different coatings for improving the strip surface quality, were used as chill moulds, Experimental studies revealed that a graphite coating provided the greatest benefit in achieving good surface quality. The interfacial heat fluxes during solidification of AA6111 strip were calculated by the IHCP method (Inverse Heat Conduction Problem). Temperature variations and cooling rates within the strips were then calculated through numerical simulations based on the time-dependent heat fluxes obtained by IHCP, The effects of casting parameters, including casting temperature and strip thickness, on interfacial heat fluxes, cooling rates and microstructures, were investigated, Although the maximum interfacial heat fluxes on the chill copper substrate were much higher than the results obtained from the steel substrates, the solidification times of the melts were mainly determined by strip thickness. Very fine equi-axed grains were obtained for both 1.2mm and 2.5mm thick strips thanks to the rapid extraction of heat, and effective grain refinement.

Jan 1, 2005

By W. Basuki, B. Setyotomo, L. Hakim, R. Hendrajaya

Due to high crack sensitivity of slab product of gas and oil line pipe application, its steel making process and alloy composition were evaluated and then improved to overcome its critical solidification process and reduced surface defects. The study was conducted at Slab Steel Plant Krakatau Steel. The purpose was to improve slab surface quality by reducing surface defects so that the slab surface doesn't need to be totally repaired. The method applied was by performing plant trial process, which the secondary process parameters such as alloying method and the casting parameters such as casting powder selection, metallurgical cooling, mould level control, and superheat were continuously monitored and then adjusted to the surface quality of the product. Based on the calculation of Ferrite potential of the steel, the chemical composition was designed to achieve optimum casting parameters in order to avoid high shrinkage during solidification. The results of the study are decreased surface defect quantity, and smooth casting process. The quantity of crack decreased by almost 90%. The slab surface repairing was significantly reduced from 85. % to less than 10%. These new casting parameters and developed alloy composition are then used and standardized for the mass production of the steel.

Jan 1, 2005

By G. T. Lapidus, R. M. Luna-Sánchez

In the present study, a series of cyanidation experiments were performed on a bulk sulfide concentrate which contained silver in four distinct phases, to determine its extraction rate, varying the oxygen concentration. The results showed that three of the four phases were refractory, aguilarite (Ag,iSeS) being the only leachable phase, and that the effect of the oxidant concentration is minimal. Mathematical simulations were performed, adjusting only the Damkohler number to adequately fit the experimental data. This model, and the mechanism implied, was compared with that found for acanthite (Ag2S) in a previous study, and the differences between the two discussed.

Jan 1, 2005

By R. L. Eadie, J. L. Luo

The effect of plastic deformation on near-neutral pH stress corrosion cracking (SCC) also known as environmentally assisted cracking was studied by cracking rate measurements. All the tests were conducted in a synthetic near-neutral pH solution. The traditional potential drop tests using compact toughness (C-T) specimens with 2-3 mm long pre-cracks showed varying plastic deformation by rolling would increase the material's susceptibility to SCC. This was confirmed by cyclic loading tests using double notched flat tensile specimens with 200-300 µm long pre-cracks which gave the same results that the specimen with large scale plastic deformation by tensile loading had a relatively faster crack growth rate than that with only small scale plastic deformation.

Jan 1, 2005

By A. Bamber

Canadian leadership in a global mining context will depend not only on entrepreneurship and best practice but also on technological innovation. This paper argues for more ambition and commitment to R&D for technological innovation in Canadian mining. It focuses on underground hardrock mining, where past R&D initiatives have simply not stood the test of time, and it is important to examine why. Concerns arise because industry’s commitment to R&D has not been sustained over time. Innovation through exploration, processing, and environmental technologies has been more significant. Meanwhile, R&D capacity and synergies in government institutions and universities have not been exploited. There is a need for more commitment, coordination, and collaboration by industry, governments, and universities. This paper examines some corporate models that have achieved sustainable innovation, along with some that have not. A strategy for innovation is discussed that relates to culture, commitment, coordination, and collaboration.

Jan 1, 2005

By J. Fournier

A novel sol ? gel (SG) synthesis procedure utilizing varying ratios of glycine and ethylene glycol to total metal cations has been developed to create high purity nanometer sized La0.65Sr3.5MnO3 powders. X-ray powder diffraction (XRD), transmission and scanning electron microscopy (TEM, SEM), and dynamic light scattering (DLS) have confirmed that the crystallite sizes of such powders are ~ 20 nm, and the aggregate particle sizes vary between 100 to 300 nm. Mixing varying weight percents of SG LSM powders with commercially available Praxair LSM in a composite LSM/YSZ functionally graded cathode has been shown, through the use of electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV), to exhibit enhanced oxygen reduction kinetics vs. at conventional cathode materials.

Jan 1, 2005

By D. Embury

The construction and utilization of oil and gas pipelines is a vital aspect of the Canadian economy. The evolution of materials for this application can be considered as part of an evolutionary process in which the processing of the materials is linked to the design requirements of the pipeline. The evolution of both materials and designs will be considered in terms of parameters such as yield strength, work hardening characteristics including strain path changes such as the Bauschinger Effect and toughness. The final portion of the presentation will consider the possible uses of non-metallic materials, composites and 'smart 'systems in pipeline construction.

Jan 1, 2005

By J. Lu, D. G. Ivey, H. Henein

Microalloyed steels are widely used in the oil and gas industry. They are a class of high strength, low carbon steels containing small additions of niobium (Nb), titanium (Ti), molybdenum (Mo) and/or vanadium (V). These steels have good strength, toughness and excellent weldability, which are attributed in part to the presence of nano-sized carbides, nitrides and carbonitrides. In the pursuit of developing higher strength microalloyed steels, it is of great interest to quantify the size, distribution, volume fraction and chemical speciation of these precipitates. However, characterization techniques suitable for quantifying fine precipitates are limited. Possible characterization techniques include SEM, TEM and matrix dissolution. A comparison is presented of the various techniques.

