Search Documents

By R. M. Schuster, F. M. Benavides

A plan is prepared to develop and operate a four mine complex over a 30-year period. The mining complex is in the vicinity of two existing processing plants and the most economical means of transporting the raw minerals to either or both of these processing plants is sought. The mines and processing plants are all within a radius of 5.6 km (3.5 miles). Existing transportation facilities consist of county and state roads and federal highways as well as haul roads in some areas. A navigable river meanders through the area under study and there are two railroad systems servicing the area. The analysis shows the economic and operational feasibility of using an overland conveyor in lieu of other means of transportation.

Jan 1, 1983

By Steven Mitchell

BACKGROUND Homestake Mining Company began milling operations at the Bulldog Mountain Mine near Creede, Colorado in 1969. The Bulldog Mill, rated at 350 tpd, produces a bulk flotation condentrate assaying about 180 oz/T Ag and 20% Pb, from heads of about 16 oz/T Ag and 2% Pb. The circuit is straightforward with two-stage grinding to 1-5% plus 65 mesh, followed by rougher and cleaner flotation. Reagents used are Z-6, Z-11, Aerofloat 242 and Aero Promoter 404, with an Aerofroth 65-MIBC mixture for a frother. Additional information on the geology, mine and mill are available in references (1) and (2). A flow sheet for the mill and CIP plant together is attached as Figure 1. Final flotation tailings normally vary from 1.5 - 2.0 oz/T Ag. These tailings are cycloned to produce sand for underground backfill. After cycloning, the sands are repulped and given a final scavenger float. This sand scavenger recovers a small additional amount of silver which recycles back to the main flotation circuit. The tailings are recycloned and pumped to the mine or, if the mine cannot accept sand, to tailings. The majority of the silver in the flotation tailings exists in the fine fractions; cycloning upgrades the slimes and lowers the assay of the sand. The sand, after scavenging, typically assays 0.5 oz/T Ag, and the slimes assay about 3.0-3.5 oz/T Ag. From 1969 to 1976 all of the slime tailings and the sand tailings not used underground were impounded in a tailings pond located about

Jan 1, 1983

By Fred D. Fox

INTRODUCTION Approximately two years have elapsed since the first summary of the Grizzly Gulch Tailings Disposal Project was presented (1). Since that time, various physical modifications and additions to the existing treatment system have transpired. Further, Homestake and the entire mining industry have been impacted severely by additional modifications and additions concerning regulatory reform aimed at total disciplinary permitting and hazardous waste management. The following paper summarizes the past accomplishments relating to the Grizzly Gulch Tailings Disposal Project, correlating these accomplishments with future plans that are being developed to comply with regulations and to continue Homestake's commitment to environmental protection. The famous Homestake Gold Mine, located in Lead, South Dakota, has been operating in the Black Hills region for over a century, approximately 12 years before the south half of Dakota Territory was admitted to the Union as the State of South Dakota (2). During the 104 years of operational development, Homestake's Gold Mine, as well as the entire mining industry, have been influenced by numerous governmental regulations dating back to the Refuse Act of 1899 which regulated the deposit of debris from mines and stamp works. The enactment of the National Environmental Policy Act of 1969 may be thought of as the beginning of a long line of unplanned steps to deal with the many concerns of matters pertaining to the environment. Environmental awareness continued into the 1970’s, in which the Clean Air Act, Federal Water Pollution Control Act, Safe Drinking Water Act, Toxic Substances Control Act, and the Resource Conservation and Recovery Act (RCRA), to name a few, surfaced.

Jan 1, 1983

By James P. Savely, Victor L. Kastner

Inspiration Consolidated Copper Company is currently mining in four pit areas; Live Oak, Red Hill, Thornton and Joe Bush Extension, near Globe, Arizona. Small satellite orebodies lying outside the main pits have been mined out in a series of small open pits. Major slope instability has affected production in every pit. Some consequences of the instability have been; (1) Serious interruption of mining plans, which resulted in deferred ore production, lost ore, reduced mining rates and increased stripping requirements. (2) Forced replacement of crushing facilities. (3) Serious effects on other production facilities. The introduction of a slope stability monitoring and control function as an integral part of mine planning has been successful in reducing the impact of these failures and will eventually result in economic pit design based on probabilistic slope analysis. This case history presents a brief review of the problems associated with slope instability at Inspiration's mines followed by a more detailed report on one specific failure area in the Thornton pit where the use of horizontal drain holes for slope stabilization appears to be successful. Relationships between slope movement rate, rainfall, and mining activity are shown.

Jan 1, 1983

By G. D. Marshall, D. K. Sarin, V. E. Hampton

Ground support at the Thompson Mine emphasizes scaling, rock bolting and wire mesh screening on the backs and walls of all underground stoping and development areas and also full column grouted cable bolting in the bulk mining areas. This paper describes the equipment for the point anchored rock bolts as well as the full column cable bolts. Modifications in design and testing of all components and procedures has ensured a safe and efficient method of ground support for the mining conditions existing at the Thompson Mine.

