Search Documents

THE following notes simply sum up the writer's experience, which extended over a very busy period of some three years, dealing with wolfram ores and concentrates. The three methods for the estimation of tungsten that are discussed below are well known, but these results of their trials and comparison under technical conditions may be interesting. Method I. The routine procedure for the assay of rich wolfram ores or concentrates was as follows: Take 1 gram of finely-ground sample; digest with HCl and HNOs for about 2 hours, evaporating down to near dryness. To the remaining 5 cc., say, of liquid, add water, warm or boil for 1 to 1.5 hour, filter through a small filter paper, and wash the beaker and the insoluble matter with hot dilute HCl. It is best to keep the bulk of the insoluble matter (WOs, Si02, etc.) in the beaker at this stage. Then plaee a weighed porcelain dish under the filter funnel and wash the beaker and the filter paper with successive small quantities of strong NHOH, finally bringing all the insoluble matter on to the filter paper, and collecting the ammoniacal filtrates in the porcelain dish (S). Then place the filter paper with the insoluble matter in a porcelain crucible, dry and burn off the paper, cool, and brush the contents of the crucible on to an agate mortar, grind it to flour, and brush this back to the original beaker without loss. In the absence of draughts this can be done safely. Re-treat this residue with' acid and ammonia as above, running the second ammoniacal filtrate into the previous porcelain dish, which in the meantime has been heating on a water-bath.Finally evaporate to dryness on the water-bath the combined ammoniaeal filtrate, and then heat gradually to a red heat over a Bunsen burner, cool, and weigh. Then the contents of the porcelain dish give the WOs (tungstie aeid) direcvly (5).The final filter paper and insoluble matter may be ignited in a porcelain crucible, thus giving the "insoluble matter." If the ore...

Jan 1, 1922

The relevance of borehole and bore core evaluation to the design of underground coal mines is illustrated by considering the technical parameters of colliery design and the information from which they are constructed. The nature of this information is described, together with some methods for its storage, processing and presentation. Geophysical exploration techniques are compared as information sources. It is concluded that borehole and bore core evaluation is relevant and necessary for colliery design, but that optimum results will be obtained if drilling can be combined with geophysical techniques. Because of the inherent uncertainties in prediction of mining conditions the necessity of obtaining as much information as practicable from drilling evaluation is also stressed.

Jan 1, 1977

By A Logan, B Cuthbert

Brown and Chitombo (2007) indicated that during the last two decades, the international mining industry has been using mainly mass mining methods to extract safely and economically some of the important commodities such as copper, diamonds, gold, iron and nickel. Mass mining may be implemented either on the surface through large open pits or underground using mining methods such as sublevel, block and panel caving. Developments in the last ten years have demonstrated that caving methods can be applied successfully in strong orebodies at greater depths and in increasingly challenging geotechnical environments for which more traditional mining methods would be unsuitable, unsafe and/or uneconomic. These underground mass mining challenges require æfront endÆ investigation and analysis, robust engineering design and disciplined implementation and operation. Newcrest Mining Limited has focused its efforts on the development of gold/copper projects of substantial scale and margin. To help achieve this, the company is applying and further developing mass mining methods. These include large-scale open pits (OP) and underground mining methods such as sublevel (SLC), block (BC) and panel caving (PC). Block and panel caving now offer economies of scale opportunities for Newcrest to achieve high production rates at lower production costs; thus enabling the exploitation of mineral endowments at higher margins. This paper discusses the practical aspects of caving technologies that Newcrest continues to develop through its expertise at Telfer and Ridgeway SLC operations, Ridgeway Deeps BC and Cadia East PC projects.

Jan 1, 2008

By Hayes J. A

The satisfactory ventilation of an extensive coal mine is a subject which requires continual attention from all concerned.It must be remembered that a colliery contains many miles of workings, extending in all directions and throughout which noxious gases may be given off either naturally or by oxidation of the coal; fumes from explosives will be produced, dust will be gathered and carried in suspension, and water will be evaporated, producing a high humidity. Hence a considerable quantity of air in movement must be available to provide sufficient oxygen for men and horses, as well as to dilute and sweep away impurities, and maintain a tolerable degree of coolness.To maintain these conditions a modern colliery is divided up from the main ventilation shafts or adits (as the case may be) into a system of main airways, and in the working districts is further subdivided into district splits. To initiate the air movement, large centrifugal fans with a displacement capacity of up to 400,000 cu. ft. of air per minute are installed, generally in drifts off the upcast shaft, or adit, and at the return end of the ventilating circuit. These fans are thus exhausting fans and by producing a region of low density bring the heavier air at the other extremity of the circuit into movement to correct the difference in density, so far as it is not prevented by the frictional resistance of the airways. A flow of air is thus established, and it is obvious that to enable this volume of air to be as great as possible, the frictional resistance of the mine airways should be maintained at the lowest practicable figure. To this end, main airways should be as large as possible, have sides as smooth as practicable, and be straight, any necessary bends being of large radius.REQUIREMENTS OF THE VENTILATION SYSTEMThe New South Wales Coal Mines Regulation Act contains stringent provisions on requirements of the ventilation system. The main points are expressed in the following extracts:"In every mine which is in operation, unless a certificate of exemption from compliance with this rule has been granted by the Minister, whether any person employed therein shall be...

