Search Documents

By A B. Richards

A brick veneer house located on a open-pit coal mine lease has been subject to ground vibration levels of up to 222 mm/s, and air vibration levels of up to 145 dBL. The dynamic response of the structure was measured with accelerometers, geophones, and strain gauges as part of a project investigating the response of brick veneer houses to blasting. This paper outlines the project, and provides information on brickwork strength, foundation investigations, and observations on damage due to blasting. Correlations have been made between crack behaviour and factors such as blast vibration levels and rainfall.

Jan 1, 2001

By K A. Bunker, A D. Campbell, E Ah Mu, A R. Penney

The Ernest Henry mine is a transverse sublevel cave (SLC), which is relatively unique due to the 45 degree inclination of the orebody. To economically recover ore, each sublevel is horizontally offset from the previous level by around 25 m, depending on the orebody geometry. Mine development, slotting and initial production within this zone occurs in a high stress abutment that increases in magnitude at depth. These areas are seismically active and close to the hanging wall where cave propagation is yet to initiate. High stress conditions and the close proximity to the cave seismogenic zone results in challenging geotechnical conditions in the step out zone of each level and requires management of hazards including stress driven rockfalls, rock bursts and pillar failure.This paper outlines how these hazards were forecast using numerical modelling and geotechnical monitoring. Risk management techniques included dynamic ground support design, development of a new mine layout and extraction sequence as well as delayed re-entry into seismically active areas. Ongoing monitoring, instrumentation measurements and field observations were used to track the effectiveness of the controls.Future production levels are forecast to experience increasing stress and seismicity, which will increase demand on excavations and installed ground support. Ensuring the techniques and controls for monitoring, measuring and mitigating stress and seismic hazards are enforced is essential for continued safe production.CITATION:Campbell, A D, Bunker, K A, Ah Mu, E and Penney, A R, 2016. Managing stress and seismicity in an inclined sublevel cave, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 319–328 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

A new approach to resource estimation at the exploration stage is emerging, based on the application of simple software techniques. The techniques combine the power of interactive graphics with proven database, analysis and estimation tools. With effective use of these tools the geologist now has maximum chance of deriving a reliable structural and grade model from the limited exploration data. Unlike cutoff-based polygonal methods, the resultant geological model can immediately be used to evaluate any economic scenario.These modelling techniques are embodied in MINEX-3D, an Australian software system. With the emergence of the 386-based PC and high resolution (VGA or better) graphics, MINEX-3D makes the power of this new 'desktop geological modelling' accessible to most exploration geologists.

Jan 1, 1990

The mobility of radionuclides released into aquatic, terrestrial and subsurface environments by mining, industrial processes is an area that deserves significant scientific attention. The presence of microorganisms in these environments can influence the transport of radionuclides. Free-living microorganisms constitute mobile suspended particles that may have a radionuclide sorbing capacity higher than that of the environment. Radionuclide transport will then proceed faster with than without microorganisms. In contrast, if the majority of the microorganisms are growing in biofilms on surfaces, transport of radionuclides may be reduced. Microorganisms can directly sorb radionuclides either within the cell structure or on the cell wall. Radionuclides could also be sorbed by minerals precipitated by microorganisms. Microorganisms produce complexing agents that can influence radionuclide mobility. The involvement of microorganisms in biogeochemical processes is related to their ability to include various chemical elements and their combinations into biochemical redox reactions. Microorganisms can alter the extent of radionuclide oxidation that results in their deposition as a result of the formation of insoluble forms. Some studies have shown the bioremediative potential of stimulating reducing bacteria to use some of the soluble radionuclides as electron acceptors and thus precipitate them out of solution. The microbial involvement in providing a barrier for radioactive element migration (uranium, technetium) and the formation of ores (eg uranium) has been justified. The mediated impact of microbial activity on radionuclide migration occurs through its effect on the ambient geochemistry by geochemical speciation changes, pH changes and changes to the ambient redox potential. As the mobility of many radionuclides depends on the pH and redox potential of the environment, these microbially mediated geochemical changes can influence radionuclide migration through changes to both the dominant radionuclide species and mineral phases.

