Search Documents

"Air Products approached LAC Minerals in 1987 to initiate trials with pure oxygen in the leach circuit at several LAC facilities in Canada. This paper gives an overview of oxygen use and covers specific operating data from the Doyon and Terrains Aurifères mills near Val D'Or in northwestern Quebec. LAC also uses oxygen at the Macassa mill in Kirkland Lake, Ontario.In addition to the LAC facilities, oxygen is currently in use for test purposes at the Holt McDermott mine in Kirkland Lake, Ontario and the Camflo mine near Val D'Or.There are two requirements for oxygen in the cyanide leach mill. Firstly, oxygen is required in the familiar gold dissolution reaction as follows:(1) 4 AU (s) + 8 NaCN (aq) + 02 (aq)+ 2H 20(aq) - 4NaAu(CN) 2(aq)+ 4Na OH(aq)Of the reagents on the left side of the equation, the availability of gold is fixed by the ore in question. Obviously, water is available in excess, 1eaving cyanide and oxygen as the limiting constituents in the process. Most mills operate with an excess of cyanide, which is fairly closely monitored. Dissolved oxygen levels, however, are not normally watched very closely and find their own level based on the temperature, the availability of compressed air and the ability of the ore to consume oxygen.Typical D.O. levels are in the 3-8 ppm range, however levels less than 1 ppm are not uncommon for refractory ores.With pure oxygen, dissolved oxygen levels as high as 30 ppm can be achieved. (Figure #1). This greatly accelerates the kinetics of the leach reaction and may also shift the reaction further towards completion thus increasing gold dissolution slightly."

Jan 1, 1990

Thermal barrier coating (TBC) systems provide thermal insulation to high temperature for aero¬propulsion. A fracture mechanical model developed earlier for multilayer systems is applied on TBC to realize superior performance by enhancement of fracture resistance. Functionally gradient materials (FGM) solution concept is the basis of approach followed here. A few realistic FGM TBCs are considered in the analysis in addition to a conventional TBC as the base case and a hypothetical worst case with YSZ-YSZ interface. Parameters like number, composition and thickness of graded layers and elastic modulus are considered for the analysis and quantitative improvement of fracture resistance of TBCs. The analysis is confined to deep crack with crack size to width ratio as 0.5.

Jan 1, 2010

By M. Bigdeli Karimi

In this study, the effect of strain level and holding time in semisolid temperature range via SIMA process on AS21 Mg alloy was investigated. Some cylindrical samples of this alloy with 1cm in height and 2.5cm in diameter (H/D=0.4) were compressed to 10%, 20%, 30% and 40% at 300-C. Then, the samples were reheated in semisolid temperature range at 614°C for various times. The results of optical microscopy and image analysis showed that with increasing of strain and holding time, dendritic structure changed to equi-axed structure, gradually. Also, the best conditions to obtain good globular structure were achieved. Furthermore, it was seen that after compression and reheating, Mg2Si intermetallics with Chinese script morphology converted to dispersed-fine particles which were distributed into the ci-Mg grains.

