Search Documents

By T. M. Anderson

From the start of production in 1915 until 1948, underground block caving operations accounted for all of the ore production of Inspiration Consolidated Copper Co. Open pit development work began in 1947, and ore production from the open pit commenced in March 1948. Thus began the transition from underground to open pit mining which continued until August 1954. Since then, open pit mining has accounted for all ore production which presently averages 105,000 tons of ore and 75,000 tons of waste rock each week. Open pit mining operations at Inspiration is carried on in two separate pits-the Live Oak Pit and the Thornton Pit. The Live Oak Pit covers an area of approximately 1500x3000 ft and the Thornton Pit, 2500x2000 ft. The geographic centers of the two pits are 4000 ft apart and, at their nearest point, the surface slopes are 500 ft apart.

Jan 1, 1961

H. A. SCHWARTZ, ? Indianapolis, Inc. (written discussion§).-Re-ferring to the very interesting paper on the graphitization of white cast iron, the writer desires to present certain facts and conclusions, entirely, in harmony with those of the authors but which may he not without interest as furnishing additional evidence upon the same subject. The graphitization of white cast iron, being the basis of malleable

Jan 10, 1919

By C. H. Wayman, D. W. Fuerstenau

THE gas phase is one of the indispensible ingredients in flotation operations. Flotation depends on the collision of an air bubble and a mineral particle in a pulp and their ability to remain in contact long enough for adherence to take place. Before it is possible to understand the mechanics of air bubble-mineral particle encounter, it is necessary to learn more about the nature of bubbles themselves before collision with a mineral particle has taken place. To date, little work has been done on air bubbles in flotation systems. In 1945 Fahrenwald1 presented a study of the role of frothers on air bubbles and on aeration in flotation, and recently Wark and Sutherland2 discussed the work of Rosenberg3 in relation to flotation. The research reported in this present article was undertaken to investigate systematically the effect of bubble size and the concentration of certain reagents on the terminal velocity, shape, path, and drag coefficient of single bubbles in distilled water. Most of the work is concerned with the effect of a-terpineol on bubble motion in water, but studies were made with potassium chloride, potassium hydroxide, potassium ethyl xanthate, and potassium amyl xanthate.

Jan 6, 1958

By T. Guilford Smith

In presenting the subject of " Armored Turrets for Coast Defense " to this Institute, I am indebted to the Gruson Ironworks, a company incorporated under the laws of the State of New York, for valuable information, model and plans, by which I hope to make clear the construction and peculiar merits of this class of gun-protection. I wish it understood, however, that this is not an undeveloped and untried inventor's ideal, but an advanced and fully perfected system, which has long since passed the experimental stage and has been adopted by most of the foreign governments, after years of extensive experimenting and the expenditure of millions of dollars. The present seems an appropriate time to present the matter to the scientific public, since, for the first time, it is possible to produce these turrets in this country, of American material, and made by American workmen, owing to an agreement entered into between the Gruson Iron-works and the Fried. Krupp Grusonwerk, of Magdeburg-Buckau, Germany, where they have hitherto alone been manufactured. Although its full development and present perfection have been attained at the German works, it may be of historic interest to state that the first idea of using a rotating protected platform for large guns originated with Mr. Theo. Ruggles Timby, a native of the State of New York, who filed a caveat in 1843 for a " metallic revolving fort, to be used on land or water, and to be revolved by propelling engines located within the same and acting upon suitable mechanism." This was followed in 1862 by the issuance to Mr. Timby of two patents (No. 35,846 and No. 36,593) covering the ideas described in his caveat of 1843. The first practical application of this system was made on the " Monitor," of Civil War fame, Mr. Timby receiving $10,000 for two

Jan 1, 1901

By David Sinclair, Philip B. Bucky

THE dimensions and shapes of mine structures may at present be determined by (1) field experience, (2) structural calculations, and (3) barodynamic tests.§ None of these, however, provide information as to the stresses, their direction and distribution in a mine structure. For the design of pillars, the placing of openings relative to working places such as gangways, haulage levels, etc., this information is desirable. Photoelastic methods provide this and, while relatively new, their application in all engineering fields is assuming increasing importance. This paper, therefore, will present the method with a few applications to mining, and with sufficient reference for further study by the reader. PART I THE PHOTOELASTIC METHOD The photoelastic method of stress measurement determines the stress distribution in a two-dimensional model by optical means. It makes use of the fact that when a piece of isotropic transparent material, such as glass, celluloid, or Bakelite, is stressed and viewed in polarized** light a picture is seen which indicates by its color bands of light, or fringes, the magnitude of the stresses, their direction and their distribution. GENERAL EXPLANATION The stress at any point 0 in a structure (Fig. 1), may be resolved into two components, P and Q, each a pure tension or compression, at right angles to each other, called principal stresses.1 To fully identify the stress, the values of P and Q and their directions or angle [0] must be known.