Jan 1, 2004

The Golden Cross mine is a Joint Venture between Coeur Gold New Zealand Limited, as Manager, and Viking Mining Limited. The mine is targeting Zero Lost Time Accidents as a goal.   The Golden Cross operation produces gold and silver from both underground and open pit. The mine is based on an epithermal gold-silver deposit. Treatment of ore is on a campaign basis for each ore type (i.e. underground or open pit). Milling is conventional SAG Mill and Ball Mill grinding circuit followed by carbon in pulp recovery of gold and silver. All tailing materials are treated through the Cyanisorb process to reduce cyanide levels prior to being discharged into the tailings dam.

Jan 1, 1995

This paper discusses some topical issues on the mining administration and legislation fields including:  1. Licensing û Administration and associated specialist functions including:Processing and volumes of mining privilege applicationsFuture organisation and possible decentralisationSpecialist staffFacilitiesGuide to the Mining Act 1971 2. Mining Amendment Act 1981 Transitional procedures 3. Planning Tribunal First hearing of objectionsPoints of principle resulted there from 4. Quarries and Tunnels Bill Currently before Parliament û implications for metallurgical mining

Jan 1, 1982

By T J. Orr

The changing demographics of the mining industry make successful passing of knowledge and skills to the next generation critical. Training methods and technologies are being developed to meet this need. Twenty years ago classroom training was largely a one-way transfer of knowledge through instructor lectures. In contrast, instructors today can use virtual reality technologies to guide trainees as they fully participate in learning experiences. Trainees can interact with the virtual work environment, co-workers, and equipment without being exposed to workplace hazards. The speed of advancement in mine safety, health, and production training shows no sign of slowing in the next 20 years. Researchers at the National Institute for Occupational Safety and Health have studied and participated in the evolution of miner training. A look at training materials they have created in the past and those they are currently developing reveals changes in methods and technologies over time and also key characteristics which have remained constant. Possibilities for the future can be discussed in the framework of an implementation of virtual reality in new miner training sessions. The example computer-based training package teaches new miners to read mine maps and provides opportunity to practice navigation skills in a virtual mine. With this æserious gameÆ, trainees experience the look and feel of moving through an underground coal mine while in the safety of their classroom. During field-testing in 2007, trainees and instructors responded very favourably to this new way of learning. The software was usable by mine trainers with even limited computer expertise and could be installed on the affordable computers they were using for their more traditional slide presentations. The Underground Coal Mine Map Reading TrainingÆs foundation on past successful development strategies and its acceptance by todayÆs instructors and trainees provide valuable lessons for developing training materials, strategies, and technologies for miningÆs future.

Jan 1, 2008

By J Brisebois

The derelict Lake George Mine is located at Captains Flat in NSW, acommunity of approximately 450, which lies some 43 km southeast ofQueanbeyan. It straddles the Molonglo River, which flows toQueanbeyan and thence the nationÆs capital, Canberra. Catastrophictailings dam failures in 1939 and again in 1943 resulted in the transportand dispersion of thousands of tonnes of sulfidic wastes downstream,with terminal settling in Lake Burley Griffin, in Canberra. The mine wasclosed in 1962, and major rehabilitation in 1996 - 1997 addressed the riskof further collapses, and reduced water flow into the underground mine.Nevertheless, acid mine drainage from the mine, and seepages ofcontaminated water from the capped tailings dumps continue to pollutethe Molonglo River for some 30 km downstream.Environmentally, the highest contributor to the total contaminant loadof the river is the Main Adit Spring. This was shown to be a constantgroundwater-driven acidic flow, with contaminant generation resultingalmost entirely from the ingress of gaseous oxygen into the undergroundworkings. Long term remediation may be possible at source, by pumpingreducing gases into the sealed mine, but the probability of thistechnology succeeding to the required degree is yet to be demonstrated. For at least the medium term, treatment of contaminated water flow(s)will be required to achieve any of the water quality targets that may beapplicable to the river. Three methodologies were short listed, but anumber of strategic uncertainties remain, which the NSW Derelict MinesProgram will address. Future risk arising from long-term contaminantrelease by the treatment wastes must be considered. Appropriate data,and realistic long-term performance parameters regarding the relativestabilities of water treatment sludges are scarce, and make properevaluation of competing technologies problematic.