Jan 1, 2007

By H. Helmstaedt, P. Thurston, R. Harrap

"Evolution of the continental lithosphere over Earth’s 4.6 billion year history is one of the fundamental questions of geoscience. Much of the Earth’s present-day continental crust formed during the first 2 billion years, the Archean eon, of the planet’s lifetime and thus, Archean processes of lithospheric formation must be studied in order to address this question. Until recently, the processes of Archean lithospheric evolution were thought to be fundamentally different from present-day plate tectonic processes. However, subsequent evidence suggests that the growth of Archean continents may be explained in terms of modern tectonic accretionary tectonics similar to those presently operating in the southwest Pacific region. The evidence supporting this hypothesis was compiled largely by Canadian geoscientists working in the Superior Province of the Canadian Shield in northwestern Ontario, over the past 15 years. Study of Archean rocks is also economically important because the Archean rocks of the world, although comprising only a relatively small fraction of the exposed continental crust, contain much of the world’s mineral wealth, including more than half of the world’s gold, as well as significant base metal reserves. Furthermore, the vast majority of primary economic diamond deposits are derived from the lithospheric roots beneath Archean cratons.The LITHOPROBE Western Superior Transect is located within the western part of the Superior Province in northwestern Ontario (Fig. 1). The Superior Province is the largest and best exposed Archean crustal block in the world and forms the nucleus of the North American continent. The internal structure of the Superior Province records a history of the processes that formed the earliest lithospheric elements of the Earth into cratons, thus providing an ideal laboratory for investigating early crustal evolution. The Western Superior Province is characterized by a regional pattern of alternating, 100 km to 200 km wide geological belts (Fig. 2). The observed geologic relationships between and within these subprovinces have been explained in terms of a modern tectonic model of terrane accretion. Oceanic floor, volcanic island arcs, oceanic sediments and continental fragments were accreted successively from north to south against the southern margin of a cratonic nucleus (North Caribou terrane, Fig. 2) which grew steadily in size with the arrival of new terranes through geologic time. If this model is correct, it suggests that the tectonic processes operating today have been active without major variation over the past 3 billion years."

Jan 1, 1998

By G. A. Kosick, G. S. Dobby

"This paper presents the principles and application of a recently developed control system for flotation columns and column circuits. The control system uses triple pressure sensors to directly sense zone densities and level, and to help in characterizing the operating behaviour of individual columns. A complete expert system development tool is incorporated within the system to provide the facility for full operator training, an on-line help facility, and a means for incorporating the column behavioural patterns into decision making rules. The system is configurable to any number of columns and can be run in either supervisory mode or direct control through Minnovex PIO software. Additional process signals can be interfaced with the system if desired. Operating experience with the control system on the Minnovex column flotation pilot plant is described.I: INTRODUCTIONColumn flotation cells have been more difficult to control and are more sensitive to circuit changes than conventional mechanical flotation cells. This susceptibility encouraged investigation into various types of control strategies ranging from inexpensive single pressure measurements for level control, to highly instrumented and expensive systems using a variety of control methods.Flotation operators, in many cases, do not understand the column control philosophy or have not been trained to deal with this new type of cell. Some operators have subsequently absolved themselves of the column operating responsibility. Some column cells, for example, have run for hours with slurry pouring over the top or no froth coming off at all.ColumnEX is a column flotation control system which was developed from the viewpoint of an operating shift foreman who wishes to:1. control the column or column circuit through a genuine understanding of what is happening inside the columns, and2. to share this knowledge with his flotation operators and be available to guide them through times of circuit upsets."

Jan 1, 1990

By P. M. Hedley

GOLD mining in Nova Scotia, as in any other gold district, has its own peculiar problems. Being in close proximity to excellent roads and to railways, and being blessed with good labour, the majority of gold mines in the Province find their paramount trouble is geological, namely, ore finding. After six years of continuous mining at Goldenville, the staff of Guysborough Mines, Limited, has collected many facts, has come to some definite conclusions, and has made a lot of guesses, some good and some bad. It is the purpose of this paper to set down such information as we have been able to gain in the hope that it may prove useful to other operators, present and future, faced with similar problems. What may be true of one Nova Scotian mine will not necessarily be true of another, so that the observations that follow should be considered as primarily applicable to Goldenville. Stated facts, conclusions, and theories are the result of the combined thought and effort of Head Office officials, of members of the Provincial and Federal Departments of Mines, and of members of the mine staff, past and present. Grateful acknowledgment is made to all.

