Search Documents

By K C. Corin, N Ndamase, M Tadie

Mining operations in arid regions are compelled to reduce their consumption of fresh water. Closed water circuits are an attractive solution and, in addition to reducing freshwater consumption, have the added benefit of reducing reagent consumption as well as the environmental impact by eliminating effluent discharge. Accumulating ionic species have been shown to hinder collector adsorption which reduces the recovery of valuable minerals. Numerous studies have investigated the effect of degrading water quality on collector adsorption however there is very limited understanding as to how this takes place from an electrochemical perspective. This study therefore aims to investigate how the presence of accumulating ionic species at varying concentrations affects the electrochemical adsorption of sodium ethyl xanthate onto galena. The synthetic plant water used in this study comprised of single salt solutions to isolate the effects of the ionic species of interest. The ionic strengths were varied between 0.0242 M, 0.0727 M, 0.1212 M and 0.2426 M which correspond to University of Cape Town (UCT) Centre for Minerals Research (CMR) synthetic plant waters of 1, 3, 5 and 10SPW, respectively. Mineral rest potentials indicated how changing water quality affected xanthate-mineral interactions. Microflotation observed the impact of changing water quality on mineral floatability.

Aug 24, 2022

By S Mitra, D O’Dea, N Barrett, T Honeyands, E Copland

This work describes a novel mapping technique that allows the direct overlay of calculated local phase equilibria on micrographs of the physical system. The technique demonstrated integrates FactSage™, ver 8.2 (by Thermfact Ltd. and GTT-Technologies) phase equilibria calculations with mapped compositions determined by Scanning Electron Microscope – Energy Dispersive X-ray Spectroscopy (SEM-EDS) to visually express calculated properties while preserving the spatial information of the sample. The developed methodology is used to analyse interrupted blast furnace softening and melting tests containing mixed burdens of lump and sinter. Tests are interrupted at 1300C and cooled to room temperature for analysis. Phases present at room temperature are analysed to infer the liquid fraction and phases present at high temperature. Analysis of the interface regions between the dissimilar burdens allows insights to be gained into the interaction mechanism. During the transition from solid to liquid, migration and interaction of liquid oxide across the interfaces of the dissimilar burdens has been observed and demonstrated to impact softening and melting performance. Specifically, interaction of the oxides generated by lump (primarily FeO, SiO2 and Al2O3) and sinter (primarily FeO, CaO, SiO2, Al2O3 and MgO) are analysed, and the occurrence of a range of new mineral phases such as merwinite, melilite, olivine and bredigite observed.

Jun 19, 2024

By J H. Park, R R. Kim, H S. Park, H J. Kim

This study focuses on the recovery of valuable metals, specifically silver (Ag) and palladium (Pd), from copper-containing sludge (with copper content less than 20 per cent) generated during PCB processing and from spent petrochemical catalysts used in vapour decomposition during oil refining processes. The present results indicate that an increase in the mixing ratio of alumina-based spent catalyst leads to a decrease in the recovery rate of Ag and Pd. The recovery rates for Ag and Pd range from 84 per cent to 96 per cent and 80 per cent to 98 per cent, respectively. This trend is attributed to the increased emulsification of copper droplets containing Ag and Pd in the slag. The emulsification is caused by the decrease in the settling velocity of the copper droplets due to the increased viscosity of the slag as well as by the decrease in the slag-metal interfacial tension due to an increase in sulfur content at higher mixing ratio of spent catalyst.

