Search Documents

By Brahm Prakash, R. Schuhmann

Chemical conditions for flotation and nonflotation of cassiterite and fluorite with oleic acid as collector and with alizarin dyes as modifying agents were studied by means of small-scale, vacuum-flotation tests. Artificial cassiterite was prepared fot these tests by high-temperature methods, especially by crystallization from borax melts. FLOTATION test work on Bolivian tin ores some years ago led to the development of several workable schemes of selective soap flotation, but left unanswered many questions of soap-flotation chemistry.' Accordingly, the study of the activation and soap flotation of quartz just reported? was undertaken as a start toward the elucidation of some of the unanswered questions. The experimental work on quartz flotation consisted primarily of small-scale, vacuum-flotation tests in which activator and collector additions and pH were varied between wide limits. In the work to be described in this paper, the soap flotation of cassiterite and fluorite was studied by the vacuum-flotation technique developed in the previous study of quartz. Using oleic acid as collector, conditions for floating cassiterite and fluorite in the absence of modifying agents were first determined. Then the effects of barium, calcium, and alizarin dyes on the flotation of cassiterite, fluorite, and quartz were studied. Alizarin dyes were chosen for study because of the promise they have shown as selective modifying agents in the flotation of non-sulphide minerals.12,1 Also, they form a family of reagents in which there should be a systematic correlation of chemical properties with composition. As a preliminary to the study of cassiterite flotation, an investigation of the preparation of synthetic cassiterite and X ray studies of natural and synthetic cassiterite were undertaken. Experimental Methods The flotation technique and most of the reagent preparations were described fully in the previous paper.' In addition, for the present work it was necessary to prepare satisfactory stocks of clean cassiterite and fluorite and to obtain samples of alizarin dyes. Cassiterite: High-grade cassiterite from the Netherlands East Indies was crushed, sized, and cleaned

Jan 1, 1951

By J. F. Breedis

The stabilization of austenite in Fe-Ni alloys against martensitic transformation after reversion has been attributed' to the lattice imperfections remaining from previous transformation. More recently, however, such stabilization has been associatedzy3 with compositional changes which occur in martensite during slow heating. Dislocation arrangements in deformed austenitic stainless steels strongly influence transformation to martensite on quenching.4 Therefore, it is of interest to observe the transformation behavior of stainless steel after reversion, especially since previous studies have been confined to Fe-Ni alloys. The transformation-product morphology also differs in the two iron-alloy systems;6 plate martensite forms in the latter while stainless steel transforms to lath-type martensite. Samples of Fe-16 wt pct Cr-12 wt pct Ni (maximum C + N = 0.005 wt pct, 0 = 0.02 wt pct), prepared by vacuum melting and casting from high-purity components, were annealed at 900°C for 24 hr, after cold rolling to produce a 40-p grain diameter. The M, temperature of this alloy is -80°C and samples are fully austenitic after annealing. The amount of martensite present after quenching, annealing, and requenching was determined magnetically, to within 0.01 wt pct, using a vibrating specimen magnetometer. Nearly 14 pct of martensite forms during the initial quench in 1 min at -196°C. Two-min and 2-hr anneals were done in air and in evacuated quartz capsules, respectively. All specimens were electro-polished before making the magnetic measurements.

Jan 1, 1967

By Stanley D. Michaelson, Ben. H. Slothower

The depletion of most high-grade ore reserves coupled with growing demands for metals and fuels has made it necessary to bring into production increasingly lower grade deposits. Improvements in technology have made lower grade ores economically recoverable in spite of major increases in labor and material costs and the initial investments required to open new mines and build their metallurgical and service plants. To remain competitive, managements of mining companies must keep abreast of and exploit these often complex technical developments. The proper application of these improvements in technology requires extensive and detailed study. In addition, managements of mining and other industries are becoming more deeply involved in public affairs and the myriad of other nontechnical problems common to all industries. These involvements, plus the demands of evaluating technological developments as well as the necessary work related to the routine administration of operations, have required mining managements to delegate additional study and review functions to staff services. To help overcome the problems involved in adopting the best technologies, managements have generally expanded their engineering and research staff services. Integrated, base-metal-producing companies, having open pits, concentrators, smelters, and refineries, are generally more research and engineering oriented than are most smaller mining companies and quarries. However, mining methods for even the simplest open pits and quarries are improving rapidly, and installations of these improvements are essential to combat increasing costs. Because of this, the managements of smaller operations may also require enhanced engineering staff services to realize the potential benefits.

