Search Documents

By G R. Hancock, D Verdon-Kidd, M J. Saynor, J B. C Lowry, T J. Coulthard

The ability to simulate the stability of post-mining landscapes over time scales ranging from decades to millennia is a critical element in the assessment of closure designs for uranium mines. Landscape Evolution Modelling (LEM) technologies provide a means to simulate and assess the long-term geomorphic stability of a conceptual rehabilitated landform for periods of thousands of years. However, a major issue with simulations derived from long-term modelling are the limitations associated with the data inputs. Specifically, simulations which utilise historic rainfall data only represent the variability of rainfall events that have occurred over a relatively short period. Consequently, these simulations run the risk of not accounting for the full range of rainfall variability that might be expected over an extended period of up to 10 000 years. Therefore, for this study a probabilistic approach was adopted to generate a stochastic synthetic rainfall data set to produce a series of unique rainfall scenarios, each representing a simulated period of 100 years. Importantly, utilising such an approach allows uncertainty in predictions to be better accounted for and provides a range or probability of likely outcomes.In this study, the effect of ten individual rainfall scenarios are assessed in terms of their impact on the predicted erosion and denudations rates produced by the CAESAR-Lisflood LEM for a conceptual rehabilitated landform of the Ranger Uranium Mine (RUM) in the Northern Territory of Australia, focusing on the Corridor Creek catchment (Figure 1). While legislation requires this site to be erosionally stable for at least 10 000 years (Commonwealth of Australia, 1987), here the focus is on the first one hundred years of landscape evolution, as this is the period in which erosion is expected to be higher, with limited vegetation cover or pedogenic development in the initial decades after rehabilitation. It is also the period where the drainage pattern is set.CITATION:Lowry, J B C, Verdon-Kidd, D, Hancock, G R, Saynor, M J and Coulthard, T J, 2016. Application of synthetic rainfall data to long-term modelling of a rehabilitated landform, in Proceedings Life-of-Mine 2016 Conference , pp 75–79 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

Synthetic seismograms of reflectivity method and some field records available are studied to detect the amplitude anomalies at the interface of the gaothermal reservoir the gas and/or oil boundary, and the underground tunnel. The first arrival of PO wave on the P-SV record are weak and emergent while those of P wave only rotated with respect to an incident angle are clear. This can, be explained by means of the energy loss of P-SV wave conversion. The primary reflections of P waves about depth fade away as compared to SH waves which do not perform any conversion, although they hold high attenuation in the fully saturated fluid layers. Reflection of comparable strength is present at the P-wave and S-wave... boundaries, but gas-saturated zones correlating with P wave bright spots do not show equivalent attenuation anomalies. Thus the comparative technique of P-SV wave and SI i wave records is very useful to indicate the strong amplitude anomalies at the boundaries of sealing targets.

Jan 1, 1990

By S Barrow, D Kent

Controlling the access of equipment, and people, has become more critical over the last few years for improving productivity and to meet safety responsibilities imposed by legislated obligations to have safety management systems. Hence Mine Site Technologies (MST) has spent the last three years completing the development of the tagging system to meet the mining industryÆs requirements, particularly streamlining access control. The basic tagging system tracks active Tags carried by personnel, or attached to vehicles and equipment, within underground zones. These Tags are detected (read) by Beacons placed strategically throughout the mine. As a Tag, or Tags, go past a Beacon they are read and the information transmitted back to the main database PC. This allows the current whereabouts of personnel and equipment to be known, as well as the history of their movements. The objectives of implementing the TRACKER Tagging System at Oaky No 1 Coal Mine were to: maintain a count of personnel inbye a particular point, and can alarm when a pre-set number is reached (eg the limit imposed by availability of SCSRÆs, etc); maintain a count of vehicles (and vehicle type) inbye a point, and can alarm if when a pre-set number is reached (eg when rated diesel units exceeds the limit for the ventilation present in that zone); manage the vehicle fleet, by keeping track of various vehicles underground better control and dispatch management of the equipment is achieved; keep track of equipment, knowing the location of equipment (such as forks, baskets, pumps, fans, etc) where last used or stored will minimise the risk of losing gear and assist in keeping inventory to a minimum; and locate personnel in emergency situations, by placing read Beacons throughout the mine the location of all personnel can be known in real time so that in the event of an emergency, their withdrawal can be monitored.

