Search Documents

By S. P. Cashin, D. Kashuba, W. Esplin

Barrick has had 6 autoclaves in operation at the Goldstrike Mine, North of Carlin Nevada, since 1993. The 6 autoclaves operate in parallel, processing slurry of gold ore. The gold in the ore is predominantly associated with, and encapsulated by, sulphide minerals. It is necessary to oxidize at least 90% of the sulphide mineral before the gold can be concentrated using a cyanide/carbon-in-leach (CIL) circuit. Sulphide oxidation chemical reactions occurring in the autoclaves are exothermic; however, the sulphide content in the ore is not high enough to operate the autoclaves in an auto-thermal mode. Heat from steam is added to the first 2 of 5 autoclave compartments to initiate the sulphide oxidation reactions. The steam used to heat the autoclaves is supplied by three boilers, which are fuelled with propane gas. The completion of a few operations and maintenance projects in the last 2 years has resulted in a 50% reduction in propane energy requirements. The autoclave operating temperatures were minimized. Excess oxygen addition was held as low as possible. The material of construction for the compartment walls inside the autoclaves was changed from brick to Titanium metal. And, the speed of the autoclave slurry agitators was increased. All of these activities had an impact on the propane energy requirements of the autoclaves. Presented below is a description of the autoclave systems, and a discussion of how the energy needs were reduced, resulting in significant operating cost savings.

Jan 1, 2004

By T. Krumins, L. Zunti, R. Frischmuth

Titanium and titanium alloys are commonly selected for pressure oxidation autoclave vent piping and pressure control valve components, as well as autoclave internals, in high-temperature operations. In a vent application, titanium ignition risk is reduced by limiting oxygen concentration, and preventing high gas velocity gas impingement on surfaces. Oxygen concentration is dependent on the autoclave pressure and temperature conditions and therefore titanium ignition risk is dependent on standard operating procedures, and process control interlocks and permissive conditions. It is not uncommon for standard controls to be deficient during atypical operating conditions, or for operations to deviate from the operating procedures, increasing the potential for titanium ignition incident. Titanium ignition risk caused by elevated oxygen concentration in autoclave vent systems can be reduced with the introduction of an online autoclave overpressure calculation and the configuration of associated interlocks and permissive conditions.

Jan 1, 2014

By C. Kennedy, S. Jensen

Traditionally, mineral processing plants are designed to achieve the highest recovery of valuable material with limited regard for the cost of managing waste products-both solid and water components. As an industry, we are confronting ever more stringent environmental standards and lower grade deposits requiring more intensive processing. The most profitable processing route can, in fact, lead to costly issues downstream. Issues or risks associated with waste management include water treatment and handling and storage of potentially acid generating material. The capital and operating costs of dealing with these issues are significant and should be considered as a consequence of plant design and optimisation. The authors of this paper are involved with a number of projects where process operation changes offer opportunities to mitigate risks associated with water and waste management. Examples of these changes will be discussed along with the estimated benefits to the value of the project and reduction of long-term environmental risks. Process changes include 1) the application of in-plant water treatment as opposed to dealing with the entire tailings management facility and 2) the potential to reduce metal leaching and acid rock drainage through the preferential liberation of carbonate minerals in the grinding process.

Jan 1, 2014

By Erik Spiller

"Water and cyanide are highly contentious and conflict issues that many gold mining companies encounter worldwide when dealing with local farming communities, industries and cities competing for water as well as non-government and government organizations. Historically, the gold industry has used processes that required minimum amounts of water to treat and recover gold at locations around the world. Examples are dry grinding for refractory gold treatment in the late 1800s and early 1900s and dry blowing in arid/desert regions to recover alluvial gold. In recent times, new dry processing equipment has been developed and include equipment such as air tables and jigs. Researchers have also modified a Knelson concentrator to concentrate gold from dry solids. High pressure grinding rolls (HPGR) with air classifiers are used to treat industrial minerals and pilot trials have shown that the technology can be applied to comminute refractory gold ores ahead of roasting. Dry stacked tailings is being applied on gold mines to reduce overall water consumption This paper will review the available technologies that in combination may be able to substantially reduce the quantity of water used in the processing of gold ores.INTRODUCTION Water makes up most of the world: the planet is 75% water. Some 97.5% is saline water largely in the oceans, so that only 2.5% is fresh water and useful for human needs. The demand for water is driven primarily by population and concomitant economic growth. Overall, some 70% of the water withdrawn from the environment is used in agriculture, 20% by industry, 7% by households and 3% for mining (Brown, 2003: Maupin et al., 2010). Whilst the water needs of the mining industry are minor compared to those of agriculture, an operating mine requires a relatively large quantity of water on a daily basis to carry out operations. Mining activities are often located in remote, arid environments, with limited access to water. There are a multitude of water resources available to the mining industry for its needs. However, much of this water is saline and over the last two decades there has been a continual decline in water quality (i.e. salinity has increased). In today‘s world, there are enormous internal and external pressures to reduce water consumption at a mine, and/or alternatively use water not considered a resource by the local community. Strategies to meet these objectives can be achieved by implementing good water management practices, by recycling process water, reducing water losses by evaporation and seepage (i.e. by increasing and improving dewatering practices) and employing new technologies such as dry stacking and dry processing (Dunne, 2010)."

