Search Documents

By F. Claisse, R. Angers

Self-diffusion in iron has been measured during rapid a-r transformations using a variant of the Kryukou and Zhukhovitskii diffusion method. The study was performed by thermally cycling iron foils (1 to 6 cpm) through the transformation (=910°C). Some foils have been subjected to over 1000 cycles and some have spent more than 15 pct of their total diffusion time in the process of transformation. The experimental results show that the a-r transformation has no measurable effect on self-diffusion in iron. The study is completed by a quantitative analysis of mechanisms which can affect the diffusion rate during the transformation. The analysis confirms the experimental results. SINCE diffusion is an important factor in many solid-state transformations, it is of interest to study how it is affected by the stresses generated during these transformations. Clinard and Sherby1'2 were the first to make a study along these lines. They measured diffusion coefficients in Fe-FeCoV couples subjected to slow thermal cycling (1.5 cph) through the a-r transformation range. They found an enhancement of diffusion by a factor of about two. The purpose of the present paper is to report measurements of the self-diffusion coefficient of iron during much more rapid thermal cyclings (1 to 6 cpm) through the a-r transformation (-910°C). These more rapid cyclings produce higher strain rates during the transformation and should emphasize any possible influence of transformation upon diffusion. EXPERIMENTAL Iron foils, 25 to 35 µ thick, were cold-rolled from 99.92 pct pure iron and annealed in pure helium for 2 hr at 870°C; the resulting grain diameter was about 150 µ. Specimens 0.5 by 8 cm were cut from the foils and I7e55 was vapor deposited on one of their surfaces. A 38 gage alumel-chrome1 thermocouple was spot welded in the middle of one of the specimen long edges, Fig. 1. Two 38 gage chrome1 wires were also spot welded along the same edge on each side of the thermocouple; they were placed 2.5 cm apart and used for electrical resistance measurements. In order to prevent twisting and crumpling, the specimens were pinched between two quartz plates 0.1 by 1 by 7 cm and the assembly was close fitted into a 1 cm ID quartz tube. Four holes were drilled through the tube to let the 38 gage wires out: these were connected to the recording equipment by means of extension wires. 20-gage nickel wires fixed at both ends of the specimens were used to thermally cycle the foils by Joule heating. The above described device was placed in a 2.7 cm ID quartz tube which in turn was placed in a tubular furnace. Either a pure helium atmosphere or circulating hydrogen was used during the experiments. Specimens were subjected to thermal cycles between a minimum temperature To and a maximum temperature Tm at rates ranging from 1 to 6 cpm. This was obtained by maintaining the furnace at a constant temperature near the minimum temperature To and periodically passing an electric current through the specimen. Cooling was achieved by heat losses to the surroundings. The forms and periods of cycles were varied from one specimen to another; however, each specimen was subjected to one type of cycle only. The temperature and electrical resistance variations of the specimens were recorded as a function of time. The temperature curves were used for diffusion calculations while the electrical resistance curves were used to monitor the transformation and to determine its starting point and its approximate duration. Diffusion was measured by the method developed by Kryukov and zhukhovitskii3 and modified by Angers and Claisse.4,5 In this method a metallic foil is coated on one side with a radioactive isotope and the activity is measured periodically on both sides during the diffusion anneal. The following equation then holds: where: I1 Activity on the surface on which the deposit is made. I, Activity on the opposite surface. t Diffusion time. B Constant. D Diffusion coefficient. d Foil thickness including the deposit. G(t) A function of time; it is a second order correction term which is given graphically in Refs. 4 and 5. The diffusion coefficient D is found by plotting ln[(Il - I2)/(I1 + I,)] -G(t) against t; the resulting slope m leads to an accurate calculation of D through Eq. [2]. The effect of the a-r transformation on diffusion is expressed by the ratio DT/DU where:

Jan 1, 1970

By Alan K. Burton

Along with tires and transmission systems, engines have been a limiting factor in the growth of large off- highway trucks. The problem, primarily, has been the development of reliable, high-performance engines that are not prohibitively heavy or expensive. For many years, horsepower to overall truck weight ratios have been in the vicinity of 300 lb per hp for rear dump units up to 50 tons capacity. This ratio is obviously very poor when compared to the much lighter and smaller highway trucks, which frequently have a performance ratio of 100 lb per hp. Unfortunately, the larger mining trucks have not been able to match even the 50-ton trucks, and in some cases, ratios have dropped as low as 450 lb per hp. This results in a performance of only 67% of that achieved by the older smaller trucks. Thus, the message is clear: what is needed is more horsepower and less weight.