Jan 1, 2005

By L. Sun

Recently, micro-tubular solid oxide fuel cells (SOFCs) have attracted the attention of many researchers because of their numerous advantages over larger tubular and planar SOFCs. These include excellent thermal shock properties giving rapid startup/shutdown capability, a high volumetric power density compared to larger tubular SOFCs, and reduced sealing problem compared to planar SOFCs. In order to screen cathode materials for micro-tubular SOFCs, the perovskite cathodes were deposited, using a variety of methods, on 10.5 mol % yttria-stabilized zirconia (YSZ) tubes. Their electrochemical properties were then evaluated by using electrochemical impedance spectroscopy and steady-state polarization methods, based on a three electrode configuration, and with the reference electrode position carefully optimized. The oxygen reduction reaction kinetics at the cathode/electrolyte half cell were then investigated in detail.

Jan 1, 2005

The negative effects of pyrite and pyrrhotite on thiosulfate gold leaching have been investigated. Possible remedies to reduce some problems are discussed. In a gold bearing pure silicate ore, 92% of gold could be extracted within 3 hours using a solution containing 0.2 mol/L ammonium thiosulfate, 0.9 mol/L ammonia, 30 - 300 ppm copper sulfate and 8.6 ppm dissolved oxygen at pH 10.26. The thiosulfate consumption was 7.1 kg/t under these conditions and could be further reduced to 3.5 kg/t by decreasing the dissolved oxygen to 0.3 ppm. Addition of 16% pyrrhotite or pyrite into the silicate slurry led to a decrease in gold extraction by 2% or 9% respectively and an increase of thiosulfate consumption by 11 kg/t or12.8 kg/t respectively in three hours. Several adjustments, such as increasing copper ion and ammonia concentration and reducing the dissolved oxygen level to 0.3 ppm resulted in increased gold extraction and lower thiosulfate consumption despite the presence of these sulfides.

Jan 1, 2005

By D. Bai, F. Hamad, S. Abraham

For the integrity of welded structures such as pipelines, the toughness of the heat-affected zones (HAZ) is an important property. This property is often specified in terms of Charpy V-notch (CVN) impact toughness and determined by the standard test method. An experimental study has been conducted in an industrial laboratory to measure the impact toughness of the coarse grain heat-affected zones (CGHAZ) of an X80 line pipe material. The field girth welding conditions in terms of heat input were simulated, together with special edge preparation to improve the targeted testing of the CGHAZ. The effect of toughness of the neighboring regions, in particular the weld metal, on measured impact toughness of the CGHAZ was investigated. The fracture paths of the CVN tested samples were examined by both optical and scanning electron microscopy. The deviation of segments of the fracture path into the weld metal was found to have a significant effect on the measured impact toughness of the CGHAZ.

Jan 1, 2005

By M. D. Vance, G. R. Corbett, S. D. Butt

Surface wave imaging is a relatively new seismic technique that generates subsurface depth images without having to drill boreholes into the ground, and is rapidly becoming a standard tool in non-destructive geotechnical characterization. This paper presents a case study of the application of these surface wave techniques to image shallow abandoned mine workings at the Montague Gold Mines district near Dartmouth, Nova Scotia. This district has numerous steeply dipping narrow vein workings from historical mining activity, and has actively subsiding and collapsing crown pillars. Due to the rugged conditions at the site and the relative narrowness of the openings (often less than 1 m), a surface seismic system was developed that had improved portability and lateral resolution over other available seismic imaging systems. Seismic surveys were conducted over two sites where independent evidence indicated the presence of shallow mine workings. At one site, a comparative gravity survey was also conducted. The seismic data was processed to generate velocity vs depth images. Overall, the velocity images show vertical zones of zero velocity in the same lateral positions where historical mapping, current subsidence and gravity surveys indicate the presence of steeply dipping workings. Further, the velocity sections are consistent with the thickness of the till cover at each site and the possible weakening of crown pillars at one of the sites.

Jan 1, 2005

By P. Abachi

Cemented carbides or hard metals that generally consist of hard tungsten carbide and a tough metal binder such as cobalt are important in many segments of the world economy, ranging from automobile related components to machining, cutting, and drilling tools. For metal cutting operations such as turning and milling, replaceable cemented carbide inserts are frequently used. The exposure of inserts to very severe conditions (e.g. temperatures as high as 1000°C) in combination with very high loads, limits their lifetime. When the tools and components are scrapped, they are collected with a view to recovering the tungsten carbide and cobalt due to both their environmental aspects and their strategic importance. In this work, a selective electrolysis process was used for recovery of WC powder particles from cemented carbide scraps. The WC-10Co and WC-10Co-VC up to 3 wt.% VC was produced using powder metallurgy route. The mean particle size of WC, Co and VC were selected as 2.5, l.5 and 2.2 µm respectively. Referring to electrochemical curves of WC-10Co cemented carbides in hydrochloric acid solutions with different concentrations, the recovery rate was enhanced in IN acid. Therefore, this solution was selected for recycling of all samples. The surfaces of as-produced and corroded specimens were investigated using a scanning electron microscopy (SEM). Detection of corrosion products was provided by energy dispersive spectrometry (EDS). According to results, the selective electrolysis process could be useful in the recycling of scrap carbide materials, although more studies should be undertaken on economical aspects of the process and the quality of samples produced using recovered powders.

Jan 1, 2005