Jan 1, 1947

In the general planning of this area, provision was made for the distribution over the whole area as required of the following services:(a) Power and lighting from the substation distribution boards 'located in the winder house.(b) Miscellaneous electrical indicating, control and signalling systems.(c) Telephone lines from the main internal automatic exchange located in the changehouse, the town exchange to the automatic exchange and also direct lines from the town exchange to selected offices.(d) Compressed air from the incoming 16-in. air main. (e) Water, both unfiltered and filtered; and the disposal of the following effluents:(f) Sewage from the area to the town sewage system.(g) Changehouse shower water to the regeneration area.(h) Storm water to the general mine surface drainage system leading out to the naturally drained area north of the No. 8 Shaft.

Jan 1, 1957

By D Bradshaw

The recovery of molybdenum at Kennecott Utah Copper (KUC) has become increasingly important as its demand and price have risen dramatically in the last few years. Consequently, the flotation behaviour of the molybdenum bearing mineral, molybdenite, has received a significant amount of attention. The flotation performance of molybdenite generally lags that of the copper sulfide minerals and is much more variable. There are many factors including particle size, liberation, surface slimes and oxidation that contribute to this and also much speculation as to the relative contribution of each of these factors. This paper discusses the morphology of the molybdenite found at KUC, the mineral associations in the different lithogical ores types and the effect that each of these has on flotation performance. Quantitative mineralogical analysis and an assessment of particle shapes are used to explain that flotation behaviour does not necessarily follow expected trends and that some behaviour is counter-intuitive. This unique behaviour can be explained by the morphology and anisotropic nature of molybdenite.

Jan 1, 2008

This paper cites selected, prominent examples of current, major projects in Southern Africa in both the mining and civil fields. Differences and similarities in the life cycle of mining and civil projects are discussed. A closer relationship between the mining and civil fraternities is beginning to develop and should be encouraged because of the resultant exchange of experience and technology which benefits both disciplines. An attempt is made to assess future potential for new, major projects and trends in the implementation thereof.

Jan 1, 1999

The environment has emerged as a permanent component of Australia's socio-political context, intricately linked with personal and future security.The implication of this powerful new influence on the Australian Minerals and Energy Industry sector has been a plunging public image.

Jan 1, 1993

By D J. Black

Ventilation modelling is used to evaluate ventilation system performance. This paper describes modelling to assess potential changes to a single entry longwall ventilation circuit to improve ventilation and gas management. The longwall panel is extracting a 215 metre face in a 1.5 metre coal seam at a depth of 900 to 1000 metres below surface. The 1.5 metre B seam is located approximately 25 metres below the main 3.0 metre A seam and the gas content of both coal seams is approximately 20 to 25 m3/t. The B seam is extracted prior to the A seam and the mine relies on fracturing of the overlying strata to induce gas emission from the A seam to reduce the gas content prior to mining. Longwall operations in the B seam are constrained by limited ventilation and high gas emissions. Due in part to statutory limits on gas concentration and air velocity, the average longwall production rate is approximately 700 t per day.Gate roads in the B seam are single entry, developed using road headers and supported with steel arches. Additional timber cog support is installed to reduce roadway closure from abutment loading. Due to the slow advance of gate road development, mine management were reluctant to consider significant mine design changes, such as two heading gate roads; therefore, the investigation focused on determining the extent to which ventilation and gas emission impacted on longwall production performance, while recommending short-term, low-cost actions to improve ventilation and gas management to support increased longwall production.CITATION:Black, D J, 2017. Application of modelling to improve ventilation and gas management in a single-entry longwall panel, in Proceedings Australian Mine Vent Conference 2017, pp 239–244 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By Smith J. W, Hart G. N

Compositional and isotopic analyses of coal seam gases in the Southern Coalfields have shown that these gases frequently contain abnormally high concentrations of magmatically derived carbon dioxide. The size of this carbon dioxide reservoir and the extent of permeation of the sediments by carbon dioxide are not known.Therefore caution in evaluating the natural gas potential of the region is advised.

