Search Documents

By J. B. Mackintosh

The general method which has been followed since the time of Heinrich Rose, and perhaps before, for the determination of phosphorus in iron and steel, is to dissolve the sample either in nitric acid, aqua regia, or some other oxidizing agent, in order to convert the phosphorus into phosphoric acid. In 1832 Rose* recommends HNO3, or aqua regia, preferably the former. Wohler, in 1854,† directs that the iron should be oxidized by burning in a stream of oxygen for the determination of carbon, and the resulting oxide of iron containing all the phosphorus as phosphoric acid be treated as an ore. In the fourth English edition of Fresenius' Quantitative Analysis,† pp. 666-667, we find directions to dissolve the iron in aqua regia or bromine; and, coming down to more recent times, we find F. A. Cairns § directing the employment of a boiling solution of potassium chlorate and hydrochloric acid for the oxidation and solution of the sample to be analyzed. It is unnecessary to multiply quotations from the literature of the subject, though they might be extended almost inclefinitely, since it would only be a repetition of the above mentioned series of methods in one form or another; and the references given have been selected to show how little essential variation there is in the type-methods of solution used. In fact it seems to be universally accepted as a necessary first step in the determination that some such method of solution should be followed. One chemist, however, struck out on a different line of thought, and to the Lest of my knowledge only one, M. V. Tantin, who, in

Jan 1, 1886

By I. S. Servi, N. W. Marr

TIN markedly increases the softening temperature of pure copper with only a moderate effect on conductivity. Smart and smith' indicated a substantial increase in softening temperature upon addition of different levels of tin up to 0.05 pct in oxygen-free copper. However, after finding no effect of tin in copper containing about 0.025 pct O, they concluded that "the presence of oxygen completely nullifies these changes in properties by precipitation of SnO2.'' Since preliminary tests on Cu-Sn-0 alloys indicated that this conclusion is not valid outside the extremely limited tin range investigated by Smart and Smith, research was primarily directed toward the partition of tin between the copper-base matrix and the oxide phases. Experimental. Material was prepared by sealing an 80 to 100-g charge consisting of oxygen-free copper, tin, and copper oxide into a y-in.-ID quartz capsule which was evacuated and back-filled with tank-grade argon to 3 atm. The sealed vials were heated to 1125ºC, kept at temperature for 30 min, occasionally agitated, and then allowed to air-cool outside the furnace ("as-cast"). The castings were cold-swaged to 0.370 in., annealed 1 hr at 600°C ("as-annealed"), and cold-swaged 16.5 pct ("as-swaged"). Cross sectional wafers were annealed for 1 hr at various temperatures and Rockwell F hardness measured. The "softening temperature" was defined as the interpolated temperature at which the hardness was 50 Rockwell F. Electrical resistance was measured by an ac poten-tiometric method on 0.040-in.-diam wires after a 1 hr anneal at 600°C. Relative accuracy was of the order of 1 pct. Chemical analyses for tin were performed by two methods, identified as "Acid flux" and "HN03 dissolution". The first consisted of fusing the sample with potassium pyrosulfate and leaching the resulting melt with 10 pct sulfuric acid. The spectrophotometric procedure which followed is described in Ref. 2. Oxygen analyses were performed by the vacuum-fusion method with a bath temperature of 1650°C. Tin content of oxides and copper phases was measured with the X-ray microprobe, using a calibration curve based on a series of oxygen-free Cu-Sn alloys. Results. In Fig. 1, the nominal tin composition for alloys containing nominally 400 ppm O was plotted vs the analyzed or the computed tin content—the latter derived from one of the following: 1) "acid flux" chemical analysis; 2) "HN03 dissolution" chemical analysis; 3) X-ray microprobe analysis of the copper matrix; 4) equivalent tin content, based on the measured increase in electrical resistivity (an increase in resistivity of 1.6 microhm-cm is approximately equivalent to 1 wt pct of sn1,3). It is evident from Fig. 1 that the results of the acid flux analysis are consistent with the nominal composition while the HNO3 dissolution method generally yields lower values, consistent with those obtained from electrical resistivity measurements and somewhat higher than those obtained by microprobe analysis. Microprobe and resistivity values are affected only by the tin in solid solution; hence the HN03 method

