Search Documents

By G Lumley

PlannersÆ optimism (or maybe commercial necessity) means that most mine plans use equipment rates that are rarely achieved (Lumley and Beckman, 2009). This lack of understanding of what equipment actually moves is causing erroneous equipment forecasts, leading to incorrect mine development plans and economic evaluations. Compounding this problem is a downward trend in actual equipment performance in some areas. Consequently, the presentation of realistic mine plans that are actually achieved in practice is not a common occurrence. However, rational, fact-based mine planning is available to those who want it. Hundreds of millions of cycles of data from open cut mining equipment has been collected from mines around the world since 1992. This unique and highly valuable databank is growing at an exponential rate and is being used by a number of our big miners to support rational and fact-based decision-making. However, neither the use nor the appreciation of the value of this data is universal. There is a challenge to everyone in the mining industry - how do you access value from it? The databank was drilled into and the results analysed for, the Australasian Mining and Metallurgical Operating Practices (AMMOP) publication (Lumley, in press). For this paper the analysis has been extended to include interpretation of trends for draglines, shovels, excavators and trucks. It investigates trends between coal and non-coal mines and across geographic areas. It is known that mining equipment performance in most sections of the industry is falling. This paper attempts to quantify the fall and provide explanations. The trends are analysed to extract the reasons behind the changes and most importantly, what can be done about it.CITATION:Lumley, G, 2012. Understanding trends in performance of open cut mining equipment, in Proceedings Project Evaluation 2012 , pp 203-224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By T Howard, J E. Everett

BHP Billiton Iron Ore has replaced the conventional product quality control batch system at Yandi with the Continuous Stockpile Management System (CSMS) centred on a fully integrated æcontinuousÆ stockpile flow from mine planning through to port reclaiming. With increasing tonnage rates, tight operational coupling associated with the original batch system caused production interference which achieved final product quality but in an increasingly inefficient manner. This innovative approach places a continuous emphasis on product grade control and takes full advantage of the most appropriate blending opportunities of the mine to port planning and production system in order to reduce the natural variability of the ore to an acceptable level. To implement continuous control, product variability throughout the process is classified as long-term and short-term. Long-term variability is best controlled through the monthly mine planning process which determines monthly grade targets while taking into account optimum mine development. In the past, attempts to control long-term variability were made at the port through selective stockpiling and reclaiming which reduced operational efficiency. Short-term variability is best controlled around the monthly mine grade target by daily mine production scheduling, train sequencing, stacking into port stockpiles of appropriate size and systematical stockpile reclaiming. The implementation of the new system has maintained customer accepted shipping grades and has provided significant improvements in resource utilisation, operational efficiencies and costs.

Jan 1, 2002

By Letz H

An investigation of earthquake hazard in Papua New Guinea (PNG) by a yearly extreme magnitude method using the magnitude 7 earthquake record since 1900 shows that the Bougain-ville Island seismic zone is by far the most active, followed by the New Britain and northern mainland PNG regions. Return period for magnitude 7.0 earthquakes occurring in normalized 10,000km2 areas of the Bougainville Island, New Britain, Huon, West Bismarck, North Sepik and Ramu seismic zones is 37, 60, 81, 88, 125 and 125 years respectively. These areas are much more active than the California Seismic Zone 4 region including the San Andreas Fault, which has a normalized magnitude 7.0 return period of 299 years, calcul-ated here by the same method.Only southern PNG, including the Papuan Fold Belt and most of the Bismarck Sea, are less active than California Zone 4. The Papuan Fold Belt is only marginally less active than California Zone 4, but more active than the State of California taken as a whole.

Jan 1, 1994

P.IISTRACTThe Pacific Rim is advantaged by the uniqueness and diversity of its geological features. Why then is geology given so little regard in the education systems of the countries of this region? Not that these countries differ greatly from those in other parts of the world. Papers presented during the Precollege Geoscience Education session at the 28th International Geological Congress (28th IGC) held in Washington, July, 1989, indicated strongly that the problem is universal. There is a marked decline in interest in the Earth sciences and many nations are looking towards methods that might change this trend. Problems affecting geological education include the lack of purpose and direction, its obsolete curricula and the difficulty in attracting gifted students.The world-wide plight of geology comes at the very time when it should be fundamental to a public understanding of the global effect of human population pressure. There is a universal awareness of "the environment" but very little awareness of the science that has supplied most of the data. Geology, as the science of the Earth, is of paramount importance to an understanding of our life on this planet, particularly in its role as the source of our every need.