Jun 19, 2024

By R A. Anand, N N. Viswanathan, M M. Pande

Slags are the most voluminous solid by-products generated in pyrometallurgical operations, and, as such, finding an application for these oxidic materials is pertinent to maintaining resource efficiency. In particular, pyrometallurgical copper production is associated with high slag rates, typically ranging from 2.2 to 3.0 tons of slag per ton produced copper, which necessitates slag valourisation. A possible application for these iron silicate slags is as supplementary cementitious materials (SCMs), which effectively lowers the CO2 emissions per ton of cementitious material. Although utilising iron silicate slags as SCMs has been studied in previous work, the scientific literature has limited data on the effect of composition on the inherent reactivity in cementitious systems. More specifically, no reports on the impact of FeO/SiO2 ratio have been presented in previous publications. Therefore, the present study aimed to isolate this parameter in a synthetic FeO-SiO2-Al2O3-CaO-MgO-Cr2O3 system. Since the amorphous content is a pertinent parameter for SCMs, a high-temperature confocal laser scanning microscope (HT-CLSM) was utilised to assess the crystallisation behaviour at continuous cooling conditions. Furthermore, high-temperature rheological experiments were conducted to measure the viscosities of the slags in relation to the crystallisation behaviour. The experiments showed that depolymerising the slag by increasing the FeO/SiO2 ratio generated a less viscous slag, which showed higher tendencies for crystallisation. Furthermore, experiments assessing the inherent reactivity as an SCM showed that depolymerising the slag by increasing the FeO/SiO2 ratio as the sole independent parameter generated an initially more reactive slag. However, replacing SiO2 with FeO was found to negatively affect the reactivity as measured over seven days within the tested compositional range.

Jun 19, 2024

By K T. Mandisodza, T J. Cartledge

The principal objective of Geotechnical Engineers supporting operating mines is to provide safe working conditions and ensure that pit designs are geotechnically optimised to site conditions and pre-defined stability requirements. Pit slope designs are delivered in advance of pit excavations. Making changes to these designs is usually slow to enact and involves a layered sign-off before implementation, leading to unwanted delays in their adoption and subsequently increased production pressures. When unexpected ground conditions are encountered during the mining process, or short-term mining schedule requirements demand it, changes to these designs may not be easily feasible in certain situations. It is when these scenarios arise that Geotechnical Engineers need to be proactive and consider unconventional options to deliver safe operating conditions while satisfying short-term requirements to the mine schedule. Essentially, the geotechnical short-term strategic designs double-pronged approach supports the mine schedule while providing safe conditions and minimising geotechnical risks for people and equipment. Common short-term strategic geotechnical designs include; slope buttressing, over-steepening cut slopes to increase reserve recovery through unplanned or emergency cutbacks, and accepting risk threat and operating under unstable slopes. When implementing strategic design options, the Geotechnical Engineer must consider the broader implications for such designs. They must think of the plan’s long-term effects on the mine schedule and pit wall stability. Initiating aggressive designs to recover additional reserves to satisfy a short-term scheduling demand could result in-pit wall instability or suboptimal pit layout. Before and during the implementation phase, the Geotechnical Engineer must communicate and engage with relevant stakeholders to ensure that the plan is executed accordingly and geotechnical risks are effectively managed. Proactiveness to ground response and implementation of risk management strategies will improve safety performance and optimise mining schedules.

Jun 22, 2022

By Y Chung, B Choi, H Lee

Numerous studies have explored refractory corrosion in the presence of slag and/or metal, utilising the Finger Rotating Test (FRT). Recent experimental results revealed that corrosion initially increased with rising rotation velocity but was then suppressed above a critical rotating speed, under conditions involving a two-liquid solution of slag and molten steel. This phenomenon indicated that the liquid/liquid interface movement occurred during spindle rotor. However, understanding of the phenomenon, known as the rod climbing effect, remains inadequate in the case involving slag, molten steel and refractories. To gain deeper insights, a simulation experiment was conducted on the phenomenon using silicon oil/water and the phenomenon was analysed using computerised simulation software (Ansys Fluent). Experimental modelling demonstrated that interfacial movement occurs even at low rotation velocity, as low as 200 rev/min, when the viscosity of silicone oil is at 100 cP. Computational analysis utilising the Volume of Fluid (VOF) method and a realisable k-ε turbulence model elucidated that interface elevation during rotor rotation arises due to viscosity disparities between the two fluids. Furthermore, this movement is more pronounced when the viscosity difference is lower. Additionally, the study findings suggest that higher density differences between two liquids suppress the phenomenon of interface movement.

