Search Documents

By B. Zeifert, C. Martínez-Morales, A. Romero-Serrano, A. Pineda-Rivera, H. Martínez-Gutiérrez, G. Diaz-Sandi

In this work, the effects of CaO/SiO2 ratio and the FeSO4 and FeS2 contents on the stability of the mineralogical species in chromium-based slags were studied. The chemical stability was evaluated by leaching with an acid solution. The main Cr-compounds in slags with FeSO4 and CaO/SiO2=1 were FeCr2O4 and Ca3Cr2Si3O12, while Cr3S4 predominated in slags with FeS2. The slags with CaO/SiO2=2 mainly contained CaCr2O4. The highest Cr concentration levels in the leaching liquors corresponded to slags with CaO/SiO2= 2, and the lowest Cr concentration corresponded to slags with high FeSO4 or FeS2, owing to the stable binding of chromium in the compounds FeCr2O4, Cr3S4 and FeS•Cr2O3.

Jan 1, 2011

By Paul Laframboise, Nigel MacDonald, Mike Hallewell, Robert Thorpe

"Galmoy Mine, owned by Arcon Mines Limited, has operated since 1997, and is one of three operating lead/zinc mines in Ireland. Changes in ore type starting in mid 2002 created challenges to metallurgical operations at Galmoy. This resulted in unacceptable lead and zinc flotation performance, which prompted initiation of a formal plant review and a subsequent stabilization programme. This involved a structured review of operational practices, development of a new Standard Operating Procedure (SOP) which in turn led to significant changes in process control equipment needs in conjunction with extension of zinc flotation cell residence time.This paper will describe the metallurgy of the Galmoy operation. Reasons for the poor metallurgy experienced in 2002 will be described, as well as the solutions identified to overcome these problems. By the second quarter of 2003, these solutions had been implemented and recoveries had risen to record levels.INTRODUCTIONGeneralGalmoy Concentrator is located in County Kilkenny (Refer to Figure 1 below) and was constructed during 1996 and commissioned in 1997.The concentrator at Galmoy had been designed initially to treat 650,000 tonnes per annum of primarily CW ore type. The main mineral of economic significance was sphalerite (Typically 10 to 11% Zn) with some minor galena (0.7%Pb) in a dolomite (Magnesium Carbonate) host rock.The only other competing sulphide mineral was pyrite (Circa 3 to 5% Fe in Mill Feed. This CW ore type predominated the first 6 years of production, but in August 2002, the ore mineralogy changed due to significantly higher levels of pyrite rich G ore body being blended in with CW ore."

Jan 1, 2005

By J. Bednar, R. R. Rogers, W. Dingley

"Zinc is by far the most important metal used for protecting steel from the ravages of corrosion, and cadmium is also used extensively for this purpose. These metals are applied by electrodeposition in cyanide baths when a particularly good appearance and high throwing power are required. One great disadvantage in using these baths has been the decrease in cyanide concentration and the increase in carbonate concentration that takes place during the plating. Another disadvantage has been the development of serious embrittlement in high-strength steels. The present authors have developed new cyanide baths for electroplating both zinc and cadmium on steel. These baths are stable in composition during plating, they have not produced appreciable embrittlement in the high-strength steels that have been investigated up to the present time, and they permit the use of considerably higher plating current densities. In addition, they produce extremely fine grained coatings that are attractive and have excellent adherence and covering properties. Brighteners can be used in the plating baths if bright finishes are required."

