Search Documents

THE developments in construction and operation of the basic open-hearth furnace that have taken place in recent years have placed new emphasis on the vital influence played by regulation and control of the combustion system in both furnace production and furnace life. The several factors influencing flame development, such as regulation of fuel supply, air supply, air preheat, furnace draft, and furnace reversal, must be controlled closely if successful furnace performance is to be accomplished. Rugged instrumentation of distinctive design is required to supply dependable information concerning operating conditions, which is requisite to proper regulation of combustion. This chapter attempts to give a practical discussion of the various features of open-hearth practice and instrumentation related to the efficient heating of the furnace, control of temperature, and protection of the furnace structure from accidental overheating. The appended references will be helpful to readers wanting a more detailed treatment of individual topics. OPEN-HEARTH FUELS The most important open-hearth fuels are listed in Table 4-1 together with their compositions and other data useful for combustion calculations. A detailed discussion of open-hearth fuels is not attempted here, but certain factors peculiar to their application to this type of process are briefly indicated on the following pages. Very often an open-hearth shop is forced by economic factors to use a fuel to which its furnaces are not very well adapted, because the general fuel-allocation scheme for the works as a whole seems to demand it. Often a variable marginal supply of coke-oven gas or tar must be consumed by the open hearth, together with another fuel such as producer gas, natural gas, or oil, to fill out total requirements. Most furnaces employ more than one kind of fuel during their usefu1 life; however, the partial redesign

Jan 1, 1951

By J. E. Castle

THE title of this article is descriptive, but not complete, for psychological evaluation is almost as important as rigid economic evaluation. This refers to those human traits that cause people to be too optimistic about the projects they are sponsoring, to overlook obvious weaknesses, to base decisions on incomplete and inaccurate data, and to gloss over embarrassing problems. Investment of capital in a new industrial mineral project is warranted only after rigorous economic analyses based on unquestionable facts. A plunge into production cannot be justified solely because these minerals have been deposited in the ground and are therefore free. There are no specially favorable economic laws that make the business of industrial minerals more attractive than any other. The factors of supply and demand, marketing, technological changes, taxes, competition, and fluctuating prices apply as much to industrial minerals as to other business enterprises. What is more, industrial minerals are subject to the higher risks that all mining enterprises face.

Jan 6, 1958

By C. E. Sims, C. A. Zapffe

MANY hundreds of publications have appeared during the past 78 years that treat the subject of hydrogen in iron and steel,105 but conclusions regarding the functions of hydrogen in causing some important defects in steel are still unsatisfactory to many; and other hydrogen-caused phenomena yet remain to be identified with this gas. The most widely discussed of these defects is hydrogen embrittlement, but the conception, perhaps the popular one, that embrittlement is due to hydride formation does not conform to the known facts.104 The true identity of hydrogen embrittlement seems instead to lie in a mosaic nature of metal crystals, which is a concept not yet accepted by most metallurgists. A study of hydrogen embrittlement therefore provides new viewpoints in regard to the crystalline substructure of steel. A second widely discussed hydrogen-caused defect is the "flake" or "shatter crack." Although it is generally agreed that the presence of hydrogen is a prerequisite for their appearance, it is also realized that internal stress plays a decisive part. The relationship of hydrogen to internal stress has not been explained very clearly; nor is it always clear what the relationship is between a "flake" and a "snowflake," or between a "fish eye" and a "shatter crack." More importantly, the relationships among hydrogen embrittlement, hydrogen-caused fissures such as "flakes" and the ultramicroscopic structure of steel have scarcely been recognized. The present investigation attempts to provide an explanation for the embrittlement of steel by hydrogen by showing cause for accepting the "block" concept of metal crystals, and then to show how the numerous hydrogen-caused defects are interrelated in the light of this concept. EVIDENCE OF SUBSTRUCTURE IN METAL CRYSTALS It appears that the concept of a crystal as an aggregate of smaller multi-atom units must be accepted in some form if the behavior of metals is to be understood. The abundant literature on the evidence of an ultramicroscopic "mosaic" structure in metals and other crystalline substances suggests that the physicist has provided the metallurgist with an invaluable new insight. The exact picturization that any one physicist provides may be open to question, but the fact that there is some such fundamental substructure seems undeniable. The present work makes no pretense of comprehensively treating the imperfection structure theories. Nor will conclusions be drawn here regarding the exact nature of the substructure of crystals. However, the acceptance of some imperfection theory of fundamental attributes seems so necessary to an understanding of the behavior of hydrogen in steel that the following brief