Jan 1, 1941

By O. A. Ojo, D. L. Chen, N. Zhou, J. Q. Zhang, A. K. Khan

Dual phase (DP) steels are designed to consist of hard martensite dispersed in a relatively soft ferrite matrix, which offers a favorable combination of high strength with good deformability. Fiber laser welding (FLW) is becoming increasingly important for joining advanced materials due to its flexibility and deep penetration. In this study, the microstructure of a dual phase steel, DP980, welded by FLW technique was carefully analysed. Gleeble thermo-mechanical simulation coupled with analytical transmission electron microscopy (TEM) revealed that the FLW process produced significant microstructural changes in a narrow heat affected zone (HAZ) and fusion zone (FZ), which can result in dramatic changes in mechanical properties. This is reflected in the micro-hardness profile obtained across the welded material. The salient phase transitions induced by the FLW, including the formation of new martensite grains in the upper-critical HAZ and FZ, are discussed.

Jan 1, 2014

By K. C. Corin, Z. G. Song, J. G. Wiese

In the present investigation flotation was used as a diagnostic to understand the effects of changes to the media during the grinding stage. The observations from flotation for different media are discussed in terms of particle size distribution, water recovery, solid recovery and valuable mineral recovery. The chemical parameters; pH, redox potential (Eh) and dissolved oxygen (DO) levels were measured. A Base Metal Sulphide (BMS) ore was ground under media of different shapes and compositions to determine the effect of different rod/ball material on the flotation performance of the ore. For a given grind (D80 = 75 µm), media shape had no effect on flotation performance of a BMS ore. Different grinding media had significant effect on slurry chemical properties and flotation performance. Mild steel rods (RMMS) produced the highest solids recovery, nickel and pyrrhotite (Po) recovery, with the highest ethylenediaminetetraacetic acid (EDTA) extractable iron and the lowest DO level. Chrome steel balls and stainless steel rods produced the lowest metal recovery, EDTA extractable iron and the highest DO level. A complementary study was conducted to investigate the effect of using different grinding media compositions, viz, ceramic, forged steel, 15% chrome steel, stainless steel and a mixture of stainless steel and 15% chrome steel (50:50) balls were investigated using a Platinum Group Mineral (PGM), UG2 ore. Grinding products of five different media produced the same solids and water recovery, but the grades and recoveries of Platinum Group Elements (PGE) and chromite were different. Grinding products of ceramic media showed the best flotation performance, with the highest PGE recovery and the lowest Cr2O3 recovery. While grinding products of stainless steel balls (SS) produced the lowest PGE recovery and highest Cr2O3 grade and recovery in the concentrates.

Jan 1, 2016

By Paul MacLean

MAC TSM ?Mining and Biodiversity Conservation 1.Corporate biodiversity conservation policy, accountability and communications 2.Facility-Level biodiversity conservation planning and implementation 3.Biodiversity conservation reporting ?Activities indicative of level AA -AAA (formerly 4-5) performance: ?Independent verification ?Integration into broader business strategy and planning processes ?Engagement with communities of interest ?Commitment to actively partner with other organisations for biodiversity conservation

May 1, 2011

By T. L. McCall

CHANGES in mining practices have evolved so quietly and unobtrusively that perhaps we scarcely appreciate how truly startling these changes are unless we cast our minds back so as to compare the past with the present. Such retrospection is, indeed, necessary when attempting to forecast the future, for it is only by carefully reviewing the past that we can hope to obtain an indication of what the future may hold in store. In this instance, it is not necessary to delve into the very early history of . coal mining, as our purpose will be served if the last three or four decades are reviewed, a period that is still fresh within the memory of many of us. These earlier days might be termed the selective period of mining, for at that time the coal resources of the world had not been tapped to anything like the extent they are at present and this condition enabled the owners and operators to exercise selective powers and only mine such seams of coal as could be most easily reached an worked at the lowest possible cost and which, at the same time, would suit the requirements of the market. Carrying this thought of selective mining still further, the miner, who was then an artisan skilled in all the branches of his calling, was able to select or discard such parts of the seam he was working that the co al sent out of the mine was acceptable to the consumer with just the barest minimum of preparation. Compare these conditions with the? conditions prevailing today, when coal seams of medium height, good quality, and readily accessible have been largely depleted and the operator has been compelled either to carry on his operations under much greater depths of cover where the coal is more costly to win, or else to work seams of lesser height or of poorer quality.