Jan 1, 1967

By Ian Hattie, Mark R. Wilson, T. Kurtis Kyser, Brian W. Janser

Petrographic, chemical and isotopic compo itions of auriferous and non-auriferous quartz vei ns from the Sta r Lake and Flin Flin-Amisk Lake areas of northern Saskatchewan indicate diver e origins fo r the fluids associated with gold mineralization. In the Sta r Lake area, the metavolcanic , Star Lake pl uton, and heared mafic dikes have retained their original igneous 81 80 values. The 81 80 value of quartz from mi neralized veins vary by I per mi! and range from+I0 to+IJ. The only quartz ample having a 81 80 value outside th is range came from a vein not associated wi th a dike or gold mineralization . Quartz from the Star Lake pluton has identical 8180 value to the qua rtz from mi neralized vei ns which suggests that the vei ns and the pluton are related to imilar proces es. The diffe rence in 81 80 values between mi neralized and barren vein may erve a a potential exploration tool in this area. Because o34S val ues of a limi ted number of amples of pyrite from gold-bearing quartz vei ns at Star Lake correlate directly with gold content. the gold may have been syngenetic with the su lphur and the 834 value may be useful for exploration . 8180 values of co-existing quartz, calcite, and amphibole in the veins from Star Lake indicate that isotopic disequilibrium among the minerals is common, but the val ues also record a high temperature of formation (ea . 500°C) involvi ng a component of magmatic fl uid. TheoD value of hydrou mineral from Star Lake retain their original igneous values but whole rock values are generally much lower, an effect attributed to interaction of the minerals with a late meteoric water. In the Fl in Flin-Amisk Lake area, auriferou and barren quartz veins formed from a mixture of hydrothermal and metamorph ic flu id at lower temperatures (ea . 350°C) than those at Sta r Lake. Becau e there i no apparent correlation between 8180 values of the quartz with gold content or relative age of the vein , nor between the 834S val ues of pyrite and gold content, table isotopes appear limited as an exploration tool in the Fl in FlonAmisk Lake areas.

Jan 1, 1986

By J. H. Bernard, K. Zak

Abstract- The three traditional types of Variscan vein Pb-Zn-(Ag) mineralization recognized in the Bohemian massif from historic paragenetic studies are confirmed by modern metallogenic studies. Stable C, S, and 0 isotope data, as well as Pb and Sr isotopic ratios of the deposits, indicate a predominantly crustal origin of the constituents in all three types. Although the data also suggest differences in temperature and pressure of formation, and the oxidation conditions and nature of the hydrothermal fluids, nonetheless they are consistent with prevailing metallogenic classifications of the vein mineralization.

Jan 1, 1992

By J. H. Bernard, K. Žák

The three traditional types of Variscan vein Pb-Zn-(Ag) mineralization recognized in the Bohemian massif from historic paragenetic studies are confinned by modem metallogenic studies. Stable C, S, and O isotope data, as well as Pb and Sr isotopic ratios of the deposits, indicate a predominantly crustal origin of the constituents in all three types. Although the data also suggest differences in temperature and pressure of formation, and the oxidation conditions and nature of the hydrothermal fluids, nonetheless they are consistent with prevailing metallogenic classifications of the vein mineralization

Jan 1, 1992

By G. A. Maki, P. J. Fullman, R. G. Roden

"In October 1984, Rocanville Division began using a stacking system to handle potash mill tailings. Previous to this date, mill tailings were slurried to the top of the tailings pile and allowed to debrine while flowing down the pile. With the new stacking system, slurried tailings are fed to mobile stackers. The stackers consist of cyclone packs to debrine the tailings and drag conveyors with screw discharges to deposit the tailings onto the existing pile. This paper deals with the various aspects of the project from conception to its present state.IntroductionPrevious to 1984, when the stacking project was first implemented, potash mill tailings were handled as follows. Mill tailings were first debrined to approximately 65010 solids using a cyclone cluster. The cyclone underflows were then introduced onto a vacuum scroll filter table. Here the tailings were further debrined and discharged into the disposal tank where the tailings were reslurried with reclaim brine and pumped to the tailings disposal site. At the disposal site the slurry was discharged onto the tailings pile and by a natural settling process the tailings were debrined with the brine ultimately collected in the reclaim brine ponds. The shape and profile of the tailings pile was controlled by building salt dykes to control the flow of the discharged tailings slurry. As the tailings pile grew in height, booster pumps were added to the disposal system."

Jan 1, 1990

By P. G. Roden, G. A. Maki, P. J. Fullmann

"In October 1984, Rocanville Division began using a stacking system to handle potash mill tailings. Previous to this date, mill tailings were slurried to the top of the tailings pile and allowed to debrine while flowing mobile stackers. The stackers consist of cyclone packs to debrine the tailings and drag conveyors with screw discharges to deposit the tailings onto the existing pile. The paper will deal with the various aspects of the project from conception to its present state. Key Words: stacking, mobile stackers, Linatex Separators, potash mill tailings, reclaim brine ponds, settling ponds, tailings pile. IntroductionPrevious to 1984, when the stacking project was first implemented, potash mill tailings were handled as follows. Mill tailings were first debrined to approximately 65% solids using a cyclone cluster. The cyclone underflows were then introduced onto a vacuum scroll filter table. Here the tailings were further debrined and discharged into the disposal tank where the tailings were reslurried with reclaim brine and pumped to the tailings disposal site. At the disposal site the slurry was discharged onto the tailings pile and by a natural settling process the tailings were debrined with the brine ultimately collected in the reclaim brine ponds. The shape and profile of the tailings pile was controlled by building salt dikes to control the flow of the discharged tailings slurry. As the tailings pile grew in height, booster pumps were added to the disposal system."