Jan 10, 1975

By L. O. Howard

Much work has been done recently on the lead-antimony system1 in connection with lead-rich alloys of commercial importance containing less than 20 per cent. antimony. Dean, Zickrick and Nix have called attention to the perpetuation in the literature of several erroneous data, such as a eutectic temperature of 228° C. at 12.5 per cent. antimony, instead of 247° at 13 per cent. The series is given as a classic example of a straight eutectiferous series in such late books as those of Heyn and Grossmann, 2 Jeffries and Archer,3 Guillet and Portevin,4 Pulsifer,5 Rosenhain,6 and Liddell,' as well as the somewhat earlier works of Hof-man (1918), Wang (1909), and Williams (1920). The work of Dean has definitely shown a solid solution of antimony in lead at about 2.5 per cent. antimony. While lecturing to a class in general metallurgy at the University of Idaho, the writer had the students prepare a series of lead-antimony alloys for the purpose of illustrating methods of thermal analysis. Proper proportions of powdered antimony (sold as C.P.) and test lead were mixed and melted in graphite crucibles under a reducing cover. Cooling

THE committee in charge of arrangements for the meeting of the Institute in September has com-pleted its program. The headquarters of the meeting will be at the Palace Hotel, San Francisco, and the registration committee will be at the hotel all day on Sunday, Sept. 24, and from 8 a.m. until noon on Monday. On Sunday afternoon, automobiles will be available for sightseeing trips around the city. Monday will be devoted to technical sessions. In the morning, there will be sessions on Mining and on Iron and Steel; in the afternoon, sessions on Mining and Milling. At these sessions, in addition to the papers mentioned in the tentative list printed in August, there will be presented three papers on the geology, mining and milling of the Comstock lode; one on the Aztec mine, Baldy, N. M.; one on the Colombian oil fields; and one on charcoal precipitation of cyanide solutions. The luncheon on that day will be Dutch Treat, for men only, at the Engineers Club. On Monday evening, there will be an informal buffet supper at the home of F. W. Bradley. On Tuesday morning, a party of 50 men will leave for Hetch Hetchy. During the four days of the trip, the party will see the Priest tunnel and earth dam under construction by steam-shovel and hydraulic-fill methods, the Big Creek shaft and tunnel, early intake power plant and tunnels and the Hetch Hetchy dam under construction. For those who remain in San Francisco, Tuesday will be "San Francisco Day." There will be motor trips to the Presidio, Cliff House, Golden Gate Park, and other points of interest, and shopping trips to Chinatown. On Wednesday, "University of California Day," the party will be guided through the university by members of the Mining Association, the affiliated stu-dent society, and will see the Greak Theatre and not-able buildings. Thursday will be "Leland Standford, Jr. University Day." Automobiles will leave the Palace Hotel at 10 a.m., and will return from the university at 4.30 p.m. Friday has been reserved for trips to the Selby Smelter, to Mt. Tamalpais, or to other points of interest. Arrangements will be made to visit the mines or gold dredges in California, if members desire to do so, but such trips must of necessity be considered special trips and arrangements will have to be made to suit the convenience of the individual or party. The Golf Committee will make arrangements for those who wish to play golf.

Jan 9, 1922

By D. J. Coolidge, H. L. Sheakley

THIS paper does not deal with all sands used in the glass industry in Missouri; it covers only that used in the plate-glass factory at Crystal City. However, it is probably safe to say that other sands, pro- [ ] duced throughout the state for this purpose, are of identical nature. The glass sand used in Missouri is commonly called the St. Peter deposit, which is ascribed to the Ordovician Rock series in the form of sandstone. This St. Peter deposit, aside from a few small outliers, covers a large area of eastern Missouri. It forms, through a broad curve, the northeast margin of the typical Ozark region between Cape Girardeau on the southeast and Mineola, Montgomery County, on the northwest. The belt is extremely irregular, varying from one to ten miles in width; its length is 150 miles in a straight line. [ ] The outcrop near the entrance to the Crystal City mine appears in the form of a sandstone bluff approximately 30 ft. high, running along Plattin Creek (Fig. , I). Above the sand rock an overburden of Joachim limestone appears, which, thickens to nearly 300 ft. and forms the hill commonly called Buck Knob. Test holes, where drilled at various points and the drillers' log indicate that the St. Peter deposit ranges in thickness from 63 to 71 feet. PROPERTIES OT THE ST. PETER SAND From an analysis of the glass sands of the St. Peter formation in Missouri, the follow-