Jan 1, 1941

By G. R. Mansfield

THE third year of Government exploration for potash by the U. S. Geological Survey and the U. S. Bureau of Mines under the authorization of the act approved June 25, 1926 (Public 424-69th Cong.) is drawing to a close. The results thus far obtained are thought to be sufficiently interesting and satisfactory to justify the presentation of a brief pre¬liminary account of the work. REVIEW OF EARLIER EXPLORATION The general geologic similarity of the Permian basin of Texas and New Mexico to the potash field of Germany had long ago suggested the possibility of the presence of potash salts somewhere in that basin, but petroleum exploration was then making little headway there and the necessary data could not be obtained. The discovery by Udden in 1912 of potash in brine from the Spur well in Dickens County, Texas, was the first direct evidence of its presence. In 1915-17 the U. S. Geological Survey drilled a test well with standard tools at Cliffside near Amarillo, but failed to find potash. Nevertheless, an observer has been kept in the field, at first in cooperation with the Texas Bureau of Economic Geology but since 1922 by the Survey alone, to secure data and samples from oil and gas tests. Since the discovery of oil in Reagan County in 1923 exploration by drilling has been rapidly extended to many parts of western Texas and southeastern New Mexico. The identification of the potash-bearing mineral polyhalite was first announced by the Geological Survey in June, 1921, the material having come from cuttings from the Bryant well in Midland County and the Burns well in Dawson County, Texas. Successive discoveries and announcements of similar purport aroused widespread interest in potash exploration, which culminated in the action by Congress already noted.

Jan 1, 1929

Jan 1, 1902

By L. S. Darken

It has long been recognized that the driving force in an isothermal diffusion process may be regarded as the negative gradient of the chemical potential (partial molal free energy) of the diffusing substance. This equivalence is exactly analogous to the fact that a mechanical force is the negative gradient of the potential energy. Nernstl in 1888 expressed these driving forces in terms of osmotic pressure, which is directly related to the chemical potential and free energy. The relationship between the diffusivity, mobility and activity coefficient of electrolytes in aqueous solution has been developed in great detail by Onsager and FuossZ with results which have recently been confirmed experimentally by Harned and Nuttall. This interpretation of the driving force in isothermal diffusion has been discussed earlier by the author,4,5 who pointed out4 that "for a system of more than two components it.is no longer necessarily true that a given element tends to diffuse toward a region of lower concentration even within a single phase region"; departure from the behavior of an ideal solution may be so great that the concentration gradient and the chemical potential gradient, or activity gradient, may be of different sign, thus giving rise to "up hill" diffusion. Since, in the discussion of that paper,4 some skepti- cism as to the validity of this conclusion was expressed, it seemed desirable to adduce experimental evidence to support it. Evidence of such diffusion in nonmetallic systems has already been reported. For example, it was observed by Hartley" in a series of experiments in which sodium chloride diffused from a saturated solution in about 5 pct acetone in water into a solution virtually free of salt but with essentially the same acetone concentration. Specifically, a wine glass containing crystalline salt and saturated solution was totally immersed in a large glass cylinder containing the acetone-water solution without salt; the difference in specific gravity was such as to prevent convection. Diffusion of salt was accompanied by a marked depletion of acetone in the wine glass; after 3 days the acetone concentration decreased from 5.37 pct at the top of the glass, where the salt concentration was low (0.93 pct), to 1.84 pct at the bottom where the salt concentration was high (21.64 pct). This "uphill" diffusion was found to be such that the partial pressure (activity) of acetone was essentially equalized throughout the system when a steady state gradient of sodium chloride was maintained. In order to demonstrate the existence of such diffusion in metals, a series of four weld-diffusion experiments was made. In these measurements pairs of steel of virtually the same carbon content, but differing markedly in alloy content, were welded at the end and held at 10500 C for about two weeks. Subsequent analysis showed that carbon had diffused so as to produce an inequality

Jan 1, 1949

By T. M. Barry

HOW often have those who make mining a career said that, "mining is different"? This kind of feeling often expresses itself in talking shop with men of other industries. And there is no doubt about it; mining is different. There are different marketing problems, different production problems, and we certainly have different personnel problems, to cite but a few. Mining people have recently been discovering though, that many of their problems are not unique to mining. They are beginning, in fact, to find that many of them are dead ringers for problems that other industries have had to face and solve years ahead of mining.

