Search Documents

By J-F. Béland, N. Parson

Aluminum extrusions are widely used for automotive crash management systems due to their superior specific energy absorption capabilities, as compared to steel. The Al-Mg-Si alloy series can be readily extruded into complex multi-hollow profiles, as required in crash systems, and can be used to target a range of desired strength levels. This paper focuses on the development of an axial crush test protocol and evaluation of the crush performance of common 6XXX series alloys for a variety of tempers. The observed crush behaviour is then compared to tensile test results.

Jan 1, 2015

By C. Doucet

Since 2001, CANMET Mining and Mineral Sciences Laboratories (MMSL) have worked with Falconbridge Ltd. (now Xstrata Nickel) to evaluate trends in the strength development and water retention properties of a novel backfill material for underground mining, called gelfill. Between 2004 and 2006, extensive laboratory tests were undertaken under the leadership of the Deep Mining Research Consortium (DMRC). This paper compares results obtained from samples circulated through a mini-flow loop and a simple mixer. Although many parameters were studied over the last five (5) years, this paper focuses on the investigation of the effect of the mixing method, sequence and time, and the curing environment on strength development and water retention of gelfill. It was found that binder should be added as a powder to the mix in the mini-flow loop, and that mixing slurry in the mini-flow loop as opposed to the mixer generally yielded higher strengths. The practical implications of these observations are the subject of an on-going underground trial that will compare laboratory and in situ properties of regular slurry fill with gelfill.

May 1, 2007

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, K. Fountain

"A comparison of data from INPUT, GEOTEM, and MEGATEM airborne electromagnetic (AEM) systems over the Aldermac deposit, Québec, Canada, was undertaken to evaluate the relative ef¬ficiency of these systems for the detection of small, deep conductors. The Aldermac orebody was mined between 1933 and 1934 to a depth of 200 m. A deeper mineralized zone was discovered in 1987. The MEGATEMII system was used to acquire 90- and 30-Hz data over the deposit in 2003 as part of a research project. These MEGATEMII data were compared with data acquired by other AEM systems (GEOTEM and INPUT), and the results show that the MEGATEMII response is ten times larger than the other sys¬tems. For the dB/dt response, 30 Hz gives a better signal-to-noise ratio, whereas 90 Hz has a better signal-to-noise ratio on the B-field.The data were evaluated by numerical modeling. The deposit was best represented by a complex mod¬el, comprising two weakly conductive bodies to approximate the alteration halo, two deeper prisms repre¬senting known orebodies, and three bodies ranging in thickness from 3 to 6 m and in resistivity from 12 to 20 ohm·m, representing the chargeable overburden. This implies that the MEGATEMII system is able to see a small conductive body at more than 200 m depth in an area where the response is contaminated by conductive overburden."

Jan 1, 2009

By F. Moraw

The use of redox fuel cells in which oxygen is replaced by other oxidants such as ferric ions can have significant advantages [1-3]. For example, the cathodic reaction rate (e.g., exchange current density) can be increased by several orders of magnitude compared to the oxygen reduction reaction, and platinum group metal (PGM) catalysts are not required. As a result of the higher aqueous solubility of the oxidant in a redox fuel cell compared to that of oxygen the rate of mass transfer (e.g., limiting current density) is greater by several orders of magnitude. The redox fuel cell can achieve high efficiencies and has other fuel cell advantages. The main issue with the redox fuel cell cathode is the regeneration of the oxidant where low conversion efficiencies are achieved even with platinum group metal (PGM) catalysts. In the work discussed here the Fe3+/Fe2+ redox fuel cell cathode is characterized over a range of electrolyte concentrations and operating conditions, and electrode materials. Cyclic voltammetry and electrochemical impedance spectroscopy are mainly used for electrochemical characterization and mechanistic determination of the cathode redox couple. Further characterization with selected compositions and materials is done in a redox fuel cell (hydrogen - Fe3+/Fe2+). The mechanism and the advantages and disadvantages of the fuel cell redox cathode are discussed with respect to other approaches and other redox couples.