Jan 1, 1968

By Harold M. Mooney

WHEN apparent resistivity data are taken with the symmetrical Wenner 4-electrode spread, a fixed center position is used and readings are taken for values of electrode separation. Basic data consist of apparent resistivity plotted against separation of adjacent electrodes . The interpreter attempts to infer geologic structure, such as the depth to discontinuities and the nature of subsurface earth materials. An earlier paper' described methods for interpreting resistivity data. All of these involve a severe assumption, namely that the earth in the region of interest consists of horizontal layers, electrically homogeneous and isotropic. The actual earth never satisfies this assumption exactly and may deviate from it so much that none of the above methods can be applied. Attempts in three directions have been made to modify the assumption so that it approaches known geologic complexity more closely. First, curves have been calculated for dipping discontinuities. Stern' and Aldredge hose a few widely separated dip angles. Trudu confined his attention to small dips. Berel'kovskiy and Zubanov computed gradient curves for widely separated dip angles. Unz as given the most complete solution, with a brief attempt to treat the three-layer case. Second, anisotropy can be taken into account. It seems geologically probable that layered materials have different vertical and horizontal conductivities. Cagniard, Maillet, and Pirson et up methods for finding an equivalent hypothetical isotropic medium. Standard interpretation methods can be applied to this, and the actual medium can then be deduced. Belluigi'" discounts the practical importance of anisotropy; Geneslay and Rouget do not agree with his conclusion. Third, the effect of variable resistivity in a layer can be considered. Keck and Colby" examine the mathematics of an exponential increase in a surface layer. Several authors, for example, Stevenson,'' consider a continuous variation of resistivity with depth. The present paper deals with a linear variation of resistivity in a surface layer. Geologically, surface variations should be expected. Unconsolidated materials such as glacial drift show marked irregularities over short distances. The effects of weathering change with depth. The moisture content of material above the water table may vary from a dry sand to a saturated clay, and both of these will be changed by rainfall. Figs. 1 to 6 present apparent resistivity curves to show the effect of a variable surface layer. In all cases resistivity varies linearly with depth down to a depth of one unit. Material beneath this depth has constant resistivity. Electrode separation is plotted in depth units. Insets on each figure show the corresponding cross-sections, plotting true resistivity against depth. To illustrate, consider curve A of Fig. 1. The true resistivity of material at the surface of the earth is taken as 0.4 units. Resistivity increases with depth, reaching a value of 1.0 at 0.5 depth units and 1.6 at 1.0 depth units. Below a depth of 1.0, all the material has very low resistivity (zero, for purposes of calculation). Curve A in the main part of Fig. 1 shows how apparent resistivity varies for this case as the electrode spacing is increased. To illustrate further, curve E of Fig. 4 corresponds to true resistivity of 1.2 units at the surface, 1.0 at a depth of 0.5 units, 0.8 at a depth of 1.0, and 1.5 for all depths greater than 1.0. Apparent resistivity curves have been plotted logarithmically so that the shape of the curves becomes independent of the units, giving the curves wide validity. A certain drift-covered area, for example, shows a gradual decrease of resistivity from 230 ohm-meters at the surface to 150 ohm-meters at the bedrock surface, 275 ft down; bedrock resistivity is 800 ohm-meters. Curve E of Fig. 5 indicates that true resistivity decreases from 1.2 units at the surface to 0.8 at a depth of 1.0, then increases abruptly to a constant value of 4.0 units. Since resistivity and depth ratios are the same, this can be used to predict the field curve. For Fig. 5, multiply true resistivity and apparent resistivity by

Jan 1, 1955

By Richard D. Dick

The Los Alamos National Laboratory was involved in an oil shale fragmentation research program in cooperation with a Consortium of industrial companies to investigate the feasibility of using modified in-situ (MIS) recovery of oil from oil shale. Field tests were conducted at the Anvil Points Mine, Colorado, in the thick oil shale beds of the Green River formation. Part of the program included obtaining data about fragmentation by instrumenting the tests with accelerometers, velocity gauges, and the CORRTEX technique (Continuous Reflectometry for Radius versus Time Experiments). Some of the rock motion data from accelerometer and velocity gauges is presented, along with some conclusions. In addition, the signal recording system is briefly explained. The CORRTEX technique is discussed, and some results on explosive performance and stem behavior using the method are discussed.