Jan 1, 1940

By M. B. Mirza, F. D. Wright

Models of photoelastic material were made to simulate a mine roof that had cracked over the edge of the pillars and at the center of the span. Models were restrained from moving laterally outward so they acted as flat arches. Uniform loading was approximated by loading the models along the bottom at eight points spaced equally along the span. It was found that for models with depth to span ratios of 1:3 to 1:6, the maximum stress at the top of the center crack could be calculated directly by the following formula: Elastic stresses in mine roofs composed of sedimentary beds are usually computed by assuming that the immediate roof bed acts as a fully restrained beam uniformly loaded by its own weight and by overlying strata. Very little work has been done to analyze stresses in roof beds or beams which contain vertical (normal to the span) or nearly vertical cracks. Yet every mining engineer has walked safely under roofs that show such cracks. As far back as 1933, Bucky' made model studies of the effect of vertical cracks on the behavior of horizontal strata. He did not make any analysis of the stresses but did show that a cracked beam will stand safely under certain conditions, and also showed that a beam restrained at the ends can crack over the supports and in the middle without collapsing as long as the ends of the beam are not free to move laterally outward. The beam, or rather, part of the beam, acts like a flat arch and supports itself by pushing outward at its supports. In 1941 Evans2 treated analytically the problem of a beam cracked along so many planes perpendicular to the axis of the beam that no tensile stress can operate. He named this type of beam a "voussoir-beam" by analogy to the voussoir-arch. In 1962 ~a~cocks~ modified Evans's solution by including the effect of the shear stress component of the resultant force at the abutment. This paper gives the results of a photoelastic study of the stresses in a beam containing vertical cracks in the center of the span and over the supports. A

Jan 1, 1963

By F. M. Doyle-Garner, A. J. Monhemius

Hydrolytic stripping is the process whereby metal ions in a loaded solvent extractant are hydrolyzed by water, typically at 130°C to 200°C (265°F to 392°F). Equilibrium hydrolytic stripping tests were done on Versatic 10 solutions containing various metals, singly and in mixtures. Single solutions of Fe, Ni, Cu, Mg, and Mn precipitated [a]Fe2O3 Ni(OH)2 Cu2O + CuO, Mg(OH)2 and [?]Mn203 respectively, during hydrolytic stripping. Several mixtures containing iron precipitated magnetic spinel ferrites, MFe204. No other combinations formed mixed oxides. It is proposed that the mechanisms for hydrolysis and precipitation of iron in loaded Versatic solutions are similar to those for iron hydrolysis in aqueous solutions. Magnetic interactions between mixed carboxylate complexes are thought to be responsible for the homogenous nucleation of magnetic mixed oxides in preference to single oxides.

Jan 1, 1986

By Richard S. Culver

In spite of the widespread interest in rock bolt research, relatively little is known about the critical region surrounding the bolt anchor. In analyzing the stress distribution around an opening resulting from rock bolt support, it is commonly assumed that the bolt is fixed at a point far enough from the surface so that the anchor does not influence the performance of the bolt. Furthermore, a bolt anchor is assumed to per- form satisfactorily if it will hold the design load with a minimum amount of load relaxation, commonly called bleedoff. From the standpoint of the design engineer both of these assumptions are reasonable, but they ignore the fact that the extremely high stresses in the region of the anchor are capable of generating fractures in the rock. Lang1 estimated the bearing stresses for a slot and wedge anchor on a one-inch-diameter bolt to be as high as 125,000 psi. This paper describes a more thorough analysis of the magnitude of the stresses around the anchor and the nature of the potential fractures that might result. It should be emphasized that there are two types of anchor-associated fracturing which may occur. The more common form, particularly in soft rock, is severe localized crushing of the rock in the immediate vicinity of the anchor, which makes securing the anchor difficult and causes bleed- off. It is also possible to develop larger single fractures which propagate out from the anchor, affecting the strength of the entire rock mass. The formation of these larger fractures is of primary concern in this paper. In addition to estimating the contact stresses and pullout load for slot and wedge bolt anchors, Lang carried out an important study of rock bolt interaction which served as a basis for the experimental phase of this investigation. In the first phase of his tests, a plate of photoelastic plastic was compressed by a row of piano wire bolts, simulating the interaction of bolt stress fields to form a zone of uniform compression (Fig 1). To show the supporting effect of this beam, hr carried out another test series