Jan 1, 2003

This paper presents a review of computer techniques for the automatic contouring of geological and geophysical data with output as interactive display on graph plotters or graphics terminals and passive display on automatic drafting tables. The advantages of the method of fitting a triangulated surface to randomly distributed data using an advancing front algorithm are described, as well as the technique for determining interpolated values for the production of contour line segments and a contour smoothing algorithm. This contouring method is employed by the Geological Survey of Queensland and is implemented as an interactive system. An alternative method ideally suited to randomly distributed data involves the use of piecewise parametric cubic splines. This method which is ideal for sharp variations in magnitude and areal extent typical of geophysical anomalies is discussed. The mathematics of surface interpolation using non-parametric splines and an explicit piecewise surface fitting technique are discussed. Curve tracing techniques which are suitable for automatic contouring are also presented and the inherent advantages of interactive contouring using on-line plotters and graphics terminals for previewing of displays are described.

Jan 1, 1977

By J Pric, M Fulton, C Xia

A cyanidation study was conducted on a mild refractory gold ore sample from the Central zone of Clarence Stream Property, owned by Freewest Resources Canada, to develop a leaching strategy to extract gold. Gold, at a grade of 8.00 g/t, is present as native gold, electrum and aurostibite. The ore also contains 2.8 per cent pyrrhotite, together with several antimony minerals (0.8 per cent berthierite and gudmundite, 0.18 per cent native antimony and stibnite). It also exhibits weak preg-robbing properties with 0.16 per cent organic carbon. Aurostibite, a gold antimony compound, is particularly known to be insoluble in cyanide solution. The antimony dissolves in cyanide solution to form antimonates, which retards gold dissolution. Industrial practice of extracting gold from aurostibite generally consists of producing a flotation concentrate, which is leached in a pipe reactor at low alkalinity and high oxygen pressure with about 20 g/L cyanide. The proposed new approach is efficient and allows the extraction of gold directly from an ore at atmospheric pressure and a low cyanide concentration at pH 10.5. The effects of grinding, pretreatment, lead nitrate, kerosene and cyanide concentrations have been investigated. The maximum gold extraction obtained on the ore was 87.9 per cent using 800 ppm NaCN, 500 g/t lead nitrate, 30 g/t kerosene, DO 10 ppm and pH 10.5 in 168 hours. The associated cyanide consumption was 1.3 kg/t. The additions of lead nitrate and kerosene increased gold extraction. In comparison to a P80 of 74 ¦m, a P80 of 30 ¦m significantly increased gold extraction. Gold in solid solution in gudmundite and arsenopyrite was believed to be responsible for the unleached fraction until mineralogical analysis of hydroseparation concentrates of leach residues showed that most of the unleached gold occurs as aurostibite, either as locked grains in sulfides/sulfarsenides or as grains with passivation rims of an Au-Sb-O phase. Coarse gold was also found. Gold extraction was not sensitive to cyanide concentration from 250 ppm to 1200 ppm NaCN and high pH was detrimental. Decreasing the cyanide concentration reduced the cyanide consumption to 0.85 kg/t. The removal of coarse gold using a Knelson concentrator and a Mosley table prior to leaching increased the gold extraction to 90.4 per cent (leach residue at 0.77 g/t).

Jan 1, 2007

Spatial continuity as described by a variogram is a reflection of the underlying mineralisation/geology. Modelling of the spatial continuity (variogram) must account for both the quantitative data (ie sample grades), on which the variogram calculations are based, and the qualitative information as provided by the geological interpretation. An understanding of the geology and the variogram interpretation tie together the sample values and allow us to go beyond the actual data (Journel, 1995). Variography makes geology transportable and allows the geological interpolations to be channelled downstream into mine planning, ultimately affecting the economic decisions surrounding a deposit. As such the process of variography and resource modelling is critical. Thus consistent expert decisions need to be made which force geologists to have a closer look at the available information and the geological interpretations. The aim of this paper is to provide an overview of the latest developments in visualising variography and to demonstrate their usefulness in decisions regarding the spatial continuity of mineralisation. New ideas concerning potential future developments in visualising and modelling spatial continuity through variography are introduced.

Jan 1, 1996

THE filter-press, which has done so much for the successful-treatment of the sulpho-telluride ores of Kalgoorlie, has a serious rival in the vacuum process, and this paper is written with a view to arousing more interest in the cheaper working of the press, it being doubtful whether its efficiency in extraction can be improved upon. Before proceeding with the actual working of the press, it may be as well to make brief mention of the character of the ore treated at the Associated Northern Blocks, where these notes were compiled. A sample from several weeks' run was taken of the raw ore, with the following analysis...