Jan 1, 1942

By S. E. Maddigan, B. R. Zimmerman

MOST metallurgists are well acquainted with the contributions already made to the study of metals by the use of X-rays. On the one hand, the radiographic method is constantly becoming of increasing importance as a nondestructive testing procedure, while on the other hand the techniques of X-ray diffraction have made important contributions to the fundamental knowledge in studies of phase diagrams, stress conditions, and so forth. A new, and as yet insufficiently appreciated, tool exists in the application of microradiography to alloy structures. This new procedure in many respects bears the same relation to microscopic investigations as does macroradiography to the gross inspection of metal surfaces. However, where macroradiography is used ordinarily to determine the soundness of the metal structure, this new method can be used not only to investigate micro-un- soundness but also to examine the distribution of the constituent elements within the body of the alloy. When combined with the normal procedures of microscopy, this offers a technique of great potential power. It is intended in this paper to present a few examples of copper-base alloys demonstrating the additional knowledge obtained from the microradiographic method. The detection of micro-unsoundness is demonstrated in Fig. I for a sample of cartridge brass as cast. The sample appeared quite sound when viewed under the microscope, but in reality was thickly populated with minute voids. This application of the method conforms in every way to conventional large-scale radiography and has been used to facilitate production of metal for vacuum devices.1 The true potentialities of the technique are revealed by comparison of Figs. 2a and 2b, which are respectively a- photomicrograph and a microradiograph of a cast alloy of 80 per cent Cu, 10 per cent Sn, 10 per cent Pb. The remarkable difference in appearance provides some concept of the additional information this method may yield when used as an auxiliary to microscopic studies. Fig. 2a shows two phases of the copper-tin system plus segregated lumps of lead. Fig. ab, on the other hand, shows with exceptional clarity the actual dendritic growth of the metal crystals during solidification. The practice of microradiography depends upon the laws of absorption of X-rays. This subject has been reviewed thoroughly in recent papers,1,2,3 but for clarity a brief resumé will be given here. As is well known, when a beam of X-rays is transmitted through a layer of homogeneous material, the intensity is reduced according to the relation:[ ]