Jan 1, 1981

By R Garzon

For resources projects with healthy net present value (NPV) and low cash flow volatility, conventional discounted cash flow (DCF) analysis will continue to provide the dominant investment decision-making criteria. However, DCF analysis can be biased because it often applies a single risk-adjusted discount rate (RADR) to compare the value of projects with different risk characteristics. Many of the difficulties with DCF modelling arise from analystsÆ inability to determine appropriate risk discounts and to estimate expected spot prices inputs for the commodities produced over the life of the project. Modern asset pricing (MAP) is a very valuable complement to DCF analysis in addressing some of these issues. Most papers dealing with MAP, however, while academically rigorous, tend not to be explicit in terms of practical application of this methodology in routine project evaluation. This paper has the objective of reviewing the MAP methodology and of demystifying its complexity, by providing a simple but realistic step-by-step evaluation of a mining project, comparing its DCF and MAP NPV values. The paper concludes that MAP provides a minimum, risk-adjusted æfloorÆ value, thus representing a valuable complement to any DCF valuation.

Jan 1, 2007

One of the often overlooked factors affecting the capital investment decision in new or existing plants is the value of stock holdings necessary to maintain the plant. This paper puts forward a simple decision matrix on whether a part should be stocked depending on 1. the criticality of the item of equipment in terms of the effect on cash flow of its failure, 2. the lead time of the part, and 3. the stock holding value if it were Stocked.

Jan 1, 1986

By J Young, S Yu, P Moyo, M Powell, A Musunuri, B Bonfils, S Kanchibotla, P Yaroshak, V Jokovic

The appropriate design of liners continues to be an issue on many mills worldwide. Loss of milling capacity especially at liner change, uneven wear lives along the mill, substantial scrap on worn liners, excess mill down-time, undesirably short and unreliable wear lives are all common issues. This paper presents a designed approach to liner optimisation that follows a logical path of initial design and step-wise improvements based on liner wear monitoring. The target is to have a good liner design from start-up, then tune the profiles, heights and thicknesses based on wear monitoring. This is conducted as a team of liner specialist, site personnel and liner supplier. The application to the Pustynnoye SAG mill of JSC Altynalmas in Kazakhstan is presented. The increase in liner life by around 50% along with increased mill throughput of over 20% illustrate the huge benefit of the cooperative triumvirate approach through the gains that can be made in productivity and reduced liner costs.CITATION:Powell, M, Kanchibotla, S, Jokovic, V, Hilden, M, Bonfils, B, Musunuri, A, Moyo, P, Yu, S, Young, J, Yaroshak, P, Yalcin, E and Gorain, B, 2018. Advanced mine to mill application at the Barrick Cortez mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 177–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Yeliseyev AK, Shestakov AM

Comminution is the most power-intensive process in the technology for ferrous quartzite concentration. That is why improving comminution efficiency leads to the most appreciable economic effect on the concentration process. The trend towards reducing the lump size of crushed ore before charging the mill is considered to be of major importance in improving comminution efficiency. A considerable number of investigations have been performed in this direction. At the same time, a strong interest is also maintained in the increase of comminution efficiency due to optimisation of process taking place in the mill. Recently, investigations of the power intensity of the breaking process inside the mill have been carried out at the Krivoy Rog Mining Institute. It was ascertained that the routine conditions of comminution at a low mill ball charge ratio resulted in an unnecessarily high power consumption due to the force of impact of falling and milling bodies far exceeding the power required for comminution. For example, the power value for falling balls of 60 - 125 mm in diameter reaches 0.3 kNm, and the force and stress due to ball contact with the lining reaches 60 kN and 250 MPa respectively. These values exceed the force required for comminution by a factor of ten. Analysis of the mechanism of ore particle size reduction during comminution in the ball mill indicates that the size reduction is due to impact load, attrition load, and static load. The efficiency of size reduction is very low. During comminution in the ball mill, impact loads prevail and amount to 85 - 90 per cent of the total load. In this situation, not more than 10 - 15 per cent of destruction is due to attrition.

Jan 1, 1993

The Olympic Dam copper/uranium deposit was discovered in 1975 and subsequently commenced production in 1988 at a rate of 1.5 Mtpa using the sublevel open stoping mining method. In the following five years the operation underwent two optimisation programs that have increased mine output to the current rate of 3.4 Mtpa of ore. The pre-expansion requirements were annual development of approximately 10 000 m and the placement of around 500 000 m 3 /yr of cemented backfill. Previous to 1995 all hoisting was carried out by the Whenan shaft. The Robinson shaft was commissioned during that year to hoist increasing development mullock tonnages and to allow for increased ore hoist via the Whenan system. In 1996 WMC committed to expanding the output of the operation from 85 000 tpa (1996/97 budget) copper metal to 200 000tpa. The corresponding increase in mine ore production requires expansion to a nominal rate of 9.0 Mtpa. To achieve these increased tonnages, major hardware installations will include sinking of a third shaft capable of hoisting in excess of 9.5 Mtpa, a rail haulage horizon utilising automatic trains, expansion of the existing backfill plant to a production capacity of over 1.8 million m 3 /yr, increasing long term development rates to 15 000 m/yr and increasing the production drilling and blasting rates in line with the higher stope production output. This paper provides detail into the intended hardware (shafts, equipment, etc) of the mining system, and outlines the intended long-term operation and management of the operation. Of particular note is the background requirement of ensuring existing production targets are met to provide critical cashflows into the project during the period of expansion.