Jan 1, 1911

By A B. Christie, R L. Brathwaite

Since the first occupation of New Zealand in 800 - 900 AD, various useful minerals, rocks, and energy resources have been identified and extracted. The Maori prized greenstone for ornaments, tools, and weapons, used argillite and obsidian for tools, and decorated their carvings and bodies with colours made from clays, limonite, and vivianite. They were aware of coal (waro), but are not known to have used it for fuel. Before 1840, visiting whalers used coal from Shag Point to heat their trypots. Mining activities got underway in the 1840s, with the finding of manganese oxide deposits in the Bay of Islands, Kawau Island, Waiheke+ Island, and Taieri Mouth. Secondary copper ore was mined on Kawau Island (1846 - 1869), and native sulphur was exported from White Island to Europe. The discovery of gold at Coromandel in 1852 and a few years later in Northwest Nelson and Otago opened the way to gold rushes in these areas and subsequently in Marlborough and Westland. Mining of alluvial gold evolved through sluicing to the invention of gold dredges; first (1863) was the simple spoon design, but later (1881) large steam-powered bucket-ladder machines weighing around 3800 tonnes were built. Most of the gold dredges had gone by the early 1960s, following a revival in the 1930s, but one large dredge operates today on the Grey River. Other mining events included: underground mining of coal from 1849 and underground mining of lode gold from 1863 in the Coromandel, Reefton, and Otago fields. Most outcropping coal deposits had been discovered by 1870. Building stones were used by the early settlers for construction of houses, churches, banks, public buildings, and some universities from 1836. Aggregate for roads, railway ballast, and concrete, and limestone for cement and fertiliser, and clays for bricks and china have been quarried for many years.

Jan 1, 1993

LIST OF CONTENTSAbstractIntroductionSelected Sections of the Broken Hill LodeLocality PlansPetrology1. Zinc Corporation Mine: DDH. 5.98, section 30, No. 26 level2. Zinc Corporation Mine: DDH. 838, section 30, No. 13 level3. Broken Hill Sonth Mine: 60 ft. cont01(r above 1170 ft. level4. Broken Hill South Mine : No. 7 shaft section, 1370 ft. levelOrigin of garnet sandstone5. Barrier Central Pty. Ltd.: DDH. tJ.93, Block 136. North Broken Hill Ltd.: Junction mine, DDH. 602, No. 10 level7. North Broken Hill Ltd.: Jnnction mine, DDH. 588, No. 11 level8. North Broken Hill Ltd.: North mine, DDH. through Southern ore body, 3370 ft. level9. North Broken Hill Ltd.: North mine, Northern ore body above 2300 ft. level(a) Southern end, section 27, 77 ft. above rails(b) Northern end, section 30, 6.9 ft. above rails(c) Miscellaneons samples, sections 27 and 28Relative time of ore depositionSericitizntionStructural significance of sericitizationGCLhnite OrthoclaseApatite GarnetManganese SilicatesAlteration of manganese silicatesRelation of zinc and lead to the silicatesZinc in manganese-bearing silicatesLead in potassium and lime silicates and apatite

Jan 1, 1959

The Golden Cross mine commenced production in December 1991. Both open pit and underground mines produce 1000 tonnes of ore per day. Mining techniques are discussed along with results and variations to proposed methods of extracting the ore.

Jan 1, 1992

Grinding and Flowing Investigation on Dry Stirred Ball Milling in Order to Determine the Influence of Grinding Aids Huge difficulties of the great ultra fine ground material production in dry stirred ball mill are the cohesion and agglomeration of the particles. During grinding the material stick on the grinding wall and the grinding media furthermore the grinds start cohere, making aggregation and agglomeration to appear. Due to these effects the particle size will not decrease after a certain value during grinding and the energy demand increases significantly. According to experience on fine grinding in ball mill, it is well known that these effects can be reduced with the use of grinding aids. The influence of grinding aids has three different effects: due to the adsorption strength reduction (Rebinder effect) the grinding resistance of the material decreases; the surface energy diminishes and the agglomeration liability decreases; and the flow properties of material improve. The aim of this study is to investigate the flow properties of fine grinds and the effect of grinding aids on flow properties in case of dry stirred ball milling. In addition, the influence of grinding aids was investigated based on the particle size distribution and specific surface area of grinds and the specific energy demand of grinding. The examinations were carried out with three different model materials (limestone, clinker, quartz) using the usually applied grinding aid. The flow properties were measured by the Jenike shear cell; the particle size distribution and specific surface area were measured by laser particle size analyser (Fritsch Analysette 22), grinding energy demand was measured with microcomputer controlled digital energy meter. It can be said that under certain measuring circumstances the influence of grinding aid on flow properties can be demonstrated by Jenike shear cell, so the grinding result is in correlation with the flow properties of grind.