Jan 1, 1944

By G. K. Manning, W. E. Few

T has been known for some time that both'inter-granular carbide and intergranular oxide phases cause brittleness in molybdenum. Parke and Ham' indicated that 0.0025 pct 0 present in molybdenum after solidification from the melt was sufficient to induce intergranular brittleness during forging. However, material containing 0.06 pct C could still be forged. However, adding this amount of carbon to insure deoxidation causes the formation of carbides on freezing. These carbides are precipitated at grain boundaries, and Rengstorff and Fischer' have shown they have an unfavorable effect on the room-temperature ductility of molybdenum. Take? in 1928 proposed that the solubility of carbon was a constant value of 0.30 pct from room temperature up to 1800°C. In 1935, Sykes, Van Horn, and Tucker' obtained X-ray data suggesting that the solid solubility of carbon in molybdenum was between 0.07 and 0.09 pct at temperatures from 1500" to 2100°C. The a-solubility line for carbon was included in the Mo-C diagram given in the Metals Handbook as a tentative line based on the data of Sykes, Van Horn, and Tucker. In order to determine the partial phase diagrams for these systems, it was necessary to construct a high-temperature furnace suitable for heat treating molybdenum at temperatures up to 4000°F. A molybdenum resistance furnace was built for this purpose in which samples could be heat treated in a purified atmosphere and quenched from any desired temperature.' Experimental Work Solubility of Carbon: Arc-cast molybdenum supplied by the Climax Molybdenum Co. and 18-gage molybdenum wire samples produced by powder metallurgy at the Fansteel Metallurgical Co. were used in determining the a-solubility line for the MO-C system. The cast molybdenum contained 0.032 pct C initially. Two lots of 18-gage wire were used, one containing 0.011 pct C and the other 0.005 pct C initially. All material contained a carbide phase as received. Fig. 1 illustrates the carbides found in the untreated material. Heat treatment in a purified hydrogen atmosphere was found to reduce the carbon content in the as-cast molybdenum. Purified argonT also decarburized molybdenum samples at temperatures above 3500°F; however, the carbon content remained constant during heat treatment in purified argon at lower tem- peratures. The argon was purified by passing it over titanium at 750 °C and then through a magnesium perchlorate drying tower. The hydrogen was purified by passing it through a commercial hydrogen deoxidizer, followed by a drying tower. Specimens having different initial carbon contents were heat treated in argon at 3500°F for periods ranging from 5 min to 5 hr and were analyzed for carbon. Samples of the same final carbon content had the same microstructures regardless of time at temperature. Furthermore, a gradient between center and surface in the amount of undissolved carbide particles present was never observed. It was concluded that at these low carbon levels, and at the high temperatures involved, diffusion proceeds so rapidly that the specimen is always substantially homogeneous in carbon content, in spite of the gradual loss in carbon. Based on the above findings, the following procedure was used to determine the carbon-solubility limit at 3000°, 3500°, and 4000°F. At each of these temperatures, a number of samples were heat treated, as shown in Table I, and rapidly cooled to room temperature. Since the samples lost carbon in proportion to the length of time heated, a series of samples were obtained of varying carbon contents. By use of a rapid cooling rate, the phases present at the high temperature were retained at room temperature. All samples were examined microscopically. Those found to contain either no excess carbide phase or only a very small amount were then analyzed for carbon. The samples actually analyzed for carbon

Jan 1, 1953

Iowa State College Ames, Iowa Iowa State Mining Society CARL S. NELSON, President NORMAN S. GEIST, Secretary K. A. PHILLIPS, Faculty Sponsor C. G. DRESSER, Counselor University Of Kansas Lawrence, Kansas University of Kansas Student Chapter of A.I.M.E. WALTER CROOK, President EDWARD C. MISHOU, Secretary E. A. STEPHENSON, Faculty Sponsor GEORGE M. FOWLER, Counselor K. A. SPENCER, Counselor .

Jan 1, 1942

By P. H. Brace, N. A. Ziegler

The study of the relations between gases and metals is one of pcren-nial interest to all who are connected with the production of high-grade metallurgical products. The data reported here are the outcome of work of which the object is to determine the effects of dissolved gases upon the properties of metals and to gain a more detailed knowledge of the reactions between gases and molten metals, particularly iron, under definitely controlled conditions. We have attempted to reduce our margin of error by dealing with relatively large quantities of metal, from 4 to 13 Ih. (2 to 6 kg.), and keeping the ratio of refractories to metal as small as practicable. The ingots produced are large enough to provide adequate material for making determinations of magnetic and other physical properties. In choosing the bell-jar type of furnace we were influenced by the results of considerable experimentation along the same general line which indicated that, for the scale on which we were to work, it was important to have the furnace structure independent of the vacuum enclosure. The use of a bell-jar surrounding the entire furnace accomplishes this and also gives great freedom of observation during operation and ready accessibility for the replacements which are necessary after each run. Our choice of analytical method was made in the light of the results secured by H. M. Ryder, who used a method similar in principle for the analysis of very small quantities of gas extracted from strips of metal heated electrically in high vacuum. We have presented some selected preliminary experirnental data as being illustrative of the quantity and nature of the gases which occur in iron of different origins, but do not urgc any hypothesis at this time. The Furnace Our furnace may be described as "a high-frequency induction furnacc of the bell-jar type." It is similar in a general way to that described by Cain and Peterson1 though we have introduced certain refinements of