Jan 1, 1970

By V. Runolinna, R. T. Hukki

Preliminary separation of precious metals by flotation can offer a simplification of the conventional method of treatment of anode slimes. Laboratory flotation experiments show that rich gold and silver concentrate can be obtained with excellent recoveries. THE purpose of this paper is to present the results of an investigation into the possibilities of separating precious metals from anode slimes by selective flotation. The work was carried out at the State Research Institute in Helsinki, Finland. The sample of anode slimes tested was submitted by the Outo-kumpu Co. in Finland. In 1947 the average assay of filtered and dried anode slimes in the Outokumpu refinery in Pori was as follows: Au, 0.50 pct; Ag, 9.38 pct; Cu, 11.02 pct; Ni, 45.21 pct; Pb, 2.62 pct; Fe, 0.60 pct; Sn, 1.00 pct; Sb, 0.04 pct; As, 0.70 pct; Se, 4.33 pct; S, 2.32 pct; SO,, 2.17 pct; SiO2, 2.25 pct. The daily assay naturally varies considerably from the figures presented above. The present conventional method of treatment of anode slimes consists of the steps shown in the flowsheet in fig. 1. As seen from this simplified flowsheet, the present method of treatment involves many steps by which the components of the anode slimes are removed one after another until the main products, gold and silver, may be separated. Due to the small scale of operations, the above procedure is carried out in small batches requiring considerable amount of manual labor. If, however, the anode slimes could be treated in

Jan 1, 1951

By Bradley Stoughton

FRom 1886 to 1889, approximately, Henry M. Howe was engaged most actively in preparing his Afetallugy of Sieei, which became the foundation for his leadership in the science of physical metallurgy of steel. During the same period, Hadfield was developing the first of the industrially-important alloy steels, and Riley was initiating the commercialization of nickel steel. Both of these alloys are treated briefly in Howe's book; indeed, he missed practically nothing of interest in all the steel literature preceding 1889. There had been many good books on steel before his, but none of the same character. His genius, like that of Aristotle and Francis Bacon, manifested itself in the painstaking collection of data, followed by their coordination and interpretation. Not only manganese and nickel steels were discussed, but several which most of us, with our tendency to overlook the past, are wont to regard as exclusively recent developments, such as: silicon, chrome, copper, tungsten, vanadium, titanium, chrome-tungsten and many other steels. But Howe never devoted much special attention, in his writings, to alloy steels; the science of the relations of iron and carbon offered field enough even for his capacity for constructive thought. And, today we find the science of alloy steels in much the same condition as was the metallurgy of steel before Howe wrote his first great book. Many, many important facts have been presented to the world, especially by Sir Robert Hadfield, James Riley, Henri le Chatelier, Kotaro Honda and his associates, Maunsel White, Harry Brearley, and a host of others. Several books have been devoted wholly or chiefly to alloy steels, such as those by Hibbard, Mars, Heyn and Wetzell, Grube, Burnham, Gillett and Mack, Billón, Brearley, Monypenny, Becker, Savoia, Sauveur, Guillet, Tammann, Guertler, Goerens, Guia, Wuest, Ledebur, Schenck, Aitchison, Osann, Guettier, Buchetti, Escard. The vast number of data on the subject are indicated by a bibliography' which was collected in preparing this address. It covers the years 1911 to

Jan 1, 1927

By A. B. Kinzel, Walter Crafts

Inclusions of nonmetallic matter have long been recognized as objectionable in steel. A complete theory of the effect of inclusions, which is consistent with that held today, was outlined in Howe's early work on the metallurgy of iron and steel. This, by analogy with wrought iron, assumes that the observed difference in properties between specimens with and across the direction of rolling is due to slag enclosures. The fact that wrought iron shatters in ballistic test is taken as an indication of the effect of inclusions on the resistance to'shock. Since that time, the development of the metallurgical microscope has shown the discrete nonmetallic inclusions in the iron matrix. Better resolution has brought out the great number of inclusions, and the availability of good microscopes in steel mills and laboratories has constantly drawn more attention to these inclusions. This recent emphasis on inclusions has resulted in studies as to their nature, mode of formation and methods of elimination, such as the work of Wohrman, Dickenson, Herty and Schenk. In addition to the published works, many investigations which have not been published have been carried out by private laboratories and have resulted in the application of specifications intended to limit inclusions in many qualities of steel. Neverthless, a clear understanding of the quantitative effect of inclusions on the physical properties of steel has been lacking. It is the specific purpose of this study to determine the quantitative effect of inclusions on the physical properties of steel that determine its behavior under dynamic stress. The study has shown that a quantitative relation between counted inclusions and impact strength does exist in normalized steels, but that factors other than readily visible inclusions are equally important. Furthermore, the present commercial rating of inclusions is unreliable with respect to counted inclusions or dynamic tests, and this study indicates that the tensile-impact test is more reliable as a measure of quality. General Scheme The general plan of the study follows: (1) To develop or establish a satisfactory measure of dynamic strength; (2) to develop or establish a