Jan 1, 1968

The Committee on Valuation of the American Electric Railway Association, has had compiled a "Bibliography on Valuation of Public Utilities." The work was done by the library force of the American Society of Civil Engineers, and brings up to Dec. 23, 1915; a bibliography issued by the American Society of Civil Engineers on May 15, 1912. The Bibliography has been printed -and issued by the American Electric Railway Association, 8 West 40th Street, New York, N. Y., and may be obtained from its Secretary on the payment of 50 c. References are arranged under the following headings: General, Electric Light and Power, Gas Works, Mining, Railroads, Steam Power, Street and Inter-urban Railways, Telegraph and Telephone., Water Power, Water Works. References are given to the principal technical publications, to various works on the question, of valuation, to rules and regulations of Commissions and other official bodies, and to the proceedings of various societies. Undoubtedly the compilation is the most comprehensive that has yet been published.

Jan 7, 1916

By Albert Sauveur

(New York Meeting, February, 1913.) IT is delightful to read a technical paper like that of J. E. Johnson, The Effect of High Carbon on the Quality of Charcoal-Iron, presented in October, 1912, at the Cleveland meeting of the American Institute of Mining Engineers.1 The clear, simple, and straightforward manner in which he describes his experiments and results makes you feel as if you had been, so to speak, at his elbow during the course of his investigations, while his method of procedure is so rational that you can fairly anticipate each step in the logical sequence of the tests performed. The following notes suggested by Mr. Johnson's paper are presented here in the hope that they may help, if only a mite, towards the final solution of a problem of considerable scientific and industrial importance.

Jan 3, 1913

By Howard Martens, Pol Duwez

XPERIMENTS were performed on a Cr-Fc alloy Econtaining 44.7 pet Cr in order to determine the heat evolved during the transformation of the a solid solution into the s phase, and the change in volume accompanying the transformation. Since previous measurements on the rate of formation of a from s indicated that the reaction was quite fast as soon as the equilibrium temperature of 820°C was exceeded by some 50°, standard thermal analysis experiments were performed on heating specimens of s at the rate of approximately 40°C per sec. A definite thermal arrest was observed at 870"C, Fig. 1. This result indicates that the reverse seaction of into a is exothermic. From the heating curve of Fig. 1, taking 15°C per sec as the heating rate in the neighborhood of the transformation, 2.4 sec as the time for transformation, and assuming that the specific heat of the alloy at 850°C is an average between iron and chromium, namely 9.5 cal per mol per "C, the latent heat of transformation is approximately 342 cal per mol. The order of magnitude of this latent heat was also obtained by comparing the heating curve of Fig. 1 with a similar curve obtained with pure iron under identical experimental conditions. It was found that the length of the thermal arrest for s was about 1.8 times as long as that for iron. Since the latent heat of the a to 7 iron transformation is 203 cal per mol1, 2 the latent heat of it to a would be 365 cal per mol, which is in relatively good agreement with the value determined from the heating curve. For the determination of volume change, thermal expansion curves were recorded using a specimen containing 44.7 pet Cr and completely transformed to cr by previous treatment. The curves were recorded at a rate of heating of about 4°C per min and at approximately 840°C a sharr, increase in length of about 0.08 pet took place. Fig. 2. It is therefore established that the specific volume of a near the transformation temperature is about 0.24 pet smaller than that of a, and consequently, when the s phase forms in an a matrix, it would tend to shrink away from the matrix. Since the s phase is known to be extremely brittle, these results offer an explanation for the microscopic cracks often observed in the a phase under the microscope. The results of this study are in qualitative agreement with previously published data on stainless steel 19-9DLa and on a Cr-Fe alloy containing 45 pet Cr.' The increase in density due to the transformation from n to s given in ref. 4 is 0.90 pet. These measurements, however, were made at room temperature. whereas the presently reported 0.24 pet is the change at the temperature at which the transformation takes place during heating. In the graph of Fig. 2, the percentage change in length that would be observed at room temperature is given by the length X, which is about 0.27 pet. This would correspond to 0.81 pet in volume change. Acknowledgment This work was done at the Jet Propulsion Laboratory, California Institute of Technology, under Contract No. DA-04-495-ORD-18 with the Army Ordnance Corps, Washington, D. C. The authors wish to thank this agency for permission to publish the results of this investigation. References I H. Klinkhardt: Measurements of True Specific Heats at High Temperatures. Annalen der Physik (1927) 84, pp. 167-200. - H. Esser and W. Runghardt: Influence of the Method, of Dctcrmination on the Measured Heat Content of Iron. Archtvo ffur Dct Eisenhiittenwesen 11934) 8, pp. 37-38. J. J. Gilman, P. K. Koh, and 0. Zmeskal. Delta Ferrite Formation and its influence on the Formation of Sigma in a Wrought Heat Resisting Steel. Trans. ASM 1 1949) 11, pp. 1371-1388. 1 J. M. Thomas: Discussion of ref. 3. Trans. ASM (1949) 41, pp. 3 390-1392.