By W. O. Borcherdt

THE 650-ton underground mill of The Empire Zinc Company of Colorado (a subsidiary of The New Jersey Zinc Co.) serves the Eagle mine at Gilman in the Battle Mountain mining district of Colorado, The topography is rough, the mine and mill being under Battle Mountain and the adit entrance in the north wall of the canyon of the Eagle River, which is here a steep gorge. The town of Gilman stands on a shoulder of the mountain at altitude 8975 ft., above sea level, along the Pike's Peak ocean to ocean highway and contains the company office and the usual facilities of a modern mining town. The railway contact is at Belden, altitude 8370 ft., at the bottom of the gorge directly below Gilman, where the westbound track of the Denver and Rio Grande Western Railroad is cut along the north bank and the eastbound track along the south bank of the river. A general description of the mine, mill and service facilities, with an account of the geology, character of the ore and methods of mining and milling having previously been published in a series of articles1, this paper will discuss with as little repetition as practicable the reasons for building the mill underground rather than as a conventional structure, the methods of construction employed and the experiences gained in what is apparently the pioneer plant of this type and extent. There is a large historical background for underground plant construction. From the dim past caves have been used for dwellings, stables, storage and shops. It was natural that where caves were available their many advantages led to their enlargement to suit convenience and where they were not available but the ground conditions, topography and drainage were favorable, to the construction of artificial caves. In the vicinity of Epernay, France, extensive underground chambers protect the manufacture and storage of champagne-an intricate and ingenious application of chemical engineering-and in recent years these plants have been mechanized by the installation of conveyor systems. In the

Jan 1, 1937

T. A. Rickard, Denver, Colorado: The observations made by the author concerning the treatment of gold-bearing ores, deal with the subject only briefly and in a general way; but, coming from an authority, they invite comment. In stating the fact that a " finely-divided condition " is a necessary characteristic of ores containing free gold, the author must be refer ring to those mining districts only with which he himself is ac quainted. The statement would not be true of certain gold-mining regions in America and Australia. The ores of some Californian mines and the mill-stuff treated at certain of the mills of Clunes and Ballarat in Australia, and of Otago in New Zealand, contain the gold in a free but in a coarse state. Moreover, "reduction to fine sand and flour" is not required by certain ores, even though the gold be in a finely-divided condition. In such cases the gold becomes de tached from the quartz before the gangue has been pulverized into particles as small as those in which the gold occurs. The dry-crushing of free-milling gold-ores is onknown in the new mining regions of the world. It is not clear whether the author has in mind any European district in which such a process is in actual use. If he has, a description of the method and the results obtained would be very valuable. Dry-crushing is, other things being equal, twice as slow and twice as expensive as wet-crushing. In the case of free-milling gold-quartz it serves no purpose, since such ore does not carry sulphides which contain any large percentage of value, and which, by being slimed, may carry away part of that value. The dry-crushing of a free-milling gold-quartz would be considered an absurdity by an American metallurgist. If the ore contain "free gold only," why submit it to a further treatment, such as concentration, after its passage over the amalga mating-plate ? What does the author propose to concentrate ? Again, why anticipate the treatment of tailings by the McArthur Forrest, or some other process ? The satisfaction felt by a mill-man in saving gold by a subsequent treatment of the tailings from his mill appears to me to be like that of the man who shoots at a rabbit,

Jan 1, 1894

By Berlen Moneymaker

THE development, within recent years, of core drills capable of drilling holes up to 72 in., or even more, in diameter, has made possible an entirely new and valuable method of geologic exploration, Although little used until recently as an exploratory tool except in the United States, by the Tennessee Valley Authority and the Corps of Engineers of the U. S. Army, for the exploration of damsites, the large-diameter core drill may be used to good advantage in other types of geologic exploration. Its princi-pal utility is that of supplementing, rather than replacing, other means of exploration. Although core is frequently recovered intact, the greatest advantage of large-diameter drilling is that the holes produced are large enough to be entered by the geologist and engineer, and thus afford an excellent means of examining undisturbed rock. The walls of the holes are smoothly cut, and in some rocks nearly or quite polished, so that the most minute details of structure and stratigraphy are clearly disclosed. Such features as faults, joints, bedding planes, weathered "seams," and beds or layers of soft materials, which are not always amenable to disclosure by cores recovered from small-diameter holes, are conspicuously displayed in the walls of large holes. Frequent reference to the drilling of large-diameter holes is made in engineering literature, but comparatively little emphasis has been placed on their value in geologic investigation. It is, therefore, intended that the present paper acquaint the geologist, as well as the engineer, with the large-diameter core drill and the technique involved in its use, and also with its advantages, disadvantages and limitations as an implement of geologic exploration.