Jan 1, 2005

By H. Wyslouzil

"The Kelsey Centrifugal Jig is a gravity separation device which utilizes the principles of the conventional mineral jigs but with the additional feature of being able to vary the apparent gravitational field. This is accomplished by utilizing the specific induced movements of the conventional jig within a centrifuge.Pilot plant trials have been underway since July 1988 to evaluate the potential applicability of this technology to various process streams at Rio Kemptville Tin.The grade/recovery relationships for samples treated in the jig were consistently better than results obtained from tables. Recoveries of more than 90% were attained at concentrating factors ranging up to 20. When compared with electrostatic separators, the jig achieved equivalent metallurgical results in a two stage process, without the expensive requirement of filtration and drying. Recoveries exceeding 96% were achieved with final concentrate grades averaging higher than 60% tin.INTRODUCTIONMineral jigs have been used for hundreds of years. Many different types have been developed, and each one has numerous variations. In recent years, the idea of applying centrifugal forces to conventional jigs has been put to practical tests and today a number of units are in commercial production. In principle, by enhancing the apparent gravitational field, it should be possible to recover finer particles by overcoming viscosity and surface effects which tend to limit existing gravity devices. In addition, it may be possible to use gravity to separate minerals with much smaller specific gravity differences."

Jan 1, 1990

By M. Courchesne, C. Barbery, D. Hodouin, C. Carrier

"The carbon-in-pulp process for recovery of gold dissolved in dilute cyanide solutions, in the presence of solids, has now replaced the convedntional processes of pregnant liquid/barren solids separation followed by Merrill-Crowe precipitation. Most plants built over the past ten years incorporate a CIP section. The process is described as cheaper in capital and operating costs, and few major start-up or operational difficulties are reported. For the purpose of the present paper, the CIP process will be assumed to consist of the following sequence of operations (Figure 1):- the slurry stream coming out of the cyanidation circuit is first screened to remove any tramp oversize material. Gold dissolution is assumed to be complete before entering the CIP circuit.- the slurry is sent into a series of agitated tanks in which it is mixed with activated carbon. The carbon particles size is much coarser than the top size of the ground ore. The tanks are fitted with screens that allows the slurry to overflow continuously into the next tank, while retaining the carbon in the tank. Slurry dilution is adjusted to prevent carbon from settling in the tanks. Agitation intensity is kept low in order to minimize carbon abrasion.- carbon is transfered from tank to tank in a discontinuous manner. According to a specific schedule, the carbon from tank one is removed, then carbon from tank two is sent to tank one, and so on, till the last tank, which is filled with regenerated carbon corning from the elutionregeneration section. The amount of carbon removed, the transfer from tank to tank, the sequence of transfer, the carbon inventory in the various tanks are parameters which are, up to a point, at th2 discretion of the operators, as long as they remove, batch wise, an amount of loaded carbon containing a similar quantity of gold to the one that has entered the circuit since the last transfer."

Jan 1, 1987

By Caroline B. Chapleau, Mélanie Proulx, Claude Bazin, Gaétan Lavoie

"Quebec Cartier Mining operates a pelletizing plant in Port-Cartier, QC. Grinding, agglomeration and pellets induration are the three main steps in the preparation of iron oxide pellets. In 1998, following different recommendations, the company increased the speed of one of its ball mill in order to increase the grinding efficiency of the machine. As expected, the increased speed lead to an increase of the power draught, which did not produce the expected increase of fineness of grind, neither its allows to increase the mill throughput. The change of behaviour of the mill could hardly be understood by comparison of discharge size distribution at initial and modified mill rotation speed. On the other hand, the use of the selection function from a population balance model provides an insight of the changes that occurred in the mill. This paper reviews the various steps required for the estimation of a grinding mill selection function. Results of the calibration to Quebec Cartier grinding mills show that the increase in the mill speed leads to higher rate of breakage of coarse particles, at the expenses of less efficient breakage of medium and fine size particles. In the case of the studied mill, breakage of coarse particles was probably not the critical step of the mill operation. INTRODUCTIONOre size reduction is the major energy consumption step in any mineral processing operations (Austin et al., 1984). Size reduction is required to either liberate valuable minerals from the gangue minerals in which they are imbedded, or to increase the specific surface of the ground material. Plant engineers continuously face the challenge to find grinding machines, operating conditions or grinding circuit flowsheet configurations that could improve the size reduction process at lower energy or m6dia consumption."