Jan 1, 1986

By W. R. McQuarry, M. E. Wilson

"The structural relations of the ore deposits of the Staclacona mine are of considerable interest, for they not only illustrate the effect of a change in competence of the wall-rock, but also the effect of either the convergence together of two faults, or a change in the clip of a fault, or both of these factors, on ore deposition.The mine is in claim M.L. 1818 near the eastern end of Pelletier lake and lies about 2 miles south of the town of Rouyn. The Company was organized in 1926 to explore claims in Rouyn, Dufresnoy, and Beauchastel townships, but attention was directed mainly to those in Rouyn. Underground work began in 1928 with the sinking of the main shaft to a depth of 300 feet. Except for 1930 and 1931, the mine has been in operation continuously since that time. Production, which began in 1936, up to the end of 1946 has amounted to 1,381,422 tons of ore from which gold and silver having a total value of $7,861,860 were recovered. The average grade of the ore milled in 1946 was $6.68.GEOLOGYThe rocks in which the Stadacona ore deposits occur are mainly volcanics of the (Keewatin) Abitibi series intruded here and there by numerous dykes, sills, or masses of diorite. Single dykes of olivine diabase and lamprophyre are also present in the property and are intersected in the mine workings. The volcanic rocks are part of a wide belt of northward dipping lavas and pyroclastic rocks, having a thickness of over 16,000 feet, that extend from the east-west trending belt of Timiskaming sediments on the south northward to the Horne Creek fault and form the south limb of a large syncline. The volcanic rocks within the property consist of numerous, east-west trending, northward dipping flows of andesite and a few flows of rhyolite interbedded with rhyolite ruff and agglomerate. The angle of dip throughout most of the property is 60° to 80°N., but in the main cross-cut on the 850- and 975-foot levels stratification in rhyolite tuff was noted dipping 35°N. The tuff at this point lies above an intrusive mass of diorite and it is probable that the change in dip results from the way in which the tuff and agglomerate have been thrust aside by the intrusive."

Jan 1, 1954

By G. J. Heferen, A. Pranowo, N. J. Aslin, P. O. Eriksson

Glencore Technology (GT) has over four decades experience supplying stainless steel cathode plates (“cathode plates”) to the electro-refining and electro-winning industry. Cathode plates are typically the single biggest capital investment in a refinery. Refineries may view cathode plates as fixed asset or consumables depending on their operational characteristics. This paper examines the issue of cathode plate life and the strategies and philosophies used by different plants in the management of their cathode plate asset. Some plants operate with their original plates after more than 20 years. Others accept high turnover and regular maintenance as normal operating practice. Reference data are provided on plate life for various operating plants including benchmark plants achieving best-practice plate life and operating cost. The role of the electrode handling equipment on cathode plate longevity is also examined, including latest developments in Cathode Stripping Machine, robotic copper stripping, and full-automation production cranes. The ability to identify and manage the population of plates in service is also critical for maximising plate life and minimising its overall operating cost. This paper discusses a novel and unique RFID system for tracking and managing cathode plate inventory. INTRODUCTION Permanent cathode plates The adoption of permanent stainless steel cathode electrodes in the electro-refining of copper was the most significant process development since the first commercial electro-refineries were built in the late 19th century. It provided significant improvement over the labour intensive and complicated starter sheet system. Copper grows over the permanent cathode blade for a number of days before being stripped, and the permanent cathode can be returned straight back to cells for the next cathode cycle. Glencore Technology (formerly Mount Isa Mines (MIM), then Xstrata Technology) has been manufacturing permanent stainless steel cathode plates from the late 1970s with the birth of ISA PROCESS™, and the Kidd process that came one decade later. Invented and commercialised by Mount Isa Mines, the ISA PROCESS™ was first implemented into Copper Refineries Limited (CRL), Townsville, in 1978. The KIDD PROCESS by Falconbridge evolved in the 1980s and was first implemented into the Kidd Creek Tankhouse, both operations converting from traditional copper starter sheets.