Jan 1, 1957

Jan 1, 1967

By C. W. Hill, G. P. Luckey

In a previous article1 preliminary experiments were described, indicating the possibilities of a quantitative spectroscopic method for the determination of small amounts of lead in copper, which would be accurate and rapid, and could be carried out in the refining plant by one not skilled in chemical analysis. The present paper deals with the development of the method in the factory, giving the details of apparatus and its standardization, and presenting a comparison of the accuracy of the method with that of the standard electrolytic determination. (For variations and other applications of the method, the reader is referred to the first article.) A carefully weighed sample (0.4 gm.) of the copper to be tested is placed in a cavity in a graphite positive electrode. An arc capable of

Jan 1, 1919

By C. E. Schwab

A lead-zinc orebody, in fairly strong quartzite and with a dip of 35° to 60°, is block-caved by use of scrams in a stair-step pattern up the ore footwall. Scram linings to handle coarse muck and permit the use of folding scrapers are developed by the use of end-grain wooden blocks to reduce maintenance and keep operating cost to a minimum.

Jan 10, 1953

By S. J. McCarroll

Fig. 1—The belt shown at right carries filter cake to mixing station over calciner. Crude ore conveyors appear in right background. THE Three Kids mine, some six miles east of Henderson, Nev., is in a typical southwest desert area, with high dry summer heat and cool to cold winter seasons. The manganese deposit was located during World War I.' During this period 15,000 to 20,000 tons of ore assaying up to 41 pct manganese were shipped. Interest in the deposit was not revived until the middle thirties, when experiments on the ore were initiated. Test work indicated possible recovery of only 70 pct by flotation, but in 1941 additional work was done at the Boulder City pilot plant of the U. S. Bureau of Mines and also by M. A. Hanna Co. As a result, the Manganese Ore Co. was formed and a plant utilizing the SO2 process was constructed. Numerous operation difficulties ensued, and the plant. was closed when the manganese situation in the country eased. In 1949 Hewitt S. West initiated negotiations to acquire the plant. In 1951 Manganese, Inc., was formed and contract entered into with the General Services Administration to supply 27 million units of metallurgical grade manganese in the form of nodules to the national stockpile. A second contract was made to upgrade 285,000 tons of stockpile ore. Test work was undertaken by the Southwestern Engineering Co. and likewise by the Boulder City pilot plant at the U. S. Bureau of Mines. Results obtained indicated the commercial feasibility of the flotation process. Construction of the plant, which is shown in Figs. 1 and 2, was started in June 1951, and operations on a break-in basis began in September 1952. Apart from the usual starting difficulties two major disasters caused serious setbacks, one a kiln failure in February 1953, and the other a fire that destroyed the flotation building in June of the same year. The nodulizing section of the plant resumed operation in November, and the flotation section in January 1954. The ore minerals are chiefly wad,* with minor amounts of psilomelane, and occur in sedimentary beds of volcanic tuff. The ore is overlain with beds of gypsum which outcrop or may be covered with surface gravel. Intermediate beds of red and white tuff occur frequently with lenses of red and green jasper and stringers of gypsum and calcite. Small amounts of iron are present; lead content averages about 1.0 pct and minute amounts of copper and zinc are found. Barite, celestite, and bentonite are present. Since these are made up of minute asicular crystals, moisture content is very high, averaging about 18 pct. Ore reserves have been estimated at 3 million tons averaging 18 pct Mn2 and up to 5 million tons after grade is dropped to 10 pct Mn. A good part of the orebody was stripped of overburden by the previous operating company . Approximately 50 pct of the ore, representing more than 60 pct of the manganese, can be mined by open-cut methods. A system for underground min- . ing has not yet been decided on. Open-cut mining with benches of 