Jan 1, 1931

By Erhard Hornbogen

Twins were propagated into large, well-annealed crystals of a, iron-phosphorous and a, iron-molybdenum solid solutions. Strain fields caused by interaction of these twins were made visible by precipitation. These strain fields can be explained by assuming that transmitted and reflected plastic waves are created when a twin strikes an obstacle with high velocity. The twin front itself can be regarded as a shear wave that may be able to develop a one-dimensional shock front. The occurrence of {WO} fracture by the reflected stress is also discussed. The described effects were not found when twins propagated at lout velocity into disturbed crystals, for example, into crystals previously deformed by slip. DEFORMATION twinning leads to shearing of a crystal lattice under external load. The shear appears to be homogeneous over a large number of crystal layers. In a iron, shear occurs on the (112) planes and in the <1ll> directions. The formation of a twin proceeds by the movement of partial dislocations that change the stacking at the twinning plane.l, In the bcc lattice, this partial dislocation can be created by dissociation of a sessile a/2[111] dislocation that lies in the (112) plane: Cottrell and Bilby&apos;s spiral mechanism can explain the homogeneous shear, but has not been proven experimentally. Nevertheless, this mechanism can explain the possible high velocity of formation of a twin. In Cottrell and Bilby&apos;s model, as in other models of twinning or phase transformation, a much higher energy is required to spread the first stacking fault than to add new layers by further movement of the partial dislocations. The dislocations will therefore become accelerated proportional to the difference between the stress, tN, to nucleate and tp to propagate the twin. It has been assumed3,4 that tn is the stress required to make two partial dislocations of apposite sign pass for the first time. After the first layer of new stacking has been formed, the maximum stress is TN=Gb/4pd where G is the shear modulus, b is the Burgers vector of the partial dislocation, and d is their perpendicular spacing so that the amount of shear is S = b/d. From this formula, a value of 25 kg per mm2 has been estimated for twinning in Zn3. The measured values are smaller, but local internal stresses may help to provide the necessary stress. For a iron, a higher value can be expected, mainly due to the higher value of G. That agrees with the observation that "burst" twinning occurs if the yield strength is in-

Jan 1, 1962

By E. A. Sondreal, F. I. Honea

This paper summarizes coal and ash properties and pilot-plant results for 14 key lignite seams in the Gulf Province, as well as discusses operating problems encountered by the four Texas power plants burning Gulf Province lignite. Some consideration is given to the design of future power plants.

Jan 1, 1982

By Frank E. Hall

The needs of the World War showed the necessity of a metal stronger than cast iron which would supplement the supply of steel. SO patriotic metallurgists were spurred to new efforts to improve the status of that half-breed of the metal world that had been, more or less erroneously, christened semisteel. As a result, it was developed that for certain purposes semisteel was superior to steel in the manufacture of shells. Steel, because of its greater strength and toughness, is able to carry a greater charge of explosive, weight for weight; consequently, a steel shell can be expected to cause greater destruction when used against fortifications or other inanimate objects, while semisteel, because of its comparative brittleness and its resulting greater fragmentation, is capable of inflicting more serious loss of life when used against opposing forces of men. Therefore, each has its proper place in the economy of war. For the present purpose, steel may be defined as a comparatively pure iron whose physical nature is modified by small amounts of carbon, silicon, sulfur, phosphorus, manganese, and possibly other rarer elements; while cast iron generally is limited to approximately 93 per cent. of iron, the remainder consisting of larger percentages of carbon, silicon, sulfur, phosphorus, and manganese. Semisteel may be defined as cast iron in which the carbon and silicon have been reduced to as low a point as is consistent with maintaining the nature of gray iron, and in which the remaining elements are adjusted so as to give the greatest strength. The fact that the addition of steel scrap, in varying percentages, is the means used to reduce the carbon, together with the fact that a considerable increase in strength results, is probably the explanation of the origin of the name semisteel. That ordinary grades of steel show from three to four times the tensile strength of cast iron is due to the fact that the crystals, or grains, of cast iron are interspersed with flakes of

Jan 1, 1922

By Charles F. Park

Mining in the Pacific Coastal Region has passed through three stages of development. First came the gold rush days, a period when gold and silver were the objects of intensive search. Second was the development of the high-grade base-metal deposits and of the smaller and more refractory precious metal deposits. And third was the modern period that covers the discovery and development of the rarer metals, of large low-grade deposits, and of the industrial and nonmetallic minerals. Brief discussions of the salient geologic features of the region and of a few of the better known mineral deposits are given. The regional geology is favorable for continued exploration and discovery of new deposits and districts.