Jan 1, 1984

By E. L. Kamen, H. D. Kessler, M. Hansen, D. J. McPherson

The highly reactive Ti-Mo and Ti-Cb alloys were prepared and heat treated under protective conditions. Phase diagrams were established based on micrographic and X-ray diffraction analysis and detection of incipient melting. ß titanium forms a continuous series of solid solutions with both molybdenum and columbium, whereas these metals are only slightly soluble in the a titanium modification. PREVIOUS work on the Ti-Mo and Ti-Cb systems was very limited and is discussed in succeeding sections of this paper relating to the respective phase diagrams. The diagrams in the present work were determined principally by micrographic analysis, because other methods such as thermal analysis and dilatometry are not suitable, due to the low diffusion rates of these alloys in the transformation range. X-ray analysis was believed less useful than micrographic analysis because: 1—On quenching certain high titanium alloys from above their transformation range, the body-centered cubic ß phase decomposes into acicular a (hexagonal close-packed) which room temperature X-ray diffraction techniques cannot differentiate from isothermal a. 2— High temperature X-ray techniques might be used, but are difficult to apply and are subject to error because of the high reactivity of titanium with gases such as oxygen and nitrogen. Although metallo-graphic study was the basic method used, X-ray diffraction analysis was applied to a limited extent, to further substantiate the findings. The transformation ranges on the titanium side of the Ti-Cb and Ti-Mo systems were studied both with DuPont Process A (magnesium-reduced) titanium alloys and with iodide titanium alloys. The Process A metal was used chiefly to bracket the transformation range in order to reduce the number of alloys given a particular treatment for the more accurate final study with iodide titanium alloys. Experimental Procedure The analyses of the metals used in the preparation of alloys for this study are presented in Table I. Melting Practice: Early in the work, a consumable electrode, arc melting furnace was used in the preparation of the Process A Ti-base Mo and Cb alloys. This type of furnace has been described by other investigators.', ' One of the major difficulties of the consumable electrode melting process was the prep- aration of homogeneous electrodes (with the mixture of coarse titanium sponge and fine powder alloying addition) which would give homogeneous ingots. Composition gradients encountered may have been due to a tendency for powdered alloying metals to drop away from the electrode in handling. This difficulty in the preparation of homogeneous alloys was overcome by the use of a nonconsumable electrode furnace for later work. This furnace is similar to the one used by Mc-Pherson and Fontana a Ohio State University. A diagram of the nonconsumable electrode arc furnace is given elsewhere.' The source of power was a 400 amp dc welding generator. Electrode tips of tungsten (% in. in diam) were used for all columbium melts and for a limited number of molybdenum melts. Molybdenum tips were used for the majority of molybdenum alloy melts. Columbium tipped electrodes were tried, but disintegrated rapidly at currents above 300 amp. In the Process A titanium melting practice the metals were charged into the water-cooled spun copper crucible in the following forms: l—titanium: sponge (—4 + 16 mesh); 2—molybdenum: sections of 0.003 in. sheet (approximately ½ in. sq); and 3— columbium: powder compacts (? in. lumps broken from large section). After alternately evacuating and purging the furnace several times with argon or helium, the arc was struck against the metal charge,

Jan 1, 1952

EXECUTIVE COMMITTEES OF LOCAL SECTIONS New York L. W. FRANCIS, Chairman, WILLARD S. MORSE,. Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York, N. Y. P. A. MOSMAN, Treasurer. LOUIS D. HUNTOON. Boston HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. TIMOTHY W. SPRAGUE, HENRY A. WENTWORTH. Columbia F. A. THOMSON, Chairman. GEORGE W. RODDEWIG, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. R. S. McCAFFERY, S. H. RICHARDSON.