Jan 1, 1938

By W. W. Little

At the United Verde mine the 9-2D stope on the 4050 ft level is located within the north sulphide mass lying some 800 ft north of the main sulphide ore body. In 1948 it was estimated that this block contained 85,000 tons of ore at 4% copper and 9.2% zinc. The north ore body is a lenticular replacement deposit in the black schist, extending from about 100 ft above the 3750 level to a distance below the 4500 level yet to be determined. Although the mineralized zone approaches 1000 ft in length, only 300 ft is of economic importance. In width it varies from a maximum of 60 ft to about 3 ft at the north end, and is characterized by pinching and swelling in the ore zone. One of these larger swells is being mined as the 9-2D stope. Mining costs at greater depth, together with the expected grade of ore after dilution, necessitated a low cost mining method to permit profitable stoping operations. Based on the results obtained in a number of Canadian mines, it was decided to develop the ore body for stoping by the Aldermac or bench method of diamond drill blastholes; however, this plan was subsequently changed and the radial or ring method adopted. Such a method seemed to offer the advantage of large tonnages at low cost, and obviate the necessity of waste fill. This latter point was of particular importance, since the present waste system does not extend below the 3000 level.

Jan 4, 1950

Connecticut Geological and Natural History Survey, P O Box 1106, New Haven, Conn W. E Britton, Superintendent. A complete list of Bulletins available will be sent upon request. Address all inquiries for publications to: George S Godard, State Librarian, Hartford, Conn Fifty-one Bulletins have been issued, 15 of which are of particular interest, dealing with the geology of the state, and are available as follows; 4, The clays and clay industries of Connecticut, by G. F Loughlin (1905), 35 cents; 8, Bibliography of Connecticut geology, by H E Gregory (1907), 20 cents, 13, The lithology of Connecticut, by J Barrell and G. F Loughlin (1910), 45 cents, 18, Triassic fishes of Connecticut, by C. R Eastman (1911), 30 cents, 23, Central Connecticut in the geologic past, by J. Barrell (1915), 20 cents, 24, Triassic life of the Connecticut Valley, by R Lull (1915), 70 cents, 29, The Quaternary geology of the New Haven region, Connecticut, by F. Ward (1920), 60 cents, 30, Drainage modifications, and glaciation in the Danbury region, Connecticut, by Ruth S. Harvey (1920), 55 cents, 33, Geology of the Stonington region, Connecticut, by L H. Martin (1925), 60 cents, 40, The geology of the Shepaug Aqueduct Tunnel, Litchfield County, Connecticut, by W M. Agar (1927), 50 cents; 41, Guide to the geology of Middletown, Connecticut, and Vicinity, by W. N Rice and W. G Foye (1927), $1, 44, Report on the water resources of Connecticut, by R. H Suttee (1928), $1, 46, The physical history of the Connecticut shoreline, by H S Sharp (1929), 75 cents; 47, The glacial geology of Connecticut, by R F. Flint (1929), $2, 51, Minerals of Connecticut, by J F Schairer (1932), 75 cents Bulletin 51 explains the physical and chemical properties of minerals, their classification, and describes more than 100 common minerals found in Connecticut. A bibliography is included The Survey gratuitously distributes all its Bulletins to state residents, scientific institutions, etc. Prices quoted are to private citizens of other states

Jan 1, 1933

By G. W. P. Rengstorff, L. E. Olds

PREVIOUS research has shown that cast molyb-denum has good ductility at room temperature if the metal is sufficiently pure. In practice, however, it is very difficult to reduce the impurity content of molybdenum to a few parts per million—the maximum content of impurities allowable to obtain reasonable ductility in coarse-grained molybdenum. Also, subsequent fabrication may reintroduce enough impurity to damage ductility greatly, unless extreme precautions are taken to protect the metal during working. The major impurities which embrittle molybdenum are oxygen, nitrogen and, to a lesser degree, carbon. It is reasonable to assume that the harmful effects of such impurities might be neutralized by small amounts of alloying additions. The desired alloying elements would be those which might fonn stable metal oxides or nitrides that would not be harmful to ductility, or thosewhich might increase the tolerance of molybdenum for oxygen and nitro-