Jan 1, 1968

By Max Roesler

I. INTRODUCTION THE following article concerns the geological occurrence of the iron-ore deposits on the south coast of Cuba. The article is based on a detailed field study, made in the hope that some information would I gained which might be of value in the search for further orebodies, Or in the economic development of the ore already found. LOCATION The iron-ore deposits of the Firmeza district lie near the coast, in the southeastern part of Cuba, in the Province of Oriente. The orebodies of this district form part of a belt of deposits that extends from Sigua, 25 miles east of Santiago, to Sevilla, 5 miles east of Santiago, and lies on the seaward slope of the Sierra Maestra range of mountains.

Jan 10, 1916

By S. R. Seagle, R. Schuhmann, N. A. Parlee

Rates of CO evolution and CO absorption were measured for liquid-iron alloys containing from 0.15 to 4.4 pet C, using a modified Sieverts apparatus. The alloys were held in alumina crucibles, so that both crucible-metal and gas-metal reactions occurred simultaneously. The data are interpreted on the hypothesis that the C-O reaction rate is controlled by oxygen diffusion across the boundary layers at the gas-metal and crucible-metal surfaces. CARBON-monoxide evolution from liquid Fe-C-0 alloys is a key reaction in steelmaking processes, both in the steelmaking furnace and in the ingot mold. Also, this reaction probably is an essential step in the desulfurization of iron under blast-furnace conditions, for which carbon is the principal reducing agent or deoxidizer present in the iron. The thermodynamic properties of the solutions of C and 0 in Fe and the equilibria of these solutions with gaseous CO and CO, have been investigated in some detail and are reasonably well understood. However, while these equilibrium data have accumulated in the laboratory, other data have accumulated to show that equilibrium conditions are often not achieved under plant operating conditions. Thus, an understanding of the rate and mechanism of the carbon-oxygen reaction not only has theoretical interest, but ultimately may assume considerable practical importance. Reaction Mechanisms and Rate Equations The over-all reaction under consideration is C (in liquid Fe) + 0 (in liquid Fe) + CO (gas) [I] Although this appears to be a straightforward heterogeneous reaction, involving just two phases (liquid metal and gas), a wide variety of reaction mechanisms has been proposed. Different authors have expressed divergent views as to the nature of the rate-controlling steps. Accordingly, a brief discussion of the possible reaction steps will be given. 1) Homogeneous Reaction Within Liquid Iron— Feild&apos; and Jette2 have applied chemical reaction-rate theory as if the C-0 reaction were a homogeneous, second-order reaction occurring within the liquid-metal phase. This mechanism necessarily produces CO "molecules" dissolved in liquid iron. In order to yield CO gas, the dissolved CO must nucleate CO gas bubbles, and the dissolved CO also must be transported to the bubble surface where it enters the gas phase. However, this mechanism is inconsistent with present concepts of the structure of liquid-metal solutions. 2) Reaction at Gas-Metal Interface—At the surface of contact between gas and metal, a second-order reaction between dissolved C and 0 may occur to produce a CO molecule which enters the gas phase. This reaction presumably involves an "activated complex" structure in the interface. Some such surface mechanism appears essential because the carbon and oxygen do not occur in the same species in the two phases and therefore must react in some way at the surface. At liquid-iron temperatures, calculations based on reaction-rate theory indicate that the surface reaction must proceed extremely rapidly and thus cannot be a rate-determining step in the C-O reaction under ordinary conditions.3 ccordingly when the over-all reaction is measurably slow, the surface reaction may be considered at equilibrium; that is Cc* Co* = m&apos;Pco [2] in which Co* and Co* are the concentrations of carbon and oxygen (weight per unit volume of metal), respectively, in the liquid-metal phase at the interface, Poo* is partial pressure of CO in the gas phase at the surface (atmospheres), and m&apos; is the mass-action constant for Reaction [I]. Since activities of C and 0 are not strictly proportional to concentrations, m&apos; is not a true thermodynamic equilibrium constant but varies with carbon content.&apos; 3) Mass Transport—If the reaction is to proceed at the gas-metal surface, as described above, dissolved carbon and oxygen in the liquid iron must come to the surface and gaseous carbon monoxide must move away from the surface. Details of the mass-transport mechanisms depend on the kind of system under consideration. For a stirred metal bath in contact with a CO gas phase, the transport of C and 0 to the surface can be described by 1 Do Mols CO evolved per sec = — 1/16— Do/do Agm (CO-Co*) = 1/12 Do/do Agm *(Co-Co*) [3] In this equation, Do and D, are the diffusion constants for oxygen and carbon in liquid iron, 6, and 6,. are the boundary-layer thicknesses, A,,,, is the