20 ft has proved satisfactory. Although the ore is soft and appears dry and dusty it has a certain resilience, probably due to the porosity and moisture which makes drilling and fragmentation difficult. Wagon drills have been abandoned in favor of the Joy 225-A rotary drill which will put down a 43/4 -in. hole at the rate of 2 ft per min. Holes are spaced in a pattern with 8 to 9-ft centers. Forty percent powder has been used, but better breaking to 2-ft size is obtained with low velocity bag powder of 30 pct strength. Loading is done with one 21/2-yd shovel, and cleanup follows with one D-7 bulldozer. The ore is hauled with Euclid trucks about 1000 ft from the pit to a blending pile, where the daily mine production is spread in layers by bulldozing until approximately one month's mill feed is accumulated. A new pile is then started and mill feed is drawn from the first pile by one 13/4-yd shovel and Euclid trucks, with a haul of approximately 500 ft. Mining is performed by an independent contractor with engineering and supervision by the company staff. Early test work indicated that the manganese could be floated with soap, a wetting agent, and fuel oil to give a recovery of better than 75 pct with a grade of 43 pct Mn. The concentrate when nodulized with coke would upgrade to 46 pct Mn or over, and the lead volatilized to 0.6 pct residual.

Jan 1, 1955

By Svend Rordam

THE development of a cement that will resist the destructive action of sea water and other corrosive waters is a problem that has occupied cement chemists for the past one hundred years. It has been found that of the various salts that commonly occur in corrosive waters, sodium sulphate, magnesium sulphate and magnesium chloride are most destruc-tive to cement. Many investigations have been carried out in the United States, in Canada, and in Europe to solve the problem of what constitutes a sulphate-resistant cement, and during the past 10 years some of the findings give definite information in this respect. COMPOSITION OF CEMENT Portland cement is composed of four major compounds: 1. Tricalcium silicate 3CaO.Si02 (C3S) 2. Dicalcium silicate 2CaO.Si02 (C2S) 3. Tricalcium aluminate 3CaO.Al203 (C3A) 4. Tetracalcium aluminoferrite 4CaO.Al203.Fe203 (C4AF) The two calcium silicates are the main contributors of strength. The tricalcium aluminate contributes some to the early strength of the cement but has the least resistance of the four compounds toward the attack of sulphate waters. The tetracalcium aluminoferrite does not contribute very much to the strength, but is far more resistant to sulphate waters than the tricalcium aluminate. When hardened cement is exposed to water containing sodium or magnesium sulphates, these salts will react with the hydrated tricalcium aluminate in the cement and form compounds that will cause a swelling, disruption and crumbling of the hardened cement.

Jan 1, 1939

By C. E. Shoenfelt

The deepening of the General Crude Oil Company's No. 1 Meyers, NE. NE. SE. of sec. 22, 24S., 36E., in the Cooper area of Lea County, in April, 1934, resulted in the discovery of an oil field of major importance. The discovery well is an old well drilled by Cranfill $ Reynolds and completed in July, 1929, in limestone at 3438 ft. for an initial production of 90,000,000 cu. ft. (estimated) of 'gas. Deepening operations were started early in April, 1934, and cores were taken from the old total depth of 3438 to 3508 ft. A Haliburton test taken through the drill stem at 3439 to 3460 ft. showed 50,000,000 cu. ft. of gas with an increase of 5,000,000 cu. ft. between 3461 and 3474 ft. When completed the well tested 12,000,000 cu. ft. of gas and 5000 bbl. of oil at 3474-3508 feet. The new oil field—the result of this discovery—is between the Eunice and the Jal fields, closer to the productive area of Jal than to that of Eunice but far enough away from both to be considered a separate area. Eventually, all of these pools may be joined together by productive oil wells to form a single unit of large size. They lie in a general northwest-southeast alignment and the intervening areas have not been condemned by dry holes. In the drilling campaign that followed this discovery, 24 wells were drilled, of which 23 were oil wells with combined initial productions of