Jan 1, 1990

By Mortensen JK, Lang JR

The Canadian Cordillera contains numerous classic porphyry deposits and several unusual subtypes, including the alkaline suite of porphyry Cu-Au deposits and the Tombstone magmatic suite and associated Au¦W deposits. The alkaline suite formed in collisional settings in island arcs whereas the Tombstone suite was emplaced in an active fold and thrust belt in a continental arc. In addtion to different regional settings, these suites differ in the type of underlying basement, metallogeny, and the styles of mineralization. Both magmatic suites were emplaced over short intervals, probably in response to specific tectonic events. In the case of the alkaline suite, the tectonic event promoted magmatic processes suitable for the formation of porphyry Cu-Au deposits. The tectonic environment is less well constrained for the Tombstone suite, but the result was the formation of distinctive porphyry and intrusion-related Au¦W deposits.

Jan 1, 1995

A resource rent taxation scheme is based on the concept of taxing the rent or surplus profit generated from primary industry activity. Rent has been defined as profits that remain after deduction of company income which corresponds to the minimum return necessary to attract private investment to a new project.Rent taxation schemes on the mining industry within the Australasian region have been examined and widely discussed during the decades of the 1970s and 1980s. Forms of resource rent taxation schemes have been imposed on Papua New Guinea mining, some sectors of Australian petroleum, the Roxby Downs venture and are being discussed for the New South Wales coal industry. While no introduced applications have been pure rent taxation schemes, the concept has generally come to encompass arrangements which tax rent at a partial rate which may or may not vary with the level of profitability or return.An examination is made of a number of the more recent schemes. Aspects which should be considered in implementation of new forms of this taxation are discussed. It is concluded that there is an increased acceptance for this form of taxation on the Australian mining industry.

Jan 1, 1990

By Browner R, Kyle J

The adsorption of gold cyanide by the weak base ion exchange resins, PAZ-4¦ and Duolite A-7C, the neutral polymeric adsorbent, Amberlite XAD7¦, and the strong base resins, PAZ-8~a and IRA-400 have been studied in both low and high salinity waters, and their performance compared with activated carbon. A systematic study has also been made of the effect of different ions (Na+, Cat+, Mgt+, Cl', SO4) ) on the gold adsorption capacity and kinetics of these resins. The results indicate that, contrary to popular belief, the ion exchange resin, can perform effectively in highly saline environments. The performance of the neutral polymeric adsorbent im- proves with increasing salinity but cannot match the performance of the ion-exchange resins.

Jan 1, 1991

PAPERS : 1 COMPUTER AIDED DESIGN OF MINE WATER MANAGEMENT - Z KESSERU 2 THE HYDROGEOLOGICAL PROBLEMS OF GROUNDWATER PROTECTION IN MINING REGIONS - V A MIRONENKO 3 WATER MANAGEMENT OF THE MAE MOH PROJECT -òò SIRI CHITCHOB 4 WATER MANAGEMENT AND WATER TREATMENT AT GOLDPN CROSS - M P A WILLIAMS

Jan 1, 1988

How Particles Stick to Bubbles - The Influence of pH and Hydrophobicity in Flotation