Jan 8, 1914

By Thomas C. Wilder

Jan 1, 1965

By K. D. Jacob, W. L. Hill

Fluorine recovery in the United States has been restricted chiefly to manufacture of ordinary superphosphate and wet-process phosphoric acid. However, there is an expanding use of fluorine by industry in the form of hydrofluoric acid. Improved methods for recovering fluorine from phosphate rock would yield an adequate supply of fluosilicates and a substantial contribution to the hydrofluoric acid requirement. THE bulk of natural phosphates is comprised of calcium phosphates, which are usually apatites;' calcium aluminum phosphates such as pseudowavel-1ite; and aluminum phosphates, which occur in extensive deposits, notably on Grand Connetable Island." Nearly all deposits of current commercial value are apatite, often with admixed material of other classes. In the trade coarsely crystalline material, mainly fluorapatite of igneous origin, moves as apatite, whereas the fine-grained material of sedimentary origin is marketed as phosphate rock. The latter classification includes the phosphate shales in western North America. Although several genetic varieties of phosphate rock are recognized, most known reserves are of marine origin. Calcium phosphate is concentrated from Florida land pebble and Florida hard rock deposits and from Tennessee brown rock deposits. Phosphate Rock as a Fluorine Carrier: More than two decades ago Reynolds and Jacob surveyed the fluorine content of commercial phosphate rock from various parts of the world. Later these samples were re-analyzed by a new and more reliable method of determining flourine. The revised results with interim additions of new samples, published a few years ago in a brief summary," are shown in Figs. 1-3. Through the points representing the respective varieties of rock medial straight lines are drawn. In some instances the lines are well defined by the points; in others, where scattering renders the position of the best line uncertain, the greater weight is given points near the end of the covered range. Wherever distinct varieties are not recognized among regional deposits the custom is to identify the sample with the geographical location of the deposit. Although all rock varieties cannot be classified with certainty, the plotted results exhibit three distinct types of rock in which the F to P2O5 ratio diminishes, remains sensibly constant, and increases, respectively, as the grade of rock increases. Existence of two types of Florida land pebble, Fig. 1, is supported by additional results recently supplied by a producer." Generally speaking, phosphate rock from continental deposits carries considerably more fluorine, and apatite and insular phosphates less, in proportion to the phosphorus content than is required by the formula for fluorapatite. Exceptions to this are apatite from Canada and certain samples of Florida waste-pond phosphate. The manner in which excess fluorine is held and the nature of the carbonate in carbonate apatite are discussed in recent articles. High-grade calcium phosphates with F to P2O5 ratios less than 0.05 have been found in Curacao, Christmas Island," Mexic,13 and elsewhere. The calcium aluminum phosphates and aluminum phosphates aften carry notable amounts of fluorine. The F to P2O, ratio for one sample of pseudowavel-lite concentrate was 0.05." Aluminum phosphate from Grand Connetable Island is very low in fluorine, whereas some aluminum phosphate minerals" carry as much fluorine as highly fluorinated phosphate rock. Fluorine in Domestic Phosphate: The curves shown in the figures permit interpolation of the F to P2O5 ratio corresponding to the midpoint of selected ranges in grade of any one of the several varieties of phosphate. Multiplication of the interpolated ratio by the mid-range grade (P2O5) yields a figure for the percentage of fluorine in this grade. Then, with the use of the mid-range grade, the amount of fluorine held in phosphate reserves can be estimated, see Table I. Accordingly, on Jan. 1, 1950, the fluorine complement of known domestic reserves exceeded 420,000,000 long tons of the element. A previous figure," deduced in 1940 by a simpler procedure

Jan 1, 1955

By Joseph Kuti

Longwall mining is the term used for the underground extraction of a wide and deep panel of coal. Such a panel may be blocked out by one or more entries on either side ("head" and "tail") of a longwall face. If all the entries are pre-driven, the panel extraction is termed longwall retreat mining. With one exception, all the longwall faces in the United States are of this type3 Prior to the general decline in the rates of production with Continuous Miners, the development of the multiple entries generally kept ahead of the longwall extraction rate. This is no longer the case: longwall extraction rates far exceed the rate of development. In addition to this problem, in newly established mines, the development of a haulage and bleeder system based on multiple entries results in a lead-time of three years or more before longwall mining can be applied. This is one reason why earlier projections and much of the optimism attached to longwall mining as a principal "savior" in the energy crisis should be viewed with some caution. The alternatives to retreat mining with multiple entries are: Modified retreat mining- where the tail-entry is being formed during the mining of-the panel ("2"-system). Some form of advance mining-where the head-entry or both head and tail entries are being formed as part of the longwall extraction process. These methods are well-known and well-established. Variants of them are being practiced in Canada, Central and South America, but not in the US. It is primarily the laws governing ventilation-conceived for room and pillar mining which prevent the rapid development of these techniques. Another aspect of longwall mining is that it requires a systematic and consistent approach in organization, roof control, ventilation and transport. It is for this reason that compliance with health and safety regulation is fairly well ensured if the longwall system has been well laid out and is subsequently well-run. Nevertheless, a management mentality raised in the great flexibility of the room and pillar system cannot always come to terms with the degree of forward planning and rigid discipline required to successful longwall mining. Research, development and other investments in the partial aspects of longwall mining are always of interest, but no massive trend to longwall can be expected realistically unless these major stumbling blocks in the basic law and basic approach are effectively removed.