Jan 1, 1938

By A. Alfantazi, E. Asselin

"The corrosion of commercially pure titanium (CP-Ti) was studied from room temperature up to medium temperature (~160°C) under conditions relevant to medium temperature chalcopyrite leaching processes. The corrosion rates were measured by immersion and electrochemical tests in sulfuric acid. The influences of chloride, cupric and ferric ions on the corrosion rate and behavior were also investigated. Corrosion of the CP-Ti did not account for the total current density measured by linear polarization tests. The corrosion rates of CP-Ti under medium temperature leaching conditions were surprisingly high. The corrosion rate measured in ferric containing solution at 160°C was approximately 20 mm/yr.INTRODUCTIONTitanium exhibits excellent corrosion resistance in many aggressive environments because of the formation of a very chemically stable, highly adherent, and protective oxide film on its surface (Mitsuo et al., 2002). Because titanium is the only metal available at a reasonable cost that resists the high temperature corrosive slurries in many leaching processes, it is often chosen as autoclave liner material where it is subjected to severe conditions of acidity, temperature and pressure (Grauman and Say, 2000).A number of distinctly different hydrometallurgical processes for the pressure leaching of chalcopyrite have been developed and patented by various companies and they can be classified into low, medium and high temperature regimes (McDonald and Muir, 2007). For example, chalcopyrite concentrate may be processed at medium temperatures (115-175°C) and pressures of 800-2200 kPa (Dreisinger, D., 2006; Sahu and Asselin, 2011). The lixiviant may contain 20 to 55 g/L sulfuric acid, 8 to 12 g/L chloride ions, 10-25 g/L Cu2+ (Jones, 1995, 1997, 1999), and less than 1 g/L Fe3+ (Defreyne et al., 2005). The amount of these additions is determined by the grade of the ores and details are shown in Table 1."

Jan 1, 2012

By P. M. Tyroler, W. J. Thoburn, M. R. Alberty

"An initial test of this unique application demonstrated that hot gunned refractory would adhere satisfactorily. Subsequently, it was found that the proportion of material sticking during application increased with increased vessel temperature and when a mix containing pitch was used. About 75 per cent of the latter type adhered when it was applied at 1600°C.TBRC availability increased from an historical average of 62.5 per cent to 64.7 per cent during four campaigns when hot gunning was routinely practiced. Refractory cost was about 20 per cent less than that anticipated without gunning. Average parameters per campaign with gunning ranged as follows: 90 to 108 heats, 10 to 37 applications and 1.4 to 2. 7 hours per application. Prior to gunning, the average number of heats per campaign was 73.IntroductionThe Top Blown Rotary Converter process at Inco's Copper Cliff Nickel Refinery converts copper-nickel-sulphur concentrates to a material suitable for carbonyl refining (1),(2).Operating conditions are particularly hard on refractory. Batch cycles finish at temperatures up to 1650°C, with occasional excursions over 1700°C. New heats are then usually initiated immediately and the refractory is subjected to intense thermal shock from the cold feed. Temperature cycles are also introduced three to four times during a heat when the process is interrupted for scrap charging, temperature measurement or sampling.Abrasion wear results from rotation of the converters at speeds up to 15 RPM and from agitation of the bath with supersonic-velocity oxygen. Mechanical damage also occurs when chunks of scrap or solid matte are processed. Chemical corrosion is also present, as we know from our own laboratory work(2) and reports of operations elsewhere. As a consequence, refractory material and installation form a very large proportion of the converter plant costs. Equally important is the loss of converter availability during rebricking; this significantly reduces plant capacity."