Jan 1, 1983

By Ma Guang, Huang Jinshou

In this paper we briefly describe measuring techniques and their practical use in the mining industry of China. A strain coefficient matrix of triaxial strain cell for a flat ended borehole is also introduced.

Jan 1, 1983

By John T. Wizzard, R. P. Killmeyer, B. S. Gottfried

The Coal Preparation Branch of the Pittsburgh Energy Technology Center has developed a computer program to calculate the performance characteristics of coal washing devices. This program uses specific gravity analyses of the clean coal and refuse streams as input, and generates dependent and independent performance criteria for the washer. Partition curves are internally represented in a functional form by a Weibull function. Performance criteria generated by this computer program are compared to manually calculated performance criteria for air tables, Dynawhirlpools, Baum jigs, hydrocyclones, and dense medium cyclones. The comparisons show that the computer program gives results in close agreement with the hand- calculated values while greatly reducing the amount of time involved in performing the analyses.

Jan 1, 1983

By Victor J. Miller

The Northeast Tripp Slide is one of the larger slope failures that can be attributed to open pit mining. It is a 11.7 million cubic meter (15.3 x l0 6 yd3) wedge failure created by two thick gouge-filled fault zones whose intersection plunges into the Tripp pit at 13°. One unique aspect of this failure is that the slide is now stable despite having moved an estimated 8.5m (28 ft.) towards the pit and having reached a maximum overall velocity of 2lmmlday (0.07 ft/day). The slide started to fail in 1968, accelerated until mining in the slide's toe area was halted in April 1970, then began to decelerate. With the cessation of mining in the toe area, rubblized rock sloughed into the pit bottom which added weight to the failures toe constraints and began the stabilization process. Measurements from a network of survey stations revealed a correlation between the slide's velocity and heavy precipitation. Runoff water accumulating in the tension cracks is believed responsible for this correlation. Moreover, the survey net measurements showed that during the failure's last stage the vertical component of the slide's movement greatly increased. It is proposed that this settling was caused by plastic-like flowage of the clay gouge underlying the failure The fault zone's effective shear strength was estimated by a back- analysis on the wedge's geometry and by performing direct shear tests. The tests, performed on cores taken from samples that were collected on the failure, yielded a residual shear strength of: cohesion 0.61 kg/cm2 (8.7 lb/in2), and a friction angle of 9.6°. This residual shear strength was near1y equal to the back-calculated strength indicating that the controlling fault's effective strength was essentially the same as the residual shear strength of the gouge filling

Jan 1, 1983

By Nath S. Parate

Emphasis on publications related to coal mining subsidence and damages is appropriate at present in view of the energy crisis and increased coal production and public alertness. I have worked in Harrisburg with the state government Public Utilities Commission on energy-fuel matters and issues (Parate, 1978-80). I have participated in the communication on subsidence/ damage reviews and status with the Bureau of Mines Liasion Office (Kebblish, 1978-79). I have done research (Parate, 1965) and published papers (Parate, 1972; Parate, 1967) in Britain on coal mining subsidence and damages around Sheffield-Nottinghamshire coal fields. I have a few comments on the recent paper titled, "Pennsylvania Subsidence Control Guidelines," by C.J. Bise. 1) What is the basis of the empirical formula or guideline, LD _ (0.27 x D) ± 4.6, defining the support area? 2) The particular structure may not be damaged due to vertical uniform displacement caused by mining beneath unless the displacement is differential (King, 1964). 3) The author mentions the limited subsidence research in the US, and quite rightly so. But he fails to quote any work reference by continental investigators except the British or review work by the US. What are the reasons? 4) The author has not mentioned the importance and role of angle of draw for Pennsylvania, Kentucky, or Illinois coal fields. Is there any current research investigation on the relationship between subsidence research investigation, damage, and transference of strains to structures? There have been a number of newspaper reports on subsidence damage in Wilkesbarre and other areas in Pennsylvania. Is the author aware of such instances and traditional attitudes to such issues? Many times government agencies--due to lack of funds, technical expertise, and public policies--are unable or do not find it interesting to keep updates on these issues, as per the author's knowledge and experience with state governments. 5) What is the net effect and role of the D.E.R. Insurance Office on the monitoring, reducing, or controlling subsidence damage, particularly in Pennsylvania?