Jan 6, 1954

By L. S. Darken

In the study of reactions occurring in liquid iron, alone or in contact with a liquid oxide or slag phase, it has been found that the experimental data over a limited range of concentration can in some cases be represented satisfactorily by the simple equilibrium expression where (P) denotes the concentration of a product and (R) the concentration of a reactant in the reaction r1R1 + r2R2 + • • • D P lP1 + P 2P2 + • • • Some of the reactions for which it holds are listed in Table 1. For others, however, the simple equation apparently does not hold. This has been attributed to an improper method of expressing concentration (for instance, weight per cent instead of mol fraction); or it has been supposed that the solutions are not ideal in the sense that the activity of a component is not proportional to its true mol fraction. But it may be that the problem has been oversimplified by neglecting some molecular species actually present; that is, by considering only the ostensible simple components and thus leaving out of account possible compound formation. It is the purpose of the present paper to point out how, in a group of related cases, a reasonable consistent assumption relative to the presence of a compound makes it possible to express the experimental data satisfactorily by the simple equilibrium expression when this compound is taken into account, and to bring into harmony data referring to different reactions in liquid iron. There are several a priori reasons for believing that solutions in liquid iron should not deviate far from ideality, provided that the concentration of solute is not too great and is expressed in proper terms. The factors that commonly lead to nonideality in systems at ordinary temperature— as ionization or the occurrence of polar and nonpolar molecules—are presumably less effective in inetal and in slag systems at high temperature. Again, the type of equation commonly used to express the value of

Jan 1, 1940

By Horace Pops

Isothermal sections in the copper -rich region of the Cu-Si-Zn a1by system have been determined at 8473 760; 6003 and 482°C by means of microscopic examination with confirmatory X-ray diffraction work. The stability of the bee 0 phase decreases both with decreasing temperature and with increasing copper content. The silicon-n&apos;ch 0 phase decomposes upon quenching from high temperatures either by a martensitic or by a "massive" transformation, depending upon the solute content. A two-phase equilibrium is found to exist in the Cu-Si-Zn system between the hep < phase of the Cu-Si system and the bee ß phase of the Cu-Zn system. It is shown that the isothermal limits of the primary solid solution at 760; 6003 and 482°C are in part affected by the intermediate phases which follow them in the ternary system Possible electron-concentration and size effects upon phase boundaries are discussed. ALTHOUGH the mechanical and physical properties of silicon brasses have been measured in great detail, the factors which influence these properties are not well-understood, partly because the knowledge of the phase relationships in the Cu-Si-Zn system is limited. Gould and Ray1 studied the effects of silicon upon the hardness and structure of Cu-15 pet Zn and Cu-40 pet Zn alloys. They proposed an isothermal section at 800°C which was not based upon experimental data, since the binary phase diagrams had not been completely determined. Using Cu-Si-Zn alloys containing approximately 5 wt pet Si, vaders2 determined the boundary, at 750°C, between the copper-rich solid solution and an unidentified second phase. Masing and wallbaum3 examined a vertical section through the ternary diagram in the region between Cu-20 pet Zn and Cu-10 pet Si alloys, but they emphasized uncertainty about their data. Mima and Hasegawa4 studied the liquidus surface of Cu-Si-Zn alloys, phase transformations in high silicon-bearing (20 to 25 at. pet) alloys,5 and the phase relations in low silicon-bearing Cu-Si-Zn alloys.6 Their experiments were based upon thermal analyses and metallographic observations. The compositions of the phase boundaries were not determined with high precision, and the crystal structures of the phases were not reported. Because of uncertainties in the existing literature, it became of interest to determine more accurately the phase relations in copper-rich Cu-Si-Zn alloys. The crystal structures, stability, and phase boundaries of the primary solid solutions and several intermediate phases were determined, and the data are reported as partial isothermal sections.