Sep 13, 2010

By D La Rosa, G Power, K Riihioja

In underground mining, the often unpredictable variability in ground conditions may lead to the application of suboptimal drilling and blasting patterns, resulting in poor performance. Experience and pertinent information to develop and implement improved drilling and blasting strategies can be easily lost due to the lack of means to help engineers store, access and manage this information. The Julius Kruttschnitt Mineral Research Centre (JKMRC) through a series of industry funded applied research projects has been developing a system that can facilitate the drill and blast design, analysis, auditing, documentation and data management processes. The system is a hybrid between an information management software module called BMS (Blast Management System) and two design and analysis modules, 2DRing for underground production blasting activities and 2DFace for development blasting activities. A concise description of the software tools and its applications are given in this paper, supported by two case studies. Opportunities to further develop the software are also highlighted, they include options to integrate these tools to existing drilling and blasting automation systems and portable computing technology to facilitate the design, implementation and continuous improvement processes.

Jan 1, 2001

Most mines in the Bundamba, North Ipswich, and Rosewood districts of the West Moreton coalfield of south eastern Queensland have installed washing plants during the last five years. Many problems were encountered in their installation, including the small size of washing plant required in many cases, the economical minimum ash content under present and future market requirements, production from a one-product washbox of large and small coal of quality to satisfy both markets, measures to avoid adding unnecessary moisture to the washed slack coals, and excessive middlings in some coals or soft clay in others.INTRODUCTIONIt was fortunate for Brisbane, which was to become the capital of a new State, Queensland, in 1859, and grow into a city of over half a million people by the time of its centenary, that coal was found in abundance almost on its doorstep near Ipswich, the first mine being opened at Redbank in 1843. This was followed by the opening of many more mines in that district and, some 40 years later, in the nearby Rosewood district where high-volatile gas coal was produced (Fig. 1). These discoveries ensured a supply of reasonably priced coal (currently about 85/- per ton delivered) in Brisbane, but the quality is inferior to that of other coals mined in Queensland beyond economic range of Brisbane.Various factors led to an increase in the average ash content of the West Moreton coals during and after the war. Between 1940 and 1952 the gasworks coals rose in average ash from 13 8 per cent to 23·9 per cent and the powerhouse coals from 17·1 per cent to 27·1 per cent. This drift was arrested by the installation of 28 screening and picking plants from 1952 onward, but it became obvious that mechanical cleaning of the coals was essential due to the competitive market for coal and the worsening quality of reserves.

Jan 1, 1963

Blasting is a common practice in mining whereby solid rock is fractured, using explosives, to a more manageable size. The effectiveness of blasting influences a number of downstream activities such as shovel digability, crusher throughput and mill throughput. As the cost of explosives is relatively low compared to milling costs (mainly due to power consumption), blasting practices can be optimised so that the downstream processes are made more efficient, and an overall cost saving made. This is the basis of the Mine to Mill approach. The effectiveness of the blasting is influenced by two main factors, the blasting practices used (eg explosive amount and type) and the geology of the area. As the geology cannot be altered, the blasting practices must be refined to create optimum blasting. Kalgoorlie Consolidated Gold Mines (KCGM) Fimiston operation, located in the heart of the Kalgoorlie Goldfields is the largest gold mine in Australia. Mine to Mill at KCGM has had varied success, with initial positive indications being lessened by a number of factors, including the increase in the amount of voids.

Jan 1, 2003

"DEEPHOLE " or "Longhole" drilling is the name given to the drilling of prospecting holes with the pneumatic hammer drill. The drilling bit is of the same form, and is prepared in the same way as ordinary rock drill steel, and is extended to the bottom of the hole by sectional hollow rods, through which water is forced.The cuttings from the hole provide a sample of the ground drilled.Deephole drilling was developed at an American mine where the cost of diamond drilling, owing to loss of diamonds, was excessive, and proved very successful, holes being drilled as deep as 220 ft., in limestone, at a cost of one dollar per foot. The use of the method in other mines, and in a variety of rocks, has since been described in the technical literature. From the published descriptions the following data are drawn:

Jan 1, 1930