Sep 13, 2010

By A M. Barrett, P J. Chapman

As filtering technology improves and there is an increased focus on environmental impacts, the concept of managing fine coal rejects by filtering, mixing with coarse rejects and dry stacking them is being considered more seriously. In Queensland, there appears to be a desire from regulators to move away from wet rejects facilities towards dry-stacked facilities, resulting in a change in the risk profile for the facility.A coalminer has a site with many constraints, including limited area that is not planned to be undermined and nearby rivers that are prone to flooding. The design of a dry-stacked facility that meets the operational requirements and environmental compliance criteria is challenging in subtropical climatic settings, where there is a need to consider wet seasons with high-volume, sustained rainfall events. The impact of the rainfall is multifaceted, requiring careful surface water management to separate clean and contact water, adequate foundation preparation to limit seepage to groundwater, management of stack stability given a potentially high phreatic surface and the avoidance of potential flood zones. These design constraints were compounded by a limited area available for rejects storage that would not be undermined.This paper presents a summary of the conceptual design of a dry rejects facility, including consideration of regulatory and client requirements, provision for expansion while also considering progressive rehabilitation, diversion of clean water as much as practicable during operations and siting constraints. A step-by-step concept is presented that addresses each constraint during the life of the facility.CITATION:Barrett, A M and Chapman, P J, 2015. Conceptual design of a dry-stacked coal rejects facility in a subtropical climate, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 27–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Hayes K. M, Ostwald J

Compacted tablets of hematite ore (containing clay and quartz gangue) and limestone were heated in air in an ULVAC-RIKO rapid heating furnace to maximum temperatures in the range 1200-1350°C.The resulting sintered products were examined in terms of mineralogy, texture, strength and reducibility. The sintered tablets are a good analogue of normal plant sinters. These investigations have shown that sinters of optimum reducibility are produced in the narrow temperature range 1250-l275°C. Conditions for the production of such highly reducible sinters under plant conditions are discussed.

Jan 1, 1984

As Project Managers for the Blair Athol Coal Mine Project, CMPS selected a number of computer systems to assist in project control. The areas where computers were used were: 1) Planning & Scheduling 2) Procurement Reporting 3) Document Control 4) Accounting 5) Cost Control 6) Control of project management and engineering manhours The computer packages selected were generally effective in their own areas. During 1982, CMPS acquired an in-house project control package called GC/Cue. Project control systems for the project are progressively being set up on this system. The advantages of this type of system are: 1) Improved accessibility of information, due to on-line operation and the use of VDU's. 2) Improved turn around time for computer runs and production of reports. 3) Improved presentation and format of reports. 4) Lower costs.

Jan 1, 1983

Hydraulic backfill is generally retained in stopes using permeable barricades. Mitchell et al (1975), Mitchell (1992) and Grice (1989) have shown that under normal drainage conditions, barricades experience low levels of loading. Cowling et al (1988) have also shown that barricades are susceptible to piping failures if excess water has ponded on the upper backfill surface and if leakage of backfill from the barricades has occurred. During 1997, six hydraulic backfill barricades failed in four different Australian mines. Fortunately, in each case, the quantity of backfill slurry released was small, and no injuries to personnel nor damage occurred. Detailed investigation of two of the incidents showed that the primary cause of failure could be attributed to the delivery of excess quantities of transport water from the low-density slurry. For each of the incidents investigated there was evidence of the development of piping failures, which resulted in hydrostatic loading conditions on the barricades from the ponded water on the upper backfill surface. The circular failure surfaces in the barricades were characteristic of the application of point loading conditions. This paper discusses the circumstances that led to these incidents and analyses the modes of failure. The standards for the safe operating of hydraulic backfill systems are reviewed along with requirements for ongoing management and control. The design requirements of barricade construction are analysed and some appropriate guidelines introduced.

Jan 1, 1998

By Kikuta K

ISP (Imperial Smelting Process) produces zinc and lead simultaneously from zinc and lead sulphide concentrates and recovers copper and precious metals into a lead bullion. The strength of sinter is important to keep permeability in the shaft of the Imperial Smleting Furnace. The residual sulphur content of the sinter is also important as it causes metal losses into slag. The paper describes an investigation into the sintering operations to improve sulphur elimination and sinter strength. The micro structure of the sinter and the effect of the blast rate, sintering temperature etc have been studied.