Jan 1, 2019

By G. E. Rowan

"DURING the dark ages, the cherished dream of chemists was to find a process for converting base metal into gold. Many a wealthy-but-gullible patron lost a fortune in the search. Men who work with metals today are a bit more realistic. I haven't heard of a metallurgist who expects to develop any one alloy that will resist all corrosive media. In the field of stain-less steels, there are about forty different types of alloys that are used where corrosion is a •problem.A stainless product is ordinarily selected because it offers one or more of the following qualities:(1) Resistance to corrosion (2) Resistance to oxidation at high temperatures (3) Good mechanical properties at room temperature (4) Good mechanical properties at high or low temperature (5) Attractive appearance (6) Ease of maintenanceToday we are interested in discussing the stainless steel family of alloys because of their .ability to resist corrosion. We• will not try to explain the Theory of Corrosion. Let us assume that, when surface potential and oxide formations are properly controlled, iron will resist attack in various chemi.cal solutions. The addition of alloying elements to iron does this for stainless steels. The principal stainless alloys used by various Canadian industries are listed in the accompanying Table."

Jan 1, 1959

By E. H. Henderson

Introduction Stamp-Milling and amalgamation is, perhaps, one of the oldest processes of recovering gold from its ores. Many papers, theses, and textbooks have been written on the subject of stamp-milling practice in general, but, to my knowledge, there have been no publications describing the modern stamp-mill as designed, developed, and operated in Nova Scotia. Although it may be said that the gravity stamp-mill is the most primitive, and perhaps the crudest, crushing machine in existence, it is at the same time the most satisfactory all-round milling and amalgamating device yet contrived. Originating in Saxony, and used in North America first in Virginia and Georgia, the stamp-mill, in a primitive form, later found its way to California and Colorado. Here, it speedily developed from an affair of wood shod with iron, and operated with the crudest gearing, to substantially its present form. Briefly, it consists (see Figure 1) essentially of a series of hammers (the stamps), which fall upon a mixture of ore and water contained in a cast-iron box (the mortar). The resulting crushed ore (the pulp) is splashed out through a screen on the front of the box. For some years after the discovery of gold in Nova Scotia, in 1861, the ? arrastra and Chilean mill were used to recover the gold from the rich ores. The stamp-mill followed, and various types were used, principally the California and Gilpin County types. Then, in 1895, Mr. M. R. O'Shaughnessy, one of our foremost amalgamators, conceived the idea of a new type of stampmill, which has since become standard in Nova Scotia gold mines. This mill, unique in its design and operation, is specially adapted for the most efficient extraction and recovery of gold as it occurs in our Nova Scotian ores. It is commonly known as the Underwater Feed type, as opposed to the usual Overwater or Top Feed type, and it may be rightly termed The Nova Scotia Self-Classifying Stamp Amalgamation Mill. It is conceded by experienced mill-men that it is superior to any other type of mill for recovering the very coarse and granular gold typical of the ores of this Province. The particular installation and practice to be described in this paper is that of the Guysborough Mines, Limited, at Goldenville, Guysborough county. Emphasis will be laid on certain operating innovations of extreme simplicity and high efficiency.

Jan 1, 1935

By E. H. Henderson

MR. R. V. NEILY stated that he had at one time operated at Goldenville. The practice and results are much the same now as in the olden days. Inside plates were then found to be a source of trouble and had been removed. At the Libbey mine, Queen's county, the sulphides carried considerable gold, and $45.00 to $60.00 per ton had been recovered from the concentrates by roasting and chlorinating. Later, concentrates were treated with bromocyanide. Following that practice, a cyanide leaching plant was installed, which did not require concentration of the tailings. Cyanidation brought a recovery of around 95 per cent, with but $300 worth of plant. In Nova Scotia, the ore of each locality presents an individual problem of its own as to treatment required. Ma. W. B. Timm stated that, in the majority of Nova Scotia gold ores, more than 75 per cent of the gold content is free-milling and, naturally, stamps are most efficient for collecting and amalgamating this gold. In Ontario and the West, they had got away from stamps, and perhaps the main reason was that the supply of battery-men, who came from Nova Scotia, had died off. Ball-mills had been installed, which required smaller space and handled large tonnage, even though, as far as amalgamation goes, the stamps were probably more efficient. If concentration is to be done, ore from stamps is usually in better shape for recovery in passing over the tables, as there is no slime. With the ball-mill, flotation is necessary. The better practice, undoubtedly, is to take out what gold is possible before it is all smashed up, as in the ball-mill, though recent developments in the ball-mill make it possible to trap and take coarse gold directly from the mill. In this way, cyanidation is speeded-up, due to saving of the time the coarse gold would take before going into solution. PROFESSOR A. E. FLYNN found it unusual in these days to read anything in favour of the stamp mill, and thanked Mr. Henderson for the excellent paper in which he upholds the stamps and backs his opinion with facts from actual operations. For the typical Nova Scotia ore, containing coarse gold, stamps are un¬excelled. It used to be said that the virtue of stamps is that they brighten the gold for amalgamation. Although this saying is almost classical, it is not true, for gold is never brighter than in the native, untouched state. Any hammering that gold gets makes it more difficult to amalgamate.