Jan 1, 1964

By William Kent

I DESIRE to place on record in our Transactions a recent innovation in blast-furnace practice, namely, the introduction at the Lucy Furnaces, in Pittsburgh, of four water-tube steam-boilers, of the Babcock and Wilcox pattern, aggregating 832 horse-power, builder&apos;s rating, or 9,568 square feet of heating-surface, utilizing the waste gases of the furnaces as fuel. The boilers are set in two batteries, each of 416 horse-power, and each battery occupying a ground-space of 22 feet 7 inches by 20 feet 4 inches. The accompanying dram-

Jan 1, 1885

By T. B. Armstrong

Electrical energy conservation sees that service facilities are operated only when needed and that production equipment is operated under an optimum condition. Specific energy consumption (kw-hr per tonne) is not regularly recorded for comminution circuits because of variations in ore characteristics and the low grinding efficiency (0.1 to 2.0%) of the equipment. Improved data acquisition can produce meaningful results. Particle size monitor systems and density gauges permit comparison of energy (kw-hr) and production (tonne) for a "fixed" condition. Finding the operating condition producing the lowest unit energy consumption provides a target for an effective energy management program.

Jan 1, 1982

Mellon Institute of Industrial Research, University of Pittsburgh, Pittsburgh, Pa. The Mellon Institute of Industrial Research has carried on for years research and investigations for all type and manner of indus¬try. One of the provisions of the foundation of the Institute is the

Jan 1, 1933

Jan 1, 1969

By J. Henry Harden

I desire to call the attention of the Institute to a new form of drawing-board trestle. With the ordinary four-legged trestle, commonly used, one has not the means of adjusting the height of the board to the draughtsman. To obviate this inconvenience, and at the same time to enable one to incline the board, I have devised an arrangement of curved and straight slots and thumb-screws, by means of which the hoard can be raised three or more inches, and placed at any desired angle of inclination on either side. Figures 2, 3 (Plate I) show side and end elevations of the trestle for a single board, and Figure 4 for two boards. The latter form is adapted for use in schools, or where it is desired to economize space.

By Donald D. Smythe

Tars paper describes briefly the topography and geology of the region where the mica-bearing pegmatites are found and discusses prospecting, the quality of the mica, its preparation, and evaluation of the deposits. Muscovite mica occurs in a number of widely separated localities in Brazil, but production has come largely from deposits in the southeastern and eastern part of the State of Minas Gerais (Fig. I). There the deposits form a discontinuous zone, which starts at a point 90 km. north of the city of Rio de Janeiro and extends north for some 500 km., roughly parallel to the coast. A maximum width of 180 km. is reached along the Rio Doce. To the west in Minas Gerais, and extending east into the states of Espirito Santo and Rio de Janeiro, the mica zone proper is fringed by areas in which there are scattered occurrences of mica-bearing pegmatites. A few of these outlying deposits have produced commercial mica, but most of them are unimportant. To the southwest, in the State of São Paulo, there are a number of mines, which at one time produced a very considerable amount of sheet mica, largely as a by-product of kaolin mining. These deposits, and, a few others lying between them and the main productive areas to the northeast, appear to be the southwestern continuation of the strong Minas Gerais mica zone. In the vicinity of Conquista, just north of the Minas Gerais boundary in the State of Bahia, and still farther north, near Jacobina, there are several known mica deposits. Their location indicates that they may be the northern continuation of the main mica zone. The major part of Brazilian mica production has come from four areas within the mica zone proper; from north to south, Governador Valadares, Raul Soares, Espera Feliz, and Muriaé. The first is 190 km. from north to south and reaches a maximum width of 180 km. The Raul Soares area extends 135 km. from northeast to southwest, and in places is 80 km. wide. The Espera Feliz area is 100 km. from north to south, and reaches a width of 35 km. The Muriaé area extends 150 km. from northeast to southwest and its width reaches 40 kilometers. Between the known productive areas, and in the areas directly to the southwest and to the north of them, little mica has been produced. These gaps, as well as certain irregularities in the outline of the mica zone itself, are to be ascribed either to lack of prospecting or to conditions preventing the discovery of mica, rather than to its nonexistence. Elsewhere in Brazil mica has been reported from eastern Goiaz, Ceará, Pernambuco, Rio Grande do Sul, Matto