Jan 1, 1981

By Chas Kemsley

NO. 6 shaft at Dome Mines, Limited, is an internal shaft going down vertically from the sixteenth, or 2,000-ft., level to the twenty-ninth, or 4,000-ft., level, with loading station and sump below this. It is located approximately 4,600 feet east of No. 3 shaft, the latter being Dome's main shaft through which ail ore, men, and material are handled. The decision to sink this shaft was made in May, 1935, and work was commenced almost immediately. To reach the site of the new shaft, 3,100 feet of cross-cutting, and 1,400 feet of slashing to widen existing cross-cuts, was necessary. On account of the long haul and the large amount of material to be handled, trolley haulage was decided upon and installed as soon as possible to facilitate the removal of waste rock from the crosscut and other necessary excavations. Figure 1 shows a cross-section of the cross cut and the manner in which the trolley wire is supported and guarded. For hanging each individual cross-piece, two holes are drilled into the roof and filled with snug-fitting wooden plugs. Into these, %-in. ragged hanger bolts arc driven by means of a stoper. The bolts are of various lengths to allow for irregularities in the face of the rock, and they have sufficient thread to permit several inches of adjustment for proper alignment of the cross-pieces. These hangers are spaced at 8-ft. intervals except at the curves, where 5-ft. spacing is used. A 2 in. by 6 in. cedar plank is fastened to the cross-pieces directly over the centre of the track. To this the trolley-wire supports are bolted, and 1 in. by 10 in. cedar boards are nailed on each side to act as guards. Two power-supply cables, one telephone cable, and one .Y2-in. conduit lighting circuit are also supported on the trolley-wire hangers, as shown in Figure 1. A 20-in. ventilating pipe and a 10-in. air line are placed as shown, thus acting as a guard to prevent workmen from walking on the track.

Jan 1, 1938

By Francisco Tamargo

"This paper refers to a new process for the full recovery (above 98%) of zinc and other valuable metals (Pb, Ag, Au) accompanying zinc in its concentrates while iron is separated as a marketable product free of any harmful impurities and suitable for sale to the cement industry. The process has been especially designed to achieve the following goals: maximizing the recovery of zinc and those valuable metals that are present in most zinc concentrates (lead, silver, gold); allowing the recovery of other valuable metals such as indium or germanium that could be present in some zinc concentrates; avoiding or minimizing the need for residue disposal in safe areas as it is the common practice nowadays in the zinc industry. Finally, the process achieves the previously related goals at a competitive cost, in line with the existing more efficient operations while using conventional equipment working under atmospheric conditions. The new process can be easily implemented in those smelters using the jarosite or goethite processes as well as in those smelters using direct leaching as a part of the processing facilities. A study has already been conducted on the use of jarosite in the cement manufacturing process, in the raw mix preparation as well as for a set controller. It shows that use of clean jarosite in the manufacture of ordinary Portland cement can result in improved quality of the clinker. Jarosite showed compatibility to influence the burning characteristics of the cement raw mixes. The presence of SO3 bearing mineral phases such as natrojarosite showed the suitability of clean jarosite for use as a set controller in cement production.INTRODUCTION Iron is by far the most abundant impurity accompanying zinc in its concentrates, and consequently, iron residue disposal is a major environmental concern for many zinc smelters in the world. This is especially true during the last 30 years when environmental restrictions became more and more strict. Much research work has been carried out during the last 30 years to try to find a solution for this important issue, but with little success. Only the jarofix process represents a partial solution to this problem as jarofix is stored nearby the smelters with certain limitations as a non-contaminant residue. However, it does not avoid the need to dispose of an important amount of residues every year, representing an environmental liability. Meanwhile, the number of countries limiting or banning the disposal of iron residues generated by the zinc smelters is growing, so that the solution to this problem is becoming an urgent matter right now. At the same time, the lack of appropriate available land for iron disposal is also a major concern in many cases."