Jan 1, 1980

By Clarence R. King

Diamond drilling of Cove Creek deposits and development of flotation-refining process may lead to commercial operation of property worked sporadically for almost a hundred years.

Jan 4, 1953

By A. C. Lane

Relations de la profondeur de plissement avec la gravita-tion et la hauteur des montagnes dans les Alpes. Par A. Heim (Zurich) 50me Anniversaire, Livre Jubilaire Soc. Geol. De Belgique, Rome, Fascicule 1, 17 to 28. Measurements show a negative anomaly, less densities of .the material below sea level. The author expresses it in terms of the thickness of rocks of an arbitrary density, 2.4, which might be considered wanting. The accordant heights of the summits, the depths of the folds, the deficiency in .gravity, and denudation he finds to be connected. The Alps float on the lightness of the folds of "sal" of weight 2.6 to 2.75 plunged into the heavier "Sima" according to a for-mula: P = h (2.7/2.8-2.7) where - P is the depth of fold-ing below sea level; 2.7 is the weight of the material accu-mulated in folding; 2.8 is the weight of the material dis-placed by it; and h is the mean height of the mountainous regions. For instance, between the valley of Saar and the Val de Bagne in Valais the depth of the folds according to Ar-gand's profiles is between 30 and 40 kilometers. The loss of gravity has been estimated in this region as 1450 X 2.4 = 3480 in units of weight. Obviously errors in the densities would profoundly affect the estimates of the thickness of folding, but his depths of folds are obtained from sections, and from them he works back to the densities. Of course other densities might be placed in the formula. Zur Dichte bestimmung von Tonen. By J. Koenigsberger, Berg u. Hüttenmannisches Jahrbuch, 75, I. Discusses Dr. B. Wilser's investigations as to the best way of obtaining the weight of rocks per unit volume. The use of mercury for rocks affected by water as there recom-mended may easily give too large volumes unless 1 to 3 atm. pressure is used. Thick machine oil is recommended for large lumps of clay.

Jan 4, 1928

By J. M. Seeman, R. A. Dodd

If some solution-quenched supersaturated aluminum solid solutions, e.g.., Al(Cu), are plastically deformed at room temperature and then aged at 200oC, the hardness may first decrease before increasing in the usual manner ' A similar transient softening is observed, even in the absence of plastic deformation, when a thin foil or small-diameter wire Al(Cu) specimen is rapidly quenched from the solution-treatment temperature and then aged.' Also, some solution-quenched and neutron-irradiated alloys undergo an initial hardness decrease during subsequent aging.3 The usual explanation of the transient softening in the above examples involves the effect of vacancies introduced by plastic deformation, rapid quenching, and neutron irradiation, respectively However, the mechanism of softening is not unequivo-cably established. In the first-noted case, Gane and parkins' observed that the softening was approximately proportional to the difference in the atomic diameters of solute and solvent, and it was argued that, if a large relative difference in atomic diameter promoted vacancy-assisted room-temperature solute diffusion to dislocations, dislocation climb occurring during subsequent aging at 200°C could cause transient softening. Some substantiation of this theory was offered by the additional observation that discontinuous yielding of solution-quenched polycrystalline Al(Cu) tensile specimens was suppressed by interrupting the test for a short aging treatment at 200°C. Of course, reversion (resolution of GPI) at 200°C would also cause softening, and Sil-cock4 expressed the opinion that the softening in the case of Al(Cu) must be partly associated with reversion. Also, Hirsch5 commented on the possibility that, if jogs cause hardening, an anneal at 200°C should straighten the jogged dislocations and result in softening. However, parkins' has re-expressed his belief that these mechanisms are not entirely consistent with the observed serrated stress-strain curves. Experimental. New data has now been obtained for Al(Cu), Al(Ge), Al(Mg), and Al(Zn) primary solid-solution alloys. These alloys were prepared from metals exceeding 99.99 pct purity, and specimens 4 by 4 in. diam were solution-treated, quenched, deformed 10 pct in compression at room temperature, and aged at 200'C in a cottonseed oil bath for various times. Generally, these operations could not be carried out in rapid succession, so the alloys were stored in a freezer between treatments to minimize aging. The variation in hardness with aging time, Figs. 1 to 4, was determined by microhardness testing with a 3.0-kg load. At least five readings were averaged to obtain each data point, and all measurements were taken about the center circumference of each cylinder (region of maximum deformation). Each specimen was used to obtain only one data point, i.e., specimens were not replaced in the aging bath after measurements were made. In