Jan 1, 2017

By D. A. Cormode

"INTRODUCTIONPine Point Mines, operated by Cominco Ltd., is located approximately 55 miles east of Hay River, N.W.T. by the southern shore of Great Slave Lake.The milling operation commenced in the fall of 1965 at a design capacity of 5,000 tpd. An addition which came on stream late in 1968 raised the nominal capacity to 8,000 tpd. Currently the milling rate is 11,000 tpd.The lead and zinc sulphides occur in dolomite host rock. Typical feed grades at present are 2% lead, 5.5% zinc and 5 % iron. When dolomite is present even in relatively minor amounts in the zinc concentrate, it presents serious treatment problems and causes inefficient operation of electrolytic zinc refineries.By 1972, it had become apparent that magnesium rejection in the form of dolomite was deteriorating because of increased plant throughput of less amenable ore. This paper will briefly outline the Pine Point zinc flotation circuit and will discuss the two phase program for reducing the magnesium level in the zinc concentrate. The program included changes and alterations to the flotation circuit and the construction of an acid leaching plant."

Jan 1, 1977

By E. Asselin, G. K. Yue

"In the present study, electrochemical measurements, especially cathodic potentiodynamic polarization (CPC) and cyclic potentiodynamic polarization (CPP), have been employed to study the kinetics of ferric reduction on chalcopyrite in aqueous Fe(II)Fe( III)H2SO4 solution at 90 °C and 110 °C. Results from the calculation of speciation in the above solution reveal that, at both 90 °C and 110 °C, the real Fe3+/Fe2+ ratio is much lower than the nominal ratio, which leads to smaller VALUES (for the reversible potential of the ferric/ferrous couple. Exchange current densities of the ferric/ferrous couple were obtained and are on the order of 106 10 5 A/cm2 a t 9 0 °C and 1 07 10 6 A/cm2 at 110 °C, respectively. The Tafel slopes from the CPP method are higher than those from the CPC method at both 90 °C and 110 °C. The transfer coefficients were about 0.360.59 at 90 °C and 0.370.65 at 110 °C. Based on the exchange current densities obtained, the rate constant kc was calculated. It was found that kc at 90 °C was slightly larger than at 110 °C, especially for the results obtained by the CPC method. The average rate constants are 862.17 cm/s for CPC and 65.30 cm/s for CPP at 90 °C, and 477.69 cm/s for CPC and 63.53 cm/s for CPP at 110 °C for nominal Fe3+/Fe2+ ratios ranging from 1:1 to 1000:1. INTRODUCTIONChalcopyrite is one of the most abundant copper-bearing minerals, accounting for approximately 70% of the world’s known copper reserves (Wang, 2005). Most of the currently proposed leaching processes are based on sulfuric acid with ferric ions and/or dissolved oxygen as oxidants. Some of these processes have been piloted in attempts to implement these technologies on an industrial scale, such as Activox (U.S. 5,232,491, 1993), Nenatech (U.S. 5,993,635, 1999), Dynatec (U.S. 5,730,776, 1998), AAC/UBC (U.S. 6,503,293, 2003), Total Pressure Oxidation (U.S. 5,698,170, 1997), CESL (U.S. 5,874,055, 1999) and Galvanox (U.S. 7,846,233, 2010).To date, much effort has been devoted to understanding the kinetics and mechanisms of the oxidative processes (Biegler & Horne, 1985; Córdoba, Muñoz, Blázquez, González, & Ballester, 2008, 2009; Ghahremaninezhad, Asselin, & Dixon, 2010; Hirato, Majima, & Awakura, 1987; Hiroyoshi, Kuroiwa, Miki, Tsunekawa, & Hirajima, 2004; Warren, Wadsworth, & El-raghy, 1982) or the cathode reduction reactions of chalcopyrite itself (Arce & González, 2002; Biegler & Swift, 1976; Biegler, 1977; Nava, González, Leinen, & Ramos-Barrado, 2008), by chemical or electrochemical methods. However, as the most important cathodic processes in chalcopyrite leaching systems, the cathodic reductions of ferric ions or dissolved oxygen are worth measuring due to their effects on the overall leaching rate, as predicted by mixed potential theory."