Jan 1, 1959

By R. M. Rose, D. P. Ferriss, J. Wulff

Single crystals of tantalum were grown by multipass zone melting in an electron beam apparatus. Tension tests of these crystals at 4.2 x 10&apos;* per sec-gave a resolved louler yield stress of 7300 psi at with a chisel edge; total uniform deformation increased from 1 to 2 pct at 77°K to over 20 pct at 300°K. This, and slip traces, indicated that deformation is more inhomogeneous at lower temperatures. Deformation occurred exclusively by slip in <III> directions, on planes in the <111> zones. Cross slip was frequent, particularly for those orientations where the resolved shear stress on the cross system was comparable with that on the primary plane. The existence and magnitude of the upper yield point were found to be sensitive to orientation. This effect was related to the circumvention of dislocations which were "locked" by interstitial atoms, by double cross slip, or composite slip, of screw dislocations. Prestrainirg at 300°K did not remove the upper yield point in subsequent tension at 77°K. Also, this treatment was found to cause yield points, where none existed for the unprestrained material. This behavior was also rationalized in terms of the circumvention mechanism. The mechanical properties of polycrystalline tantalum have been investigated by several workers,1"4 and may be summarized by pointing out the following features: a) Sharp rise of yield stress with decreasing temperature below room temperature. b) Response to strain aging at 300" to 400"C. c) Yielding with upper and lower yield-point phenomenon at and below room temperature. d) Low strain hardening below room temperature. e) Reluctance to twin except at very high strain rate. Furthermore, tantalum is ductile at ordinary strain rates as low as 4.2"K.&apos; This feature, in particular, makes tantalum unique among the high melting point, bee transition metals of Groups V and VI in the periodic system. Therefore, a more fundamental and detailed knowledge of the low-tempera- ture deformation of tantalum is required. Since high purity and the absence of grain boundary effects make such a study most productive and unambiguous, the method of electron beam zone melting was selected for the preparation of test specimens. This technique has the further advantage that crystals may be seeded in order to obtain any desired orientation. EXPERIMENTAL The electron beam zone-melting equipment was constructed as a modification of that described by Calverley, Davis, and Lever? All crystals were made by three passes of the molten zone at 4 mm per min to achieve an optimum purity commensurate with economy of time and material. Table I reports the chemical analyses of the starting and refined metal. It will be noted that there remain some 50 to 70 wt ppm of interstitial elements, while all substi-tutional elements have been removed by evaporation. Tungsten is picked up by evaporation of the cathode filament wire. Crystal seeding was normally successful within 3 deg, and the orientation of all crystals are given in the standard stereographic triangle in Fig. 1. Tensile bars were prepared from the crystals by centerless grinding to the shape in Fig. 2. Specimens were then electropolished to remove 10 pct of the diameter in order to remove worked material and to prepare a metallographic surface for subsequent deformation trace observations. All specimens were held in the split bushing grips as indicated in the cross section view of Fig. 2. All tests were made at a strain rate of 2 112 pct per min in an Instron testing machine.