Jan 1, 1968

By W. H. Morris

I have been requested to present a paper on the slag from the basic Bessemer process, as prepared for fertilizing. Since Professor W. B. Phillips presented at the Birmingham meeting, in May, 1888, an able paper* on this subject, as it had been developed up to that time, there is little for me to add. Perhaps later practice may be best expressed by the homely proverb, " The proof of the pudding is in the eating." As the Pottstown Iron Company is the only concern manufacturing basic Bessemer slag in this country, the writer's personal experience in the use of it may be interesting. Our slag averages: P2O5, 21.37; SiO2,, 5.10; MgO, 5.90; Al2O3, 4.01; MnO, 5.56 ; FeO, 12.00; Na2O and K2O, 0.80; CaO, 45.26; total, 100.00. This gives over 76 per cent. of phosphoric acid and lime. In using this material for several years past on my lawn and garden, I have found it better than anything else I have ever tried ; and I am sure that any of you who had seen my green grass last month (January), wherever the ground was bare from snow, as bright as in early fall, would be forced to acknowledge the advantages of this soil-enricher. The grass on my private lawn, and around the company's office, is green the whole winter; and we have raised very good sod, by the use of this phosphate, where, without it, we were unable to get the grass to grow either from seed or by repeatedly sodding. The same statement applies to garden-truck; when the soil was first broken up, a good crop of vegetables was easily raised. My own gardener has had several premiums from Philadelphia seedsmen (notably, last year, the first premium for sugarcorn raised in the first part of July, being the first sample sent them). Our method of applying this material is to grind the slag very finely, so that at least 60 per cent. of it will go through a 150-mesh screen (i.e., say, 22,500 meshes to the square inch), and 90 per cent. through a 100-mesh screen (i.e., 10,000 meshes to the square inch). This fine grinding seems to be the main condition of success.

Jan 1, 1893

By Stanley Herold

A FEW notes on the occurrence and significance of mud volcanoes in Colombia may be of interest at the present time, owing to the renewed activity in geological exploration of, the coastal regions bordering the Caribbean Sea. The best-known volcanoes are found a few miles from the seacoast. One is situated to the south of Puerto Colombia; the second, to the east: of Cartagena near the village of Turbaco; and the third, near the village of Puerto Escondido south of the Sinu River. Others. are reported in more inaccessible localities. Usually they stand 2 1/2 or 3 ft. (0.762 or 0.914 m.) above the surrounding ground at the crater, though several craters from 10 to 20 ft. (3.04 to 6.09 m.,) apart will often build up an extensive mound at low gradient. The shallow mound may cover 1/2 or 3/4 acre (0.2 to 0.3 ha.) with an elevation of 12 or 15 ft. (3.65 or 4.57 m.) at the center. The craters are formed of hardened blue clay; the inside diameters vary from 14 to 24 in. (35.56 to 60.96 cm.). The rim is continuous, except on one side where there is usually a cut 3 or 4 in. deep, thus allowing an overflow. The craters are filled to the rim-cut- with a thick mixture of blue clay mud and water, which is kept in agitation by escaping gas. Fig. 1 shows the bubble in the act of bursting and Fig. 2 the appearance of the surface of the viscous fluid a second or so later. The frequency of the explosions is determined by the weight of the column of fluid in the neck of the volcano, consequently, such explosions are not synchronous in a group of craters. Ordinarily, there are two or three explosions in about 3' minutes. The supply of gas is small but steady and sufficient pressure must accumulate before the bubble can enter the column of fluid. The water is derived from the surface and enters the sedimentary strata not` far distant from the volcano. During long dry seasons, as the supply of water fails the volcano dries and geyser action ceases.