Jan 1, 2012

By M. Wu, G. Plascencia, A. E. M. Warner, A. Vahed, T. A. Utigard

Nickel oxide granules formed by pyrohydrolysis of a chloride solution, were reduced in hydrogen. Below 400 °C, an incubation period was observed, followed by very slow reduction. In the temperature range from 400 to 600 °C, the rate of reduction increased with increasing temperature and increasing hydrogen pressure. Microscopic analysis showed that in this temperature range the reaction followed the shrinking core model. Above 600 °C, the reduction rate decreased noticeably before suddenly becoming very fast at and above 950 °C. Microscopy showed inner bands of metallization inside the outer metallic rim, indicating partial blockage of the interface between the reacted and un-reacted NiO core. At these temperatures, particle agglomeration and sintering were also found to take place. Surface segregation of sulphur may account for the slow down in reduction rate above 600 °C. From an industrial point of view, reduction should be carried out from 550 to 600 °C with as high a concentration of hydrogen as possible. If sintering and agglomeration are not of any concerns, reduction can be carried extremely fast at about 1000 °C.

Jan 1, 2005

By A. Fyson, M. P. Smith, Margarete Kalin

"Drums containing 0.07 m3 of pyritic waste rock from a zinc/copper mine, with and without Natural Phosphate Rock (NPR) additions (40 kg/t waste rock) were set up outdoors. The effluent chemistry has been monitored over a period of 709 days. In the presence of NPR, the cumulative acidity discharged from 7 out of 8 drums was 80 % less than that discharged from drums without NPR. Mixing NPR throughout the drums was more effective in reducing acidity than placement of the NPR in a layer in the drum. NPR treatment was more effective for 'fresh' waste rock than for material which had weathered for more than 4 years. It is concluded that application of NPR to pyritic waste rock could greatly reduce acidity generated.IntroductionWaste rock dumps are significant sources of acid, generated by the oxidation of sulphides. Oxygen and water supply are oxidation rate-controlling factors, and oxygen supply is the reaction-limiting component. If secondary minerals can be formed on the surface of the rocks, pyrite oxidation and therefore acid generation may be reduced or inhibited. Neutralizing agents such as limestone do not prevent the oxidation of pyrite but treat the resultant acid mine drainage (AMD) or acid rock drainage (ARD).Meek et al. (1991) determined in pilot scale experiments that apatite mixed with tailings was more cost effective than liming or use of PVC liners to reduce oxygen and water penetration into the tailings. Phosphate is not acting as a neutralising agent but it creates a chemical condition on pyritic surfaces which prevents reactions of the oxidising agents. Precipitation of principally iron phosphates physically isolates the pyrite surfaces from further oxidation (Ziemkiewicz 1990; Evangelou 1994). The chemistry of the phosphate effects has been described by Spotts and Dollhopf (1990). Secondary mineral formation was evident in the leach pile at Gibraltar when leaching was impaired (Scott, 1991) indicating a link between oxidation and the mineral-formation process. This paper reports on effluent characteristics when waste rock is generating acid in the presence of NPR."

Jan 1, 1995

By G. Tairova, J. Ioffe

Arsenic, selenium and mercury species are common contaminants in mining aqueous streams and present significant environmental and health problems. The objective of this project is to investigate methods to lower the concentrations of these elements in mining aqueous streams. A new composite media for removal of these elements of concern from mining effluents was developed. The results of bench scale and pilot plant experiments, using the media, indicated removal of arsenic, selenium, mercury and other elements of concern below detection limits.