Jan 1, 1946

By G. S. Coe, G. F. Bolling

The columnar-to-equiaxed transition (CET) has often been studied as a function of concentration, C, temperature gradient in the melt, G, and rate of solidification, R. Although it may not be immediately obvious it is sure that the CET, expressed as some ratio G/R necessary to suppress equiaxed nucleation for a given C,&apos; cannot be a single-valued function of C. This restriction which is ignored in theoretical presentations is most trivially illustrated by the following simple reasoning. An ordinary casting is an unconstrained system where the thermal conditions change continuously with progressive solidification, and thus where the ratio G/R decreases from the outset. A CET occurring early in a casting (much equiaxed material) must then mean a higher value of G/R at transition, in comparison with the late CET which implies a more columnar ingot. Therefore, when we choose to experiment under constant superheat for all alloys across the simplest binary, and we find an inversion in the amount of equiaxed material, we shall find two values of C satisfying the G/R condition. However, in addition to this simple instance, the early experiments of ~orthcott&apos; seem to show that the amount of equiaxed material in cast ingots may be a multivalued function of composition in a given binary system. In the present investigation, the CET has been examined in Pb-Sb, Pb-Ag, Pb-Sn, and Sn-Pb under several types of casting conditions. First, we have used the "bidirectional" ingot section Simulation;~ and we have used .&apos;i~z situ" ingot solidification where a hot mold already filled with liquid is chilled so that there is no disturbance provoked by pouring. Differences in method are trivial to our purpose except for the fact that certain variations are more simply observed by one technique than by the other. Second, we have varied the mode of superheating from the simple extreme of casting all alloys from the same temperature regardless of composition to the careful casting at a standard superheat, calculated with respect to the alloy liquidus. Third, we have made provisions for decanting and interface observation, so that some "castings" were not completed. The results obtained with Pb-Sb are exemplary; some of these are shown in Fig. 1 along with explanatory captions. At 9 to 10 at. pct Sb, and thus above the solid-solubility limit Cs = 5.8 at. pct Sb and yet below the eutectic concentration Ceu = 17.5 at. pct Sb, there is a persistent anomaly in all the variations. Measurement was easy enough and standard enough so that we may forgo discussion of either method or possible error, in view of the forceful self-consistency shown by experiment. Solute distributions were measured along the bidirectional ingots in order to determine if a solute buildup had occurred at the CET. No anomalous changes in concentration were observed along the bars at either side of the solute anomaly of 10 at. pct Sb. The microstructures of the ingots were also examined across the range of composition investigated. At concentrations less than 9 at. pct Sb the micro- and macrostructures were typical of the cellular-dendritic growth usually reported for the columnar zone. Above the anomaly, both the columnar grain size and the amount of primary phase decreased. This microstruc-tural observation can be correlated with observations made of decanted interfaces. Below 9 at. pct Sb, the interface reveals the "normal" columnar dendritic structure; however above the anomalous concentration range, preferential growth of certain dendrites appears to form a "super dendrite" pattern. In Fig. 2 a microstructural view of the etched &apos;(super dendrites&apos;&apos; shows their constitution both in terms of relative phase proportion and in terms of the ordinary smaller dendrites.