Jan 1, 2005

By Jianmin H, Shuqin L

This paper analyses problems associated with cement based technique in metal mines, and provides a new mining technique of packing the tailing sand and water into solidified material. In the new technique, the cementing agent is a solidifying material containing a high percentage of water and tailing sand. The sand and water solidify into the packed body at the same time. The slurry of the packed body varies widely in concentration and suitability for different mining conditions. It consists of two liquid materials, each composed of a cementing agent, tailing sand and water. The thick liquids are transported to the packing place at the same time. Their pumping property is good; they do not solidify or block up the pipe during transportation. At the packing place, the two liquids are evenly mixed.The mixed liquid flattens out well and its solidifying speed is so fast that it solidifies into a packed body within a very short period of time. The compressed strength of the packed body can reach 1.2-5MPa in one day, which satisfies the requirements of different mining conditions. By using the new mining technique, all the tailing sand can be used again in the packed body and it is low in cost and investment. The mechanisation is easy and thus the working efficiency is increased and the use of labour decreased. Contamination problems caused by i. Dr & Prof. Beijing Graduate School, China University of Mining Science and Technology,Beijing,China 2 Northern .Jiaotong University, Beijing,China 3. Beijing Graduate School, China University of Mining, Science and Technology

Jan 1, 1992

By W R. Adamson

Cerro Vanguardia SA (CVSA), property of AngloGold Ashanti, mines gold and silver from a system of vetiforme orebodies located in the south of the Argentine Patagonia, in the Province of Santa Cruz.Surface mining techniques are applied to develop a series of narrow pits with an average waste to ore ratio of 26:1. This quite unique constraint brings into focus the need to maximise inter-ramp and final wall angles, leading to a strong need to optimise wall control drilling and blasting in order to reduce back-break damage to an absolute minimum.The paper describes a program of applied investigation and design modification implemented during?2008?and?2009 in?two?separate pits of Cerro Vanguardia. Three distinct yet complementary damage mechanisms were identified and observed during the field components of the work; vibration induced strain fracturing, surface cratering around blasthole collars and quasi-static loading and unloading of the surrounding rock mass as a consequence of poorly controlled confinement.With these mechanisms identified, a measurement, modelling and modification campaign was conducted in order to reduce the incidence of each source of damage. Interactive design analysis and modelling, near-field vibration measurement, video capture and the application of electronic initiation technology were supported by seed wave modelling and topographic evaluation of the achieved results.Results point to the usefulness of simulation techniques for determining optimum delay timing to reduce vibration impact, while the visualisation of explosive energy distribution produced by drilling and explosive loading decisions assists in reducing the probability of over-confinement.This paper presents relevant aspects of the two fieldwork campaigns:1) describing the application of the techniques, and2) summarising the results obtained.

Nov 8, 2011

Application of the Anaconda Simplified Work Index for Multiple Test Sizes Vale uses Bond Work Index measurements extensively in a number of applications. The Bond Work Index is usually a good parameter for checking scale up procedures when sizing ball mills, as well as the basis for variability analysis whenever drill core data is available. It is typical to measure between 100 and 150 Bond Work Indexes, depending on the deposit characteristics. The Bond procedure is relatively complex and time costly. It also requires relatively large amounts of sample, which are very expensive to be obtained. The benefits of the Anaconda simplified procedure are: considerably smaller sample requirements and laboratory time. This makes it very much attractive at Vale's development centre, including geometallurgical mapping, operation efficiency control, mine to mill, etc. The Anaconda simplified procedure was implemented and evaluated at Vale's Development Centre using a number of ores and several samples of each ore totalling more than 190 measurements. The Anaconda simplified method was calibrated for several test sieves and a correlation for any test size was determined for Vale's test mill. The calibration was also extended for two sample top sizes. The relative error of the simplified procedure was found to be in the range of nine per cent which is within the expected error Bond standard procedure. The implementation of the Anaconda method at Vale's development center has been used with great success over the past years in several green field, brown field projects and operating plants.

Sep 13, 2010

By Hamilton LH, Campbell PB

Since fundamental research in applied coal petrography is carried out mostly on polished surfaces, backscattered electron microscopy is most applicable for studying coal in the SEM. By employing this technique coal macerals can be easily identified , and information on the relations between maceral groups, mineral matter and trace elements are highlighted by grey level contrasts. This type of information is valuable in coal technology and cannot by normally revealed by the light microscopy (e.g. the distribution of inherent mineral matter).

Jan 1, 1989

By Williams D. J

The boundary element method is one of a number of tools that have found wide application in geomechanics for mine design and stress analysis. Two examples are presented in this paper, illustrating the use of the boundary element method to find potential problem regions in large-scale excavations. These examples are from a Papua New Guinea open cut mine and an Australian sub-level caving operation. Because of the scale of the mines and the complexity of the excavations, the boundary element method is the only practical numerical modelling technique to account for the major influences. Although the boundary element method uses only linear elastic models of the rock mass, the paper illustrates techniques for dealing with non-homogenous and anisotropic rock masses, as well as clasto-plastic effects associated with an excavation.