Jan 1, 2014

By S. D. F. Rocha1, L. Katsarou, G. P. Demopoulos

"Crystalline scorodite (FeAsO4·2H2O) has been pointed out as the most stable compound to immobilize arsenic for disposal due to its good stability performance according to EPA’s TCLP test. However, in anaerobic conditions, arsenic releasing is increased to undesired levels due to scorodite reductive break down, in eh <100 mV at 5.5< pH <7 which causes contamination of groundwater. In this work, the concept of encapsulation by controlled deposition of mineral coatings immune to pH or redox potential variations is presented. Aluminum and calcium phosphates were evaluated as coatings and the release of arsenic from scorodite previously coated with phosphates was substantially decreased when compared to the VALUES (obtained from crude scorodite, both in oxic and anoxic conditions. INTRODUCTIONThe widely acknowledged hazardous properties of arsenic as a soil and natural water contaminant and its adverse health effects when present in drinking water have led to very strict environmental regulations (Mandal & Suzuki, 2002) aiming at the drastic reduction of the presence of arsenic in the effluents of the mining and metallurgical industries.In Canada, the Metal Mining Effluent Regulations (Government of Canada, 2002) dictate that the maximum monthly mean concentration in tailings for arsenic must be lower than 0.5 mg/L. At the same time the new Environmental Protection Agency’s (EPA) standard for drinking water foresees concentrations of arsenic less than 0.01 mg/L, which means that the leachability limit for the industrial waste is set at 1 mg/L arsenic (EPA, 1994; Le Berre et. al, 2007). One of the preoccupations of the mining and metallurgical industries is directed to the elimination of arsenic presence in all its effluents, especially since arsenic is commonly found in many ores mainly in the form of oxides and sulphides. After processing of arsenic-containing ores and concentrates, arsenic can be present either in solid residues and tailings, liquid effluents or in flue dusts. Several of these forms of arsenic waste materials are soluble and therefore may cause the contamination of ground water, if disposed of without further treatment."

Jan 1, 2012

In the flotation of a copper ore, entrainment of fine silicate and iron sulfide gangue minerals resulted in poor copper concentrate grade. In the cleaning stage, rejection of these gangue minerals was particularly difficult due to severe mechanical entrainment when the rougher concentrate was ground to 10 µm. To reduce gangue entrainment, polymeric depressants were tested. The rationale being that with the use of such polymeric depressants that also possess flocculation power, not only minerals-to-be-depressed can be made hydrophilic, but their particle size can also be enlarged. In this manner both the "genuine" flotation and the mechanical entrainment can be reduced. An effective polymer to reduce entrainment of silicate gangue mineral in sulfide flotation was identified from bench flotation tests conducted on single minerals. It was then applied to the flotation of a copper-gold ore confirming the beneficial role of the polymeric depressant in the reduction of fine gangue entrainment.

Jan 1, 2007

By S. Y. Ezz, K. El•Guindi

A vertical tube, 8 m long and 2.5 cm in diameter, electrically heated to 650°C throughout the majority of its height, was used to study the-effect of ore feed rate and hydrogen flow rate on the reduction of fine iron ore particles. A correlation could be obtained between the combined effect of the amount of reducing gas and reduction time and the per-cent reduction. The results suggest that a method based on the reduction of fine iron ores while falling through up-streaming hydrogen cannot be recommended for industrial application.