Jan 1, 1935

By Christoph Mueller

Broad band mine communication today is characterized mainly by individual solutions, which have in common their long development phases and their high cost for development, operation and service. The use of Ethernet and TCP/IP on the other side provides an uniquely price efficient combination of high bandwidth open networking, universal use and accessibility of cheap development tools, especially because it forms the technical infrastructure for the worldwide Internet. TCP/IP and Ethernet assures reliable networking however it is not able to guarantee the latency timing of forwarding network information. Therefor, the network design requires strict load limitation and application level traffic control especially if moving equipment has to be manually remotely controlled via the network. To optimize the use of bandwidth on mining networks using load limited, ?bandwidth wasting? local Ethernet segments, long distance broadband traffic should be carried out using more efficient, deterministic communication backbones providing a guaranteed quality of service for each of the physically separated networks. Open networking and broadband systems however may lead to the anticipation that any demands on bulk data or multimedia traffic can be fulfilled in the future. This definitely will not be the case as the bandwidth demands of applications will be growing as least as fast as the bandwidth provided by communication systems. Looking on those problems from an overall system integration perspective, machines and equipment in the future have to be equipped with intelligent computing devices capable of an intelligent local data preprocessing. Such ?Embedded Machine Information Servers? running commercial computing power in the future will be the intelligent bridge between open networking and a secured, high safety local automation system. These ?Embedded Machine Information Servers? then also can make advantage of intelligent video and audio data preprocessing to store and transmit multimedia information ?on demand? or when the application requires it. Summarizing the potential for the future Ethernet based networking together with powerful communication backbones and intelligent local data preprocessing on the machines in the future will lead the way to integrative, reliable and cost efficient mine automation solutions.

May 1, 2002

By W. Grell

"In this paper, two methods of standardizing mill language are proposed; one is based on metric units and the other on English units. Tentative procedures for chemical and screen analysis based on published methods are proposed.Standard procedures for determining work index, and for leaching, flotation, and classification tests are outlined.Objects of Standardization:(1) to improve communication -(a) among gold metallurgists(b) with other branches of mineral dressing(c) with mineral dressing in other countries(d) with general scientific procedure(2) to improve mill control by -(a) standard methods of analysis (i)(ii)(iii)(b) standard methods of calcula tiort(c) standard accounting proceduresin the plantin the mill laboratoryin the assay office(3) to improve mill test work and investigationAreas of Standardization(1) Nomenclature or terminology(2) Measuring techniques(3) Test procedures(4) Accounting procedures"

Jan 1, 1966

By Christoph Mueller

Mining operations are characterized by cost pressure and cycling product prices. A high potential for enhancing efficiency is the integration of all single steps of the mining working chain into a production process structure to make advantage of an optimized flow of material and information through the ?moving ore factory?. As modern mining machinery today is controlled electronically and even already operated autonomously, a smooth and cost efficient flow of data in the mining process will be crucial for cost efficient future mine operations. Therefor, the International Rock Excavation Data Exchange Standard (IREDES) was launched by major players in the industry. The task of this initiative is to define a ?common electronic language? for easy and standardized data exchange between mining machines and central computer systems. As in other industries, this standard is expected to have significant impact on the use of automated equipment. It shall provide easy ways of using multi vendor machine installations in data controlled mining processes. At the same time it reduces cost for individual development of interfaces for all parties involved. Standardized data exchange is also a crucial precondition to integrate the mining process into enterprise level modeling, cost analysis and decision finding systems. The standard?s technical architecture is open and flexible for future applications. It uses modern XML technology enabling easy data exchange with commercial databases as well as open on line networking. The IREDES work is carried out by the initiative members working jointly together in the technical work groups. Prototyping implementations of the Drill rigs profile are currently going on. Further profiles under development cover LHD?s/Loaders/Trucks and Explosives Chargers. The first official release covering the Drill Rigs profile is planned for the end of 2002.