Jan 1, 1958

By B. F. Tillson

HAVING been asked to talk about recent devel-opments in mining equipment, I chose the sub-ject of small units of storage-battery locomo-tives which recently have been developed with the idea of motorizing transportation in the mines as far as possible, replacing the manual labor of hand-tramming. Metal mines are probably less advanced in this field than coal mines, where transportation of large ton-nages on any one level is quite common. Of course, metal mines, where large tonnages are handled on any one level, are as advanced as coal mines, and storage-battery locomotives for main haulages are used quite commonly in such metal mines, but the mines having levels at many intervals in the depth of the orebody, or a number of intermediate levels in which a consider-able amount of hand-tramming has to be done, and small metal mines in which the size of the orebody does not seem to warrant the initial capital expenditure for the driving of main haulage levels and installation of rock and ore chutes and raises for the delivery of the broken ore and rock to the cars have been at consider-able disadvantage in replacing manual labor by some mechanical means of transportation. Several years ago the field was canvassed among the manufacturers of electric-locomotive equipment and the conclusion was reached that the art had not been devel-oped to the advantage of metal miners who desire to replace small units of labor by locomotive equipment. The need for such small locomotives is all the more em-phasized by the development in the past few years of mechanical mucking-machines (loading equipment for filling the cars from muck piles on the level). Any me-chanical loader is a liability instead of an asset unless means are also provided for keeping the material away from the loading-machines. Therefore the transporta-tion system must be equal to the capacity of a loading-machine, otherwise the latter is idle such a large per-centage of its time as to prove an unprofitable invest-ment. So there is a need for portable, small haulage units to handle small mine cars in many metal mines, and, naturally, units are desired which can be so readily shifted from level to level as to facilitate their free use. Of course, in mines in which each level comes to the shaft it is not such a difficult problem, but many mines have a great many intermediate levels which must be approached through raises, timber slides or other small openings required to transfer ore and to get timber and other supplies to those levels.

Jan 5, 1927

By J. W. Rutter, K. T. Aust

The motion of individual grain boundaries under a constant driving force was investi,qated for zone-refined lead, with and without solute tin additions. The rate of boundary migration was found to depend strongly on tin content and on the orientation relationship between the adjacent grains. The results are compared with the theory of impurity-controlled grain boundary miqration developed by Lucke and Detert. Evidence was found that grain boundaries separating grains which have the Kronberg-U&apos;ilson orientation relationships of 38 and 22 deg about <Ill> and 28 deg about <100>, correspond to boundaries of high mobility. The results are discussed in relation to the formation of annealing textures in metals and the structure of high-angle boundaries. It is generally known that small amounts of impurities in solid solution greatly influence the re-crystallization behavior of metals. For example, the addition of 0.005 at. pct of tellurium to copper,&apos; or 0.005 at. pct of silver to lead,2or 0.01 at. pct of manganese or nickel to aluminum3 greatly decreases the rate of recrystallization of these metals. However, this effect may be the combined result of a decrease in the rates of both nucleation and growth; recrystallization experiments do not separate these two factors. Bolling and winegard4 determined the effects of small quantities of tin, silver, and gold on grain growth in polycrystalline zone-refined lead.