Jan 1, 1935

By John W. Straton

The President of the United States signed Public Law 91-173 on December 30, 1969 and the Federal Coal Mine Health and Safety Act of 1969 became law. The Bureau of Mines was required to promulgate regulations to implement the law. Unfortunately, some stipulations of the Act were not technologically possible. The USBM employed many new inspectors and had to instruct both old and new personnel in the requirements of the law. Mine operators and mine workers also had to be informed. There was a fair measure of inconsistency during this period. Progress is being made, however, and it is becoming easier for mining personnel to know what needs to be done. There are some unresolved questions, however, and there still appears to be an appreciable lack of uniformity in the application of the law by the many federal inspectors.

Jan 10, 1972

By W. F. Hosford

A quantitative explanation is offered for the peculiar curled grain shapes found in the microstructures of drawn wires of bcc metals and compressed aluminum specimens. It is shown that once an [011] fiber texture is developed, the slip system are so oriented that further slip tends to produce plane strain rather than axially symmetric flow of individual grains. With plane -strain flow, however, compatibility of neighboring grains can be maintained only by a bending of grains about one another. PROBABLY the most obvious microstructural feature of heavily worked metals is the distorted shapes of grains. In the course of deformation, the shape change of each grain must be compatible with that of neighboring grains; otherwise holes would be formed at grain boundaries. In analyses of poly-crystalline deformation by Taylor and subsequent workers it was assumed that grain boundary compatability was maintained by each grain undergoing the same shape change as the polycrystalline aggregate in which it is imbedded. According to this assumption, when simple tension or compression is applied to a random polycrystal or to one with a fiber texture, each grain ought to deform with axially symmetric flow. Initially equiaxed grains should become cigar-shaped during wire drawing and pancake-shaped during compression. While microstructural observations of deformed metals are generally in accord with such a picture, certain striking exceptions may be noted. Peck and Thomas5'8 found that grains in heavily drawn tungsten, iron, and niobium (columbium) wires become shaped like ribbons curled about the wire axis, Fig. 1. At a suggestion from the author, they rationalized the development of these micro-structures by considering the orientation of the slip systems in the [011] texture formed by the wire drawing. It is shown in this paper that marked departure from axially symmetric flow of grains is also observed when polycrystalline aluminum is severely compressed. Again the explanation must lie in the orientation of the slip system in the [011] texture, which is formed in fcc metals by compression.' THEORY A simple quantitative argument will be presented to show that the development of these microstructures is a result of flow on the combination of slip systems for which the minimum amount of mechanical work is expended in producing a unit tensile (or compressive) strain. First it must be realized that the macroscopic strains of a crystal resulting from slip are given by: where d dy, and dc, are normal strain increments parallel to the x, y, and z reference axes; are crystallographic shear-strain increments on slip systems

Jan 1, 1964

By J. M. Lohr

A COMMERCIAL development requiring a suitable alloy or alloys for sealing into various grades of glass made it desirable to have a more exact knowledge of the expansion characteristics of the nickel-iron alloys than appeared in the published literature. The expansion of the more common. FIG. I.-EXPANSION CURVES OF SEVERAL FIG. 2.-EXPANSION CURVES OF TWO TYPES OF GLASS. (Courtesy of R. C. A.) TYPES OF GLASS. (Courtesy of R. C. A.) types of glass under consideration varies from 2.7 to 10.4 X 10-6 per degree Centigrade, over the range 20° to 400° C. For reference, the thermal expansion curves f several types of glass used for sealing by the lamp and tube industries are given (Figs. 1 and 2). This paper covers a detailed investigation of the thermal expansion of a series of nickel-iron alloys in which the nickel content varies from 30 to 70 per cent. Particular stress is laid on the alloys that contain between 40 and 55 per cent Ni.

Jan 1, 1938