Jan 1, 1962

By C. E. Shoenfelt

There was very little oil activity in Utah in 1938. A few wildcat tests were drilled and the well at Cane Creek, started in 1937, was in active operation, but failed to reach its objective by the close of the year. The Clay Basin field in Daggett County, northeastern Utah, was extended about a mile east by the Mountain Fuel Supply Co. with the completion early in June of No. 3-D Murphy, NW. NW. SW. of sec. 23-3N-24 E. This well had an initial production of 16,000,000 Cu. ft. of gas a day under 2160 Ib. pressure, from Dakota sand at 5918 to 5925 ft. after plugging back from a total depth of 6035 feet. The Clay Basin field, in the few years it has been in operation, has developed into a gas field of major importance. Approximately 1300 acres has now been proved by development. Six wells are on production, five of which were completed in Dakota sand and the sixth in a sand in the Frontier formation. The field was connected to the Salt Lake line

Jan 1, 1939

By Thomas N. Walthier

ROSPECTING for uranium in the East is hampered by the lack of bedrock exposure due to extensive overburden and residual soil. But, despite the problems of this physiographic province, it has not been ignored in the search for radioactive materials. Since 1951 both the U.S. Geological Survey and the Atomic Energy Commission have had field parties in the eastern U.S. Tempo of private prospecting is increasing, and many discoveries have resulted. AEC work so far has been concentrated in the areas of most numerous discoveries-Pennsylvania, New Jersey, and New York. Accounts of uranium mineralization in the eastern U.S. are found in the old literature and one site in the Mauch Chunk area of Pennsylvania has been known since 1874. In 1949 McKeown examined the original occurrence there and found another southeast of the town. The deposit appeared to have commercial possibilities and a short period of production began in July 1954

Jun 1, 1955

By L. F. Mashburn, T. J. Ferree

A Reichert cone concentrator was installed in an aggregate plant circuit to recover the extremely fine "flour gold" known to exist in the deposit. The gold content of the bank- run gravels averages about 0.1 g/t-about $1.29/t, based upon $12.86/g ($400 per oz) gold. The fineness of the gold averages between 950 and 960. The Reichert cone, in conjunction with a conventional shaking table, recovers in excess of 85% of the gold. A screen analysis of the gold particles shows 44.1 % is - 74pm (-200 mesh) in size. The plant operates with a two-man crew.