Jun 19, 2024

By B Laidens, D Souza, W Bielefeldt

The CaO-MgO-SiO2-Al2O3 system, characterised by its intricate phases and thermodynamic properties, plays a pivotal role in steel secondary refining processes, encompassing desulfurisation, non-metallic inclusion capture, and refractory protection. Accurate predictions for diverse industrial applications, including metallurgy, ceramics, and materials science, are imperative. To address this challenge, a combination of machine learning techniques will be specifically applied to model the liquid fraction of the slag and the solid fraction of MgO. The development of an artificial intelligence (AI) system, leveraging various machine learning techniques, has gained momentum in this project. The focus of this work is on constructing an AI model, based on machine learning techniques, within the CaO-MgO-SiO2-Al2O3 system, utilising simulation results from FactSage™, version 8.1 (by GTT Technologies). The primary objective is to train the AI model using these simulation outputs to predict the percentage of liquid fraction and MgO saturation based on chemical composition parameters. The AI model will undergo training with a comprehensive data set of simulations within the CaOMgO- SiO2-Al2O3 system, covering a diverse range of compositional at 1873 K. These simulations, conducted through FactSage™ 8.1 software, provide a robust foundation for AI model training, ensuring generalisability and precise predictions for the liquid fraction of the slag and the solid fraction of MgO, the solid fraction of MgO in this case is determined by the difference between the total MgO and the MgO in the liquid fraction, so it is not the objective of this study to determine which phase of MgO is in the solid state.. The predictive capabilities of this AI model hold significant implications for process optimisation, quality control, and decision-making in CaO-MgO-SiO2-Al2O3- dependent industries. Precise estimations of the liquid fraction and MgO saturation empower researchers and engineers to enhance operational efficiency and quality. This paper explores the methodologies employed for AI model creation and training, achieved results in terms of prediction accuracy, and potential applications in the field. The development of this AI system signifies a notable advancement in utilising machine learning for better comprehension and control of complex chemical systems. Furthermore, to align the study with real-world steel production, we introduce FeO and MnO at concentrations of 2 per cent and 1 per cent at 1873 K, respectively, following the validation of model results using the CaO-MgO-SiO2-Al2O3 system. This adjustment aims to bring the study closer to the observed reality in steel mills globally.

Jun 19, 2024

By X Ling, M Barati, E Moosavi-Khoonsari

In the pyrometallurgical process of secondary lead recycling, a desulfurising agent, such as Na2CO3 is added to minimise the emissions of sulfur into the atmosphere, while silica is introduced into the smelter as a fluxing material. Subsequently, a significant amount of Na2O and SiO2 remains in the downstream reverberatory furnace and blast furnace slags. However, there is limited understanding of the thermodynamic behaviour of silicate-based lead slags rich in Na2O, posing challenges in accurately determining the optimal condition for targeted metal recovery and final slag composition. In this work, the equilibrium phase relations of the PbO-Na2O-SiO2 system in the primary phase field of Na2SiO3 are studied from 800 to 1000°C via equilibration-quenching method. Samples with different compositions were prepared and held in platinum capsules in air at these temperatures to reach equilibrium. The equilibrated samples were subsequently quenched and the phase compositions were measured by electron probe microanalysis (EPMA). The results were then compared to those of previous studies and any discrepancies were resolved.