Jan 1, 1995

By N Khalili, J Zhao, G F. Zhao

Toppling failure of a jointed rock slope was studied by using the distinct lattice spring model (DLSM). Compared with the classical discrete element model, the DLSM has the advantages of free calibration of micro-mechanical parameters and easy to represent discontinuities, and is more computationally efficient. In this work, the DLSM was used to investigate the toppling failure of jointed rock slopes. The numerical simulation was verified against experimental data from a centrifuge model test on a jointed rock slope. Both the horizontal deformations and failure pattern observed in the centrifuge test were reasonably reproduced using the DLSM. Then, the mechanism of the flexural toppling failure was studied numerically by using a parameter analysis. Finally, some insights were derived that may be useful for practical engineering.CITATION:Zhao, G F, Khalili, N and Zhao, J, 2014. Application of the distinct lattice spring model on toppling failure of a jointed rock slope, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 207–214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By J Jasper, L Koroznikova, J Begelhole

This paper outlines a comparison of heavy liquid and heavy suspension separation methods for iron ore characterisation.As part of Arrium MiningÆs program to improve its knowledge of ore types being processed in its two hematite ore beneficiation plants (OBP), metallurgical evaluation of hematite feed for the upgrading process has become a major focus.Iron ore deposits almost always contain more than one valuable (and relatively dense) iron mineral. Iron ores are found with a range of iron contents, giving rise to density variations.At present the industry relies on heavy liquid separation techniques for the evaluation of iron ore samples arising from exploration, mining or metallurgical processes. There are only a few high-density liquids available, which are both high-cost and highly toxic.Low-toxicity solutions that can be utilised at relative densities up to 3.0 have been developed. However, highly-toxic organic liquids are required presently to achieve relative densities beyond 3.0.Bromoform which has a specific gravity (SG) of 2.89, and diiodomethane (SG 3.31) are commonly used; both present significant health and safety hazards.æClericiÆs solutionÆ (mixtures of thallium formate and thallium malonate) provide liquids having specific gravities between 4.0 and 5.0. ClericiÆs solution is highly toxic and testing is currently conducted by a limited number of laboratories worldwide.An alternative to ClericiÆs solution and organic liquids is a low-toxicity, high-SG, suspension technique, which has been demonstrated successfully for heavy mineral sands. This heavy suspension method employs mixtures of fine tungsten carbide particles in lithium heteropolytungstate (LST) solutions.Heavy liquid separation is not commonly used as part of routine iron ore feed characterisation due to the expensive, toxic and time consuming nature of the technique. Our results show that the heavy suspensions method can achieve low-cost, low-toxic separation and are outlined and results compared with results using ClericiÆs solution presented.Heavy suspension technique provides a theoretical/absolute separation of a particular sample. By placing an iron ore sample in a suspension of a particular density, it produces two products: a sink fraction and a float fraction. As iron oxides-hydroxyoxides are denser than the gangue minerals associated with the ore, particles that have high iron content will sink and the particles with gangue association will float. This process is repeated over several densities, thus also enabling separation of the constituent iron ore phases. A theoretical grade and a theoretical mass recovery can be calculated. With these calculations, a grade-mass recovery curve can be constructed for any element that is of interest.This type of characterisation can be used to either prepare OBP feed-piles of known processing characteristics, or to benchmark the performance of the process against what can be theoretically achieved on a continuous basis.CITATION:Begelhole, J, Jasper, J and Koroznikova, L, 2013. Application of the heavy suspension technique for ore beneficiation plant feed characterisation from the Southern Middleback Ranges, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 269-278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By B Cronin, M Gao, M F. Young

Fine grinding technology has become extremely important for Mount Isa Mines Limited in the last decade for flowsheet development for the McArthur River deposit and in rejuvenating the Lead-Zinc Concentrator at Mount Isa. Regrinding products with 80 per cent passing seven microns and 12 microns were required, respectively, for the McArthur River ore and the Lead-Zinc Concentrator at Mount Isa. Development of the ISAMILL, a horizontal stirred mill with a gross mill volume of 4000 litres (a net volume of 3000 litres), has been successful in delivering the required grinding product sizes with an energy consumption acceptable to a mining operation. The ISAMILL performance for processing both lead and zinc streams at Mount Isa is discussed in this paper, including the milling energy efficiency, the media wear and the size-by-size recovery data for one flotation process following the fine regrinding stage. The potential use of the ISAMILL technology at various phases of the mining cycle is also discussed.