Jan 1, 1993

By S P, F Villanueva, R Palomo, D Meadows

During 2002, design and development of the worldÆs largest flotation cell was completed. The cell is the mineral industryÆs first 257 m3 flotation cell, and represents a major development in the design of larger flotation cells, with a 50 per cent increase in cell volume over the widely installed 160 m3 WEMCO« SmartCellTM flotation machine. It is anticipated, in the next few years, world-class copper sulfide concentrators will incorporate 257 m3 flotation cells in their rougher-scavenger flotation circuits. The prototype 257 m3 cell, No 250 SmartCellTM flotation machine is installed in Minera Los PelambresÆ existing rougher flotation circuit. The machine is located in front of the first cell in Row 1 and is followed by nine No 130 SmartCellTM flotation cells. The unit has been in operation since April 2004, and has proven itself in this duty. A key to the successful development of the equipment has been the emphasis placed on fundamental hydrodynamic scale-up criteria. Hydrodynamic factors include superficial gas velocity, water (pulp) circulation through the draft tube, and pulp mixing (distribution) characteristics. This paper will review the scale-up criteria of the No 250 flotation cell, and a case study will be presented on the in-plant testing of the equipment. The case study will document the metallurgical and hydrodynamic performance of the machine. It will also illustrate the economic benefits derived by incorporating larger flotation cells in a modern copper sulfide concentrator.

Jan 1, 2005

By L Bartsch, M Kelahan, E Wingate, J-S David

The use of column flotation cells for recovery of phosphate is becoming more common practice in certain parts of the world (Brazil, Russia) where igneous phosphate ores are processed. Igneous phosphates are generally finer grained (< 200µm) than some of the traditional sedimentary phosphates (<400µm). Australian phosphate from the Georgina basin is sedimentary, but has a much finer grain size (typically < 106µm) than similar deposits in North Africa and the USA.In 2013, Arianne Phosphate completed a bankable feasibility study for the development of their igneous phosphate deposit at the Lac a Paul site in Quebec. Initially, lab test work and bench scale piloting indicated that using traditional mechanical flotation would be able to produce adequate concentrate grade and an economic level of recovery, but would necessitate the installation of a complex and operationally challenging flotation circuit. Later pilot plant testing using column cells resulted in a significant reduction in process complexity and facilitated the processing of the -20µm ore fraction which resulted in a 10% increase in P2O5 recovery and a 5% increase in concentrate grade %P2O5.Flotation column testing achieved a concentrate grade of 38.6% P2O5 at a P2O5 recovery of 90%. Using a mechanical flotation cell circuit, the concentrate grade was 36.4% P2O5 with a P2O5 recovery of only 78.8%. A noticeable feature of the testing was the simplicity of the column flotation circuit configuration (Rougher + 2 stages of cleaning + Cleaner Scavenger) compared to the mechanical flotation cell circuit (Rougher + Scavenger + 3 stages of cleaning).The financial benefit for this case study was estimated using a sales price of US$ 195/t FOB for a 38.6% P2O5 product, and an assumed cost of production of US$ 95/t, the netback price is calculated at US$100/t. For a daily milling rate of 55,000t/d, the improved flotation performance provides additional concentrate production of 1,203t/d. Using the netback price calculated above, this calculates to additional gross profit of US$ 120,260/d.Annualised, this equals US$ 40.7 million in additional revenue for a similar or reduced CAPEX.The use of column flotation on fine grained phosphate ore types often requires fine grinding and desliming to liberate the phosphate value, such as the Australian sedimentary phosphate ores. This may enable the development of deposits previously regarded as uneconomic.This paper discusses the potential benefits available to operators, and developers of new projects, for the use of column flotation cells in their metallurgical circuits as assessed by an engineering company.CITATION:Wingate, E, Kelahan, M, David, J-S and Bartsch, L, 2015. Does it make cent$ to use flotation columns for phosphate beneficiation?, in Proceedings MetPlant 2015, pp 353–365 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Parker RJ, Swindells CF

The authors have used the geotechnical study for design of the South Wall of Mt. Newman Mining's Mt. Whaleback Mine to illustrate how geotechnical studies can be economically justified. This is achieved by relating the savings resulting from increased ore recovery and prevention of failure to the cost of the study. An outline of the geotechnical study is provided in the paper, including a brief description of the innovative methods used to investigate geological structure of the mine and descriptions of the methods of slope reinforcement adopted.