Jan 1, 1983

By K. A. Slagle, D. K. Smith

weight obtained. Additives used in conjunction with salt in these slurries have included silica flour, calcium ligno-sulfonate and cellulose retarders, granular lost-circulation materials, bentonite and selected low-water-loss additives that are not significantly deteriorated by the presence of the chloride ion. In some other areas of South Texas, the salt-saturated slurries have been used quite extensively for improvement of the flow properties of slurries and attainment of better circulation characteristics at lower displacement rates. Concurrently with this property, the protection of shales and shaly sands is also realized, as well as useful retardation of the slurry. Resultant superior cementing jobs have been indicated by both communication tests and acoustic logs for bonding to pipe and formation.&apos; In one section of Louisiana, a major oil company has been using salt-saturated API Class A cement with calcium lignosulfonate retarder for cementing through the Miocene at 9,000 to 10,000 ft. This is another of the situations where interbedding of sands and shales exists, creating difficulty in maintaining formation competency when a fresh-water slurry contacts the clay minerals of the formation. Further work has also been done in the shaly Miocene formation at 13,000 to 15,000 ft where fairly close water or gas contacts are encountered. Indications thus far are that better segregation of these various fluids is obtained by use of the saturated salt slurries because of their improved formation bonding characteristics. In addition to the properties of salt in this situation, attainment of turbulent flow at minimum displacement rates has also been accomplished by use of an additive to help provide exceptional dispersion and viscosity reduction of the slurry. Another oil company was encountering considerable expense in completing wells in Southwestern Louisiana due to extensive block squeeze requirements for effective separation of zones. A very effective mud program was being used to minimize washout in the shale sections and, apparently, a nearly gauge-size hole was being obtained. However, primary cementing results with fresh-water slurries were generally poor. On a few occasions when slurry was actually circulated to the surface, large pieces of shale formation were brought out of the hole with the slurry, indicating a severely water-sensitive, sloughing formation. Inhibition of shale heaving was being accomvlished in the drilling program, and immediately indone ipon circulation of the fresh-water slurry even though it contained a low-fluid-loss additive to reduce filtrate damage in the sands. The subsequent change to salt-saturated slurry yielded 11 successful primary cement jobs out of 12, compared to the previous success ratio of practically zero. Since these were deep, high-temperature wells in the range of 13,000 ft with high-pressure zones necessitating 17.5-lb/gal fluid densities, the slurry used was API Class E cement, silica flour, weight material, retarder, salt saturation (which also reduced the amount of weight material) and maintenance of low fluid loss by use of a salt-compatible additive. Other salt slurries have been used to a limited extent in this same general area for similar problems at depths ranging from 5,000 to 17,000 ft. In the shallower wells, the cement has usually been API Class A where the salt functions as a retarder, and in the deeper wells API Class E cement is used with the additional salt advantage being its increased slurry weight and inability to dissolve salt stringers. A considerable number of squeeze jobs have also been done on older wells using the salt-saturated slurries with very good results. MID-CONTINENT In North Texas, salt-water slurries have been used for cementing the Woodbine sand, Strawn sand, KMA sand and Pettit lime. Shales surrounding these formations have created the same difficulty in obtaining separation of producing zones that has been the problem in other areas. Depths in this area range from 3,400 ft for the Strawn to 7,400 ft for the Woodbine, and concentration of salt has varied accordingly. In the deeper wells, where retardation is desired, saturated salt-water cement is used; for the shallower wells, in order to provide shorter waiting-on-cement times, the amount of salt has been 18 per cent by weight of the mixing water. Results have been excellent with no reported failures on any of the salt cement jobs; where acoustic bond logs have indicated indifferent bonds previously, they are indicating very good bonding for the salt slurries. In Oklahoma various shales of Pennsylvanian age exhibit a high degree of sloughing in the presence of fresh water, causing severe washouts above and below sand formations which it is desired to isolate. This situation exists to some degree in practically all parts of Oklahoma and includes formations of other ages such as the Wood-ford shale. For the past few years, salt-saturated cements and displacement rates as high as practical have been used as a remedy for this problem, with very good results. The Layton and Bartlesville formations are two examples of shaly sands where saturated slurries have been helpful. In one area where five wells were drilled through this type of problem shale without obtaining a satisfactory primary cement job, a change was made to salt-saturated cement preceded by a suitable chemical wash for the drilling mud involved. Acoustic bond logging indicated excellent bonding, and final completion bore out this result by being trouble-free. This type of slurry has also been used extensively on squeeze jobs where shales have been heaving around the producing formations. Predominantly, the basic slurry has been either API Class A cement or a pozzolan cement—although, as deeper wells are being drilled, the use of salt in Class E cement is also increasing. Salt cement in West Texas has been used primarily to help prevent channeling through the shales around the Delaware sand, Queens dolomite and Hope lime. Many of the shaly and dirty sands of this area are sensitive to the filtrate from a fresh-water cement. Salt at 16 to 18 per cent by weight of mixing water has been added to centent, and has been effective in controlling formation damage and communication between zones in these formations. Use of these lower salt concentrations is dictated in this area by the relatively low formation temperatures where retardation of the slurry would create unduly long waiting-on-cement times. Also, quite a bit of cementing has been done in this area using salt concentrations in the accelerating range— that is, 2 to 5 per cent by weight of water. Specifically, these concentrations have been used in coiljunction with high percentages of gel to overcome the retarding effect of the calcium lignosulfonate dispersant, although there are probably several shales where these concentrations could provide some degree of formation stability. On several occasions, the salt has also been used to lower the critical velocity or rate for turbulence with the slurry, particularly in the pozzolan cements. On wells in the Hope lime, it has usually been necessary to squeeze the shale above and below the lime to get a water-free completion. Use of salt-saturated slurries has largely eliminated this

By A. W. Ambrose

THE underground losses of oil exceed by hundreds of thousands of barrels all the oil that has been lost in storage, transportation, or refining. The quantity lost is, of course, indeterminate; but when it is considered that the contents of an entire oil field have been excluded from recovery by invading waters, some idea of the amount wasted may be gained. Similarly, enormous quantities of gas have been lost underground. Conservation of the oil, therefore, should start before it is brought to the surface rather than after it is placed in storage tanks. Water is one of the most important causes for underground losses and the operator should give as serious consideration to an underground flood of water as he would to a destructive surface flood. The best insurance, of course, is to have the wells drilled in such a manner that water has no access to the productive oil and gas horizons, and on abandonment the wells should be properly plugged. The encroachment of edge water and the occurrence of water in the base of an oil sand present a very serious problem to an oil company; sooner or later these waters are bound to cause considerable damage, if they do not entirely destroy the possibilities of further production. Too often, however, a field has been considered to be in a hopeless condition, whereas wells in as bad a condition in other areas have been repaired and the life of the field appreciably lengthened. The corrections are very often suggested by technical study. Very successful results have been accomplished by detailed underground work in the California oil fields, in Cushing, Oklahoma, and in other areas.