Jan 1, 2016

By M. Pourkani, M. Karga, Samid Banis, Andre Laplante, G. Langari-Zadeh

"The Sarcheshmeh mine processes 40,000 t/d of ore grading 0.9% Cu and 0.035% Mo. Grinding is effected in single stage ball mills using 80 mm forged steel balls, with an average consumption of 850 g/t. One of its 5 m diameter, 8 m length ball mills was emptied to measure the ball size distribution. The broken balls were first separated from the total charge, and the remaining balls classified into five size intervals of +7O mm, -70 +60 mm, -60+50 mm, -50+40 mm, -40 mm.The charge was composed of 280,534 balls (excluding broken balls) with a total mass of 305,180 kg. It was found that 4.0 % of the balls were broken; the size distribution of the charge was also markedly different from the desired one, in particular for the small-sized balls. For instance, 9% of the balls were expected to measure 2.54 to 3.18 cm in diameter, but none was found. On the other hand, the amount of top size balls was 30% higher than expected. The radial hardness of balls, which was determined by cutting the balls in halves, showed that the hardness sharply drops when the balls become smaller than 65 mm. The unexpected ball size distribution was attributed to the rapid change in the balls radial hardness. Based on the measured ball size distribution, a new ball make-up charge which uses 80% of 80 mm and 20% of 60 mm balls instead of 100% of 80 mm was proposed and implemented. The effect of the new ball make-up procedure in terms of ball consumption and grinding efficiency is being investigated."

Jan 1, 1999

By X. J. Guo, Q. K. Wang, S. P. Zhong

With depletion of traditional clean copper reserves and fast expansion of the global copper demand and smelting capacity in the past decade, more and more copper smelters have to treat copper concentrate with increasing content of complex arsenic-bearing minerals. Developing economically viable and environmentally reliable methods and approaches for arsenic control in copper smelting has become more critical for sustainable growth of the copper industry. This paper will report the recent effort of Zijin Mining Group Ltd. in developing processes for improving arsenic control and management in the Zijin Copper Smelter. The arsenic distribution and balance data for matte smelting, converting and refining operations in Zijin Copper Smelter is reviewed for understanding of the current challenges in arsenic control. The processes developed for treating the arsenic bearing waste acid bleed stream from the smelting-converting off-gases wet cleaning circuit and the arsenic sludge produced in the refining electrolyte purification circuit for arsenic disposal are discussed. INTRODUCTION With fast expansion of the global copper smelting capacity to meet the world copper demand and depletion of traditional clean copper reserves, more and more copper smelters have to treat copper concentrate with an increasing content of complex arsenic-bearing minerals. China is the world largest copper consumer and also has the largest copper smelting and refining capacity, but majority of its smelting capacity relies on supply of imported copper concentrate. In order to meet the increasing copper demand and ease the tight supply of clean copper concentrate, the Chinese copper industry has to look at the domestic opportunity of developing non-traditional copper resources, specifically those of lower grades, more complex mineralogy, and increasing level of deleterious elements especially arsenic and also process imported copper concentrate with increased arsenic content. Due to a significant and growing environmental issue associated with arsenic contamination, developing economically viable and environmentally reliable methods and approaches for arsenic management and control in unlocking the maximum value of such arsenic bearing copper resources has become more critical for sustainable growth of the industry.

Jan 1, 2019

By Michael L. Wayman

Archaeological and ethnographic work during the last century has shown clearly that metals have played a small but important role in prehistoric Arctic cultures. For at least the past several millenia both iron and copper have been used in the North, primarily for blades, projectile points, knives, awls, engraving tools, fishhooks, scrapers and axes. In addition they were used for joining purposes as staples and rivets. It is of great interest to enquire into the origins of these metals. In this connection one begins with the observation that to date there has been no clear evidence for the smelting or melting of metals in the Arctic prior to the arrival of Europeans. This can be explained partly by the absence of traditional pyrotechnologies such as the high-temperature firing of ceramics and the heat treatment of bone and wood. Another factor which surely inhibited the development of smelting/ melting operations is the relative absence of wood in the region. The production of charcoal for smelting requires large quantities of wood, to the extent that the desertification of a number of areas in the Old World is believed by some to have been at least partly caused by charcoal production. In the North this was obviously not possible. Thus the Arctic peoples were restricted to using native (naturally occurring) metals and metals obtained by various direct and indirect forms of contact with areas of the world where smelting was practiced. Both of these sources were important in the case of iron; we know that meteoritic iron, telluric (native) iron and smelted wrought iron were all used in the Arctic. These three types of iron will be considered in tum.