Jan 1, 2000

By J. G. Kim, B. G. Chae, D. S. Cheon, E. S. Park

The underground structures such as high-level radioactive waste disposal thermal energy storage should be designed and constructed considering thermal-mechanical characterization because of long term and/or cyclic thermal stress. High temperature changes in these structures can extend the existing cracks and generate new cracks in surrounding rock mass. In case of long term and/or cyclic thermal stress conditions, it is possible to lose the function of structures caused by the significant cracks and fracture growth in the rock mass. In this study, the critical thermal crack temperature of the granite, limestone and thermal Kaiser effect were evaluated. Experiments were carried out with the heating speed of 1.5?/min. To avoid thermal shock and target temperatures were set at 150? and 250?. In order to verify the thermal Kaiser effect, the samples were heated by 150 ? after 2-3 repetition to 250?. The generation and growth of cracks were observed through an acoustic emission measuring system. The variation of the physical rock properties was measured before and after thermal experiments. After compared with the thermal experiments using PFC2D, numerical simulations were carried out at higher temperatures (400?). The experiments showed that the initial thermal crack temperature of granite and limestone is about 35?, 32? and the critical thermal crack temperature were about 69? , and 49? , respectively. The experiments confirmed the thermal Kaiser effect of experimented granite and limestone due to thermal cyclic loading. From the numerical analysis, the critical crack temperature showed the same tendency as the thermal experiments. The P and S wave velocity of the sample after the experiment were reduced. Therefore, when heat is applied in long-term and repetitive conditions, these cracks may affect the function and stability of the underground structure. Therefore, further studies of thermal stress effects should be performed.

Jan 1, 2015

By J. M. Menacho, J. M. Reyes

"Batch and continuous regrind tests were conducted in 3 kW and 15 kW tower mill units, respectively. Single particle size classes of a chilean copper sulphide concentrate were employed in the batch tests, while a fraction of the plant stream was deviated to the continuous unit operated under different conditions.Results are interpreted in terms of the simplified grinding kinetic model energy-based and conveniently adapted to this application. Based on the above figures plus some industrial data supplied by MPSI Inc., a scale-up relationship was developed for the apparent specific rate of breakage siE, as a function of the net power draw P, i.e.siE = siE text (P/P test) 0.089This equation fit very well the available data at the three scales and its application to regrind 4400 t/day of rougher copper concentrate from 70% below 325 Tyler mesh to 95% below same mesh, involves around 30% energy-saving compared to standard ball mill for same grinding task.INTRODUCTIONImpact and abrasion-attrition breakage are two extreme mechanisms present in any grinding system in a proportion defined by specific design and operating conditions. Impact breakage is generally efficient for coarse grinding, while abrasion-attrition is adequate to produce fine particles. Efficiency of conventional tumbling mills decreases as fineness of the product increases, even though distribution of applied stresses is always much stronger than internal force distribution in the particles. On the other hand.in a vertically stirred ball mill like the tower mill, distribution of applied stresses and particle strengths are in the same order of magnitude, making possible nearly ideal abrasion conditions (1).Tower mill configuration includes a cylindrical body vertically mounted and provided with a central screw with flights to produce circulation of balls moved up through the inner region to return down by the external space. Fresh material can be fed into the top , center or bottom in order to assure appropriate agitation of suspended particles. Size reduction and evacuation rates should compensate settling of coarse particles to avoid sanding of the screw. Detailed description of the tower mill and its operation have been given elsewhere (2),(3)."