Jan 1, 1969

By T. D. Murphy, G. V. Henderson

The element silicon, with its usual partner, oxygen, plays the same role relative to inorganic materials as carbon and hydrogen play with respect to living organisms. The crystallographic structure of silicon dioxide (SiO2) consists of one atom of silicon well-nigh inseparably bonded to four contiguous atoms of oxygen, a gas of but slightly more than half its atomic weight, forming a three-dimensional network of SiO4 tetrahedra (Dietz, 1968). This wispy arrangement is the fabric of the mineral quartz which is one of the harder, more abrasive, and chemically stable raw materials to be found in Mother Nature&apos;s cupboard. Most of us are vaguely familiar with the observation that nearly 60% of the lithosphere to an approximate depth of 10 miles is composed of these two elements, which proportion actually rises to about 75% if the atmosphere, hydrosphere, and biosphere are included (Parker, 1967). Elemental silicon is a brittle steel-gray metalloid with a density of 2.42 and does not occur in nature. In its limited commercial form, which is still brittle and metallic in appearance, its density drops to 2.33. It combines with oxygen to form the gaseous oxide SiO, or the solid dioxide Si02 (analogous to its congener carbon in CO and CO2); a tetrachloride SiCI4 (analogous to CC14); or, combining with oxygen and one or more metal ions, forms the largest rock-making family of all, the silicates. Further, next to the feldspars, quartz is the most abundant known mineral and, in some form or another, accounts for roughly 12% of surficial terrestrial rock. It is this so-called "free silica" to which your attention is chiefly directed in this chapter. In any such consideration of silica, its several crystalline phases with their attendant differing physical properties appear worthy of delineation. Alpha quartz is the only one of this interesting polymorphic family that is thermodynamically stable at normal pressures and temperatures up to about 573°C. The low phases of tridymite and cristobalite can exist in the so-called metastable state below 117° to 200ºC but seldom occur in nature in these two different crystal forms (Sosman, 1965). Opaline silica, now considered by most researchers to be a variety of cristobalite, occurs in abundance and is the only exception. The three remaining polymorphs, keatite, coesite, and stishovite, also are metastable under ambient conditions. Keatite, however, is not known to occur naturally and has only been synthesized in the laboratory. The other two have been identified in submicron sizes and in microscopic amounts, occurring naturally as a result of high order shock-wave pressures generating quite elevated temperatures --such as might accompany the impact of a large meteorite on a hard sandstone terrain (Chao et al., 1962). An intriguing characteristic of these silica minerals, and one which has very practical applications, is their extremely variable densities. The classic 2.65 specific gravity of alpha quartz drops to 2.20 in tridymite, cristobalite, and lechatelierite (natural silica glass), as well as in many man-made glasses of commerce which are merely noncrystalline or amorphous solids in the form of super-cooled liquids which can no longer change their shapes (Pauling, 1950). It rises again to 2.50 and 2.93 for keatite and coesite, respectively, and finally becomes a reported 4.35 for stishovite-nearly a 50% range in density for the known physical combinations that silica naturally assumes (Frondel, 1962; Konnert et al., 1973; Pecora, 1960). Pursuing its esthetic aspects, briefly, silica is well-represented among gem stones which, to qualify as such, must have the attributes of beauty, durability, and rarity (Jahns, 1983). As quartzose gems usually have but one or, at

Jan 1, 1983

By J. D. Meakin, H. G. F. Wilsdorf

Using a combined decoration and etching technique the dislocation structure of annealed and deformed a brass has been studied. Annealed crystals revealed a low density forest and well-developed subboundaries; lightly deformed crystals contained discrete groups of dislocations. The dislocation density and the number of dislocations in a group were obtained from the micrographs. Using slip-line data, the mean path of a dislocation and the configuration of groups along an active slip plane have been deduced. Observations on secondary and cross-slip are reported. It has been the aim of many investigations to obtain detailed knowledge of the dislocation patterns which are present in metals before and after their deformation. The "decoration" of dislocations with impurity atoms has been considered as one of the promising experimental approaches, and much work has been done to develop this technique for revealing dislocation sites in metals. Following the early work by Castaing,&apos; Castaing and Guinier,&apos; and Lacombe and Berghezan~ on aluminum-rich aluminum-copper alloys, dislocations in this material have been studied extensively by others.+&apos; In these alloys the dislocation sites act as nuclei for the precipitation of the second phase. The main results of the investigations on aluminum with copper are: i) the confirmation of the earlier contention that subboundaries consist of dislocation walls, ii) that many more dislocations are found in slip bands than in regions where less glide had taken place, iii) the observation of individual dislocations, lying nearly parallel to the surface investigated, and iv) that parts of dislocation loops, apparently emitted from a dislocation source, could be made visible. Recently, Jacquet, Weill, and Calvert have succeeded in revealing nearly concentric dislocation loops in quenched A1-4 pct Cu and thus indicated directly the existence of dislocation sources in a fcc metal specimen of normal dimensions. Another decoration method developed by Dash10&apos;11 and applied to silicon crystals makes use of diffusing copper to the dislocations from a surface deposition. The dislocation pattern can then be observed by an infrared technique. His results include evidence for symmetrical and spiral Frank-Read sources, and for arrays of dislocation loops which follow simple crys-tallographic directions. Recently Low and Guard" have studied the dislocation structure of silicon-iron using carbon for the