Jan 1, 1998

By Mckenzie CK, Scott A

The injection of coal as an auxiliary fuel in ironmaking blast furnaces has been introduced on many furnaces worldwide. This paper examines the present practice of coal injection and discusses future directions for the technology. This has been undertaken through the use of a heat and mass balance model which predicts the replacement rates of coke by coal and the effect of coal injection on blast furnace productivity. The results indicate that future pulverised coal injection could replace substantial quantities of metallurgical coke, but that the energy balance economics of individual steel plants will have a dominating influence on the future of the technology.

Jan 1, 1987

This paper talks about the experiences of groups we have worked with over the last few years in the Asia-Pacific region (Australia, Canada, New Zealand and Papua New Guinea) and the ways that they have worked to bridge the divide between traditional and introduced structures, governance at a regional level and the introduction of traditional values into monitoring and evaluation practices. In doing this these groups have created structures and processes which have helped them engage both more effectively with external stakeholders while maintaining the legitimacy of their own operations with their own constituents. These are important ideas for those involved in the mining industry that could provide a number of very tangible benefits to mining firms and their engagement with these kinds of groups.

Jan 1, 2009

By Hashimoto H, Arai Y, Sikong L

For utilization of solid carbonaceous materials produced in processes of cracking heavy oil, such as petroleum pitch, as powder fuel, it is necessary to develop a process for fine grinding of these materials. It is known that grinding' additives are effective for fine grinding of cohesive and heat-sensitive materials such as petroleum pitch, therefore in this study, effective methods for fine grinding of petroleum pitch with some grinding additives were investigated. Experiments were carried out by using comminution kinetics based on mass balance. From the results of the investigation by using a batch ball mill, it was found that sodium stearate, calcium stearate and carbon black were effective additives for the improvement of grinding efficiency. Optimum concentration of the grinding additives was also found to give a required particle size of products. Concerning to the action mechanism of these additives, it is considered that the additives which adhired to, or were absorbed on the surface of petroleum pitch particles not only prevented cohesion of the particles but improved dispersion of the particles as well. From the results of the investigation by using a laboratory screen mill which is a representative built-in classifiered impact crusher, carbon black was found to be an effective additive for the improvement of grinding efficiency and mill performance. It is also considered that the improvement of classification efficiency by carbon black affected the mill performance.

Jan 1, 1987

Distillation of the large and growing greenhouse literature indicates that: ò Global warming has occurred over the past century or more; ò Build-up of CO2 (and lesser greenhouse gases) in the atmosphere is a fact; ò This build-up is likely to cause further global warming. It does not appear possible to conclude that the observed C02 build up and observed global warming are linked; nor is it yet possible to forecast global or regional climate variation with conviction. The dominant greenhouse gas is C02 with about half the warming potential of those gases emitted by man's activities; and about 80% of anthropogenic C02 emissions are from the burning of fossil fuels. Fossil-fuel C02 emissions arg divided about equally between the developed countries of OECD and the rest of the world. However C02 output growth over the past decade was about 4% for OECD and some 40% elsewhere. Population growth and pressure for better living standards will ensure continued higher growth outside OECD. Uncertainty about the impact of increasing C02 emissions on climate, and the long lead-times involved in limiting the increase in atmospheric C02 concentrations, are good reasons for taking action now. Australia accounts for about 275 million tonnes a year or just over 1% of the CO2 emitted from the world's consumption of fossil fuels, and the fight to control global emissions will be won or lost elsewhere. Australia's participation will be by wise conselt and by example. In view of the uncertainties involved, it appears premature to take actions that might place an additional financial burden on our hard-pressed country. However, much can be done now that makes good economic sense and has the added benefit of limiting the growth in Australia's CO2 emissions. Natural gas emits less C02 per unit of energy when burned than either coal or oil. Furthermore, new gas-fired power stations utilise energy at considerably higher efficiency than is the case today with coal or oil. Because of much lower capital costs, there is a compelling economic case for permitting natural gas to compete freely with coal in the Australian power generation market.

Jan 1, 1989

Selection of the mining method and most appropriate mine layout for deep open cut coal mines is discussed, giving particular attention to the types of mines expected to be developed in the future in Australia. Because of the more complex nature of these operations a large number of alternatives for mine design are available, and the constraints associated with these designs are discussed. Potential problems to be overcome are identified to allow setting of realistic targets for maximum output and build-up production rates.

Jan 1, 1981