Jan 1, 1989

By K. E. Waters, J. E. Nesset, F. Rosenblum, J. A. Finch, S. Moon

"Some materials when exposed to various conditions can exhibit a rise in temperature without requiring an external heat source. Generally referred to as pyrophoric or self-heating substances, they challenge the safety of materials handling, storage and transportation. Reliably assessing the self-heating potential of materials is thus essential. Over the years a number of test protocols have been developed. A widely accepted method is that recommended by the United Nations to certify the safety of shipping pyrophoric goods. Our test work on sulphide materials has shown that the U.N. test can give false negatives if the sample oxidation history is not considered. Depending on the degree of oxidation (“weathering”), the same sulphide material can exhibit self-heating ranging from safe to hazardous. For concentrates, oxidation can occur during storage and transport making the sample weathering history an important consideration in the test work. To make the U.N. test, and other single-stage self-heating procedures, more reliable in assessing self-heating potential when testing sulphide materials, it is suggested that a weathering step be incorporated in the test protocol. This test work for two sulphide samples, an ore and a concentrate, demonstrates the impact of incorporating a weathering stage in the test protocol. INTRODUCTIONSelf-heating occurs when exothermic reactions produce heat faster than can be dissipated to the surroundings. Numerous substances self-heat, ranging from wood chips and powdered milk to coal and sulphide minerals (Beever & Crowhurst, 1989; Hudak, 2002). Mixtures of sulphide minerals, most notably those containing the iron sulphide pyrrhotite (Fe(1-x)S), commonly encountered in the extraction of base metals (e.g., copper, zinc, lead, and nickel), are particularly prone to self-heating (Rosenblum, Nesset, & Spira, 2001; Payant, Rosenblum, Nesset, & Finch, 2012). In the mining and subsequent processing stages, the minerals are progressively liberated and finely ground, then separated, usually by flotation, with the resulting concentrates stored and transported to smelters for metal extraction. At most of these stages the sulphides are exposed to both moisture and oxygen, conditions that promote partial sulphide oxidation and the formation of elemental sulphur. Studies have shown that pyrrhotite, in particular, readily oxidizes to form elemental sulphur (Bernier & Li, 2003; Belzile, Chen, Cai, & Li, 2004; Somot & Finch, 2010). The elemental sulphur becomes fuel for further self-heating as the temperature of the mineral mixture increases above 100 oC (Rosenblum & Spira, 1995; Somot & Finch, 2010). It is believed the propensity of pyrrhotite to self-heat is a result of its iron-deficient, and hence somewhat unstable structure. It is worth noting that pure metal sulphides (with the exception of pyrrhotite) do not exhibit appreciable self-heating. A mixture of minerals sufficiently different in their electrochemical rest potential is required to initiate self-heating at ambient temperatures (Payant et al., 2012)."

Jan 1, 2016

By W. J. Adams

It is recognized that within life cycle assessment that the eco-toxicity potentials (TPs) derived for metals require additional research to improve their reliability. Current models used to develop TPs do not include important fate process for metals such as speciation and bioavailability. Toxicity potentials are standard values used in LCA to enable a comparison of potential toxic impacts between substances. Huijbrechts (2001) calculated toxicity potentials for 181 substances utilizing the USES model for six impact categories, i.e. freshwater aquatic ecotoxicity, marine aquatic ecotoxicity, freshwater sediment ecotoxicity, marine sediment ecotoxicity, terrestrial ecotoxicity and human toxicity (not considered here). Marine ecotox potential for metals is typically high using this approach, whereas most open ocean metal concentrations are very low. A sensitivity analysis of the USES-LCA model was undertaken using copper as an example. Results indicate: fate processes on the global scale are driving the marine water and sediment TPs for copper most; the second most important fate parameter is sedimentation from the water and burial in deep sediment layers; inclusion of speciation and bio-availability processes would be very beneficial; more accurate estimates of input parameters should be used, and the PNECwater and PNECsediment and all partition coefficients for metals should be updated in the model.