Jan 1, 1983

By Brian R. Castle, James J. Scott

INTRODUCTION Referring to a ground support system as a 'band-aid' borders on getting cute, but the application of cable slings in U.S. mining is somewhat analogous. Where problems in the roof or rib require additional support, the versatile cable sling is the answer in a variety of conditions. To fully understand how and why cable slings are used today we must briefly review their development history. Much of the thrust over the last five to seven years in ground support fixtures has been the development of hybrid systems. Taking the best of two or more existing roof bolt fixtures and marrying them into a new fixture which exhibits the good characteristics without the bad of the parent systems. Resin point anchored mechanical bolts, continuous threaded rebar bolts, and others have all be- come important fixtures in rock mass stabilization. HYBRID GROUND SUPPORT SYSTEM The cable sling system is also a hybrid, both in its parentage and in its ground support characteristics. See figure 1. Cable slings combine the techniques of cement. grouting high-strength cables, Friction Rock Stabilizers, and truss-like suspension into a versatile and high- strength ground support system. 1/2" high-strength cable is cement grouted in place in a manner similar to pre-

Jan 1, 1983

By Richard Kunter

INTRODUCTION Additional work has been done on the CIP circuit at Creede, and a brief description of this work is presented in this paper. DREDGE The original dredge for the Bulldog was built by Al Hack, Inc. of Denver. The dredge cutter head is mounted on a boom made of 6-inch diameter pipe which is raised and lowered by a cable-pulley system. Maximum cutting depth is 8 feet. Slurry from the dredge flows through a floating 6-inch diameter pipe supported on 55-gallon drums which runs from the dredge to the shore and then to a trash screen and pumping system. See Figures 1 and 2. The cutter head, suction pump, winches for dredge movement, and all other operations are controlled from a small operations house located toward the rear of the dredge. All of the basic dredge equipment is mounted on a chassis about 8 ft x 16 ft in size. Additional buoyancy was originally provided by sealed 55-gallon drums supported along the sides of the chassis by a small wooden framework. Additional framework and barrels on the front of the chassis on either side of the cutter boom provided additional stability, particularly when digging in hard material. The dredge was quite stable, but two problems were apparent. For one, it could have been sunk by someone from the shore firing a rifle into all of the barrels. In prime deer-hunting and sportsman country

Jan 1, 1983

By F. C. Foshag, P. E. Wingrove

The Kayford, Boone and Nicholas Division of Bethlehem Mines Corp. operates a modern coal preparation plant in Van, WV. Since start-up of the Van plant in 1976 until the summer of 1980, the refuse handling system proved to be a costly maintenance problem and a material handling bottleneck. During the 1980 two-week miners' vacation, the original system - which included two screw conveyors and a drag conveyor - was replaced by an installation using two Flexowall steep angle belt conveyors. This paper describes the technical and economic analysis that led to the new installation and reviews its first year operating performance.

Jan 1, 1983

By C. Chamberlain

The Telfer Project, Australia's newest, largest, and most remote gold mine treats 480 kt of ore grading 9.33 g/t derived from open pit mining operations. Coarse gold is recovered by gravity concentration with jigs and further upgraded wing a continuous strake launder table, and by amalgamation. Remaining gold is recovered in a cyanide circuit and incorporates flat bottom air agitators, counter current decantation (CCD) and stellar filters for clarification and precipitate removal. Overall recovery into a bullion averages 98%. The mill incorporates a number of design features that allow for maximum efficiency and security wing a minimum number of operation personnel.

Jan 1, 1983

By Peter N. Calder

This paper deals with the reinforcement of igneous rock slopes at three open pit iron ore trines in northern Canada. The pits involved utilize overall slope angles in excess of 60º with ultimate depths in the order of 250 m. Three case studies are described. The first concerns the reinforcement of a 300,000 Ton undercut rock wedge, approximately 70 m in height. This was accomplished using 20 cm diameter steel bales, installed in 25 cm diameter vertical holes, and a cement-sand grout. The second involves the reinforcement of a 40 m wide diabase dyke which had been continuously failing as the pit deepened. A unique form of rock reinforcement was used in that the entire mass of the undercut dyke was not pinned to the wall. Rather an interlocking effect between individual blocks within the dyke was relied upon. A third concerns the reinforcement of a berm which was undercut by the contact between the ore and waste. This reinforcement was also accomplished using a combination of steel bales, rods and cement grout.

Jan 1, 1982

By K. Y. Lo, R. S. C. Wai, R. K. Rowe, L. Tham

Laboratory tests for the determination of thermo-mechanical proper- ties of three rock types were performed at temperatures up to 400°C. Results showed that for the medium and coarse Granitic Gneisses, the coefficient of thermal expansion and Young's modulus are strongly temperature and temperature history dependent. A threshold temperature exists for each rock type above which material nonlinearity becomes important, and is associated with the progress of thermal cracking. Finite element computations were performed to illustrate the influence of material nonlinearity and boundary constraint on thermal stresses. Finally, a case history of thermal spalling was analyzed and it is shown that the results of analysis are consistent with field observations.