May 1, 2002

By S. Forgeron

Presentation ? Introduction ? Canadian Underground Coal Mines ? Standardization of Geological Assessment ? Geomechanics Base-line Studies of Canadian Coal Mines ? Cape Breton Development Corporation Prince Mine ? Quinsam Coal Corporation ? 2 North and 4 South Mines ? Smoky River Coal Corporation 5B-4 Mine ? Conclusions and Baseline Comparison ? Figures

May 1, 2001

By T. M. Waterland

A GREAT deal of work has been done at Britannia during the past three years in improving and standardizing rounds for development headings, and the results obtained have been very gratifying. The round which has recently been adopted as a standard for all drifts and cross-cuts has, in some instances, doubled the average length of break formerly obtained. It has also increased the footage of advance per labour shift and reduced explosives' consumption. At the present time, with a shortage of skilled labour, more control is necessar7 in directing the drilling of rounds. The use of a standard round has been o great assistance to the foremen and shiftbosses. NATURE OF GROUND Most of the ground encountered consists of a moderately silicified chlorite schist, known locally as G.M.S (green-mottled schist). It cannot be termed hard ground, because a three and one-half inch Leyner will drill at an average rate of twelve inches per minute. Due to the abrasive nature of the ground, the gauge of the steel wears rapidly and in most cases one set of steel is needed for each hole. The ground is not 'free breaking and holes must be spaced correctly to obtain a maximum break. DEVELOPMENT OF STANDARD ROUND FOR THREE-SHIFT OPERATION Late in 1940, a development programme was started involving 7,000 feet of drifting, 6 ft. By 7 1/2 ft. In cross-section, in two headings. Plans were drawn up to advance the headings on three shifts. Equipment used in the headings was as follows: D.A.35 Leyner?machines, Eimco Model 12B mucking machines, nine one-ton end-dump cars, one Mancha Little Trammer on the longest heading, 20-pound rail, 4-in. 15 compressed-air line, 15-in. Fan pipe connected to 5 h. P. Coppus fan. Diamond-drill cross-cuts, 16 feet in length, were cut every 250 feet. Switches were installed at these cross-cuts and they served as passing points for the cars. One siding seventy feet in length was cut in each heading at approximately the half-way point. The cycle of operations planned was to muck out, drill, and blast each shift. Previous performance in this type of ground indicated that a daily advance of 12 feet to 14 feet might be made. However, if a better type of round could be developed, an increased daily advance would be possible. A study of the time available for each operation in a net working shift of six and one-half hours indicated that the maximum depth of round that could be mucked, drilled, and blasted each shift would be six and one-half feet. When this maximum depth was decided upon, the next problem was to develop a satisfactory round. Due to ventilation difficulties and to the short net working shift, the whole round had to be blasted at one time. In other words, no blasting of the cut-holes could be done.

Jan 1, 1942

By L. E. Djingheuzian

"ForewordTHE FOLLOWING excerpt is taken from Fine Grinding Investigations at Lake Shore Mines (C.I.M., Trans., Vol. XLIII, 1940, p. 307):""MacCalman, who has carried out exhaustive testing on the accuracy of screen analysis, makes the following statement in his report, The Accuracy of Sieving Tests, Industrial Chemistry (London, England), Vol. XIV, p. 231:"" 'It will be shown that, as no specific relationship between the sieving value and the various dimensional features of the sieve is evident, though there is an apparent tendency for the sieving value to follow the average aperture size, it is apparently impossible to define the sieving value of a screen from dimensions alone, and the calibration of sieves for important tests on a specific material, whereby the sieving values of these sieves are related to that of an arbitrarily chosen master sieve by correction values, will be recommended."" 'It will be emphasized that these correction values are probably not applicable to other materials, or the same material of different size composition. Sieve users, for important tests or in cases of dispute, will be recommended to calibrate their sieves against a mutually acceptable standard with specified conditions of test, and to recalibrate at intervals' ""."

Jan 1, 1953

By P. Reyes

The start up and operational optimization of the No. 3 Oxygen Plant at the Caletones Copper Smelter of the Codelco - Chile El Teniente Division is summarized. In addition, the economic impact of such optimization on the production cost of oxygen and others aspects associated to the operational robustness as well is detailed.

Jan 1, 2007