Jan 1, 2007

By G. Lyle

Since its inception CEMI (Centre for Excellence in Mining Innovation) has focused on facilitating innovative solutions to the mining industry in six strategic research areas; GeoRisk, ConstructMine, ValueMine, FindMine, SustainMine and MineTech (visit www.miningexcellence.ca for details). This paper focuses on CEMI?s largest project to date, Ventilation on Demand (VOD). Energy consumption in mines can account for upwards of 40% of a mines operating cost, with a significant portion of this been consumed by the ventilation requirements. VOD provides a significant opportunity to reduce overall mine ventilation requirements and subsequently energy costs, while potentially increasing mine productivity. CEMI is currently in year 2 of an assessment of VOD, focusing on the financial, physical and equipment viability of utilizing such systems in both new and existing mines. This two year program, to be completed by March 31, 2011, is designed to systematically assess such a system to determine if and when it could effectively be applied in underground mines. The paper will describe the process by which the project was initiated, the demonstration projects established to capture data, the means to interpret the data and the modelling developed to calibrate and predict ventilation system requirements.

Oct 1, 2010

By William D. Gallant, Thomas M. Barczak, Carol Tasillo

"This paper describes the results of full-scale testing of several multi-layered wood crib configurations that were tested in the Bureau of Mines mine roof simulator in cooperation with the Cape Breton Coal Research Laboratory and Cape Breton Development Corporation of Sydney, Nova Scotia. Nine different crib configurations currently being used as wood packwall supports for advancing longwall applications in Canada were evaluated. Configuration parameters understudy included the aspect ratio (height-to-width relationship) and percentage of solid material used in the crib construction. Test results and generalized wood crib behaviour are discussed in detail. Recommendations are made concerning crib constructions to maximize strength and stability. A cost benefit analysis of multi-layered wood crib configurations is made. A comparison of laboratory results and underground observations of several wood packwall supports in the Sydney coalfield suggest in situ load capacity is less than that measured in laboratory testing. Reasons for the apparent decrease of in situ load bearing capability are described.IntroductionA cooperative effort was undertaken by the U.S. Bureau of Mines with the Cape Breton Development Corporation (CBDC) and the Cape Breton Coal Research Laboratory (CBCRL) to evaluate the behaviour of gateside packing materials used in advancing longwall mining applications in the Sydney coalfield. As part of this effort, full-scale tests were conducted on wood packwall supports in the Bureau's 3-million pound (13.3 MN) active load frame.Nine different pack configurations were evaluated as part of this study. The wood packwall supports were multi-layered crib constructions from 6 in. (0.15 m) by 6 in. (0.15 m) cross section timbers using timber s 30 in. (0.75 m) and 60 in. (1.5 m) in length . The percentage of solid material in the crib constructions varied as illustrated in Figures 1 and 2. A summary of crib constructions is provided in Table 1."

Jan 1, 1991

By J. W. Gregg, P. M. Dranchuk, D. L. Flock

"From preliminary investigations it has been observed that although evaporation losses may be estimated by comparing single values of certain physical properties of crude oils and their evaporation residues, such techniques possess little accuracy unless both the evaporation process and the variation of the property as a function of the process are completely known. The accuracy of estimation may be increased somewhat through the comparison of property mid-per-cent curves. Further increases in accuracy are possible if bottoms yield •curves rather than mid-percent curves are used. The use of both the mid-percent and bottoms yield curves however involves a prohibitive amount of effort in most cases. Examinations of distillation bottoms from Hempel type distillations carried to end points just short of the cracking point have indicated that these bottoms are not appreciably affected by the evaporation process. It was further observed that bottoms of identical API gravity, obtained from a crude oil and its evaporation residues behave as if they were pure components which were unaffected by evaporation. Based on these observations Hempel distillation bottoms of equal API gravity were obtained for a crude oil and its various evaporation residues from API gravity bottoms yield curves. The volume percent of these bottoms in the crude oil and its residues were used to calculate the evaporation losses suffered by the crude in order to yield the various residues. The results indicate that, although further refinements in technique are required, it is possible to calculate evaporation losses with an accept-able degree of accuracy through the use of this method."