Jan 1, 1998

Getting it right is a very profitable outcome. Shareholders would ideally like to see their directors get it right all the time on the major economic decisions. But it is very difficult for mining directors to get it right all the time in such an uncertain environment. Primary decision-makers of companies with significant stakes in the mining industry should get it right much more frequently. The legal measures of evidence (beyond reasonable doubt and on the balance of probabilities) can be used to determine whether grade estimates (a key revenue variable) are realistic. The application of this approach can be far reaching. More frequently correct decision-making would result in more effective allocation of limited resources (capital and labour). In turn, this would result in higher financial returns and a more extensive mining industry.

Jan 1, 1994

By Ryan CG, Cousens DR, Sie SH, Suter GF

Proton microprobe analyses of trace elements have been carried out on a wide variety of ilmenites, garnets and chromites, to improve diamond exploration methods. The results so far show the potential to discriminate between barren and diamondiferous source rocks, and to distinguish multiple sources within single Drainages.

Jan 1, 1989

By Ryan CG, Ramsden AR, Sie SH, French DH, Griffin WL

Proton microprobe and electron microprobe analysis are being used in combination for in situ determination of the trace element contents of oxide, sulphide and silicate minerals in a sample of the Merensky Reef. Initial results indicate that chromites contain only Ni, Zn, Ga, Zr ar d Nb. Platinum-group elements, if present, are at concentrations less than 2 to 6ppm. Ru, Rh and Pd are the only platinum group elements to be consistently detected in the sulphides. PentLindite is the most important host for these elements with the concentration of these elements being dependant upon the mineral association in which it occurs

Jan 1, 1989

Callide Coalfields produces a sub-bituminous, very subhydrous, low rank, steaming coal with good combustion properties, primarily for domestic power generation. Geological input into planning of coal extraction requires expedient production of detailed structural, lithological, analytical, geophysical and geotechnical data. The CSIRO-developed SIROLOG borehole logging software and hardware system allows for detailed spectrometric analysis of coal/interburden. The gamma-gamma and neutron-gamma SIROLOG techniques both provide improved prediction of ash content over other borehole techniques. The neutron-gamma technique also predicts density and some important ash constituents (especially iron, alumina and silica). The software/hardware configuration allows for quick, easy interpretation of coal seam depth and lithology, parting thickness and ash/ash constituent contents immediately after a borehole has been logged. Within certain mine areas in the Callide Basin, the iron content of mined coal is widely variable in both vertical and lateral extent within and between seams. This variability creates problems in predicting the slagging behaviour of æas-receivedÆ coal during combustion, especially where the iron content of the ash exceeds 19 per cent. Using the SIROLOG tool in co-operation with traditional borehole sample laboratory analysis results, patterns in this variability can be determined and related to geological properties and process of formation of the coal seams. Subsequently, areas of high iron can be predicted in advance of mining. Since 1992, on-going collection and interpretation of SIROLOG downhole geophysical log data has significantly contributed to a number of research projects related to gaining a preliminary understanding of the iron distribution and formation during the Coal MeasuresÆ deposition. Because the probe was able to record variations in coal mineral matter content, it was found to complement more conventional techniques such as reflected light petrography, X-Ray Diffraction and SEM techniques that examine the mineralogy of iron species. Additionally, software has been developed to allow integration of SIROLOG data into existing geology databases, enhancing coal quality modelling and daily prediction of parameters such as raw ash, silica and iron contents that are indicators of ash fusion propensity. The correlation of SIROLOG-derived iron geophysical traces between drillholes and other sample points highlighted lithological and structural controls in the iron distribution in the sequence previously not detected. This work has allowed the development of a methodology for predicting iron in advance of mining and reconciling as-sold coal quality to that predicted. Predictions are currently being assessed at the coal face as mining progresses through high-iron zones.

Jan 1, 2000

By M S. Gallagher

In todayÆs high tech world, systems are getting bigger, faster, better. To remain at the leading edge, in any business, depends on accuratebut flexible design thereby allowing operational managers to providealternatives to improve their operations. The ultimate goal is to deliver to plan, with optimum economics. Mining is no different; with falling prices and escalating costs,improved margins become the focal objective. There are many ways toachieve this, ranging from operational efficiency improvements through production scenarios to planning initiatives. Of all, planning usually receives the least attention, yet it is the area of most influence on the Net Present Value (NPV) of the reserve. With computer technology, numerous concepts and iterations are possible thereby closing the gap between optimal and actual design. This paper discusses the application of the split shell design at the De Beers Venetia open pit in South Africa.