Jan 1, 1969

By Martin Froehling, Curtis Mohns, Rahim Rajwani, Michael Fullam

"The Kemess mining and milling complex is operated by Northgate Minerals Corporation and is located in the mountains of north-central British Columbia, 430 kilometers northwest of Prince George. The complex consists of the Kemess South open pit mine and a 52,000 tonnes per day mill. Hypogene, supergene and leach cap ores are processed using conventional crushing, grinding, and flotation techniques to produce gold-copper concentrates with minor by-product silver value.The rougher flotation concentrate is re-ground in closed circuit before being cleaned to final concentrate grade. Historically, gold losses in the cleaner tailings were primarily associated with pyrite, with only minor amounts of free gold. More recently, with the processing of high pyrite ores, the major losses were found to be free gold less than 10 microns in size. The fine grind required for the high pyrite ores resulted in over-grinding of the free gold particles in the regrind circuit, contributing to poor flotation characteristics. It was thought that if this free gold could be recovered by gravity at coarser size in the regrind circulating load, the free gold losses in the cleaner tailings could be reduced.Preliminary test work carried out by Knelson Gravity Solutions indicated the potential for free gold recovery in the regrind circuit. A Knelson XD-30 Concentrator was installed with variable speed capability, and a series of optimization tests were carried out. In addition, cleaner tailings were characterized with gravity operating and with gravity not operating to determine the overall gold recovery benefit. The single Knelson XD-30 installation recovers ~10% of the total gold in the regrind circuit and increases overall recovery by 3% when high pyrite ores are processed."

Jan 1, 2007

By K. Prajapati, P. Hes

Transmission of vibration to the operator from percussive vibrating tools is increasingly of concern in industrial and mining applications. Prolonged exposure to high levels of vibration transmitted via the hand causes disorders known as hand-arm vibration syndrome (HAVS). The vascular component of HAVS is called vibration white finger (VWF) and has a debilitating effect on the hand. Vibration at frequencies below 1250 Hz, a tight hand-grip force and cold environments are reported to increase the likelihood of developing VWF. A vibration damping handle design with patents pending that addresses some of the causes of VWF has been developed and retrofits onto jackleg pneumatic rock drills. The handle is decoupled from the drill while maintaining jackleg twist-grip controls on the hand-grip using a combination of sealed self adjusting hydraulic pistons and compliant materials in series, and a new air control valve. The ergonomics of the hand-grip was also modified by the addition of a polyurethane sleeve with a diameter of 50 mm. The new hand-grip reduces direct cold metal contact and minimizes grip force. Measurement of vibration as the quantity acceleration was made in accordance with international standard ISO 5349. Overall vibration damping in all axes of 50% to 63% was attained at frequencies below 1250 Hz. The dimensions of the damping handle are comparable and its weight is only 100 g heavier than a standard handle.

Jan 1, 2001

By A. Warczok, T. A. Utigard

"Slags from smelting of copper concentrates contains from 1 to 15% of copper. Copper is present in the form of copper or copper matte inclusions of size from 2 to 1000 micro, and as dissolved cuprous oxide. Removal of the copper requires the slag reduction, primarily reduction of magnetite and co-reduction of cuprous oxide. Thus, the kinetics of the slag reduction play an important role in copper recovery. Instantaneously, at the contact of carbon and a slag the gaseous film is formed. The magnetite and cuprous oxide reduction is going through a gaseous film, separating the slag and carbon of a coke or electrodes. The thickness of a gaseous film grows to a critical value and gas bubbles, containing CO and CO2, are created and rise up in the slag. Results of measurements of kinetic of the slag reduction with graphite showed high value of activation energy, close to the value of activation energy of Boudouard reaction. Strong temperature dependence of the reaction rate points out the thermal instability of the reacting system. It was found that the slowest process in the reduction stages determines the loop of CO and CO2 transfer and magnetite diffusion to the slag/gas film boundary. Strongly endothermic Boudouard reaction seems to cause thermal instability on the reaction surface. So, heat transfer to the reaction surface is very important. Due to low thermal conductivity of a slag the convection dominates in the heat transfer. So, any slag stirring accelerates the rate of reduction and coalescence of metallic copper or copper matte inclusions."

Jan 1, 2015

By Nitin Bhavsar, Kaushik Vakil, Lakshmikanth Reddy, Sanjay Sarkar, Tathavadkar. Vilas, Bhavin Desai, Raghavendra Adiga