Jan 1, 1960

By CRO CRO

Elk Valley Coal?s Cheviot Project is located in the Alberta foothills south of the town of Hinton. The mine has been in operation now for the 3 years. The start up and subsequent operation of the Cheviot project has been directly influenced by the Cardinal River Mine. As the Cardinal River Mine was winding down due to reserve depletion in 2004, the price of seaborne traded metallurgical coal jumped to record levels and customers began aggressively seeking new sources of supply. Several months later, the owners of Elk Valley Coal decided to begin mining at the Cheviot mining area, extending the life of the area?s operations by over 25 years. The Cheviot Project had been delayed by low coal prices, ownership changes and a complicated and lengthy regulatory process fueled in large measure by stiff opposition from a number of major environmental organizations. Chief to the startup of the project was the construction of a 23-kilometer-long haul road that would connect the new coal measures to the existing Cardinal River processing and rail facilities. Construction of this road was completed with the first coal truck making its first trip in October 2004. This paper will look at some of original assumptions, the actual mining experiences and the lessons that were learned while moving from the drawing board to the current development as it exists today.

May 1, 2007

By Ray Collier

MINING TODAY l EXTENSIVE AND EXPENSIVE PERMITTING PROCESSES WITH UNKNOWN RESULTS l GENERAL AND IMPASSIONED RESISTANCE TO RESOURCE BASED INDUSTRY l SOPHISTICATED, ORGANISED, AND WELL FUNDED OPPOSITION l MOST LOCAL GOVERNMENT DOESN?T WANT MINING TODAY?S TALK l FOUR SPECIFIC OPERATIONS ON WHICH OUR EXPERIENCE IS BASED ? SECHELT ? CADMAN ? GRANVILLE ISLAND ? LEHIGH CEMENT DELTA PLANT l OUR APPROACH TO COMMUNITY RELATIONS

May 1, 2002

By Wayne D. Goodfellow, William M. Luff, Steven J. Juras

Abstract-Brunswick No. 12 is a vent-proximal massive sulfide deposit that formed above a feeder pipe with associated hydrothermal alteration. Because of the replacement of bedded sulfides deposited above the hydrothermal vent, individual sulfide lenses show the following vertical and lateral zoning outward from the vent complex: massive pyrite-pyrrhotite-chalcopyrite core - interlayered pyrite-sphalerite-galena (Pb-Zn ore zone) - bedded pyrite. The feeder zone which underlies the Cu-rich core consists of an anastomosing network of pyrite-pyrrhotite-chalcopyrite­ quartz veins with variable and generally minor contents of ferroan carbonate, Fe-rich chlorite, sphalerite, galena and arsenopyrite. Hydrothermal alteration of felsic igneous rocks hosting and adjacent to the feeder pipe is represented by an inner zone (zone 1) characterized by sulfide stringers, Fe-rich chlorite, muscovite, quartz, and ferroan carbonate that formed at the expense of feldspars and what was probably glass; outer zones (Il and III) are represented by Mg-rich chlorite and muscovite formation, and the albitization and silicification of K-feldspar. Accompanying these alteration trends is a marked decrease of Na + Ca, and an increase in Fe + Mg + C03 in zone 1, and increases in Mg + Na in the outer zones. The classic zoning of metals within the sulfide lenses, the formation of a feeder pipe below the vent-proximal sulfide core, and the hydrothermal alteration of felsic volcanic rocks cut by the feeder pipe all support a vent-proximal origin for the Brunswick No. 12 deposit. Furthermore, restriction of sulfide stringer mineralization to the footwall sequence, the folding of the stringer zone by an F1 fold, and the difficulty of long distance mass transfer of metals from the sulfides into the host rocks all argue against a tectonic origin for the stringer zone. All of the evidence indicates that the feeder pipe formed during the ore forming hydrothermal event, but has been distorted and in some areas detached from the overlying massive sulfides during subsequent deformation.