Jan 1, 1961

By T. B. Massalski, C. S. Barett

THAT metals and alloys of the body-centered-cubic structure tend to become unstable at low temperatures is so nearly universal that any exceptions are worthy of special attention. Studies of the exceptions may disclose unrecognized examples of metastability or may shed light on the nature of some of the factors that stabilize the body-centered-cubic phase. Among the structurally analogous body-centered-cubic 3/2 electron compounds, the ß-phase in the Cu-Zn system deserves further attention for, although this phase is known to undergo partial mar-tensitic transformation on cooling below room temperature to the temperature of liquid nitrogen when the composition is less than about 42 wt pct Zn, it does not transform on cooling .when there is more than this amount of zinc present.1-4 The present authors recently found that an alloy containing 48.35 wt pct Zn could be transformed, however, if deformed severely at room temperature or lower temperatures.V his discovery led to the suggestion that the jerky flow of ß-brass single crystals6 and some of the unusual temperature variations of the yield strength and hardness are due to strain-induced transformation during the tensile tests. The present investigation is an extension of that work to cover the entire available range of compositions of Cu-Zn ß-phase alloys and certain interesting compositions of the ß-phase in the Cu-Zn-Ga system. Particular attention is given to the structure of the transformation product resulting from cold work, which is found to vary with alloy composition, and to the temperature range in which transformation can be induced in the various alloys. The composition limits of the body-centered-cubic phase in the Cu-Zn system, based on a recent review by Raynor7 and the precision determinations of Beck and Smith: are shown in Fig. la; in the ß region the alloys are disordered and in the ß region they are ordered. The rate of ordering is so rapid that a high degree of order is found in any of these alloys immediately after quenching. Experimental The nine binary and four ternary alloys of this investigation were prepared from cathode copper (99.99 pct purity), electrolytic zinc (99.99+ pct), and gallium (99.98+ pct). All alloys were cast in transparent Vycor tubing, homogenized at temperatures between 800° and 890°C, and quenched in water. Ternary alloys were cast in small amounts (-5 g) to predetermined compositions to fall along a line of constant electron concentration in the ternary system. Changes of weight during the casting operation of the ternary alloys were not greater than 1 part in 2500 from the intended nominal weights and therefore their compositions were accepted without chemical analyses. All binary alloys were cast in larger amounts (100 to 150 g), homogenized, and hot rolled after preheating to 800°C. The central portion of the rolled strip of each alloy was annealed for eight days and quenched in brine. All binary alloys were analyzed chemically. The compositions, heat treatments, and metallographic appearances of all alloys are tabulated in Table I. Various samples were subjected to heat treatment or cold work at several temperatures and were then examined metallographically or by means of X-rays. Specimens about 6x6x3 mm in size were examined metallographic ally to confirm the presence of the ß-phase after quenching. Cold work was introduced by fastening each sample between two pieces of steel, cooling the assembly to the desired temperature, and transfering it rapidly to a vise where moderate or severe compression was immediately applied. Cold working at liquid helium temperature was done by a chisel-shaped tool mounted on an X-ray spectrometer, described elsewhere.% A!! metal-

Jan 1, 1958

The Empire IV expansion is on schedule for completion in January 1980; Hibbing Taconite&apos;s 2.7 million ltpy* expansion should be finished late in 1979; and Reserve Mining&apos;s tailing disposal project is on target for April 1980. Erie Mining Co., the first to bring 170-ton haulage trucks to the Mesabi Range, reports excellent operating results, and Inland Steel expects to produce 80% of its pellets in 1979 using coal rather than oil. One Michigan mine has so many inspectors that it has hired a school bus to transport them around the operation; and a contractor reports that mine construction projects of the future may require the training of 15,000 workers. All of this was covered at the 52nd Annual Minnesota Section AIME Meeting and the 40th University of Minnesota Mining Symposium, a joint event held each January in Duluth.

Jan 3, 1979