Gold and platinum group metals (PGM) do not dissolve in sulfate electrolyte from anode during electro-refining of primary copper. The PGM form solid ‘slimes’ which accumulates at bottom of the electrolytic cell. Typically, 8 to 10 ppm silver is present in copper cathodes, which is equivalent to almost 2% of silver loss during electro-refining. The silver can be cemented with cathode copper as soon as it is dissolved into the electrolyte from anode or during entrapment of slime particles in cathode. Over a period of time, the concentrates grade has deteriorated and change in type & amount of impurities in concentrate has resulted in higher silver loss during refining process. Therefore, an in-depth investigation was carried out in both fire- and electro-refining processes to understand the root causes of higher silver loss in copper cathodes. The detailed characterization and the plant data analysis were carried out. The results of study revealed that higher silver loss in 3rd crop cathodes as compared to 1st and 2nd crop cathodes from same anode. In anode silver was present in two forms, dissolved in copper (solid solution) and in slime phases such as Cu2-xAgxSeTe. SEM-EDX study of anode cross section confirmed higher silver and oxygen content in central region (core) of anode as compared that in both air and mold sides. This is due to non-uniform cooling of anode which was confirmed by the solidification modeling. Higher concentration of oxygen & silver at core of anode rised Ag+ concentration in electrolyte and slime particles during 3rd crop. The results of study were used to optimize the anode cooling process and also electrolyte chemistry to reduce the silver loss. The details of study carried out are discussed in this paper using the results of modeling, characterization and experimental studies. INTRODUCTION In the electrolytic refining of copper, fire refined copper anodes are used as raw material. Anodes contains copper of the range 99.5 to 99.6%, rest being the impurities. Hence, the purpose of the refining is (1) to remove the impurities so that final cathode conforms to the LME specifications and also (2) to recover the precious metal from the anode copper. When anode is dissolved, most of the impurities reports to the anode slime settled at the bottom of the cell, and rest dissolves in the electrolyte. Dissolved impurities remains in electrolyte and are removed during electrolyte recycling. However, sometime dissolved impurities and slime particles get entrapped in cathode due to disturbances in operational conditions. Metals dissolving in the electrolyte are the elements such as Ni, Co, Fe, Zn. The electrode potential of As, Sb and Bi being close to that of copper, these elements partly dissolve in the electrolyte. Noble metals like Ag, Au, Pt and Pd are generally insoluble and are thus expected to report to the anode slime. A small amount of the sliver content from the anode is dissolved in the electrolyte. Because the dissolved silver electroplates on the cathode at a smaller applied potential than copper, the cathode typically contains up to 8 ppm of silver. This is referred to as ‘silver loss’ in cathode (Cooper, 1987). Fortunately, silver is a rather benign impurity in copper due to its electrical conductivity being higher than copper. However, higher silver loss in cathode is loss of revenue for Copper smelter due to significant difference in their LME price.

Jan 1, 2019

By G. Tairova, M. Murchie, B. Esford, E. Lam

"The objective of this project is to investigate methods to lower the sulphate concentrations in the mill effluent. Currently, the concentration of sulphate in mill effluent is approximately 2 g/L. The high concentration of sulphate ion in the effluent has the potential to become a regulatory issue. The target sulphate concentration in mill effluent for this work was less than 500 mg/L. The pilot studies, using sulphate precipitation, were carried out at the mill. The results of the sulphate precipitation pilot study, using calcium hydroxide and sodium aluminate, indicated that:• The sulphate concentrations in effluent could be reduced to less than 500 mg/L.• The concentrations of most other elements of concern, such as selenium, arsenic, cobalt, nickel and vanadium, were also reduced.INTRODUCTIONHistorically, the concentration of sulphate, SO4 2-, in water has not generally been subject to regulation. However, with the increasing global consumption of water, stricter regulations on sulphate quantity may be imposed. Sulphate is a concern in process waters as it forms scale on process equipment and leads to operational problems. High sulphate concentrations may result in adverse health effects. The taste theshhold for the most sulphate salts in drinking water ranges from 250 to 500 mg/L.A literature search and review to identify methods to reduce sulphate concentration in the mill effluent was carried out. A number of methods were selected and tested in the lab. The experimental results indicated that the precipitation methods, using calcium hydroxide and aluminum compounds, barium compounds, as well as the ion exchange and the membrane methods, were effective for the removal of sulphate to below the required limits. Some other elements, such as vanadium, nickel, cobalt, selenium and molybdenum, were also removed.The process, using calcium hydroxide and aluminum compound for sulphate precipitation, similar to the Cost Effective Sulphate Removal (CESR), also known as “Walhalla” process, described in the Montana Tech report (“Demonstration Of Sulfate Removal” 1999), was selected for further consideration [1]. In the CESR process, the water is treated with lime for precipitation of gypsum, followed by the reaction with a proprietary aluminum compound for removal of a residual sulphate. The final pH adjustment is carried out using carbon dioxide. Results of a preliminary cost estimate indicated that the removal of sulphate using calcium hydroxide and aluminum compound was the preferred method of treatment, considering its low cost, availability of chemicals and minimal changes to the existing plant circuit."