Jun 19, 2024

By K Haga, G Danha, A Shibayama, L L. Godirilwe

The hydrometallurgical separation and enrichment processes provide an effective way to selectively recover metals from relatively dilute multicomponent sulfuric acid leach solutions. The multicomponent leach solution utilised in this study contained 0.3 g/L Cu, 0.34 g/L Ni, 0.13 g/L Co, and 2.96 g/L Fe, which was obtained after high-pressure oxidative acid leaching (HPOAL) of the copper-nickel smelter slag. The solvent extraction (SX), precipitation, and xanthate complexation processes were employed to recover and upgrade Cu, Ni, and Co from the leach solution. Batch SX tests were carried out using a countercurrent two-stage mixer settler extraction column, and LIX 984N (10 per cent v/v) as a copper extractant. Fundamental parameters influencing the extraction process such as pH, mixing speed, H2SO4 concentration, and organic/aqueous (O/A) phase ratio were investigated. For copper enrichment in solution, a combination of two extraction stages and two stripping stages were employed. Copper was successively separated from Fe, Ni, and Co under optimised extraction conditions (pH 2, 400 rev/min, O/A 0.25, and 20 min contacting) and stripping conditions (175 g/L H2SO4, 400 rev/min, O/A 4, and 20 min contacting). About 97 per cent of copper was extracted with low co-extraction of Fe, Ni, and Co of about 5.90 per cent, 1.47 per cent, and 2.53 per cent, correspondingly. A final Cu-rich solution containing 23 g/L Cu was obtained with a very low Fe concentration of 0.05 g/L. Additionally, for iron removal from the Ni/Co raffinate solution, more than 99 per cent of iron was precipitated at pH 4 by the addition of a calcium carbonate (CaCO3) suspension, with low co-precipitation of nickel and cobalt of around 3.68 per cent and 2.27 per cent, respectively. Furthermore, about 83.6 per cent of nickel and 99.4 per cent cobalt were co-precipitated from the solution by potassium amyl xanthate (PAX) solution at pH 6. The Ni and Co xanthate complexes were thermally decomposed and recovered as cobalt oxide (CoO) and nickel sulfide (NiS) solids.

Aug 24, 2022

By S Maritsa, E K. Chiwandika, S M. Masuka

The iron and steel industry is experiencing an increase in the use of iron and steel commodities within societies, decarbonisation pressures, depletion of high iron ore grades and high energy consumption. This necessitates scrap metal recycling, low-grade ore utilisation using the induction or electric arc furnace to achieve the global target of net zero CO2 emission. The available highquality scrap metal cannot sustain the steel industry but the world has unused hematite-goethite ores. It is the aim of this research that this resource be utilised using the induction furnace to sustain the steel industry in an environmentally friendly manner. Indurated pellets prepared from the hematite-goethite ore, 5 wt per cent limestone and 5 wt per cent coal addition were smelted in the induction furnace at 1350 ± 50°C with 25 mins holding time. The effects of basicity and carbon content were also investigated to optimise the smelting parameters. The results showed that the careful control of the basicity, and iron-to-carbon ratio maximised total metal recovery. The optimal basicity ratio was determined to be 1.3 and a carbon to iron ratio of 1.4 achieved a total metal recovery of 73 per cent. The metal recovery was closely related to the estimated slag melting temperature. The basicity ratio of 1.3 achieved the lowest slag melting temperature estimated to be around 1380°C based on the CaO-SiO2-Al2O3 phase diagram. The recovered metal had a comparable chemical composition and microstructure to that products from an ITmk3 furnace.

Jun 19, 2024

By M Bouare, C Holland, K N’Diaye

Two adjacent open pits in Mali hosted by deeply weathered saprolitic materials were mined consecutively over the course of approximately 12 months. During excavation, both pits experienced significant displacement and tension cracking as the result of deeper than expected depth of weathering coupled with relatively steep slope angles and significant groundwater. In response, geotechnical and operations teams overcame numerous monitoring challenges with prisms and radar to develop a simple and effective monitoring system coupled to a Trigger Action Response Plan (TARP) which enabled continued safe operations while reducing ore loss. Observations of previous slope performance of these two pits allowed for greater confidence in empirical failure runout calculations that was used to specify the standoff widths for the exclusion zones in the pit. Back analysis of the slope as-built performance after the first indications of slope distress was also conducted. The back analysis was used to confirm rock mass parameters for modelling while being utilised as a reality check for the stability analysis. The stability analysis indicated that leaving a large step-out or buttress would not prevent the displacement, resulting in some ore being sacrificed to ensure the safety of personnel. Key learnings from this experience highlight the importance of: • up-to-date geological interpretation of the depth of weathering • ensuring slope design guidance is reviewed and updated as latest information (ie geology and monitoring) is received • having multiple complementary slope monitoring methods to ensure redundancy • ensuring visual observations and as-built performance are utilised as a reality check to provide greater confidence in stability analysis and design guidance.