Jan 1, 1960

By A. L. Barnes

A number of reservoirs have been partially invaded by bottom water. Water flooding such reservoirs can be especially inefficient if the oil has a high viscosity because injected water will under-run the oil and emerge at producing wells without having displaced much oil. A possible means of improving water sweep efficiency would be to precede the water flood with a slug of water purposely thickened with a chemical additive. This possibility has been studied with a scaled laboratory flow model. The investigation was carried out on a model representing a 20-acre five-spot with one set of reservoir condition~. Displacements were performed with water, with viscous-water slugs of 10 and 25 per cent of the pore volume followed by water, and with all viscous water. Displacement tests were made at several rates of injection. For all cases, compared at the same producing water-oil ratio, an increase in rate resulted in an increase in volumetric sweep. The larger the quantity of viscous slug injected, the greater the crossflow of oil ahead of the displacing front and, thus, the lower the WOR during that period of a displacement. This investigation indicates that the injection of aqueous viscous slugs in this type of system would give some additional benefit over conventional flooding by (I) reducing the life of the flood, (2) reducing lifting costs and (3) increasing ultimate recovery. The benefits of a viscous-slug displacement would warrant its use if the viscous water could be created for a few cents per barrel. INTRODUCTION The most appropriate method for water flooding oil reservoirs which have been partially invaded by bottom water has been a problem of considerable interest. Such reservoirs, having good vertical permeability and unfavorable mobility ratios, are difficult to produce efficiently under normal waterflood procedures. Even though the injection wells have been plugged back above the oil-water contact and the water zone has been squeezed off, injection water will enter the formation and not only displace oil, but also much of it will displace the bottom water, thus creating a high producing water-oil ratio at the start of a flood (see Fig. 1). Since the rate of injection and the viscosity of the displacing fluid are the more easily controlled physical parameters of the reservoir, it is quite natural to study their effects on the volumetric sweep of the oil zone and on the producing water-oil ratio. Increasing the viscosity of the displacing fluid has two disadvantages—it reduces the maximum rate of injection into the reservoir, and it costs more than water. It was thought that the injection of a viscous-fluid slug, followed by water, would minimize these two disadvantages, increase the volumetric sweep of the oil zone and reduce the producing water-oil ratio. Water with an additive to increase viscosity would probably be the most effective. The primary purpose of this investigation was to determine the feasibility of injecting viscous-water slugs followed by water to improve or hasten oil recovery while reducing the producing water-oil ratios. The effect of injection rate upon recovery was also investigated. A laboratory model, scaled to a 20-acre five-spot prototype with one set of reservoir conditions, was constructed. Laboratory studies of displacements with (1) water, (2) viscous-water slugs of 10 and 25 per cent of the pore volume followed by water and (3) all viscous water were performed at several rates of injection. THEORY OF SAND MODEL SCALING There are two conventional means of determining scaling criteria. These are dimensional analysis and inspec-tional analysis. Determining scaling criteria by dimensional

By G. T. Jackson

PROPERTY AND LOCATION THE Alaska Gastineau Mining Co.&apos;s mine is located at Perseverance, about 4 mi. east of Juneau, Alaska. Its property consists of a group of claims, the lode system traversing these claims for a distance of 11,000 ft. (3352 in.). It is shown in Fig. 1. FIG. 1.-ALASKA GASTINEAU MINING CO.&apos;S PROPERTY NEAR JUNEAU. The ore deposits occur in what is known as the Juneau gold belt. This gold belt can be traced for about 50 mi. northwest of Juneau and 40 mi. southeast. It consists of a single band, several hundred feet wide, in which stringers and veins of quartz, carrying gold, occur in a slate formation near its contact with some altered volcanic rock known as greenstone.

Jan 9, 1919

By R. Kossowsky

USING etch-pit techniques, Johnston and Gilman&apos; have shown that the stress dependence of dislocation velocity can be represented by the expression where r, is the dislocation velocity, a is the applied stress, and oa, is the stress to produce a unit velocity. Noble and Hul12 showed that the exponent m is strain-dependent and increases rapidly in the work-hardening region. This was explained by arguing that in the work-hardened material the applied stress required for any given velocity will be greater than in the annealed material by an amount equal to a back stress due to work hardening. schadler3 has stressed the importance of substructure as a possible source of error in dislocation velocity measurements, and took care to make velocity measurements in which dislocations moved such short distances that interactions with boundaries were avoided. schadler3 also pointed out that, if standard testing equipment is used, measurements of m from flow stress data could be seriously in error in materials with a high initial work-hardening rate. Noble and Hu112 have further argued that, due to the strain dependence of m , the extrapolation to zero strain4 to obtain the true value of m can be justified only in the preyield region. Microstrain experiments in high-purity iron5,6 have led to the conclusion that aiA (Ref. 5) (defined as the stress to first produce a permanent set of 10-6 in. per in.) and oflow are not controlled by the same deformation mechanism. It has been proposed5,6 that aA is governed by the lattice resistance to the motion of screw dislocations in a given slip plane and that oflow is controlled by the lattice resistance to a full-scale cross slip. The purpose of this note is to extend Noble and Hull&apos;s argument further and to show that measurements of m from flow stress data can be in error due to the rapid increase in stress in the microstrain region6 when stress is increased beyond aA. Double z-one-refined single crystals of molybdenum (with the (101)[ 111] slip system operating and a Schmidt factor of 0.475) were used in an experimen-

Jan 1, 1968