Jan 1, 1999

By Hans D. Gougar

To meet an increasing demand for minerals, mining operations are moving to ever more remote regions. The lack of a local energy supply and infrastructure, coupled with social and regulatory demands for lowered environmental impact of mining operations, presents an opportunity for a seemingly unlikely competitor ? a nuclear power plant. The Modular Pebble Bed Reactor concept, currently in various stages of research and development around the world, offers a high degree of reliability and safety with minimal consequences for the local or global environment. The passive safety features of this design eliminate the need for the extensive active safety systems that add significantly to the cost of current water-cooled reactors. With the MPBR, as with all nuclear plants, there are no appreciable quantities of waste products released to the environment during normal operations. In contrast with conventional reactor designs, the MPBR would also remain radiologically safe even under the most severe abnormal circumstances. The key to the design is the fuel element. Enriched uranium microspheres are coated with various layers of pyrolytic carbons and silicon carbide to form a highly-temperature resistant particle that effectively retains all fission products. These particles are mixed with graphite and formed into 6 cm pebbles. A randomly packed vessel of such pebbles forms the reactor core through which helium is circulated as a coolant. Computer models and tests performed on actual pebble bed reactors confirm that fuel failure temperatures are not reached even during the most severe conceivable loss of coolant accident. The reactor drives a gas turbine cycle with resulting efficiencies as high as 48%, comparable to natural gas-fired units. The low price of uranium fuel and low maintenance requirements translates into competitive operating costs. However, high capital costs prevent the MPBR from competing with natural gas in most markets. In remote applications where no fossil supplies are readily available, the playing field is more level. This paper summarizes the features of two of the more promising candidates for remote applications and discusses the strengths of the MPBR from the perspectives of fuel supply and environmental impact.

May 1, 2002

By T. R. Madhavan

The development of contact angles on highly polished ?uraninite surfaces, using sodium oleate and dodecyl ammonium acetate as collectors, has been studied at different collector and hydrogen ion concentrations. It was found that sodium oleate in acidic media (up to a neutral: PH) and dodecyl ammonium acetate in neutral and alkaline media give good contact angles. It appears that the combined forms of these collectors, viz., oleic acid and free amine, are more important in effecting contact. W ITH the emergence of uranium as a strategic metal in the last fifteen years, considerable effort has been directed toward the commercial recovery of uranium from its ores. This has resulted in the development of a uranium technology. It is only in recent years, However, that fundamental data regarding the floatability and surface properties of uraninite and ?pitchblende have been elucidated by different methods. Contact-angle measurement is one of the important tools for tl1e evaluation of the conditions of floatability

Jan 1, 1964

By G. A. Gross

"Nearly 90 per cent of the iron ore produced in Canada is derived from iron-formation or bedded iron deposits. About 70 per cent of this consists of concentrates obtained from iron-formation; another 20 per cent was formed by natural enrichment processes.Four principal varieties of iron-formation are recognized -the Algoma, Superior, Clinton and Minette types. Differences in their geology, mineralogy, chemical com-position and environment of deposition are of special significance in their evaluation as ore.The properties of the ores, including grade, beneficiation qualities and minor element content in taconites, metataconites and naturally enriched ores, reflect characteristics of the primary stratigraphie units from which they are derived. A detailed description of the stratigraphie facies is essential for efficient utilization of these source beds."

Jan 1, 1966