Jan 1, 1992

By Wayne D. Goodfellow, William M. Luff, Steven J. Juras

Brunswick No. 12 is a vent-proximal massive sulfide deposit that formed above a feeder pipe with associated hydrothermal alteration. Because of the replacement of bedded sulfides deposited above the hydrothermal vent, individual sulfide lenses show the following vertical and lateral zoning outward from the vent complex: massive pyrite-pyrrhotite-ehalcopyrite core interlayered pyrite-sphalerite-galena (pb-Zn ore zone) - bedded pyrite. The feeder zone which underlies the Cu-rich core consists of an anastomosing network of pyrite-pyrrhotite-chalcopyritequartz veins with variable and generally minor contents of ferroan carbonate, Fe-rich chlorite, sphalerite, galena and arsenopyrite. Hydrothermal alteration of felsic igneous rocks hosting and adjacent to the feeder pipe is represented by an inner zone (zone I) characterized by sulfide stringers, Fe-rich chlorite, muscovite, quartz, and ferroan carbonate that formed at the expense of feldspars and what was probably glass; outer zones (II and III) are represented by Mg-rich chlorite and muscovite formation, and the albitization and silicification of K-feldspar. Accompanying these alteration trends is a marked decrease of Na + Ca, and an increase in Fe + Mg + C03 in zone I, and increases in Mg + Na in the outer zones. The classic zoning of metals within the sulfide lenses, the formation of a feeder pipe below the vent-proximal sulfide core, and the hydrothermal alteration of felsic volcanic rocks cut by the feeder pipe all support a vent-proximal origin for the Brunswick No. 12 deposit. Furthermore, restriction of sulfide stringer mineralization to the footwall sequence, the folding of the stringer zone by an F, fold, and the difficulty of long distance mass transfer of metals from the sulfides into the host rocks all argue against a tectonic origin for the stringer zone. All of the evidence indicates that the feeder pipe formed during the ore forming hydrothermal event, but has been distorted and in some areas detached from the overlying massive sulfides during subsequent deformation.

Jan 1, 1992

By P. A. Hacquebard, M. P. Avery

"Gondwana coal deposits are widespread and are known to occur in four continents. They are present in Brazil, India, South Africa, and Australia. From coal petrographic examinations and a detailed literature survey, it is interpreted that Gondwana coals are present also in Canada and the United States. Laurasia, or Northern Hemisphere, coals occur in the United States, Canada, and Europe. They form the main coal producing fields of the world. Megascopically, Gondwana coals have a uniform, micro-banded appearance, with a dull lustre; Laurasian coals are bright and have distinct bands of vitrain and clarain. Petrographically, Gondwana coals, compared to Laurasian coals, are lower in vitrinite, but higher in inertinite, particularly in semifusinite. Mineral matter averages 16% in Gondwana coals and 5.7% in Northern Hemisphere coals.Gondwana coals are characterized by thick seams that terminate through lithification (Versteinerung), whereby coal passes laterally into shale. Laurasian coal seams are thinner and terminate by splitting and digitation.Vitrinite/inertinite ratio data indicate deposition of the Gondwana coals in dry marshes under strong oxidizing conditions. The Laurasian coals originated in wet marshes in a reducing environment. As deduced from fossil plants and fossil spores, temperate and near arctic conditions apply for the Gondwana coals. A tropical and subtropical climate is indicated for the Laurasian deposits. The Gondwana coals were formed under allochthonous conditions. They derived from vegetation that drifted into the peat bogs. The Laurasian coals are autochthonous and originated from vegetation that grew and was buried in the peat bogs. The Gondwana coals are Late Carboniferous and Early Permian. The Laurasian coals are entirely Late Carboniferous."

Jan 1, 2004

By C. Taschereau, G. A. Vickell, A. R. Laplante

Evidence in support of an iron-gold corrosion cell during the high-temperature/highpressure elution of loaded carbon is presented herein including, but not limited to, its discovery, mode of genesis, and confirmatory laboratory testwork. A discussion of metallurgical and economic impacts, remedial investigations, plant design considerations, and future work including mitigative possibilities is presented.

Jan 1, 2006