Jan 1, 1986

By S C. Dominy

Various styles of gold mineralisation pose problems during sampling because of their complex gold grade distribution and presence of coarse gold. Effective sampling and sample preparation forms the basis of resource estimates. The design of a sampling and assaying protocol must be based on a thorough understanding of the mineralisation in question, which should include consideration of gold particle size and mass distribution. The proportion of coarse gold within samples has a profound effect on the requirements for sample preparation and assaying. Choice of preparation procedure and assay type is of critical importance if sampling errors are to be minimised. Traditional fire assays, using small charge sizes, often understate assays gained from large charge sizes and techniques such as screen fire assay and LeachWELL. Proper application of the Theory of Sampling reduces errors during collection, preparation and assaying. A quality control/quality assurance program must be implemented and critically assessed. A case study from the Ballarat mine is presented, which is characterised by substantial quantities of coarse-gold hosted in quartz veins. Diamond core drilling is the key input into resource delineation. A number of different sampling and assay options have been trialled over the recent project history. The current sampling protocol utilises whole drill core, using LeachWELL assays after logging and photography.CITATION:Dominy, S C, 2017. Sampling coarse gold-bearing mineralisation – developing effective protocols and a case study from the Ballarat mine, Australia, in Proceedings Eighth World Conference on Sampling and Blending , pp 71–84 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

This study is to compare reinforcement of rebar and spiral bolts using laboratory pull-out test. For this purpose, the pull-out test was performed in laboratory for a curing period of 7- and 28-days. Based on the results of the laboratory pull-out test, the pull-out load of two support members rapidly increased with displacement until the breakpoint and then gently increased with displacement. The maximum pull-out load of spiral bolt was larger than that of rebar bolt. This implies that a spiral bolt is more stable than a rebar bolt for securing the stability of a ground or rock mass when a support was installed in a ground or rock mass under the same condition. In addition, the maximum external pressure of two support members increased with pull-out load and with displacement and the distribution of external pressure was commonly larger at the upper part than at the lower part of specimen. This indicates that the bond failure location by pull-out load should be mainly occurred at the surface portion of specimen. In conclusion, the reinforcing effect of a support depends on a curing period and a type of support member, and reinforcement of a spiral bolt is more effective than that of a rebar bolt.

Dec 6, 2010

By D Fergusson, J D. St George

Highwall stability is a major consideration in optimising opencast mine geometry. It involves assessing the risk of those slope failures that are large enough to have significant cost, safety and/or operational implications. These risks are then balanced against the value of the resource to arrive at an acceptable slope design. Load-deformation models (commonly referred to as ænumericalÆ models) of slopes provide a powerful tool in this decision-making process since they can be verified well before slope failure occurs. This gives the slope designer increased confidence in reviewing designs during excavation, potentially allowing early revision of pit geometry to either increase or decrease safety margins as appropriate. However, these models are not always adopted as they depend heavily on an appropriate choice of constitutive model and material parameters.   A preliminary load-deformation model of a 170m highwall in Solid Energy North (SEN) OperationsÆ Awaroa 4 opencast coal mine in the Rotowaro Coalfield has been prepared. This uses a strain-dependent constitutive model based on laboratory test results, strength parameters developed by SEN and excavation monitoring data. The laboratory testing has included triaxial compression tests on large-diameter fractured samples to characterise the stress-strain response of the closely-jointed soft rock masses that exist in many parts of the mine. Data from the monitoring of a 25m cut made during excavation of a haul road has been used to refine and verify the constitutive model. The resulting highwall model has predicted highwall crest movements corresponding to the excavation of each bench, for comparison with monitored values. Key model outputs are total horizontal movements of about 0.5m near the highwall crest and shear strains of 0.5-0.7% at the locations of potential bedding-parallel shear planes underlying the highwall. Most of the movement is expected to occur as creep rather than as an immediate response to excavation.

Jan 1, 2006