Jan 1, 1982

By John R. Burger

Industrial mineral mines that have recently been opened, or soon will be opened in the northern circumpacific will produce potash in Canada, Mexico, and Thailand; phosphate in the US, Mexico, and Colombia; soda ash in the US; and chromite in the US and the Philippines.

Jan 1, 1982

By Richard E. Gray, Robert W. Bruhn

INTRODUCTION Underground coal mining has been practiced in the United States for over 200 years. Much early mining was not as efficient as today and unrecovered coal pillars, often of variable size and spacing, remain to support the overlying strata after mining has ceased. These conditions constitute a potential subsidence problem since the pillars will eventually fail. The possibility of subsidence above an abandoned mine must be anticipated except when total extraction has been achieved, permitting subsidence concurrent with mining, or when large coal pillars which have an adequate factor of safety for long-term support remain in the mine. Coal is found in 37 states and is mined under- ground in 22 states (HRB Singer, Inc. 1980). Underground mining produced 40 percent of the 7.5 x 10" kg. (830,000,000 tons) of U. S. coal mined in 1980 (Keystone, 1981). There are approximately 70,000 abandoned or inactive underground coal mines in the United States and approximately 2000 active underground coal mines (NAS/NAE, 1975). Underground coal mining in the United States will eventually extend beneath 162 x 109m2 (40 million acres). Thirty-two billion m2 (8 million acres) are already undermined (HRB Singer, 1977). Subsidence due to mining has affected more than 8 x 109m2 (2 million acres) in 30 states, 7.7 x 10 9m2 (1.9 million acres) from bituminous coal mining and the remainder primarily from anthracite mining (Johnson and Hiller, 1979). Subsidence from all other underground mines has affected only 6.9 x 10 7m2 (17,000 acres) (Johnson and Miller, 1979). Subsidence appears to be particularly widespread in two states, Pennsylvania and Illinois, although serious subsidence is found in localized areas of numerous other states (HRB- Singer, Inc. 1977). Host underground coal mining has occurred in the eastern United States, where the U. S. Bureau of Mines estimates 1.6 x 109m2 (398,600 acres) in urban areas in 18 states (out of a total 1.7 x 109m2 1418,400 acres]) are threatened by subsidence (Table 1) (Johnson and Miller, 1979). Pennsylvania and West Virginia contain 57 percent of the total threatened areas. The U.S. Bureau of Mines estimates the total cost to stabilize the estimated 1.7 x lo9m2 (418,400 acres) of subsidence prone urban land located above abandoned mines is over $12.5 billion (1978 costs).

Jan 1, 1982

By John Dodd

This paper reviews advances in the technology of abrasion resistant iron and steels, which could help combat abrasion and wear in mining operations. With the recent progress in high chromium alloy iron development, high temperature heat treatment of massive castings can be eliminated, aloy cost reduced, and cracking problems avoided. Data on erosion-corrosion resistance of these irons; trends in the development of improved cast steels; and factors influencing toughness and abrasion resistance of manganese steels are all considered. The 7% Mn. 1% Mo manganese steels are shown to combine toughness and abrasion resistance, and composite castings are a means of combating abrasion in applications involving severe impact. A brief appraisal is given of recently developed martensitic wrought steels with improved weldability.

Jan 1, 1982

By A. Wadood M. A. El Rabaa, William A. Hustrulid, William F. Ubbes

The spatial distribution of the deformation modulii around the CSM/ONWI test facility was determined using an NX version of the CSM cell. Approximately 840 modulus measurements were made in six rings (each ring containing seven holes each 6 m in length) of boreholes. These parallel rings were spaced at 2.4 m intervals along the room. Contour plots of the modulii revealed that the depth of the blast damage zone varied both with perimeter position and distance away from the opening. The maximum depth of disturbance appeared to be of the order of 60 cm. At locations removed from the opening, the variability in modulus was quite high reflecting the presence of joints, faults, shear zones and foliation. A comparison of rock mass modulii (ER) with those obtained from the laboratory testing of core (E), revealed that ER [=] 0.5 E.

Jan 1, 1982

By Richard R. Parizek, E. Scott Blair

Numerical modeling of ground water flow systems can be used to help analyze many practical problems encountered in the mining industry. Numerical models can be used to predict ground-water seepage rates into surface mines, shafts, and other large excavations; to predict water-level changes under adjacent properties; and to predict the effectiveness of various deep-well dewatering schemes. As with any model, the results from a numerical model are limited by the quality and quantity of data, and by the restrictions of any simplifying assumptions. A case study is presented that shows how a numerical model was used for engineering purposes to help analyze the hydrologic impact of a proposed open-pit mine by Predicting changes in the dewatering rate caused by the lateral growth and deepening of the mine and by predicting the effectiveness of various deep-well dewatering schemes.

Jan 1, 1982