Jan 7, 1919

By Jan M. Mutmansky, Gordon H. Walrod, Y. J. Wang

The selection of a shaft size for ventilation purposes is a classic problem of concern to mining engineers. This presentation is concerned with the sizing of conventionally-sunk circular shafts with concrete or shotcrete linings. Costs of sinking shafts of three different depths, from 150 m to 300 m (500 ft to l000ft), and six different diameters, from 4.27 m to 7.32 m (14 ft to 24 ft), were obtained through questionnaires to shaft contractors. The primary objective of the economic model presented is the balancing of detailed annual capital and operating costs to achieve the minimum overall cost of the shaft installation over its life. The economic model is similar to previous analyses but treats several of the individual cost categories in an updated fashion. Included in the paper is a detailed analysis of the effects of varying power costs on optimal shaft size. Also included are a statistical analysis of current shaft costs and comments on the choice between shotcrete and concrete linings.

Jan 1, 1980

By J. F. Myers, F. M. Lewis

IN the mining and handling of sulphide ores, some degree of oxidation takes place on the sulphide surfaces, which are exposed to the atmosphere. It is, moreover, well known that the oxidation compounds formed are a factor when such ores are subsequently treated by flotation. Modern operating technique and reagents are capable of contending with this condition to a major degree, provided that the proportions of the reagents used are varied correctly. This is particularly true at the Tennessee Copper Co., where the ore treated contains pyrrhotite in addition to other sulphides. A number of soluble salts, some of which are unstable, can be formed during the oxidation of the sulphide ores. Those unstable salts, whose oxygen requirements are unsatisfied, are constantly changing to more stable forms because oxygen reacts with them during the crushing, grinding and other operations of ore preparation. We add no chemicals of any kind to the ore pulp in its preparation for flotation feed. Consequently the only compounds that are present in the flotation feed are those produced by the natural oxidation of the ore in the presence of air and water. The Tennessee Copper Co. ore is composed of from 60 to 70 per cent sulphides and from 40 to 30 per cent nonsulphide material. It is not the purpose of this paper to discuss the nature of these various oxygensulphur compounds nor their effect on flotation, but to describe a method for [ ] correcting the effect. Suffice it to say that we have found that the reducing sulphur and oxygen salts have a depressing action on our bulk flotation process.1 From long experience we find that the best means of correcting for this variation in our work is to increase or decrease the quantity of xanthate, the promoting agent, as the quantity of the reducing salts increases or decreases. It was, therefore, very desirable to provide the operators with some quick and

Jan 1, 1946

Jan 1, 1938

By H. J. Hager

The Alabama By-Products Corp. is an entirely independent Alabama enterprise. Organization of the company stemmed from the consolidation of three important properties in the Birmingham District and a by-product coke plant at Tarrant, Ala. In 1924 ABC was merged with the Pratt Consolidated Coal Co. This merger greatly extended the company's holdings of valuable coal lands in Walker and Jefferson Counties.

Jan 12, 1950

By M. G. F. Söhnlein

In a Bolivian tin concentrator an appliance was needed to furnish a suitable product for fine jigging from a pulp of the following composition: Mesh Per Cent. + 20 8.0 40 36.5 + 60 9.0 + 80 10.5 + loo 5.5 4-150 1 4.5 -150 25.0 99.0 Loss 1.0 In the jigging process, particles of cassiterite as small as 0.1 mm. can be recovered, provided they are not present in excess, that is if the material treated on the jigs contains sufficient coarser sands to keep the interstices between the grains open. Removing the fine material from the pulp by screening, to prepare the jig feed, is impractical, because that means the use of an 80-mesh screen or finer, and is not as effective as hydraulic classification. A screen would eliminate mineral grains from the feed which can be recovered by jigging, and in addition would throw more gangue and low-grade middling on to the jig. Formerly a one-spigot Richards vortex classifier had been used to accomplish this separation, but the tangential openings through which the hydraulic water enters became clogged by fine vegetal matter with which the water was contaminated, and which it was impossible to remove from the water. Consequently the work of the classifier was imperfect and a good deal of slime was sent to the jig. When designing the plant referred to in this paper it was decided to use a hydraulic classifier as shown in Fig. 1. The essential features had been copied from the Anaconda classifier.' This remodeled classifier consists of a truncated pyramidal wooden hopper A with an attachment of cast iron

Jan 1, 1917