Jan 9, 1920

By V. H. Gottschalk, R. S. Dean

In the theoretical study of metallurgical reactions, it is necessary to make certain assumptions concerning the nature of metal-gas systems. The assumption usually made is that the reaction in such systems takes place predominantly with gas that is in "solution" and that the amount of solution follows the rules which have been developed for aqueous solutions; namely, Henry&apos;s law. The purpose of this paper is to inquire whether these assumptions are the best ones that present knowledge of gas-metal systems permits us to make. In the first part the extent to which a gas will dissolve in a metal and still follow Henry&apos;s law is considered. The conclusion is believed justified that the number of molecules of gas that can dissolve in a metal and have the system follow Henry&apos;s law must be small indeed. It is therefore improbable that the first assumption concerning the predominance of these dissolved molecules in reaction is correct. It is suggested that some improvement in the correlation of the probabilities with the assumptions made in the mass law equations would be made by the use of the dp law of Sieverts in place of Henry&apos;s law. However, the amount of gas that may be held in a metal so that it follows either Henry&apos;s or Sieverts&apos; law is considerably outweighed in most metallurgical reactions by that held in gas-metal systems of entirely different structures and concerning which little experimental evidence is available. Some speculation concerning the nature of these is offered. The conclusion is that attention should be given to the determining of the nature of gas-metal systems and that the really fruitful application of the mass law and its connected calculations will have to await a more complete knowledge of these systems than we now possess. DISCUSSION (Paul D. Merica presiding) P. D. Merica, New York, N. Y. (written discussion).—The solubility relations of gases in metals, in so far as they are known from the pioneer work of Sieverts and others, have from the first presented certain challenging peculiarities. The authors have emphasized the significance of these characteristics and suggest that they point

Jan 1, 1933

By Robert Bakish

VARIOUS aspects of structure-sensitive corrosion of single crystals and polycrystalline aggregates of Cu,Au have been presented in papers by the author, in association with W. D. Robertson. Prompted by some observations in the course of these studies, a new approach to the problem was undertaken. Results of these new experiments are reported here. Thin slices, less than 2 mm thick, were prepared from single crystals 3.5 mm in diam grown by the Bridgman technique. The crystals were homogen- ized for 300 hr at 850°C. Crystals with no deformation, crystals deformed in tension to the yield point, and crystals deformed 20 pct in excess of the yield point were used. Crystals of several different orientations were studied. Slices were immersed for one month in 2 pct aqueous solution of FeCl3 and, subsequent to this immersion, were subjected to bending. Immersion and bending were carried out at room temperature. The size and geometry of the crystals did not permit accurate data on the loads involved. A most unexpected result was obtained in the process of bending these slices of Cu3Au crystals normal to the (110) plane. Completely brittle be-

Jan 1, 1958

By E. L. Spain Jr. N. A. Rose

This study was undertaken primarily to determine the reasons for certain variations in the soundness of gravel aggregate taken from a number of widely separated points on the Tennessee River. Under laboratory tests, concrete made with these various aggregates in some cases exhibited marked differences in specific gravity. crushing strength and durability. Gravel was studied in detail from Chattanooga to the mouth of the river and to a lesser extent from Chattanooga to Knoxville. The causes of variation were determined, and variational curves were constructed, which accurately predict the composition of aggregate at any point on the river and therefore its relative suitability for use in concrete. The aggregate at any point is suited for making sound concrete; the variance of suitability is due to varying percentages of sandstone and weathered material, which are less sound than other constituents. Introduction When it is stated that the aggregate from one point is inferior to that from another, it must not be construed to mean that the gravel is unfit for use. The classification upon which such aggregate ratings are based is largely arbitrary, thus inferiority or superiority is merely relative. Samples of gravel were selected from stockpiles at the dams of the Tennessee Valley Authority under construction, from the stockpiles of private companies along the river, and from samples taken by the gravel-exploration barge of the T. V. A. One hundred or more gravels of each size studied were selected at random by taking small handfuls while walking around the piles. These were separated according to the different mineral or rock constituents present, and the percentage of each constituent was obtained by counting. At least three such samples were taken from each size, and all checked with one another within a few per cent. The results were then averaged. In order to check on the accuracy of such sampling, a whole sample was taken from one point after the gravel was thoroughly mixed. The two methods gave approximately identical results. Sources and Types of Materials The sources of gravel found in the Tennessee River are numerous and varied. The river itself traverses several geologic provinces, each

Jan 1, 1938