Jun 22, 2022

By J Nell, J Petersen, X C. Goso

The feasibility of increasing the deportment of titanium species and the stability of the pseudobrookite solid solution (M3O5) in a titaniferous slag was investigated, to facilitate the valourisation of titaniferous slags. Thermochemical simulations using FactSage™ software, ver 8.3 (by Thermofact/CRTC and GTT-Technologies), and equilibration-quench experiments were conducted using an appropriate synthetic titaniferous slag composition in an oxygen partial pressure (pO2) ranging from air to 10-16 atm under non-isothermal conditions. The temperature-pressure phase stability diagram for the synthetic slag containing 37.19 per cent TiO2, 19.69 per cent SiO2, 13.12 per cent Al2O3, 16.00 per cent CaO and 14.00 per cent MgO showed that the spinel solid solution (M3O4) was the primary phase until a pO2 of 10-10.5 atm, thereafter M3O5 was the primary phase until a pO2 10-13.2 atm. M3O4 again was the primary phase between a pO2 10-13.2 and 10-16 atm. The changeover of the primary phase coincided with an increase in the liquidus surface. When cooling the slag in a pO2 of 10-16 atm, M3O5 crystallised as a ternary phase that showed a rapid increase in mass while that of the primary M3O4 phase decreased and that of the secondary perovskite (CaTiO3) phase increased at a slower rate. At 1300°C under sub-liquidus conditions, the contents of M3O5, M3O4 and CaTiO3 were about 20 per cent, 15 per cent, and 11 per cent, respectively. Experimental results showed that the Ti3+/Ti4+ mass ratio in the M3O5 phase, ie a measure of the reduction of titanium species, is not considerably sensitive to equilibration temperature in the reviewed range. Slow cooling and minimum/no oxidation during cooling of titaniferous slag would increase the deportment of titanium species to, and the growth and stability of the M3O5 phase.

Jun 19, 2024

By H Kim, J Park, J Lee

Silico-ferrite of calcium and aluminium (SFCA) is a bonding phase in the iron ore sinter. The phase transition upon melting of SFCA was investigated with Differential Scanning Calorimetry and Confocal Laser Scanning Microscope. The initial melting of SFCA occurred at 1183.2°C and a massive melting was found at around 1351.1–1358.2°C. A phase transition-melting was investigated at 1476.5–1478.7°C. The liquid phase was composed of immiscible phases. The present results would be utilised to design a new iron ore sinter for better processing performance in a hydrogenenriched ironmaking process.

Jun 19, 2024

By J Furtney, W Fu, D Nutakor, A Brose

Rock blasting outcomes are often a shared responsibility of both the mine operations group and the mine geotechnical group. From an operational logistics and planning perspective, blasting concerns include optimal fragmentation for subsequent crushing, ensuring the blast is energetic enough to allow easy digging, and understanding the effect of muck from a previous blast on the current blast. From a geotechnical perspective, wall damage and catch bench capacity are the primary concerns. Other concerns for both teams include damage to mine infrastructure by fly rock or blast-induced vibrations, and the stability of open stopes under the pit. This work presents two blast modelling applications (or ‘apps’). The basic app instantly gives fragmentation and wall damage predictions for a given generic blast design. The advanced app loads the current pit contours, reads the blast design from a spreadsheet, and calculates the expected vibration magnitude and peak frequency. The apps have been developed specifically for the Rio Tinto Borates and Lithium Mine in California and are used to support blast design between the operations group and geotechnical group. The basic app instantly gives fragmentation and vibration predictions given a blast design by combining the Kuz-Ram fragmentation model with the scaled distance model for vibrations. The advanced app uses the signature hole method. Blasting outcomes at the mine have improved since using the apps.