Jan 1, 2012

By D. Sanguinetti, A. Consigny, M. Nodwell

"Alkali precipitation of dissolved metals is an inexpensive but non-selective means of treating mine wastewater. Alternatively, sulphide precipitation can treat to below parts-per-million concentrations while selectively recovering valuable metals. While technically feasible, sulphide treatment of dilute waste streams increases the size and cost of the plant relative to the metals loading. Ion exchange has been applied at two separate sites to pre-concentrate nickel containing wastewater prior to recovery in smaller and more cost effective sulphide precipitation circuits. The result is a dual-circuit system that can maintain high selectivity and reduce overall facility cost while meeting strict effluent regulations.INTRODUCTIONAlkali precipitation using lime is the most common method of treating mining effluents for dissolved metals removal. This method is generally sufficient for waste streams containing mixed metals of little value, and for meeting modest metal concentration limits in the final effluent. Due to the non-selective nature of the lime process, the produced metal hydroxide sludge is of little value. All metals are removed together in a sludge product which cannot be re-processed for further value recovery.By contrast, sulphide precipitation can be used to selectively remove and recover valuable base metals (such as copper, zinc, nickel and cobalt), since the sulphide will preferentially target these metals without reacting with less valuable metals (such as iron and aluminum). The low solubility of the metal sulphide solids also supports the removal of base metals to lower concentrations than can be achieved with alkali precipitation in addition to other benefits discussed more fully in a prior paper (Bratty, Lawrence, Kratochvil & Marchant, 2006). The corollary to this solubility feature is that sulphide precipitation can function on influent streams containing low (< 10 mg/L) metals concentrations to meet very low parts-perbillion final effluent concentrations. Reagent overdosing is also minimized when compared to alkali precipitation."

Jan 1, 2012

By N. A. Jabit

The dissolution behaviour of ilmenite in acid solutions has been studied by many researchers to improve the leaching efficiency. Most studies which utilized natural ilmenite from different origins resulted in different reactivity due to the alteration caused by the weathering process. Previous researchers have suggested that the greater reactivity shown by some ilmenite samples towards sulphuric acid may be a result of the mineral being relatively unaltered. In the present study a rotating synthetic ilmenite disc of 2.2 cm diameter was subjected to leaching studies in hydrochloric acid. The dissolution rates of iron and titanium from synthetic ilmenite were determined in hydrochloric acid solutions (4 M to 9 M) over a temperature range of 50 to 80°C. Results show that the rate of dissolution of both iron and titanium increased with the increase in acid concentration. However, the rates decreased with time and obeyed a parabolic rate law indicating the blockage of the surface by an insoluble product. The rates of dissolution of both iron and titanium were higher in the presence of SnCl2 and remained unaffected with time indicating the reductive role of SnCl2 which inhibits the formation of surface blocking solids. Application to natural ilmenite is also discussed.

Jan 1, 2014

By L. C. S. Dharmasiri, S. M. Shin, A. Senaputra, J. S. Sohn, K. H. Park, J. Avraamides

Reducing agents can be applied to leach metal values from natural and secondary resources such as laterite ores and deep sea manganese nodules and recycled materials such as spent batteries / catalysts which contain high-valent metal oxides of manganese, cobalt and iron. Selective leaching of some metals can be achieved by selecting conditions to control the saturated solubility and dissolution rates of metals from oxides or mixed metal/oxide matrices. The leaching results are rationalized on the basis of chemical species, Eh-pH diagrams and heterogeneous kinetic models. The role of reducing agents such as hydrogen peroxide, sulfur dioxide and iron(II) sulphate, in acid, alkali and in the presence of complexing ligands such as ammonia for the improvement of the leaching of metal oxides and metals is discussed. Previous studies on acid leaching of metals from nickel laterites, manganese nodules and spent catalysts/batteries in the absence or presence of reducing agents show that the rate controlling step involves the diffusion of protons through a thickening product layer on the particle being leached. It is shown that the leaching of nickel and cobalt from manganese nodules and zinc-carbon batteries in ammoniacal sulphur dioxide solutions also obey shrinking core kinetics.

Jan 1, 2014