Jan 1, 2001

By T Elkington, A Finch

The theory of constraints (TOC) is a business improvement method that focuses on exploiting a business’s bottleneck to deliver the highest possible profit. Early applications were mostly in the manufacturing industry; however, the theory in itself is completely generic and has now been applied widely in other industries such as services, retail, software and distribution, amongst others. The intent of the approach is attractive – it focuses on the ‘silver bullet’ rather than ‘death by a hundred projects’, and it focuses on growth rather than cost cutting. Application within the mining industry has been limited to date, although there are a few applications emerging. This paper discusses how TOC can be applied to maximise value during the project planning phase and how to maximise profits when the mine is operational. The paper uses two case studies to illustrate the approach. Case study 1 uses the approach to improve tactical mine planning, which delivers an increase in revenue of 58 per cent. The second case study is a strategic mine planning example that delivers an increase in value of 77 per cent.CITATION:Finch, A and Elkington, T, 2014. Application of the theory of constraints to strategic and tactical mine planning, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 129–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Mishra S. N, Mishra R, Sen P. K

Control of silicon in produced through the submerged-arc furnace can result in reduced power and coke consumption in addition to improving the quality of the hot metal. A thermo-chemical analysis of the production of ferro-chromium was carried out to devise strategies to control the recovery of silicon during the manufacture of ferro-chromium. The presence of three thermochemical zones in the furnace with respect to the reduction of silica was recognised from this analysis. Any strategy for the control of silicon recovery has to take cognizance of these thermochemical zones. The effect of various strategies on the silicon level in the hot metal have been evaluated. Possible strategies, such as the reduction of coke level in the charge; the replacement of quartz; pre-reduction of the ore and the control of the temperature profile are discussed in this paper.

Jan 1, 1999

By D Hope, D K. Mukhopadhyay, J D. Harvey

South32 (S32), a globally diversified mining and metals company, is listed on securities exchanges around the world (ASX, JSE, LSE), with its primary listing being on the Australian Securities Exchange (ASX). Chapter 5 of the ASX Listing Rules (Australian Securities Exchange (ASX), 2019b) requires a mining entity to provide a summary of governance arrangements and internal controls with respect to its estimation processes, estimates and reporting of Mineral Resources and Ore Reserves annually. As a global company, it is also important to design and implement all governance processes and internal controls which can be used consistently across the organisation. The three lines model (previously known as the ‘three lines of defense’ model) is employed across South32 to manage risk where the first line (Practitioners) designs, implements and executes processes and controls to manage risk; the second line (Stewardship) identifies material gaps and improvement opportunities in the first line by monitoring conformance with the group requirements, legislative and regulatory obligations. Second line also assists with the development and improvement of core fundamentals based on industry good practise. The third line (Group Assurance) provides independent and objective assurance over the Group’s system of risk management and control. The estimation of resources and reserves for most of the operations within South32 is managed by the Planning function. The estimation process is part of the annual Life of Operation Plan (LoOP). The LoOP identifies and assesses the strategic alternatives for the development of an operation and recommends the preferred pathway based on value and risk. The LoOP starts with opportunity framing and the updated resources as an input and ends with the short-term plan and annual budget (the outputs). Ore Reserves estimates are one of the outputs from the LoOP. All the inputs and outputs follow internal standards and procedures which includes peer review and performance reconciliation. Stewardship (Second line) which is a centralised function has standards in place to ensure compliance to internal controls and external regulatory requirements. This includes assessment of the competence of Competent Persons, technical reviews, independent audits and training in the relevant chapters of the ASX Listing Rules, Guidance Notes and Appendices. Group Assurance (Third line) which reports to the Risk and Audit Committee of the Board of Directors ensures the design and operating effectiveness of the processes, standards and procedures associated with the estimation and reporting of resources and reserves. While the level of scrutiny has a different intent for each line in the three lines model, the overall purpose is to achieve a consistent outcome across the organisation

May 24, 2023

By Kam KM, Tran B

Statistical techniques of Box and Jenkins (1976) have been used to assess the existing control schemes and determine the dynamics of flash smelting furnace at the Kalgoorlie Nickel Smelter. Pertinent process variables, such as, oxygen flow, flux flow, matte grade and iron to silica ratio in slag, were considered in the analysis using routine operating data collected over two periods of operation. Results indicate inadequate control of some of the important variables. Dynamic characteristic parameters (dead time and response time) between a set of input and output variables were identified to improve optimisation of the existing thermodynamic model used for flash furnace control.

Jan 1, 1996