Jun 22, 2022

By N Gruber

In the continuous casting of ultralow carbon (ULC) steels, free carbon is used to control the melting behaviour of mould powders. If the carbon is not completely removed during melting, it is enriched at the top of the slag pool. Liquid steel may come into contact with this layer because of the turbulence of the molten metal, resulting in its recarburisation, which negatively affects the desired product quality. Thus, a reduction in carbon input is desirable. For this purpose, SiC and/or Si3N4 with and without antioxidants were selected as melt-control additives to replace carbon in the mould powders. Thermodynamic calculations were performed to quantify their effect on the melting behaviour based on the chemical composition of a flux already applied to ULC steels. To experimentally assess the liquefaction behaviour, laboratory mould powders were prepared and annealed in steel crucibles closed with a lid. Crucibles were inserted into a furnace that was already preheated to selected temperatures between 900–1200°C for 10 mins and quenched to room temperature. Subsequently, the samples were mineralogically investigated. The results confirmed those obtained from the thermodynamic calculations. Si3N4, and SiC in particular, are suitable raw materials for delaying the solid-solid reactions of raw material components during melting. Owing to their stability at high temperatures, the necessary SiO2 content to form a liquid phase is not available, resulting in lower amounts of the liquid phase. The addition of antioxidants to delay the oxidation of SiC further reduces this positive effect. Attempts to decrease the SiC content without negatively affecting the melting behaviour resulted in a reduction in the CO2 emission by at least 27 g CO2/kg of mould powder when compared to the carbon-containing standard mould powder. These investigations revealed differences in the melting behaviours of granules and loose powders, which are related to their respective production processes.

Jun 19, 2024

By S Lee, I Sohn

The ferrous and non-ferrous metallurgical industries have been utilising slags, fluxes and mattes for process optimisation and quality improvements at high temperatures. Understanding the fundamentals of the thermodynamics and kinetics of chemical metallurgy regarding slags, fluxes and mattes has been essential to the technological developments of these optimisation and improvements. This work will discuss how these fundamentals have been studied in the reactions involved and implemented in the ferrous industry from primary refining to continuous casting. In particular, the chemical driving forces that allow these reactions to take place and the limitations of the kinetics that require optimisation to enhance the reactions. In addition, the future research direction for slag technology innovation and the role of these fundamentals will also be described.

Jun 19, 2024

By P Cherepanskiy, G Elphick, R Hus, C Perring

When an iron orebody nears its end of life, the extracted material can become increasingly problematic to handle. Higher moisture content occurs as larger portions of originally-below-water-table material is mined, which in some deposits is accompanied by further changes in physical and/or chemical properties present along the edges of the orebody. Plant delays related to problematic material have affected all of BHP’s mining hubs to various degrees. Following the recent successful work in Yandi, where the development of an index to quantify the handleability of channel iron ore deposits resulted in an increase in extracted volumes and an extension to the expected life-of-mine, the value of implementing similar indices for bedrock iron ore deposits has been recognised. A materials handling index has been developed by combining observed empirical relationships between material properties and processing plant performance. Indices for each deposit were further refined and optimised by implementing a back-testing strategy which facilitated an understanding of what weighting or scaling each of the contributing components should carry to yield the highest success rate of predicting actual delays at a given plant. Currently materials handling indices are deployed to all mine sites and are made available in block models as well as calculated for individual blasthole and production samples. Values in block models are obtained by predicting the required properties using machine learning models, whereas hyperspectral data is used to ‘measure’ some of those properties on a sample level. This paper discusses the work that has been undertaken to obtain materials handling indices, the testing that has been done to optimise them, and what processes have been developed to ensure the best metrics are being used in the different planning and scheduling horizons to optimise extraction.

Jun 22, 2022

By M Saghaeian, M Zare, V Sheikhzadeh, R Hejazi

High-Pressure Grinding Roll (HPGR) is one of the efficient methods for increasing the specific surface area (SSA) of iron ore concentrate for pellet feed production. HPGR grinding mechanism implies that material should compressed between the two rolls, therefore layer of material must be able to resist required pressure for achieving suitable grinding conditions. In this study, by doing SSA increasing tests with pilot HPGR, the effects of silica reduction on SSA increasing results were investigated. For this purpose, HPGR tests were performed on an Iranian magnetite concentrate before and after reverse flotation silica reduction tests. Based on the laboratory test results, silicates have been concentrated in two fraction sizes of the sample comprises coarser than 150 microns in form of quartz and finer than 7 microns in form of iron silicates. These silicates have been effected on reduction of concentrate bed pressure resistance by creating a pasty and sticky mud. In this condition, HPGR cannot work properly and operation results are not acceptable. According to flotation silica reduction tests, with 90 per cent weight recovery, concentrate Fe grade is increased from 67.8 per cent to 69.5 per cent and SiO2 content is reduced from 1.98 per cent to 0.9 per cent and especially for lower than 7 microns fraction size, as a critical fraction, SiO2 content decreased from 4.45 per cent to 2.35 per cent. HPGR tests were performed on 8 per cent moisture in 4 N/mm2 specific force and according to the results after silica reduction HPGR operation conditions are optimised. Results showed that the working gap increased from 7 to 10.5 mm and specific throughput of material raised from 180 ts/hm3 to 250 ts/hm3 , and SSA increased by 300 cm2 /gr in a single pass.

Aug 24, 2022

By S van der Sluijs, M van Ende, Y Tang, A Emami

This paper presents a phenomena-based model for investigating the possibility of scrap melting in an Open Slag Bath Furnace (OSBF) for green ironmaking. The goal of this study is to enhance the circularity of the steelmaking process by utilising scrap as a green source of iron in OSBFs. The model takes into account the fundamental differences between OSBFs and traditional processes such as Electric Arc Furnaces (EAFs) and Basic Oxygen Furnaces (BOFs). The model considers three primary regions where scrap heating and melting occur: the solid feed pile, slag and hot metal. It accounts for factors such as the furnace geometry, scrap charging mechanism and specific heat and mass transfer properties of the reactor. The model was validated using literature data and was used to investigate the heating and melting behaviour of individual scrap particles under various process parameters. The study finds that the scrap melting process in OSBFs involves three stages: shell formation, shell remelting and subsequent melting of the parent scrap. The carbon content of the scrap and the liquid hot metal plays a critical role in determining the melting behaviour. Depending on the carbon concentration and temperature, the melting process can be heat transfer controlled or mass transfer controlled. The paper also examines the scrap feeding methods in OSBFs, including direct charging into the slag or charging through a feed pile. The model provides insights into the melting rate of scrap compared to Direct Reduced Iron (DRI) in OSBFs and highlights the role of carbon in this process. Overall, this phenomena-based model contributes to the understanding of scrap melting behaviour in OSBFs and provides valuable insights for optimising the circularity and efficiency of green ironmaking processes. The findings of this study can inform the design and operation of OSBFs, paving the way for increased utilisation of scrap as a sustainable feedstock in the steel industry.

Jun 19, 2024

By J Bang, I-H Jung

Ti is an important constituent for steels and superalloys. During the continuous casting process and ElectroSlag Remelting process (ESR), Ti in molten steel and superalloy can have chemical reactions with casting flux and ESR slag containing CaO and CaF2. In order to investigate such exchange reactions, the understanding of the (Ca,Ti//O,F) reciprocal slag system is prerequisite. In the present study, a coupled phase diagram experiment and thermodynamic modelling of the (Ca,Ti//O,F) reciprocal system was performed. In particular, the phase diagram of the CaF2-TiO2 system was experimentally investigated by Differential Thermal Analysis (DTA) experiment and quenching experiments followed by Electron Probe MicroAnalysis (EPMA) phase analysis. The Gibbs energy functions of all solid and liquid phases in the (Ca,Ti//O,F) reciprocal system were optimised to reproduce the present data and all available reliable experimental data in literature.

Jun 19, 2024